'FY Portland Cement Mortar'. Factory applied, grey coloured Portland cement mortar. Mix cement:sand:water in a 2:1:0.4 mass ratio and apply as per manufacturer's instructions issue reference 'FR20240910', dated '2024-09-10'. Cure for 12 hours@55°C. For use with water up to 65°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the materials are not covered by the scope of the approval.
'Sigmaguard CSF 585/Blue' (included on the initial approval) is for use with water up to 50°C. 'Sigmaguard CSF 585/RAL5017’ was added to the approval in December 2025 and is for use with water up to 40°C. Factory applied, blue coloured, two-component, solvent-free epoxy coatings. Mix parts A & B in a volume ratio of 77.5:22.5 and apply as per manufacturer's Product Data Sheet '7785', dated 'August 19, 2022'. Cure for 12 days@20°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the materials are not covered by the scope of the approval.
'ULTRAMID® D3EG12 AQUA BLACK 102'. Black coloured, injection moulded PA material. For use with water up to 85°C.
'NB01280PWRC'. Black coloured, compression moulded NBR rubber material. Shore hardness 80. Tested in-radius size 1.0mm. For use with water up to 85°C.
'NB012370P(KAWN)'. Black coloured, compression moulded NBR material. Shore hardness 70. Tested in-radius size 1.0mm. For use with water up to 85°C.
Bottom entry A1370A and side entry A1423B BS1212-4 (2016) compact type float operated valves for WC flushing cisterns. The inlet incorporates a strainer. A1270A - plastic or brass connector. A1423B - plastic connector only. Maximum working pressure 10.0 bar. Cold water use only.
Bottom entry BS1212-4 (2016) compact type float operated valves for use with WC flushing cisterns. The inlet incorporates a strainer. Maximum working pressure 10.0 bar. Cold water use only.
WC flushing cistern incorporating a side entry BS 1212-4 compact type float operated inlet valve providing a Type AG air gap with a dual flush drop valve for full flush volumes of up to 6 litres and a reduced flush of up to 4 litres. The cistern is operated by a manual push button and incorporates a servicing valve on the inlet supply. Maximum working pressure 10.0 bar. Cold water use only.
Range of wall hung concealed WC flushing cisterns with a BS 1212-4 float operated inlet valve providing a Type AG air gap arrangement and a dual flush outlet valve. The flush volume is operated by a push button assembly. Maximum working pressure - 10 Bar. Cold water use only.
Range of single hole, single outlet (fixed) over the rim (swivel nozzle) bidet combination tap assemblies (brass bodies - various finishes), incorporating a ceramic cartridge headworks with a lever type operating member. The spout outlet incorporates a metal aerator. The product is supplied with a lever type pop up waste. Maximum working pressure 3.5 bar. Maximum operating temperature 60°C.
Range of ceramic cartridge headworks with plastic bodies. For insertion into specifically dimensioned bores. Maximum working pressure 10.0 bar. Maximum operating temperature 65°C
Range of thermostatic cartridges with either brass or plastic bodies, for insertion into specifically dimensioned bores. Maximum operating temperature 85°C.
Range of single hole, single outlet (fixed) combination tap assemblies (brass body, various finishes - see model) incorporating a ceramic cartridge headwork with a single lever operating member. The spout outlet incorporates a plastic aerator. Maximum working pressure 10.0 bar. Maximum operating temperature 65°C.
Single hole, single outlet fixed combination tap assemblies (chrome plated brass body), incorporating quarter turn ceramic disc headworks with cross-top operating member. The spout outlet incorporates a plastic flow straightener. The product is supplied with a click type pop-up waste (verified by test). Maximum operating pressure 5.0 bar. Maximum operating temperature 60°C.
Range of single hole, single outlet (fixed) combination tap assemblies (brass bodies - various finishes) incorporating a ceramic cartridge headworks with single lever operating members. The spout outlet incorporates a plastic aerator. Supplied with a pop-up waste. Maximum working pressure 5.0 Bar. Maximum operating temperature 60°C.
‘Arco,’ ‘Zero,’ ‘Slim’ & ‘Trenta9’ ranges of wall mounted two-hole, single outlet (fixed) combination tap assemblies (chromium plated brass), incorporating a ceramic cartridge headwork and either a single lever operating member (Trenta9 models) or dome type operating member (all other models). The spout connection of the Arco models incorporates a plastic flow regulator. The spout outlet of all other models incorporates a plastic aerator. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.
Two-hole, single outlet (swivel) combination tap assemblies (brass bodies - various finishes). Incorporating quarter turn ceramic disc headworks and single lever type operating members. The spout outlet incorporates a plastic aerator, and the products are supplied with metal backnuts. Maximum working pressure 10.0 Bar Maximum operating temperature 65.0°C
Range of three hole, single outlet (fixed) combination tap assemblies, (brass bodies - various finishes) incorporating quarter turn ceramic disc headworks with various operating members. The spout outlet incorporates a plastic aerator and is connected to the headworks via stainless steel braided TPSiV lined hose assemblies Maximum working pressure 3.5 bar. Maximum operating temperature 60°C
Range of cylindrical expansion vessels with epoxy coated or uncoated steel bodies and Butyl membranes. Maximum working pressure 10.0 Bar (15.0 bar INOX PRO 0.16L). Maximum operating temperature 99.0°C.
Range of shower and tap filters with plastic bodies. Maximum working pressure 5.0 bar. Maximum operating temperature 60°C
Range of “JRG Sanipex MT” compression fittings for use with “JRG Sanipex MT” multilayer pipes (PE-Xc/Al/PE-Xb 16x2,25mm to 40x3,5mm and PE-Xc/Al/PE-Xc 50x4,0mm and 63x4,5mm). Maximum working pressure 10.0 bar. Maximum operating temperature 85°C for dimensions 16x2,25 mm to 40x3,5 mm. Maximum operating temperature 60°C for dimensions 50x4,0 mm and 63x4,5 mm.
Range of press fittings (brass bodies - various finishes) with stainless steel press (‘TH’ profile) collars and EPDM O-rings for use with “EA” range of PEX/AL/PEX multilayer pipe (for press fitting connections and compression for EHA adaptor fittings only) or copper pipe manufactured to EN1057 (compression connections). Maximum operating temperature: 95°C. Maximum operating pressure: 10 bar.
‘Tweetop LBP system’ consisting of brass bodied press fittings for use with ‘Tweetop multilayer pipe’ PE-RT II/AL/PE-RT II. The press fitting is achieved by use of a press fitting tool (‘U’ or ‘TH’ crimping profiles). Maximum working pressure: 10.0 Bar. Maximum working temperature: 95°C.
Instinct range of U profile press fittings (nickel plated brass bodies) for use with Instinct range of PERT/AL/PERT multi-layered pipes. Maximum working pressure 10.0 bar. Maximum operating temperature 95°C.
‘HS100’ range of compression fittings with brass, nickel plated brass or DZR bodies for use with copper pipe (manufactured to EN 1057). For above ground use only. Max working pressure 16.0 bar. Max operating temperature 85°C.
‘FRABOPRESS 316 M’ range of stainless-steel press fittings for use with stainless steel pipe (manufactured to EN 10312:2002 & EN 10217:2021). Maximum working pressure 16.0 bar. Maximum operating temperature 100°C.
Range of stainless steel press fittings: SS316L stainless steel models are for use with SS316L stainless steel pipe manufactured to EN 10312.; SS304 stainless steel models are for use with SS304 stainless steel pipe manufactured to EN 10312. Crimp joint is achieved by a M profile crimp jaws. For above ground use only. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Range of stainless-steel press fittings (SUS304 or 316L) with EPDM ‘O’-rings for use with stainless-steel pipe (SUS304 or 316L EN 10312), using an ‘M’ press profile. Maximum working pressure 16.0 Bar. Maximum operating temperature 85°C.
Range of copper crimped fittings with EPDM ‘O’-rings for use with copper pipe manufactured to EN1057. For above and below ground use. Maximum working pressure 16 Bar. Maximum operating temperature 99°C.
DMFit range of black, grey and white plastic pushfit fittings for use with DM LLDPE pipes or PEX barrier pipe manufactured to BS7291-3. (White fittings were added to the approval in August 2025). When used with DM LLDPE tubing the supplied black or grey pipe inserts (ATS) must be installed. When used with PEX barrier pipe the supplied beige pipe inserts must be installed. DM LLDPE tubing are available in black, natural (appearance is white), white, red, and blue colours. Maximum working pressures and temperatures: When used with DM LLDPE tubing: 4-15mm & 5/32”-½” pushfit sizes: 12.0 bar, cold water use only. 6-15mm & ¼”-½” pushfit sizes: 7.0 bar @ 65°C. When used with PEX Barrier pipe (manufactured to BS7291-3): 15-22mm pushfit sizes: 12.0 bar, cold water use only and 7.0 bar @ 65°C. Fittings which incorporate 4-10mm & 3/16” - ⅜” barb connections: 12.0 bar, cold water use only. Fittings which incorporate ½” - ¾” barbed end connections are open outlet use only. Maximum operating temperature 65°C.
“<A> Press Copper M Profile” series press fittings with a copper body and EPDM ‘O’-rings, for use with copper pipe manufactured to EN1057. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Press-Inox range of stainless-steel crimped fittings (‘M’ crimp profile) for use with stainless steel pipe (manufactured to EN10204). For above ground use only. Maximum working pressure: 16Bar. Maximum operating temperature: 100°C.
Range of water meter manifolds with plastic bodies for use with PE80 pipe (manufactured to BS EN 12201). The inlets incorporate a spherical valve and a check valve cartridge however, the complete product has not been fully tested to demonstrate it provides backflow protection. Maximum working pressure 16.0 bar. Cold water use only.
Range of water meter manifolds with plastic bodies for use with PE80 pipe (manufactured to BS EN 12201). The inlet incorporates a stop valve. Model MB77025AM Matrix Single (CV) incorporates a single check valve cartridge and model MB77025DCV Matrix Dual (DCV) incorporates two, single check valve cartridges however, the complete products have not been fully tested to demonstrate it provides backflow protection. Maximum working pressure 16.0 bar. Cold water use only.
Nova-Flo’ inline flow control device with a plastic body. The product is intended to restrict the flow of water to a bath or basin if water level reaches the overflow. Float located within the overflow pathway activate flaps on each inlet to restrict the flow prior to the taps being closed. Maximum working pressure: 12 Bar. Maximum working temperature: 60°C.
Range of plastic pressure sensors. Maximum working pressure: 15.99 Bar. Maximum operating temperature 90.0°C.
Range of horizontal multistage pumps with stainless steel bodies, diffuser and impellers and EPDM ‘O’-rings. The products incorporate a graphite-SiC-EPDM shaft seal. The products incorporate a drain plug. Maximum working pressure 8.5 bar. 9Maximum operating temperature 80°C.
Range of vertical (CVM) or horizontal (CHM) multistage pumps with stainless-steel bodies and stainless-steel impellers, intermediate chambers, shaft and outer sleeve and EPDM seals. Maximum working pressure: 25 Bar. Maximum working temperature: 23°C.
Range of multistage and single stage water pumps with stainless steel bodies and impellers. Maximum working pressure 2.0 bar (AMS models), 4.0 bar (EDH & EMH models) 8.0 bar (LVS models). Maximum operating temperature 85°C
Range of pumps with stainless steel bodies. Maximum working pressure depends on model, please refer to model. Maximum operating temperature 65°C.
Range of shower handsets and overhead showers, (plastic bodies - various finishes). The inlets incorporate a plastic flow restrictor and stainless steel strainer. Maximum operating temperature 60°C. Open outlet use only.
Range shower outlets and accessories with brass bodies (various finishes). The inlet of the overhead shower outlet incorporates a stainless steel strainer. Maximum operating temperature 85°C. Open outlet use only.
Range of overhead shower outlets, (brass bodies – various finishes) incorporating NBR O rings. Maximum operating temperature: 65C
Range of shower handsets with (plastic bodies - various finishes Maximum operating temperature 60°C. Open outlet use only.
Range of shower handsets and connection hoses (brass bodies – various finishes). The inlet incorporates an approved check valve cartridge (with plastic flow regulator) however, the complete product has not been fully tested to demonstrate it provides backflow protection. Open outlet use only. Maximum operating temperature 60°C
Range of wall mounted hose union bib taps incorporating a rising spindle headwork with a T - handle operating member and brass body. The spout outlets incorporate a hose union connector. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Pillar tap (chrome plated brass body) incorporating quarter turn ceramic disc headwork with cross top operating members. The spout outlet incorporates a plastic flow straightener. The product is supplied with metal backnuts. Maximum working pressure 5.0 bar. Maximum operating temperature 60°C.
Range of black HDPE Pipe SDR 11 manufactured to ISO 4427 / DIN 8074 / EN12201. Maximum working pressure: 16 Bar. Maximum operating temperature: Cold water use only.
Range of stainless steel braided hoses, incorporating a dual layered hose consisting of a clear PE liner and black coloured EPDM outer layer. The SOG1212XXX(GLF)CS model incorporates an isolation valve. The models with compression connections are for use with copper pipe (manufactured to EN 1057). Maximum working pressure 10.0 bar. Maximum operating temperature 85°C.
Range of stainless steel braided PEX lined flexible hose assemblies with EPDM washers and/or ‘O’-rings, and brass end connections. The 15mm compression connection incorporates an isolation valve. The models with compression connections are for use with copper pipe (manufactured to EN 1057). Maximum working pressure 10.0 bar. Maximum working temperature 85°C.
Page 31 of 50
We use cookies to give you the best possible experience with WRAS. Some are essential to provide website functions and ensure the website is secure. We also use cookies to help us understand how people use the site and to make improvements. Click "Accept All" to enable recommended settings or click "Manage cookies" to adjust your settings. For more details, see our Cookie Policy.
