Range of stop valves with either DZR brass, brass, bronze or chrome plated bodies with T-type or lockshield (LS) operating members. Compression models are for use with copper pipe manufactured to BS EN 1057. Maximum working pressure 16.0 bar.
Non-metallic materials and components comply with BS6920 at 85°C
Talbot range of gunmetal screw down stop valves for use with MDPE PE80 pipe (manufactured to EN12201). The products are supplied with loose (blue plastic) pipe inserts. Maximum working pressure 16.0 bar. Cold water use only.
Range of screw down stop valves with plastic bodies, EPDM washers and ‘O’ rings. For use with polyethylene pipe (manufactured to EN 12201). The products are supplied with loose pipe inserts. For above and below ground use. Maximum working pressure 16 bar. Cold water use only.
Range of commercial dish washing machines with flow controlled by a solenoid valve and discharged via a type `AB` airgap (verified by test - suitable for backflow protection against fluid category 5). Maximum working pressure 4.0 bar. Cold water use only.
Activflo range of water conditioners with stainless steel bodies. Models with compression connections are for use with copper pipe (manufactured to BS EN 10 57), stainless steel pipe (BS EN 10312:2002), polybutylene (BS 7291-2) or PE-X pipe (BS7291-3). Maximum working pressure 16 bar. Maximum operating temperature 99°C
'Kepital F10-01 T2, F10-02, F10-03H, F20-03M, F25-03 & F30-03M'. The following grades were added to the approval in April 2023: ‘Kepital F30-34, F10-01, F10-03HM, F20-03, F25-03M & F30-03’. Natural, unpigmented (white in appearance), injection moulded POM materials. All the grades listed can be coloured using the following masterbatch MB-S315F (black coloured masterbatch). All are for use with water up to 85°C.
'ABS Bianco CP .2503 HI70' (also known as DWKRAL ABS Bianco 4698 AT). White coloured, injection moulded ABS material. For use with water up to 35°C.
ML-9005WGL414 (black coloured - RAL 9005), ML-6018WGL424 (green coloured - RAL 6018), ML-9A10WGL444 (white coloured - RAL 9010), ML-5007WGL424 (blue coloured - RAL 5007) & ML-6621WGL424 (green coloured - Pantone 334 C). Factory applied, electro-statically sprayed epoxy powder coatings. Apply as per manufacturer’s Product Data Sheet ‘Pdb_ML-WGL414-EN (03-2023)’, dated ’23.03.2023’. Stove (cure) for 8 minutes at 180°C. For use with water up to 65°C. These materials are only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'KUBOTAPOWDER TK1413F M'. Factory applied, grey coloured epoxy resin powder coating. Apply as per manufacturer's Technical Information 'No. SG23180' dated '11 June 2021'. Cure for 10 minutes@200°C. For use with water up to 60°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'A/W AQUA (A) Epoxy 100'. Site applied, pale straw coloured epoxy/linseed oil waterproof coating. Apply as per manufacturer's Technical Document 'FSQP-707-05' dated '2021.01.04'. Cure for 6 hours under UV light (wavelength 365μm) at a distance of 150mm. For use with water up to 23°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
‘MasterProtect® 180’. Site applied, grey coloured, two-component epoxy coating consisting of Part A (grey coloured liquid) and Part B (colourless liquid). Mix Part A and Part B in a mass ratio of 87:13 and apply as per manufacturer's TDS 'MBS_CC-UAE/Pr_180/ /03_23'. Cure coat 1 for 36 hours@20°C. Cure coat 2 for 21 days@20°C. For use with water up to 40°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Maxline 100 Potable Water Coating Blue & Grey'. Site applied, two-component polyurethane coatings which are available in blue or grey colours (once mixed). Mix Part A (blue or grey opaque liquid) with Part B (amber, translucent liquid) in a 100:30.5 weight ratio and apply as per manufacturer's technical data sheet 'TDSMLI100.rv5.04042023'. Cure for 14 days@7°C. For use with water up to 23°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the materials are not covered by the scope of the approval.
'ULTRADUR B4300 GK24 HR FC AQUA GREY 35413'. Grey coloured, injection moulded PBT material. For use with water up to 85°C.
'Dowlex 2344'. Natural (appears white), compression moulded LLDPE material. From May 2025, the material may also be used for extrusion purposes. For use with water up to 85°C.
'AY-N130X series'. Injection moulded PPE materials. For use with water up to 85°C. • AY-N130X-GY843 – grey coloured (contains 30% maximum glass fibre, 2% maximum white pigment, 0.01% maximum black pigment). • AY-N130X-YW05 – yellow coloured (contains 30% maximum glass fibre, 1.5% white pigment, 0.5% maximum yellow pigment). • AY-N130X-BK001 – black coloured (contains 30% maximum glass fibre, 0.5% maximum black pigment).
'Innopol CS 4-8000 G'. Grey coloured, compression moulded polypropylene material. For use with water up to 60°C.
'UW61424 & UW61427 – Instinct'. White coloured, extruded PTFE tapes. For use with water up to 85°C.
'Superfast Steel (SFST)'. Epoxy putty which has a grey coloured outer layer, a black coloured inner layer and is grey coloured once mixed. Mix layers by hand until a homogenous colour is achieved and then apply as per product label. Cure for 24 hours@7°C. For use with water up to 23°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'7EP2114 'O'-rings'. Black coloured, injection moulded EPDM 'O'-rings. Shore hardness 70. Tested in-radius size 0.9mm. For use with water up to 85°C.
'4255 Washers', with a tested in-radius size of 1.0mm. '4255 ‘O’ rings', with a tested in-radius size of 1.31mm were added to the approval in September 2023. Black coloured, injection moulded EPDM washers & ‘O’ rings. Shore hardness of 50. For use with water up to 85°C.
'5594610'. Black coloured, compression moulded EPDM material. Shore hardness 60. Tested in-radius size 1.0mm. For use with water up to 85°C.
'ROGM 2022 'O' ring'. Black coloured, injection moulded NBR 'O' ring. Shore hardness 70. Tested in-radius size 4.4mm. For use with water up to 23°C.
'Durapipe FIP & Astore PVCu Clear Solvent Cement'. Clear, colourless solvent cements. Apply as per manufacturer's instructions and cure/dry for 24 hours@5°C. For use with water up to 23°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
Single hole, single outlet (fixed) electronically controlled combination tap assemblies (chromium plated). The flow is controlled by a solenoid valve activated via an infra-red sensor. Spout outlet incorporates a plastic aerator. Maximum working pressure 10.0 bar.
Non-metallic materials and components comply with BS6920 at 60°C
Range of single hole, single outlet, electronically controlled tap assemblies (chrome plated brass body). The flow is controlled by a solenoid valve activated via an infra-red sensor. The spout outlet incorporates a plastic aerator. Supplied with a stainless steel braided PEX lined flexible connection hose and a manual lever for controlling the temperature. Maximum working pressure 8.0 bar.
Non-metallic materials and components comply with BS6920 at 65°C
Range of single hole, single outlet (fixed) combination tap assemblies (chrome plated – brass bodies). Flow is controlled via a solenoid which is actuated via an infrared sensor and the temperature is controlled by a manual lever. The spout outlets incorporate plastic aerators. The inlet hoses incorporate stainless steel strainers and an approved check valve cartridge; however, the complete product has not been fully tested to demonstrate it provides backflow protection. Maximum working pressure 8.0 Bar.
Non-metallic materials and components comply with BS6920 at 60°C
Range of single hole, single outlet, electronically controlled tap assemblies (brass body – various finishes). The flow is controlled via a solenoid valve and activated by an infra-red sensor on the front of the spout. The spout outlet incorporates a plastic aerator. Models xxx.yyy.170E/W are supplied with a click clack waste. Maximum working pressure 5.0 bar.
Non-metallic materials and components comply with BS6920 at 60°C
WC flushing cistern incorporating a side entry BS 1212-4 compact type float operated inlet valve providing a Type AG air gap with a dual flush drop valve for full flush volumes of up to 6 litres and a reduced flush of up to 4 litres. The cistern is operated by a manual push button and incorporates a servicing valve on the inlet supply. Maximum working pressure 10.0 bar. Cold water use only.
Concealed WC dual flushing cistern with a bottom entry BS 1212 - 4(2016) float operated inlet valve providing a Type AG air gap arrangement and a dual flush outlet valve. The flush volume is operated by a two-push button assembly for a 6 or 3 litre flush volume. Maximum working pressure 10.0 bar, cold water use only.
Range of ceramic cartridge headworks with plastic bodies, for insertion into specifically dimensioned bores. Maximum working pressure 10.0 bar.
Non-metallic materials and components comply with BS6920 at 70°C
Quarter turn ceramic disc headwork with brass body, NBR and silicone rubber ‘O’ rings, for insertion into specifically dimensioned tap assemblies. Maximum working pressure 10.0 bar. Maximum operating temperature 90°C
Non-metallic materials and components comply with BS6920 at 90°C
Range of single hole single outlet fixed combination tap assemblies, (chrome plated brass), incorporating quarter turn ceramic disc headworks with a single lever operating member and non-rising spindle headwork with a variety of operating members (See models) controlling the flow to the additional swivel spout. The product incorporates a hand held pre-rinse spray with a self-closing trigger, either on a flexible hose within an overhead spring or as a fixed length flexible hose on a swivel arm (see model). The inlets incorporates an approved check valve cartridge, however, the complete product has not been fully tested to demonstrate it provides backflow protection. The outlet of the swivel spouts incorporates plastic aerators. These products are supplied with metal back nuts. Maximum working pressure 8.6 bar.
Non-metallic materials and components comply with BS6920 at 65°C
Range of single hole single outlet fixed combination tap assemblies, (chrome plated brass), incorporating a quarter turn ceramic disc headwork with a single lever operating member and non-rising spindle headwork with a variety of operating members (See models) controlling the flow to the additional swivel spout. The product incorporates a handheld pre-rinse spray with a self-closing trigger, either on a flexible hose within an overhead spring or as a fixed length flexible hose on a swivel arm (see model). The inlets incorporates an approved check valve cartridge; however, the complete product has not been fully tested to demonstrate it provides backflow protection. The outlet of the swivel spouts incorporates plastic aerators. Maximum working pressure 8.6 bar.
Non-metallic materials and components comply with BS6920 at 65°C
Range of single hole, single outlet (fixed) combination tap assemblies with (brass bodies - various finishes), incorporating ceramic cartridge headworks and single lever operating members. The spout outlet incorporates a plastic aerator. All models are supplied with a pop-up waste. Maximum working pressure 10.0 bar.
Non-metallic materials and components comply with BS6920 at 60°C
Single hole, single outlet (fixed) combination tap assembly with brass body (various finishes), incorporating ceramic cartridge headwork and a single lever operating member. The spout outlet incorporates a plastic aerator and the product is supplied with a lever operated pop-up waste. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C
Range of single hole, single outlet (fixed) combination tap assemblies, (brass bodies - various finishes) incorporating a ceramic cartridge headworks with single lever operating members. The spout outlet incorporates either a plastic aerator or flow straightener, (Model 193838EX,193838EX MBK1, 163838EX & 163838EX MBK1 is only supplied with an aerator) . The product is supplied with a click type waste (verified by test). Maximum working pressure 5.0 bar.
Non-metallic materials and components comply with BS6920 at 65°C
Single-hole, single outlet fixed combination tap assembly (chrome plated brass body), incorporating a ceramic cartridge headwork with a single lever operating member. The spout outlet incorporates a plastic flow straightener. The product is supplied with a click type pop-up waste. Maximum operating pressure 10.0 bar.
Non-metallic materials and components comply with BS6920 at 65°C
Range of single hole, single outlet (fixed) combination tap assemblies (chrome plated brass bodies), incorporating ceramic cartridge headworks with single lever operating members. The spout outlets incorporate plastic aerators. The products are supplied with a click type pop-up waste. Maximum working pressure 10.0 Bar Maximum operating temperature 60°C
Non-metallic materials and components comply with BS6920 at 60°C
Single hole, single outlet (fixed) combination tap assembly (brass bodies - various finishes), incorporating a ceramic cartridge headwork with a single lever operating member. The spout outlet incorporates a plastic aerator. Maximum working pressure 5.0 Bar.
Non-metallic materials and components comply with BS6920 at 85°C
Range of single hole, single outlet, fixed, combination tap assemblies (brass bodies - various finishes ) incorporating a ceramic cartridge headwork and single lever operating member. The spout outlet incorporates a plastic aerator. Products are supplied either with or without a lever type pop-up waste set (see models). Maximum working pressure 10.0 bar.
Non-metallic materials and components comply with BS6920 at 60°C
Range of single hole, single outlet (fixed) combination tap assemblies (brass bodies - various finishes), incorporating detent (push to open, push to close) type headworks controlling both temperature and flow with a dome operating member. The spout outlet incorporates a plastic aerator. The inlet hoses incorporate stainless steel strainers and approved check valve cartridges; however, the complete product has not been fully tested to demonstrate it provides backflow protection. The products are supplied with a lever type pop up waste. Maximum working pressure 10.0 Bar.
Non-metallic materials and components comply with BS6920 at 70°C
Range of single hole, single outlet (fixed) combination tap assemblies (brass bodies - various finishes), incorporating a ceramic cartridge headworks with a single lever operating member. The spout outlet incorporates a plastic aerator. The product is supplied with a click type pop-up waste or lever type pop up waste. Maximum working pressure 10.0 Bar.
Non-metallic materials and components comply with BS6920 at 60°C
Range of deck mounted, single hole, single outlet (fixed) combination tap assembly (chromium plated brass), incorporating a ceramic cartridge headworks and various type operating members (see models). The outlet incorporates a plastic aerator. Maximum working pressure 10.0 bar.
Non-metallic materials and components comply with BS6920 at 60°C
Range of single-hole, single outlet, fixed combination tap assemblies (chrome plated brass bodies), incorporating quarter turn ceramic disc headworks with cross top operating members. The spout outlets incorporate plastic flow straighteners. The products are supplied with lever operated pop-up wastes. Maximum working pressure 10.0 Bar
Non-metallic materials and components comply with BS6920 at 65°C
Range of floor mounted, single hole, single outlet fixed combination tap assembly (various finishes), incorporating a ceramic cartridge headwork with a single lever operating member and a self-cancelling diverter to shower outlet. The outlet to the shower incorporates an approved check valve cartridge, however the complete product has not been fully tested to demonstrate it provides backflow protection. The spout outlet incorporates an aerator. These products are not supplied with shower handset and hose. Maximum working pressure 16.0 bar. Between May 2023 and July 2023, the taps have a maximum operating temperature of 65°C. From August 2023 the taps have a maximum operating temperature of 60°C.
Range of single hole, single outlet (swivel) combination tap assemblies (various finishes) with under counter boiling water unit (vented via the spout outlet) and in-line water filter (on instantaneous hot water supply only). Flow is controlled by a ceramic cartridge headwork with a single lever operating member. Instantaneous hot water is controlled by a self-closing quarter turn ceramic disc headwork with a single lever operating member. The product is supplied with loose 3/8” x 15mm reducers and approved check valve cartridges, however, the complete product has not been fully tested to demonstrate it provides backflow protection. The spout outlets incorporate a plastic aerator. Maximum working pressure 8.6 bar. Maximum operating temperature 98°C.
Range of single hole, single outlet (swivel) combination tap assemblies (chrome plated brass bodies) incorporating ceramic cartridge headworks with single lever operating members. The spout outlets incorporate plastic aerators. Maximum working pressure 5.0 Bar
Non-metallic materials and components comply with BS6920 at 60°C
Single hole, single outlet (swivel) combination tap assembly, (chrome plated brass body) incorporating ceramic cartridge headwork with a single lever operating member. The spout outlet incorporates a plastic aerator. Maximum working pressure 4 bar.
Non-metallic materials and components comply with BS6920 at 65°C
Range of two-hole, single outlet (fixed) combination tap assemblies (chrome plated brass). Model T740005 incorporates ceramic cartridge headwoks. All other models incorporate quarter turn ceramic disc headworks with single lever operating members. Spout outlets incorporate plastic flow straighteners except T8705 with is open. All products are supplied with metal back nuts. T7505M, T8705, T8805, T7115 and T749005 maximum working pressure 5.0 bar, Maximum operating temperature 60°C. T739005 maximum working pressure 16 bar max operating temperature 65°C. T740005 maximum working pressure 10 bar max operating temperature 65°C.
Range of wall mounted, two hole, single outlet combination tap assemblies, (brass bodies - various finishes), incorporating ceramic cartridge headworks with single lever operating members. The spout outlets incorporate plastic aerators. Maximum working pressure 10.0 bar.
Non-metallic materials and components comply with BS6920 at 60°C
Page 43 of 131
We use cookies to give you the best possible experience with WRAS. Some are essential to provide website functions and ensure the website is secure. We also use cookies to help us understand how people use the site and to make improvements. Click "Accept All" to enable recommended settings or click "Manage cookies" to adjust your settings. For more details, see our Cookie Policy.
