Wall mounted shower outlet with chrome plated body. The inlet incorporates a flow regulator and an approved check valve cartridge, however, the complete product has not been fully tested to demonstrate it provides backflow prevention. Maximum operating temperature 60°C
Range of shower outlets and shower arms (brass bodies - various finishes - see model). The wall mounted and ceiling mounted shower heads incorporate integral plastic flow regulators and also include stainless steel strainers on the inlets. The shower handset has a plastic flow regulator and a stainless steel strainer on the inlet. Maximum operating temperature 60°C.
Range of shower handsets with a black plastic body and EPDM ‘O’-rings. Model includes a trigger mechanism that alters the spray pattern. Maximum operating temperature 60°C.
Range of pillar taps (chromium plated brass), incorporating quarter turn ceramic disc headworks with single lever, dome type or cross top operating members and plastic backnuts. The spout outlets incorporate a plastic flow straightener. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.
Range of wholesome-water nickel plated brass manifolds for use with ‘Emmeti Gerpex RA’ Pexb/Al/Pexb Multilayer pipe and ‘Emmeti Alpert’ PERT/AL/PERT Multilayer Pipe. Maximum working pressure 10.0 bar. Maximum operating temperature 95°C. Range of closed circuit use nickel plated brass manifolds for use with ‘JG Speedfit Layflat Polybutylene Barrier Pipe (models 10BPB & 15BPB)’. Maximum working pressure 3.0 bar. Maximum operating temperature 92°C.
Range of concealed manually operated blending valves (brass bodies with chromium plated exposed trim sets) incorporating self-cancelling diverters (except models added December 2023 – 36020626 & 36020832) ceramic cartridge headworks controlling both temperature and flow with a single lever operating member. The inlets and the outlet incorporate approved check valve cartridge however the complete product has not been fully tested to demonstrate it provides backflow protection. Maximum working pressure 10.0 bar. Maximum operating temperature 80°C.
Wall mounted, manual blending shower valve, (chromium plated brass), incorporating quarter turn ceramic disc headworks with cross top operating members and a manual diverter to two shower outlets. The product is supplied with a shower riser, overhead shower rose, shower hose and handset. Each inlet incorporates a combined NBR washer and stainless-steel strainer, and an approved check valve cartridge, however, the complete product has not been fully tested to demonstrate it provides backflow protection. Maximum working pressure 10.0 Bar. Maximum working temperature 60°C.
Range of concealed thermostatic valves with thermostatic cartridges. Some models include diver between outlets. (See model codes) All models incorporate cube, dome, cross-top or single lever type operating members. The inlets incorporate stainless steel strainers and single check valve cartridges; however, the complete products have not been fully tested to demonstrate it provides backflow protection. Maximum working pressure 10.0 bar. Maximum operating temperature 65°C.
Range of wall mounted thermostatic shower valves (chrome plated brass). Flow is controlled by a ceramic disc diverter cartridge, using dome type operating members. Temperature is controlled independently via a thermostatic cartridge using a dome type operating member which also incorporates a manual override button. Both inlets incorporate stainless steel strainers and approved check valve cartridges, however, the complete products have not been fully tested to demonstrate it provides backflow protection Maximum working pressure 5.0 bar. Maximum operating temperature 60°C
Two-hole wall mounted thermostatic mixing valve (chrome plated brass body). Incorporating ceramic disc headwork, with a lever type operating member. The temperature is controlled independently via a thermostatic cartridge with a lever type operating member and manual override button. Both inlets incorporate approved check valve cartridges, however, the complete product has not been fully tested to demonstrate it provides backflow protection. Maximum working pressure 10 bar. Maximum operating temperature 60°C
Range of wall mounted, bar type thermostatic blending valves (chromium plated brass) incorporating a quarter turn ceramic disc headwork controlling the flow with dome operating member incorporating a manual override button. The temperature is controlled by a thermostatic cartridge with dome or cube type operating member incorporating a manual override button. Both inlets incorporate a stainless-steel strainer and single check valve cartridge (however, the complete product has not been fully tested to demonstrate it provides backflow protection). Maximum working pressure 10.0 bar. Maximum operating temperature 65°C.
Range of piston type float operated inlet valves with brass bodies and backnuts. Maximum working pressure 8.0 or 10.0 bar (please refer to model). Cold water use only.
Range of pilot operated, adjustable, pressure reducing control valves, incorporating stainless steel bodies & strainers and EPDM ‘O’ rings & diaphragm. Auxiliary components include stainless steel tubing and isolation valves. The product is available with the following adjustable outlet pressures: 0 - 3.0 bar (silver spring), 1.0 - 8.0 bar (black spring), 1.0 - 16.0 bar (red spring). Maximum supply pressure 16.0 bar. Maximum operating temperature 65°C.
Pressure relief valve with a plastic body and EPDM diaphragm with manual easing gear. Pre-set at 3.0 bar. Model 31030030 is pre-set at 2.5 bar. Model 31030070 is pre-set at 4.5 bar. Maximum operating temperature 90°C.
Range of latching and non-latching solenoid valves with a plastic body (all models, except for 07230017 & 07230018 models added September 2023) and an EPDM diaphragm. The inlet incorporates a stainless-steel strainer. Maximum working pressure 8.0 bar. Maximum operating temperature 65°C.
Lever operated spherical valve with brushed chrome brass body, EPDM O-rings and PTFE gaskets. The valve incorporates a stainless steel filter with EPDM O-ring and brass filter plug. The compression connection is to be used with for polyethylene pipe PE100 to EN12201. Maximum working pressure 25.0 bar. Cold water use only.
Range of spherical valves with brass (CW617N) or DZR brass (CW511L) bodies (chrome plated, nickel plated or without plating - see model), chrome plated brass ball and a range of different operating members (see model). Compression connections are for use with copper pipe (manufactured to EN 1057). Maximum working pressure 10.0 bar. Maximum operating temperature 85°C.
Range of ball valves with nickel plated brass bodies, chrome plated brass ball, PTFE seats, and either lever or T handle operating members (see models). Maximum working pressure 16.0 to 64.0 Bar (Size & model dependant, see models) Maximum working temp 85°C
Range of gate valves with brass bodies and wedge with either a lock shield or non-rising spindle operating mechanism for use with copper pipe (manufactured to EN 1057). Maximum working pressure 6.0 Bar Maximum operating temperature 95.
Range of gate valves with a non-rising spindle and a handwheel operating member with a brass body and brass wedge. For use with copper pipe (manufactured to EN1057). Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Range of screw down stop valves with brass bodies and bonnets and EPDM seats. Maximum working pressure 20.0 bar. Cold water use only.
Range of screw down angle valves with brass bodies (chromium plated) and NBR ‘O’-rings with a dome type operating member. For above ground use only. Maximum working pressure 10.0 bar. Maximum operating temperatures: model 510052 = 95°C and model 510060 = 85°C.
'DURACON® M25-44 WK2001, M90-44 WK2001 & M270-44-WK2001'. White coloured, injection moulded POM materials. For use with water up to 85°C.
'MAT901 & MAT902'. In June 2025 ‘MAT901IT & MAT902IT’ washers were added to the approval. Black coloured carbon/PTFE washers manufactured by pressing. For use with water up to 85°C.
'A-95 sealing plate'. White coloured, compression moulded sealing plate. For use with water up to 85°C.
'AO-96 Sealing Ring'. Black coloured, compression moulded, ceramic sealing ring. For use with water up to 85°C.
'Eurokote® 448 Bleu 5005 & Eurokote® 448 Bleu 5002'. Factory applied, blue coloured, two-part epoxy coatings consisting of a resin and hardener. Mix resin and hardener in a 1:1 volume ratio and apply as per manufacturer's technical data sheet version dated '29/08/17'. Cure for 7 days@20°C. For use with water up to 23°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'S' epoxy powder coating. Factory applied, blue coloured epoxy powder coating. Apply as per manufacturer's instructions 'SNC-EP09V1 - date 2009/12/1'. Cure for 24 hours@30°C. For use with water up to 50°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Eurokote 468 Thixo Brun Rouge'. Factory applied, red/brown coloured, two-part epoxy coating consisting of a resin and hardener. Mix resin and hardener in a weight ratio of 77:23 and apply as per manufacturer's Data Sheet dated '10/05/2019'. Cure for 10 days@20°C. For use with water up to 60°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Powercron® 451 A – CP 573 B ITT Lowara'. Factory applied, blue coloured cationic resin coating. Apply as per manufacturer's technical data sheet 'LT/I-21-090' dated 'Sep 9, 2021'. Cure for 20 minutes@180°C. For use with water up to 50°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'NOA FWT BUFF/NOA FWT WHITE (ORGA1000 NOA BUFF/ORGA 1000 NOA WHITE). NOA FWT BUFF/NOA FWT BULE (ORGA1000 NOA BUFF/ORGA 1000 NOA BULE). NOA FWT BUFF/NOA FWT CREAM (ORGA1000 NOA BUFF/ORGA 1000 NOA CREAM)'. Factory applied, two-component white, blue & cream coloured epoxy coatings. Mix base and hardener in a 3.71:1 volume ratio and apply as per manual reference '14-11' dated 'July 2019 (ES)'. Cure for 16 hours@23°C. For use with water up to 23°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the materials are not covered by the scope of the approval.
'Eurokote 480 FC'. Site applied, red coloured (once mixed), two part epoxy coating consisting of a resin and hardener. Mix, apply and cure (fully dry) in accordance with manufacturer's technical data sheet dated 23/09/2021. For use with water up to 23°C.
'Belzona 5892'. Site applied, epoxy coating consisting of Belzona 5892 (white – Parts A & B) & Belzona 5892 (grey – Parts A & B). Belzona 5892 (white – Parts A & B) are mixed in a weight ratio of 5.7:1 and then applied as a first coat (no cure) in accordance with manufacturer’s instructions for use ‘FN10106’, publication number ’04-11-20(01)’. Belzona 5892 (grey – Parts A & B) are mixed in a weight ratio of 5.7:1 and then applied to the white in accordance with manufacturer’s instructions for use ‘FN10106’, publication number ’04-11-20(01)’. The final coating is then cured for 24 hours@30°C. For use with water up to 85°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the materials are not covered by the scope of the approval.
'Polyurea Rayston'. Site applied, blue coloured, two-component polyurea coating consisting of Component A, Component B and Component C (Pigment Paste). Mix & apply as per manufacturers datasheet dated 13/09/22. For use with water up to 60°C. This approval is valid only for the material when it is applied by experienced, suitably trained applicators that are authorized and/or certified by Krypton Chemical, S.L. The authorization, training and certification of the local applicators are the responsibility of Krypton Chemical, S.L. and not the responsibility of WRAS.
'Interline 925 Cream'. Site applied, cream coloured, two-component, solvent free epoxy coating. Mix part A (white liquid) with part B (yellow liquid) in a volume ratio of 3:1 and apply as per manufacturer’s TDS ref. ‘2252’ dated 17/12/2020. Cure for 7 days@25°C. For use with water up to 60°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Cementitious Coating 851 Grey'. Site applied, two part, grey coloured cementitious waterproof mortar which can be applied as a one-coat or two-coat system Mix liquid (Part A) and powder (Part B) in a weight ratio of 1:3.92 and apply as per manufacturer’s instructions 'Bulletin No.851 /031/012' dated July 2021. When using as a one-coat system cure for 21 days@7°C. When using as a two-coat system cure coat one for 1 hour@7°C and cure coat two for 21 days@7°C. For use with water up to 23°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'4MID 9B22150 W-A BBK'. Black coloured, injection moulded PA6 material. For use with water up to 85°C.
'Grilamid LBKN-50H FWA natural, Grilamid LBKN-30H FWA natural, Grilamid LBKN-50H FWA black 9225 & Grilamid LBKN-30H FWA black 9225'. Natural (appears light grey) and black coloured, injection moulded nylon materials. For use with water up to 85°C.
‘Dowlex 2631UE & Dowlex 2631.10UE’ Natural (appear white coloured). ‘RX 102 Natural, RX 102 Black 9003 & RX 102 GR Black 9003’ (black coloured). In April 2025 ‘RX102 Blue 6263’ (blue coloured) was added to the approval. Rotationally moulded polyethylene materials. For use with water up to 70°C
‘Dowlex 2629UE & Dowlex 2629.10UE’. ‘RX 101 Natural, RX 101 Black 9003 & RX 101 GR Black 9003’. Natural (appears white coloured) and black coloured, rotationally moulded polyethylene materials. For use with water up to 70°C.
‘Dowlex XZ89342.00 & Dowlex XZ89342.10’. ‘RX 137 Natural, RX 137GR black 9003 & RX 137 black 9003’. Natural (appears white coloured) and black coloured, rotationally moulded polyethylene materials. For use with water up to 70°C.
‘Sabic R50035EE’. ‘RX 806 Natural, RX 806 Black 9003, RX 806GR Black 9003, RX 820 Light Blue 6001 & RX 820GR Light Blue 6001’. Natural (appears white coloured), black and light blue coloured, rotationally moulded polyethylene materials. For use with water up to 70°C.
‘Borsafe HE3494-LS-HP’. Blue coloured HDPE material for injection moulding and extrusion. ‘Borsafe HE3490-LS-HP & Borsafe HE3490-LS-HW’. Black coloured, HDPE materials for injection moulding and extrusion. ‘Borsafe HE3490-IM-W’. Black coloured, HDPE material for injection moulding. ‘Borsafe HE3490-SLS-H’. Black coloured, HDPE material for extrusion. All grades are for use with water up to 60°C.
'BorSafe HE3490-LSH'. Black coloured, extruded polyethylene material. For use with water up to 60°C.
`Icorene 3560 Black 9001`. Black coloured, LLDPE material manufactured by rotomoulding. For use with water up to 85°C.
‘4TECH 9S22110 W-A ANL, 4TECH 9S22120 W-A ANL & 4TECH 9S22130 W-A ANL’: Yellow/brown coloured, injection moulded, glass filled PPO/HIPS materials. For use with water up to 85°C.
‘Lubricomp OFL36A-BK1B639 & Thermocomp OF008A-BK1B636’. Black coloured, injection moulded polyphenylene sulphide materials. For use with water up to 85°C.
'GDE 7133', black coloured, compression moulded EPDM 'O' ring with a tested in-radius size of 2.0mm. In March 2025, ‘KD S-Ring’. black coloured, compression moulded EPDM seal with a tested in-radius size of 0.95mm was added to the approval. Both components have a shore hardness 70 and are for use with water up to 85°C.
'7EP1197 Gasket'. Black coloured, extruded EPDM gasket. Shore hardness 70. Tested in-radius size 0.5mm. '7EP1197 'O'-rings' were added to the approval in March 2023. Black coloured, injection moulded EPDM 'O'-rings. Shore hardness 70. Tested in-radius size 0.9mm. For use with water up to 85°C.
'EP 856 gaskets and 'O'-rings'. Black coloured, injection moulded 'O'-rings with a tested in-radius size of 0.9mm. Black coloured, extruded gaskets with a tested in-radius size of 0.5mm. Both gaskets and 'O'-rings have a shore hardness of 80 and are for use with water up to 85°C.
Page 28 of 83
We use cookies to give you the best possible experience with WRAS. Some are essential to provide website functions and ensure the website is secure. We also use cookies to help us understand how people use the site and to make improvements. Click "Accept All" to enable recommended settings or click "Manage cookies" to adjust your settings. For more details, see our Cookie Policy.
