Range of electrolytic scale inhibitors incorporating copper bodies. For use with copper pipe complying with BS EN 1057. Maximum working pressure 10.0 bar. Maximum operating temperature 40°C.
'Dicoat Medium Temp Black'. Factory applied, black coloured bitumen coating. Apply as per manufacturer's user instructions reference 'SPL/RD/UI/2019100121', issue no. '01' dated 08.07.2020. Cure for 7 days@30°C. Between 1st January 2021 to 22nd November 2021, the material is for use with water up to 50°C. Between 23rd November 2021 and 31st January 2026, the material is for use with water up to 60°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Sealcoat Black'. Black coloured, factory applied petroleum bituminous coating. Apply as per manufacturer's instructions for use reference 'PC 819' dated March, 26, 2021. Cure for 18 hours at 30°C. For use with water up to 23°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval. Petroleum or asphaltic bitumen, NOT coal tar bitumen. Materials listed in this section are not approved for use for contact with water that is required to be wholesome on large water retaining structures such as lining of pipes, cisterns or water storage tanks.
'Jotapipe IL6001 50S'. Factory applied, blue coloured, fusion bonded epoxy coating. Apply as per technical data sheet dated '10 September 2019'. Cure for 15 minutes@230°C. For use with water up to 85°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Eurokote® 46-60 Red Brown'. Factory applied, red-brown coloured epoxy coating. Apply as per manufacturer's technical data sheet dated 19/11/2019. Cure for 7 days@20°C. For use with water up to 60°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'High Build Solvent Free Epoxy Coating Red'. Factory applied, red coloured epoxy coating. Apply as per manufacturer's user instructions reference 'SPL/RD/UI/202006119', issue no, '01' dated 20.08.2020. Cure for 24 hours@30°C. For use with water up to 50°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'EP01'. Factory applied, blue coloured epoxy powder coating. Apply and cure as per manufacturer's instructions 'V6.3' issued March 2019. For use with water up to 65°C.
'HSL-0588-3 Silicon Coating'. Factory applied, translucent silicon coating. Apply and cure as per manufacturer's instructions version 'BLT19.05 A'. For use with water up to 85°C.
'JH'. Factory applied, blue coloured epoxy powder coating. Heat substrate to 220°C for 30 minutes, spray apply coating and then cure at 190°C for 20 minutes. For use with water up to 23°C. This material is only approved for the application and curing conditions that appear on the approval. If the cure and/or application conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'DELTAPrime 2K SF Primer and DELTAShield HP 500 PW Coating'. Factory applied, grey coloured (once mixed), two-component primer (non-water contact primer) and two-component coating (water contact coating). Mix and apply DELTAPrime 2K SF Primer as per Product Data Sheet ‘October 2019-001’. Cure for 2 hours@25°C. Then mix and apply DELTAShield HP 500 PW Coating as per Product Data Sheet ‘190625’. Cure for 1 minute@25°C. For use with water up to 85°C.
'GP HBSL EPOXY'. Factory applied, brown coloured epoxy coating. Mix and apply as per manufacturer's standard operating procedure document number 'GP/SOP/HBSL/001', version '01' dated 1st April 2019. Cure for 17 days@30°C. For use with water up to 23°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'EPX-111'. Blue coloured, factory applied epoxy powder coating. Apply and cure as per manufacturer's instructions XL-R-019-R1 dated 2015-11-12'. For use with water up to 23°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified then the material is not covered by the scope of the approval.
'EPX-213H Grey'. Factory applied, grey coloured, epoxy powder coating. Apply and cure as per manufacturer's instructions 'XL-R-019-R2' dated '2015-11-12'. For use with water up to 85°C.
'ENDOPRENE®84-30 THIXO'. Factory applied, cream coloured two-part polyurethane coating consisting of a resin and hardener. Mix and apply as per manufacturer`s technical data sheet (version dated 16/12/2019). Cure for 48 hours at 20°C. For use with water up to 55°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'MES Precast Tank Concrete Mix'. Factory made, grey coloured concrete & additive. Mix ingredients in the following percentages: Cement 19.10 %, Water 7.56 %, Coarse Aggregate 38.76 %, Fine Aggregate 34.46 %, Plastiment 186 0.03 % & ViscoCrete 0.12 %. Cure for 7 days@10°C. For use with water up to 23°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'TECHNYL ® SAFE A 219WFC V30 BK’ (black coloured) & ‘TECHNYL ® SAFE A 219WFC V30 NC’ (natural, appears off-white). Injection moulded, glass fibre reinforced polyamide 6.6 materials. For use with water up to 85°C.
‘TECHNYL ® SAFE D 219WFC V30 BK’ & ‘TECHNYL ® SAFE D 219WFC V50 BK’. Black coloured, injection moulded, glass fibre reinforced polyamide 6.10 materials. For use with water up to 85°C.
AKROMID® A3 GF 25 8 HU natural (8120) AKROMID® A3 GF 30 8 HU natural (8102) AKROMID® A3 GF 33 8 HU natural (8128) AKROMID® A3 GF 35 8 HU natural (8121) AKROMID® A3 GF 40 8 HU natural (8122) AKROMID® A3 GF 43 8 HU natural (8130) AKROMID® A3 GF 45 8 HU natural (8123) AKROMID® A3 GF 50 8 HU natural (8124) AKROMID® A3 GF 55 8 HU natural (8125) AKROMID® A3 GF 60 8 HU natural (8126) AKROMID® A3 GF 25 8 HU black (8118) AKROMID® A3 GF 30 8 HU black (8112) AKROMID® A3 GF 33 8 HU black (8129) AKROMID® A3 GF 35 8 HU black (8113) AKROMID® A3 GF 40 8 HU black (8114) AKROMID® A3 GF 43 8 HU black (8131) AKROMID® A3 GF 45 8 HU black (8115) AKROMID® A3 GF 50 8 HU black (8116) AKROMID® A3 GF 55 8 HU black (8119) AKROMID® A3 GF 60 8 HU black (8117) Natural (appears white) and black coloured, injection moulded, glass fibre reinforced PA66 materials. For use with water up to 85°C.
‘5052911193 (50A), 5062911233 (60A), 5072911255 (70A), 5082911184 (80A) and 5092911126 (90A)’. Black coloured, compression moulded EPDM materials. Shore hardness between 50A & 90A. Tested in-radius size 1.0mm. For use with water up to 23°C.
'1922, 1923 & 1933 washers'. Red coloured, injection moulded silicone rubber washers. 1923 washers have an in-radius of 1.59mm. 1933 washers have an in-radius of 0.83mm. 1922 washers have an in-radius of 1.23mm. For use with water up to 85°C.
'Flomasta 7619J'. Off-white coloured, PTFE paste intended for use as a thread sealant. For use with water up to 23°C.
'Uneplas Gel Solvent Cement'. Clear, transparent (un-pigmented) solvent cement, (intended to join PVC pipe and fittings). Apply as per manufacturer's instructions review date '2019-09-11'. Cure for 20 days at 7°C. For use with water up to 65°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
Range of single hole, single outlet (fixed) electronically controlled tap assemblies (either stainless steel or brass bodies in a variety of finishes). Flow is controlled via two solenoid valves (housed in a control box) activated via an infra-red sensor, the inlets to the control box incorporate stainless steel strainers. The temperature is controlled independently via a ceramic cartridge with a dome type operating member. The spout outlet incorporates a plastic aerator. Maximum working pressure 5.0 bar. Maximum operating temperature 60°C.
Range of single hole, single outlet (fixed) electronically operated, tap assemblies (chromium plated brass). Flow is controlled via solenoid valve and actuated by a touch sensor. The spout outlets incorporate a plastic aerator, supplied with stainless steel strainers. Maximum working pressure 8.0 bar. Maximum operating temperature 60°C.
Range of single hole, single outlet (swivel) combination tap assemblies (various finishes) with a pull-out spray mechanism. Flow is controlled via a ceramic cartridge headwork with a single lever operating member incorporating an infra-red sensor on the swivel arm which operates a solenoid valve. The spout outlet incorporates a plastic aerator and a hand spray mechanism, and the product is supplied with metal backnuts. Maximum working pressure 5.0 Bar. Maximum operating temperature 60°C.
Range of deck mounted, electronically operated combination tap assemblies (chromium plated brass). The flow is controlled by a solenoid valve which is actuated via an infrared sensor on the spout. The spout outlet incorporates a plastic aerator. Maximum working pressure 8.0 bar. Maximum operating temperature 60°C.
Range of float operated valves with brass bodies manufactured to BS1212 Part 2 1990. The valves have ½’’ BSP inlets with plastic backnuts, brass or plastic back plates, an up and over type outlet discharge and a brass lever arm. Maximum working pressure 14.0 bar. For use with cold water only.
Range of float operated valves with plastic bodies and either brass or plastic inlet tails of the side or bottom entry type manufactured to BS1212 Part 3 1990. The valves have ½’’ BSP inlets with plastic backnuts, an up and over type outlet discharge and a plastic operating lever adjusted by a screw & lock nut. Maximum working pressure 14.0 bar. For cold water use only.
Range of BS1212 Part 3 1990 float operated valves incorporating plastic bodies of either the side or bottom entry type. Maximum working pressure 14.0 bar. For cold water use only.
Range of non-verifiable double check valve assemblies (DZR brass bodies) incorporating spherical valves and either red or blue butterfly handles. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.
Range of Caprice assisted baths which include a choice of with or without a hoist. Flow is controlled via a thermostatic mixing valve supplying the bath spout outlet or shower handset. The discharge from the bath spout and shower handset in via a type AUK 3 airgap, verified by measurement, suitable for Fluid Category 5 backflow protection Maximum working pressure 6.0 bar.
Non-metallic materials and components comply with BS6920 at 46°C
Quarter turn ceramic disc headwork incorporating a plastic body to be housed in specifically dimensioned bodies. Maximum working pressure 10.0 bar. Maximum operating temperature 90°C.
Range of single hole, single outlet (fixed) combination tap assemblies (chromium plated brass) incorporating a ceramic cartridge headwork with a single lever operating member. The spout outlet incorporates a plastic aerator. Products are supplied with a pop-up waste. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.
Range of single hole, single outlet (fixed) combination tap assemblies with brass bodies (various finishes), incorporating a ceramic cartridge headwork with a single lever operating member. The spout outlet incorporates a plastic aerator. Some products are supplied with a pop-up waste or a click type waste (see model). Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.
Range of single hole, single outlet (fixed) combination tap assemblies (various finishes) incorporating a ceramic cartridge headwork with a single lever operating member. The spout outlet incorporates a plastic aerator. The 36 100 xxx model is supplied with a lever operated pop-up waste. Maximum working pressure 10.0 Bar. Maximum operating temperature 60°C.
Range of single hole, single outlet (fixed) combination tap assemblies incorporating brass bodies (various finishes), ceramic cartridge headworks with single lever operating members. The spout outlets incorporates a plastic aerator. Models 100121306, 100121305 & 100123629 are supplied with lever operated pop-up waste. Maximum working pressure 5.0 bar. Maximum operating temperature 60°C.
Range of single hole, single outlet (fixed) combination tap assemblies incorporating brass bodies (chrome plated) ceramic cartridge headwork and single lever operating member. The spout outlet incorporates a plastic aerator. Maximum working pressure 10.0 Bar. Maximum operating temperature 60°C.
Range of deck mounted, single hole, single outlet (fixed) electronically controlled combination tap assemblies with stainless steel bodies (in various finishes). The flow is controlled by a solenoid valve activated via an infra-red sensor. The solenoid housing attaches to the main tap body via (black) LLDPE tubing. The spout outlets incorporate a plastic aerator. Maximum working pressure 6.0 bar. Maximum operating temperature 60°C
Single hole, single outlet (swivel) combination tap assembly (chromium plated brass), incorporating quarter turn ceramic disk headworks with single leaver operating members. The spout outlet incorporates a plastic aerator. Maximum working pressure 5.0 bar. Maximum operating temperature 60°C.
Range of single hole, metal, single outlet (swivel) combination tap assemblies (chromium plated brass), incorporating a ceramic cartridge headwork with a single lever operating member. The spout outlets incorporate plastic aerators. The 31 609 xxx model is supplied with a pop-up waste. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.
Range of wall mounted, two hole, single outlet (fixed) combination tap assemblies (chromium plated brass) incorporating a ceramic cartridge headworks with a single lever operating member. The spout outlets are a waterfall type incorporating a stainless-steel strainer. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.
Range of two hole, single outlet, (fixed) combination tap assemblies (chromium plated brass), Models 49723, 26684 & 18193 incorporate a non rising spindle headwork with dome type operating members. The spout outlets incorporate a plastic flow straightener and the products are supplied with metal backnuts. . Maximum working pressure 10.0 bar. Maximum operating temperature 85°C.
Range of two-hole, single outlet (fixed) combination tap assemblies (brass bodies, various finishes - see model) incorporating quarter turn ceramic disc headworks with single lever operating members. The spout outlet incorporates a plastic flow straightener (TR1027 and TR1005 models) or a plastic aerator (all other models). The product is supplied with metal back nuts. Maximum working pressure 10.0 bar. Maximum operating temperature 65°C.
Two hole, single outlet, fixed combination tap assembly (chromium plated brass) incorporating quarter turn ceramic disc headworks with single lever operating members and a manual diverter to shower outlet. The spout outlet incorporates a plastic flow straightener. The product is supplied with a shower hose, shower handset and metal backnuts, Maximum working pressure 5.0 bar. Maximum operating temperature 60°C.
Range of wall mounted two-hole, metal, single outlet (fixed) combination tap assemblies (chromium plated brass), incorporating a ceramic disc diverter headwork controlling the flow between the spout outlet and the shower outlet with a dome type operating member. Temperature is controlled independently via a thermostatic cartridge with dome type operating members that incorporates a manual override button. The spout outlet incorporates a plastic aerator. Each inlet incorporates a stainless-steel strainer and an approved check valve cartridge, however, the complete product has not been fully tested to demonstrate it provides backflow protection. Maximum working pressure 10.0 Bar Maximum operating temperature 60°C
Range of floor mounted, two-hole, single outlet (swivel) combination tap assemblies (stainless steel and brass bodies various finishes), incorporating a ceramic cartridge headwork with a single lever operating member. The spout outlet incorporates a plastic aerator. Maximum working pressure 5.0 Bar Maximum operating temperature 70.0°C
Range of two-hole, single outlet (swivel) combination tap assemblies (various finishes, see models). Incorporating ceramic cartridge headworks and single operating members. The spout outlet incorporates a plastic aerator. Maximum working pressure 10.0 bar. Maximum operating temperature 65°C
Range of three hole, single outlet (fixed) combination tap assemblies (brass bodies with various finishes). Incorporating quarter turn ceramic disc and various operating members. The spout outlet incorporates a plastic aerator (except Broadway and Niagara spout options). The product is supplied with nylon braided EPDM lined flexible hose assemblies incorporating ½” captive nut end connections on both ends or at one end and M10 at the other. The hoses are intended to connect between the side body headworks and the spout junction. The spout junction of the Malmaison and Niagara spout options incorporates a plastic flow regulator. The product is also supplied with either a click type or pop-up waste (see model), and a ½” BSP (F) nut and NBR washer to adapt the side valve inlet connections. Maximum working pressure 3.5 bar. Maximum operating temperature 60°C.
Range of three hole, single outlet (fixed) combination tap assemblies (brass bodies with various finishes). Incorporating quarter turn ceramic disc and various operating members. The spout outlet incorporates a plastic aerator. The product is supplied with nylon braided EPDM lined flexible hose assemblies incorporating ½” captive nut end connections on both ends or at one end and M10 at the other. The hoses are intended to connect between the side body headworks and the spout junction. The product is also supplied with a pop-up waste, and a ½” BSP (F) nut and NBR washer to adapt the side valve inlet connections. Maximum working pressure 3.5 bar. Maximum operating temperature 60°C.
Range of three hole, single outlet (fixed) combination tap assemblies with brass bodies (various finishes - see model), incorporating quarter turn ceramic disc headworks with various operating members (see models). The products are supplied with two stainless steel braided EPDM lined flexible hose assemblies with ½” captive nut end connections for installation between the side valves and the spout. The spout outlet incorporates a plastic aerator. Maximum working pressure 3.0 bar. Maximum operating temperature 60°C.
Page 3 of 18
We use cookies to give you the best possible experience with WRAS. Some are essential to provide website functions and ensure the website is secure. We also use cookies to help us understand how people use the site and to make improvements. Click "Accept All" to enable recommended settings or click "Manage cookies" to adjust your settings. For more details, see our Cookie Policy.
