'HYDRO MULTI-E' booster set range consisting of two to four electronically controlled pumps connected in parallel and mounted on a common base frame provided with all necessary fittings. The suction manifold incorporates an isolation valve fitted between it and the individual pumps, and a pressure switch with an isolation valve. The discharge manifold incorporates an isolation valve and a non-return valve (not suitable for backflow protection), which is fitted between it and the individual pumps, it also incorporates a combined isolation and drain valve. Maximum working pressure 16.0 bar. Cold water use only.

Section:

1610 Pumps

Section Subtitle:

Wholesome water use.

WRAS Approval Number:

250107701

Basis of Compliance:

Tested to regulators Specification Test Code Sheets

Size:

2” or 2½” BSPT (M). DN80 or DN100 flanged.

Marking:

Grundfos and Grundfos logo on pumps. Grundfos and Grundfos logo, type, Model, P/N no., Serial no., technical info, manufacturing country on adhesive label on pump base plate.

Installation Requirements:

R001 R415 R511

Expiry date:

31/01/2030

Model:

2” or 2½” BSPT (M): HYDRO MULTI-E “X” CRIE1-* x1 x2-x3-x4-x5-x6. HYDRO MULTI-E “X” CRIE3-* x1 x2-x3-x4-x5-x6. HYDRO MULTI-E “X” CRIE5-* x1 x2-x3-x4-x5-x6. 2½” BSPT (M) or DN80 flanged. HYDRO MULTI-E “X” CRIE10-* x1 x2-x3-x4-x5-x6. DN80 or DN100 flanged. HYDRO MULTI-E “X” CRIE15-* x1 x2-x3-x4-x5-x6. HYDRO MULTI-E “X” CRIE20-* x1 x2-x3-x4-x5-x6. The “X” preceding CR indicates the number of pumps in the booster set, between 2 and 4 pumps. CRIE1, CRIE3 and CRIE5 pumps: • Systems with 2 to 3 pumps = 2” threaded. • Systems with 4 pumps = 2½” threaded. CRIE10 pumps: • Systems with 2 pumps = 2½” threaded. • Systems with 3 to 4 pumps = DN80 flanges. CRIE15 and CRIE20 pumps: • Systems with 2 pumps = DN80 flanges. • Systems with 3 to 4 pumps = DN100 flanges. The number following the pump type designation (1, 3, 5, 10, 15 and 20) indicates the flow rate of the pump in m3/h. * The pumps are available with 1 to 36 impellers/stages (e.g. CRIE5-12 = 12 stages). x1 = U1, U2 or U8 relates to supply voltage (of no importance for drinking water). x2 = Design: A, B or C (of no importance for drinking water). x3 = Staring method: A (of no importance for drinking water). x4 = Product (country) range: A: International range. x5 = Material combination: A: Stainless steel manifold and base frame and standard valves. x6 = Options: A: Standard hydraulic.

Product Images

Approval Holder:

Grundfos Holding A/S

Company Name

Grundfos Holding A/S

Address

Poul Due Jensens Vej 7 Bjerringbro

Postcode

DK-8850

Country

Denmark

Phone

+36302482216

General Email

oszilagyi@grundfos.com

View All Listings by this Company

Dutypoint ‘VMV’ range of cold water supply booster sets, incorporating 2 to 8 pumps with a modular stainless steel manifold system. VMV2, VMV3 and VMV4 pump sets are available with DN80 to DN150 manifolds depending on application. VMV5, VMV6, VMV7 and VMV8 pump sets are available with DN150 to DN200 manifolds, depending on application. The products incorporate spherical valves on both the suction and discharge manifolds, with expansion vessels, isolation valves, pressure gauges and transducers on the discharge manifolds only. Maximum working pressure 16.0 bar. Cold water use only.

Section:

1610 Pumps

Section Subtitle:

Wholesome water use.

WRAS Approval Number:

241204714

Basis of Compliance:

Tested to regulators Specification Test Code Sheets

Size:

DN80 – DN200 Flanged connection

Marking:

Duty point, model and pressure on data label.

Installation Requirements:

R001 R415

Expiry date:

31/12/2029

Model:

VMV DN80 Versions twin, triple and quadruple pump units: VMV2-05, VMV2-07 and VMV2-10 – All motor sizes VMV3-05, VMV3-07 and VMV3-10 – All motor sizes VMV4-05, VMV4-07 and VMV4-10 – All motor sizes DN100 Versions: Twin, Triple and Quadruple Pump Units: VMV2-05, VMV2-07 and VMV2-10 – All motor sizes VMV3-05, VMV3-07 and VMV3-10 – All motor sizes VMV4-05, VMV4-07 and VMV4-10 – All motor sizes DN150 Versions: Twin, Triple and Quadruple Pump Units: VMV2-05, VMV2-20 and VMV2-25 – All motor sizes VMV3-05, VMV3-20 and VMV3-25 – All motor sizes VMV4-05, VMV4-20 and VMV4-25 – All motor sizes Units incorporating from 5 to 8 pumps (Models VMV5, VMV6, VMV7, VMV8): All units will feature DN150 – DN200 manifolds, size dependent on application. Key to Model Numbers: Example of Model Number: VMV2-15-V110 Range: VMV Number of pumps: 2 Nominal Flow rate (l/sec): 15 Inverter type e.g. ‘V’ for Vasco, or ‘H’ for Hydrovar Motor size (kW x 10)

Product Images

Approval Holder:

Dutypoint Ltd.

Company Name

Dutypoint Ltd.

Address

Unit A, Quedgeley West Business Park, Hardwicke, Gloucester

Postcode

GL2 4PA

Country

United Kingdom

Phone

01452313334

General Email

austin.hill@dutypoint.com

View All Listings by this Company

Range of horizontal multistage pumps with stainless steel bodies, diffuser and impellers and EPDM ‘O’-rings. The products incorporate a graphite-SiC-EPDM shaft seal. The products incorporate a drain plug. Maximum working pressure 8.5 bar. 9Maximum operating temperature 80°C.

Section:

1610 Pumps

Section Subtitle:

Wholesome water use.

WRAS Approval Number:

241002722

Basis of Compliance:

Tested to regulators Specification Test Code Sheets

Note:

The discharge from the drain plug must be via a type `AA`, `AB` or `AD` airgap, or in accordance with EN1717.

Size:

P 3S & U 5S models: 1” BSP (F) inlet x 1” BSP (F) outlet. P 7S models: 1¼” BSP (F) inlet x 1” BSP (F) outlet. P 9S models: 1½” BSP (F) inlet x 1¼” BSP (F) outlet. P 18S models: 2” BSP (F) inlet x 1½” BSP (F) outlet.

Marking:

Foras (Brand of Pentax), model code and other technical information on data plate on body.

Installation Requirements:

R001 R415

Expiry date:

31/10/2029

Model:

P range: P X(S) - XX/Y (T) Where: P = pump model X = Nominal flow-rate m³/h (3, 5, 7, 9, 18 see model list), S = ULTRA S range - stainless steel hydraulic part, XX = nominal power HPx100 (50 - 400 see model list), Y = Number of impellers (2 - 7 see model list), T = 3 phase, [blank] = single phase. P 3S models: P 3S-50/2; P 3S-70/3; P 3S-90/4; P 3S-100/5; P 3S-120/6; P 3S-150/7. P 5S models: P 5S-70/2; P 5S-80/3; P 5S-120/4; P 5S-150/5; P 5S-180/6; P 5S-200/7. P 7S models: P 7S-100/2; P 7S-120/3; P 7S-180/4; P 7S-250/5; P 7S-300/6. P 9S models: P 9S-100/2; P 9S-150/3; P 9S-200/4; P 9S-250/5. P 3S models: P 3S-50/2 T; P 3S-70/3 T; P 3S-90/4 T; P 3S-100/5 T; P 3S-120/6 T; P 3S-150/7 T. P 5S models: P 5S-70/2 T; P 5S-80/3 T; P 5S-120/4 T; P 5S-150/5 T; P 5S-180/6 T; P 5S-200/7 T. P 7S models: P 7S-100/2 T; P 7S-120/3 T; P 7S-180/4 T; P 7S-250/5 T; P 7S-300/6 T; P 7S-350/7 T. P 9S models: P 9S-100/2 T; P 9S-150/3 T; P 9S-200/4 T; P 9S-250/5 T. P 18S models: P 18S-180/2 T; P 18S-250/3 T; P 18S-400/4 T.

Approval Holder:

PENTAX INDUSTRIES SpA

Company Name

PENTAX INDUSTRIES SpA

Address

Viale dell’Industria 1 Veronella

Postcode

37040

Country

Italy

Phone

+39 0442 489567

General Email

g.cengia@pentax-pumps.it

View All Listings by this Company

Range of booster pumps with stainless steel bodies, impellers and non-return valves (not suitable for backflow protection) at the inlets. From June 2025 the pumps are available with plastic or stainless steel impellers. Maximum working pressure 6.0 bar. Cold water use only.

Section:

1610 Pumps

Section Subtitle:

Wholesome water use.

WRAS Approval Number:

250102716

Basis of Compliance:

Tested to regulators Specification Test Code Sheets

Size:

1” BSP (M).

Marking:

Pedrollo Spa logo on front panel. Model and product information on adhesive label.

Installation Requirements:

R001 R008 R415

Expiry date:

31/01/2030

Model:

DG-BLU 3, DG PED 3 EVO, DG-BLU 5, DG PED 5 EVO, DUAL DG-BLU 3+3, DUAL DG PED EVO 3+3, DUAL DG-BLU 3+5, DUAL DG PED EVO 3+5, DUAL DG-BLU 5+5, DUAL DG PED EVO 5+5.

Product Images

Manufacturer:

Pedrollo S.p.A.

Company Name

Pedrollo S.p.A.

Address

via Enrico Fermi, 7 37047 San Bonifacio (VR)

Country

Italy

Phone

+39 045 6136311

View All Listings by this Company

“TP/TPE series 100” single stage centrifugal pumps, incorporating cast iron (with black coloured electrocoating) or stainless-steel bodies and plastic impellers. Maximum working pressure: Cast iron models: 16.0 bar, Stainless steel models: 10.0 bar. Maximum operating temperature: Cast iron models: 60°C, Stainless steel models: 85°C.

Section:

1610 Pumps

Section Subtitle:

Wholesome water use.

WRAS Approval Number:

250307701

Basis of Compliance:

Tested to regulators Specification Test Code Sheets

Size:

1½”-2” BSP (M) inlet/outlet. DN40 Flanged inlet/outlet.

Marking:

Grundfos and Grundfos logo, type, model, product no., technical info and manufacturing country on data plate. Grundfos and Grundfos logo on motor. Flow arrow on body.

Installation Requirements:

R001 R415

Expiry date:

31/03/2030

Model:

TP(E)100 series: TP (E) XX-XXX/2 A or AI or X - F or O - A or I - XXXX Where: TP = pump type with normal Asynchronous motor. TPE = pump type with E-motor (motor with integrated frequency driver). XX = nominal DN size of inlet/outlet ports (25 - 40). XXX = maximum head (dm) (50 - 90). /2 = pole number. A or AI or X = A: Basic version, AI: PN6 flange, X: Special Version. F or O = F: DIN Flanged, O: Union (threaded). A or I = A: Basic Version. Cast iron pump housing and motor stool, I: S/Steel pump housing and motor stool. XXXX = shaft seal type - BQQE or BQBE. YYY = coding for motor. E.g. TP (E) 32-60/2 A-F-A-BQQE-CX1

Product Images

Approval Holder:

Grundfos Holding A/S

Company Name

Grundfos Holding A/S

Address

Poul Due Jensens Vej 7 Bjerringbro

Postcode

DK-8850

Country

Denmark

Phone

+36302482216

General Email

oszilagyi@grundfos.com

View All Listings by this Company

“TPE 2 & TPE3 series” single stage centrifugal pumps, incorporating cast iron (with black coloured electrocoating) or stainless-steel bodies and plastic impellers. Maximum working pressure 10.0 bar. Maximum operating temperature: Cast iron models: 60°C, Stainless steel models: 85°C.

Section:

1610 Pumps

Section Subtitle:

Wholesome water use.

WRAS Approval Number:

250307702

Basis of Compliance:

Tested to regulators Specification Test Code Sheets

Size:

Cast iron models: DN32 - DN100 Flanged inlet/outlet. Stainless steel models: DN32 - DN65 Flanged inlet/outlet.

Marking:

Grundfos and Grundfos logo, type, model, product no., technical info and manufacturing country on data plate. Grundfos and Grundfos logo on control unit.

Installation Requirements:

R001 R415

Expiry date:

31/03/2030

Model:

TPE2/3 series: TPE 2 or 3 (E) XX-XXX S or N - A or AI or X - F - A or I - XXXX - YYY Where: TPE2 = pump type with normal Asynchronous motor. TPE3 = pump type with E-motor (motor with integrated frequency driver). XX = nominal DN size of inlet/outlet ports (cast iron 32 - 100, S/Steel 32 - 65). XXX = maximum head (dm). S or N = S: Built-in differential-pressure and temperature sensor (TPE3 models), N: Without built-in sensor (TPE2 models). A or AI or X = A: Basic version, AI: PN6 flange, X: Special Version. F = DIN Flanged. A or I = A: Basic Version. Cast iron pump housing and motor stool, I: S/Steel pump housing and motor stool. XXXX = shaft seal type - BQQE or BQBE. YYY = coding for motor. E.g. TPE3 100-120 S-X-F-A-BQQE-GAB

Product Images

Approval Holder:

Grundfos Holding A/S

Company Name

Grundfos Holding A/S

Address

Poul Due Jensens Vej 7 Bjerringbro

Postcode

DK-8850

Country

Denmark

Phone

+36302482216

General Email

oszilagyi@grundfos.com

View All Listings by this Company

Range of multi-stage semiaxial submersible pumps with stainless steel bodies and impellers. Please note, this approval does not cover the motor, motor connection kit or power cable necessary for the pump to operate. Open outlet use only. Cold water use only.

Section:

1610 Pumps

Section Subtitle:

Wholesome water use.

WRAS Approval Number:

250504706

Basis of Compliance:

Tested to regulators Specification Test Code Sheets

Size:

140 SX models: 3” GAS FLANGED outlet conenection, 180 SX models: 5” GAS FLANGED outlet conenection, 230 SX models: 6” GAS FLANGED outlet conenection, 270 SX models: DN200 FLANGED outlet conenection.

Marking:

Panelli logo, model type, serial no., made in Italy, production date (MM/YY) and other techical info on data plate on body.

Installation Requirements:

R001 R415

Expiry date:

31/05/2030

Proviso:

Open outlet use only.

Model:

140 SX 34/XX, 140 SX 44/XX, 140 SX 54/XX, 140 SX 64/XX, 180 SX 102/ XX, 180 SX 124/XX, 180 SX 140/XX, 180 SX 78/XX, 180 SX 90/XX, 230 SX 200/XX (DRXX), 230 SX 220/XX (DRXX), 230 SX 240/XX (DRXX), 230 SX 280/XX (DRXX), 270 SX 370/XX (DRXX), 270 SX 440/XX (DRXX) (A). Where: 140-180-230-270 = pump diameter. 140: 6”, 180: 8”, 230: 10”, 270: 12”. SX: Semi-axial pump family. 34-440: Flow. /XX = Number of stages (XX will be replaced by 1 or 2 digits as follows). 140 SX 34: 3 to 27, 140 SX 44: 3 to 22, 140 SX 54: 3 to 22, 140 SX 64: 1 to 18, 180 SX 102: 1 to 15, 180 SX 124: 1 to 13, 180 SX 140: 1 to 12, 180 SX 78: 1 to 19, 180 SX 90: 1 to 17, 230 SX 200: 1 to 9, 230 SX 220: 1 to 7, 230 SX 240: 1 to 7, 230 SX 280: 1 to 7, 270 SX 370: 1 to 5, 270 SX 440: 1 to 5. Optional: DRXX = Impeller diameter reduction in mm. XX can either be 10 or 20. A = Impeller with corner reduction.

Approval Holder:

Panelli S.r.l.

Company Name

Panelli S.r.l.

Address

Via Rana 63/65 Z.I D5 Spinetta Marengo

View All Listings by this Company

Manufacturer:

Panelli S.r.l.

Company Name

Panelli S.r.l.

Address

Via Rana 63/65 Z.I D5 Spinetta Marengo

View All Listings by this Company

Section:

1650 Shower Outlets

Description:

A Range of Shower head(s) and/or shower handset(s).

Conditions of use Type 1 Overhead shower

Basis of Compliance:

Tested to a standard assessed as an appropriate British Standard by WRAS

Installation Requirements:

R001 R040

Expiry date:

31/05/2030

Notes & Further Information

XXX Denotes the following: First, second & third XXX for different finishes: Chrome – No suffix, Brushed brass – BGP, PVD Gold – PVD, Brushed Nickel – BN1, Gun Metal – GMG, Stainless Steel – SS1, Black Chrome – BCP, Titanium – TIB and Antique Bronze – AB1.

Product Images

Approval Holder:

PPI Xiamen Industry Co., Ltd.

Company Name

PPI Xiamen Industry Co., Ltd.

Address

No 88 South Houxiang Road Xinyang Industrial Zone Haicang District Xiamen

Postcode

361022

Country

China

General Email

heatheryang@xmppi.com

View All Listings by this Company

Manufacturers:

PPI XIAMEN INDUSTRY CO LTD

Section:

1650 Shower Outlets

Description:

A Shower head(s) and/or shower handset(s).

Wall Mounted Shower head

Basis of Compliance:

Tested to regulators Specification Test Code Sheets

Installation Requirements:

R001 R040

Expiry date:

30/04/2030

Product Images

Approval Holder:

Bristan Group Ltd.

Company Name

Bristan Group Ltd.

Address

Birch Coppice Business Park Dorden Tamworth

Postcode

B78 1SG

Country

Staffs

Phone

01827 254144

General Email

hmistry@bristan.com

View All Listings by this Company

Range of in-line Y patterned strainers with bronze bodies and a stainless-steel mesh strainer. Maximum working pressure 20.0 bar. Maximum operating temperature 85°C.

Section:

1715 Strainers

Basis of Compliance:

Tested to regulators Specification Test Code Sheets

Size:

Size: ½” to 2” BSPT (F), NPT (F) or BSPP (F)

Marking:

IVAL logo, size, PN, DN and flow arrow body

Installation Requirements:

R001 R120

Expiry date:

30/04/2030

Model:

S40

Approval Holder:

IVAL Hydronics UK Ltd

Company Name

IVAL Hydronics UK Ltd

Address

71-75 Shelton Street, Covent Garden, London.

Postcode

WC2H 9JQ

Country

United Kingdom

General Email

info@ival-hydronics.co.uk

View All Listings by this Company

Section:

1750 Taps

Description:

A Range of Draw off bib tap(s)

Wall Mounted

Basis of Compliance:

Tested to regulators Specification Test Code Sheets

Installation Requirements:

R001 R040

Expiry date:

30/04/2030

Product Images

Approval Holder:

Bristan Group Ltd.

Company Name

Bristan Group Ltd.

Address

Birch Coppice Business Park Dorden Tamworth

Postcode

B78 1SG

Country

Staffs

Phone

01827 254144

General Email

hmistry@bristan.com

View All Listings by this Company

Range of bib taps (nickel plated brass) or (DZR brass) bodies – see models, incorporating a spherical valve to control the flow. The products incorporate single lever operating members. Some models are supplied with lock shields (see models). The spout outlet incorporates a hose union spigot connection with a plastic flow straightener. Maximum working pressure 16.0 Bar. Maximum operating temperature 85°C.

Section:

1750 Taps

Section Subtitle:

Draw off bib tap(s)

WRAS Approval Number:

241102088

Basis of Compliance:

Tested to regulators Specification Test Code Sheets

Note:

All models can be supplied in BSPT, NPT or BSPP threads, and the sizes are listed with the models:

Size:

½”(DN15), ¾”(DN20) & 1”(DN25).

Marking:

Valtech & size on body. CR on DZR brass models.

Installation Requirements:

R001

Expiry date:

30/11/2029

Model:

BT01A-BR-DN15 BT01A- BR -DN20 BT01A- BR -DN25 BT01A-DR-DN15 BT01A-DR-DN20 BT01A-DR-DN25 BT08-L-DN15 BT08-L-DN20 BT08-L-DN25 BT08-LDR-DN15 BT08- LDR DN20 BT08- LDR -DN25

Approval Holder:

Ningbo Valtech Flow Control Co., Ltd

Company Name

Ningbo Valtech Flow Control Co., Ltd

Address

1130 Baizhang Road Ningbo Zhejiang

Country

China

View All Listings by this Company

Range of drain taps with brass (or DZR brass, see models) bodies and non-rising spindle headwork. Maximum working pressure 16.0 Bar Maximum operating temperature 85.0°C

Section:

1770 Taps

Section Subtitle:

Draining, for above ground use only.

WRAS Approval Number:

250302032

Basis of Compliance:

Tested to regulators Specification Test Code Sheets

Size:

See models below

Marking:

Size, D.O.M (MM:YY) BS2879-2 & Zhejiang logo on body. DZR Brass models: Size, CR, D.O.M (MM:YY) BS2879-2 & Zhejiang logo

Installation Requirements:

R001 R511

Expiry date:

31/03/2030

Model:

P1013.G15: 1/2 BSP M P1016.G15: 1/2 BSP M (DZR) P1020.G15: 1/2 BSP M P1030.015: 15MM Tail P1050.015: 15MM Tail (DZR) P1040.015: 15MM Tail

Product Images

Manufacturer:

Zhejiang Fansheng Fluid Control Co., LTD

Company Name

Zhejiang Fansheng Fluid Control Co., LTD

Address

Putian Industrial Area Chumen Area Yuhuan City Zhejiang Province

Country

China

View All Listings by this Company

Drain off cock with a DZR brass body, non-rising spindle headwork and EPDM seals and washers. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.

Section:

1770 Taps

Section Subtitle:

Draining, for above ground use only.

WRAS Approval Number:

250415016

Basis of Compliance:

Tested to regulators Specification Test Code Sheets

Size:

15mm spigot connection

Marking:

Taizhou Double Winners Copper Co., Ltd logo (dbw), size, date of manufacture (MM-YY), CR and BS 2879-2 on body.

Installation Requirements:

R001

Expiry date:

30/04/2030

Model:

6850015

Product Images

Approval Holder:

Taizhou Double Winners Copper Co., Ltd

Company Name

Taizhou Double Winners Copper Co., Ltd

Address

#2‐902, Z Center, No. 185 Wenxue Road, Jiaojiang, Taizhou, 31800, Zhejiang, China

View All Listings by this Company

Section:

1800 Taps

Description:

A Pillar tap(s).

Deck Mounted Capable of achieving AUK2 Tap Gap

Basis of Compliance:

Tested to regulators Specification Test Code Sheets

Installation Requirements:

R001 R005

Expiry date:

28/05/2030

Notes & Further Information

X XXX Denotes the following: First X: Different handle and the second, third & fourth XXX for different finishes: Handles: A (Cross top type) Chrome – No suffix, Brushed brass – BGP, PVD Gold – PVD, Brushed Nickel – BN1, Gun Metal – GMG, Matt Black – MBK, Matt White – MWH, Stainless Steel – SS1, Black Chrome – BCP, Titanium – TIB and Antique Bronze – AB1.

Product Images

Approval Holder:

PPI Xiamen Industry Co., Ltd.

Company Name

PPI Xiamen Industry Co., Ltd.

Address

No 88 South Houxiang Road Xinyang Industrial Zone Haicang District Xiamen

Postcode

361022

Country

China

General Email

heatheryang@xmppi.com

View All Listings by this Company

Manufacturers:

PPI XIAMEN INDUSTRY CO LTD

Section:

1800 Taps

Description:

A Pillar tap(s).

Deck mounted Capable of Achieving AUK2 Tap Gap

Basis of Compliance:

Tested to regulators Specification Test Code Sheets

Installation Requirements:

R001 R005

Expiry date:

31/05/2030

Notes & Further Information

X XXX Denotes the following: First X: Different handle option = and the second, third & fourth XXX for different finishes: Handles : A (Cross top type) Chrome – No suffix, Brushed brass – BGP, PVD Gold – PVD, Brushed Nickel – BN1, Gun Metal – GMG, Matt Black – MBK, Matt White – MWH, Stainless Steel – SS1, Black Chrome – BCP, Titanium – TIB and Antique Bronze – AB1.

Product Images

Approval Holder:

PPI Xiamen Industry Co., Ltd.

Company Name

PPI Xiamen Industry Co., Ltd.

Address

No 88 South Houxiang Road Xinyang Industrial Zone Haicang District Xiamen

Postcode

361022

Country

China

General Email

heatheryang@xmppi.com

View All Listings by this Company

Manufacturers:

PPI XIAMEN INDUSTRY CO LTD

Section:

1825 Showers

Description:

A Self closing shower(s)

Wall mounted shower kit with a wall mounted overhead shower

Basis of Compliance:

Tested to regulators Specification Test Code Sheets

Installation Requirements:

R001 R040

Expiry date:

30/04/2030

Product Images

Approval Holder:

Bristan Group Ltd.

Company Name

Bristan Group Ltd.

Address

Birch Coppice Business Park Dorden Tamworth

Postcode

B78 1SG

Country

Staffs

Phone

01827 254144

General Email

hmistry@bristan.com

View All Listings by this Company

Range of Single Layer PPRCT Solid Pipes (SDR7.4) comprising of green coloured PPRCT material. Not approved for use with any fittings. Maximum working pressure 23.4 bar. Cold water above ground use only.

Section:

1840 Tubes

Section Subtitle:

Plastic, cold-water use.

WRAS Approval Number:

250402708

Basis of Compliance:

Tested to regulators Specification Test Code Sheets

Size:

SEE MODEL

Marking:

Q-Therm, Size, date of manufacture (DD/MM/YY) and technical info on pipe.

Installation Requirements:

R001

Expiry date:

30/04/2030

Model:

CT17SP2001 – 20x2.8mm CT17SP2002 – 25x3.5mm CT17SP2003 – 32x4.4mm CT17SP2004 – 40x5.5mm CT17SP2005 – 50x6.9mm CT17SP2006 – 63x8.6mm CT17SP2007 – 75x10.3mm CT17SP2009 – 90x12.3mm CT17SP2010 – 110x15.1mm

Approval Holder:

Quantum Industries LLC

Company Name

Quantum Industries LLC

Address

Al Ghail Industrial Park, Ras Al Khaimah, PB 86488

Country

UAE

View All Listings by this Company

Range of stainless steel over braided, PEX lined flexible hoses, incorporating EPDM or fibre washers. Maximum working pressure: 6.0 bar. Maximum operating temperature: 65°C.

Section:

1860 Tubes

Section Subtitle:

Plastic hoses.

WRAS Approval Number:

240702080

Basis of Compliance:

Tested to regulators Specification Test Code Sheets

Size:

15mm Compression x 1/2" BSP (M)

Marking:

Qualflex, QWRAS, year of manufacture (YY) and temperature and pressure on ferrule.

Installation Requirements:

R001 R008

Expiry date:

31/07/2029

Model:

HOSE265013

Approval Holder:

RELIANCE WORLDWIDE CORPORATION (UK) LTD

Company Name

RELIANCE WORLDWIDE CORPORATION (UK) LTD

Address

HORTON ROAD WEST DRAYTON

Postcode

UB7 8JL

Country

United Kingdom

Phone

+44 7730 052060

General Email

PETER.LANCASTER@RWC.COM

View All Listings by this Company

Range of stainless-steel braided EPDM lined flexible hose assemblies with EPDM seals, available with a variety of end connections, some of which include isolation valves (see model). For use with: Copper Pipes manufactured in accordance with BS EN 1057 Plastic PB pipes manufactured in accordance with BS 7291-2 Plastic PEX pipes manufactured in accordance with BS 7291-3 Maximum working pressure: 6.0 bar @ 65°C Maximum working pressure: 12.0 bar @ 20°C

Section:

1863 Tubes

Section Subtitle:

Elastomeric.

WRAS Approval Number:

241202054

Basis of Compliance:

Tested to regulators Specification Test Code Sheets

Note:

12BAR @ 20°C

Size:

See model

Marking:

Qualflex, QWRAS, 6bar@65°c /12 bar @20°c, DOM (M.YY) stamped on ferrule

Installation Requirements:

R001 R008

Expiry date:

31/12/2029

Model:

08SW: DN08 Classic Range, 8mm ID EPDM Liner with Stainless Steel Braiding 10SW: DN10 Classic Range, 10mm ID EPDM Liner with Stainless Steel Braiding 12SW: DN12 Classic Range, 12mm ID EPDM Liner with Stainless Steel Braiding 19SW: DN19 Classic Range, 19mm ID EPDM Liner with Stainless Steel Braiding 25SW: DN25 Classic Range, 25mm ID EPDM Liner with Stainless Steel Braiding Hose assembly part number follows the below format: (The example given is for a Ø8mm internal diameter, Premier Plus Range, 900mm overall length, female to male hose assembly) Fittings codes: M – (MALE) F – (FEMALE) C – (COMPRESSION) S – STANDPIPE E – (ELBOW) J – (JG PUSHFIT) P – (HYDRA PUSHFIT) The hose can further be identified by its description which also specifies the fitting sizes and material:

Product Images

Manufacturer:

Hydralectric Group Ltd.

Company Name

Hydralectric Group Ltd.

Address

5 High Road, Byfleet, Surrey

Postcode

KT14 7QE

Country

United Kingdom

Phone

+44 1932 334 200

View All Listings by this Company

Range of stainless-steel braided EPDM lined flexible hose assemblies with EPDM seals, available with a variety of end connections, some of which include isolation valves (see model). For use with: Copper Pipes manufactured in accordance with BS EN 1057 Plastic PB pipes manufactured in accordance with BS 7291-2 Plastic PEX pipes manufactured in accordance with BS 7291-3 Maximum working pressure: 6.0 bar @ 65°C Maximum working pressure: 12.0 bar @ 20°C

Section:

1863 Tubes

Section Subtitle:

Elastomeric.

WRAS Approval Number:

241202063

Basis of Compliance:

Tested to regulators Specification Test Code Sheets

Size:

See model

Marking:

Qualflex, QWRAS, 6bar@65°c /12 bar @20°c, DOM (M.YY) stamped on ferrule

Installation Requirements:

R001 R008

Expiry date:

31/12/2029

Model:

T01001 - 15mm Brass C (Compression) and ½” F (Female) T01002 - 15mm Brass C (Compression) and ½” Plastic F (Female) T01003 -15mm Brass C (Compression) and ¾ ” Plastic F (Female) T01004 -15mm Brass C (Compression) and ½” Plastic F (Female) T01005 - 15mm Brass C (Compression) and ¾ ” Plastic F (Female) T01006 - 15mm Brass C (Compression) and 1/2 ” Plastic F (Female) T01007 - 22mm Brass C (Compression) and ¾” Plastic F (Female) T01008 - 15mm Brass C (Compression) and 1/2 ” Plastic F (Female) T01009 - 22mm Brass C (Compression) and 3/4 ” Plastic F (Female) T01010 - 22mm Brass C (Compression) and 3/4 ” Plastic F (Female) T01011 - 22mm Brass C (Compression) and 3/4 ” Plastic F (Female) T01012 - 15mm Brass C (Compression) and 15mm Brass C (Compression) T01013 - 22mm Brass C (Compression) and 22mm Brass C (Compression) T01014 - 15mm Brass C (Compression) and ½” Brass F (Female) T01015 - 15mm Brass C (Compression) and ½” Plastic F (Female) T01016 - 22mm Brass C (Compression) and 3/4” Plastic F (Female) T01017 - ½” Brass F (Female) and ½” Brass F (Female) T01018 - 15mm Hydra Pushfit (P) and 15mm Hydra Pushfit (P) T01019 - 22mm Hydra Pushfit (P) and 22mm Hydra Pushfit (P) T01020 - 15mm Hydra Pushfit (P) and ½” Plastic F (Female) T01021 - 15mm Hydra Pushfit (P) and 3/4” Plastic F (Female) T01022 - 22mm Hydra Pushfit (P) and 3/4” Plastic F (Female) T01023 - 15mm Hydra Pushfit (P) and 1/2” Plastic F (Female) T01024 - 15mm Hydra Pushfit (P) and 3/4” Plastic F (Female) T01025 - 22mm Hydra Pushfit (P) and 3/4” Plastic F (Female) T01026 - 15mm Hydra Pushfit (P) and 1/2” Plastic F (Female) T01027 - 22mm Hydra Pushfit (P) and 3/4” Plastic F (Female) T01028 - 15mm Brass C (Compression)and 1/2” Brass FE (Female Elbow) T01029 - 15mm Brass C (Compression) and 1/2” Brass FE (Female Elbow) T01030 - 15mm Hydra Pushfit (P) and 1/2” Brass FE (Female Elbow) T01031 - 10mm Brass Male (M) and 15mm Brass C (Compression) T01032 - 12mm Brass Male (M) and 15mm Brass C (Compression) T01033 - 10mm Brass Male (M) and 15mm Hydra Pushfit (P) T01034 - 12mm Brass Male (M) and 15mm Hydra Pushfit (P)

Approval Holder:

UK Plumbing Supplies Ltd

Company Name

UK Plumbing Supplies Ltd

Address

Quayside 2A Wilderspool Park Greenalls Avenue Cheshire

Postcode

WA4 6HL

View All Listings by this Company

Manufacturer:

Hydralectric Group Ltd.

Company Name

Hydralectric Group Ltd.

Address

5 High Road, Byfleet, Surrey

Postcode

KT14 7QE

Country

United Kingdom

Phone

+44 1932 334 200

View All Listings by this Company

Range of stainless-steel braided EPDM lined flexible hose assemblies with EPDM seals, available with a variety of end connections. Maximum working pressure: 6.0 bar @ 65°C Maximum working pressure: 12.0 bar @ 20°C

Section:

1863 Tubes

Section Subtitle:

Elastomeric.

WRAS Approval Number:

241202067

Basis of Compliance:

Tested to regulators Specification Test Code Sheets

Note:

12BAR @ 20°C

Size:

See model

Marking:

Qualflex, QWRAS, 6bar@65°c /12 bar @20°c, DOM (M.YY) stamped on ferrule

Installation Requirements:

R001 R008

Expiry date:

31/12/2029

Model:

(HOSE900001): DN10 x Brass 3/4BSP Female Elbow x Brass 1/2BSP Female straight. (HOSE202105): DN10 x Brass 3/4BPP Female Straight x Brass 3/4BSP Male (HOSE900004): DN10 x Brass 3/8BSP Female Elbow x Brass 1/2BSP Female straight (HOSE202107): DN10 x Brass 3/4BSP Female Elbow x Brass 3/4BSP Female straight. (HOSE265012) : DN10 x Brass 15mm Compression x Brass 3/8NPT Male

Approval Holder:

RELIANCE WORLDWIDE CORPORATION (UK) LTD

Company Name

RELIANCE WORLDWIDE CORPORATION (UK) LTD

Address

HORTON ROAD WEST DRAYTON

Postcode

UB7 8JL

Country

United Kingdom

Phone

+44 7730 052060

General Email

PETER.LANCASTER@RWC.COM

View All Listings by this Company

Manufacturer:

Hydralectric Group Ltd.

Company Name

Hydralectric Group Ltd.

Address

5 High Road, Byfleet, Surrey

Postcode

KT14 7QE

Country

United Kingdom

Phone

+44 1932 334 200

General Email

jamie.balkwill@hydralectric.com

View All Listings by this Company

Nimbus Compact range of combination heat pump units with enamel lined tank and stainless-steel coil. Fitted with a magnesium anode, expansion vessel and T&P valve set at 7 bar & 95°C. supplied with an inlet control group consisting of a pressure reducing valve, strainer, pressure relief valve and single check valve, and a tundish. Max working pressure 6.0 Bar Max operating Temperature 80 °C

Section:

1890 Unvented Heating Apparatus

Basis of Compliance:

Tested to regulators Specification Test Code Sheets

Marking:

Ariston address, model no & product info on adhesive label.

Installation Requirements:

R001 R140 R360

Expiry date:

30/11/2029

Model:

3302563 Nimbus Compact-UK 35M Net R32, 3302564 Nimbus Compact-UK 50M Net R32, 3302565 Nimbus Compact-UK 80M Net R32, 3302566 Nimbus Compact-UK 80M T Net R32, 3302567 Nimbus Compact-UK 120M Net R32, 3302568 Nimbus Compact-UK 120M T Net R32, 3302569 Nimbus Compact-UK 150M Net R32, 3302570 Nimbus Compact-UK 150 M T Net R32.

Product Images

Approval Holder:

Ariston S.p.A.

Company Name

Ariston S.p.A.

Address

Viale A. Merloni 45 60044 Fabriano (AN)

Country

Italy

Phone

+39 349 3206673

General Email

francesco.sinna@ariston.com

View All Listings by this Company

Range of vertical cased and insulated direct and indirect unvented stainless steel hot water storage cylinders. Fitted with a Caleffi 309463 GLD temperature and pressure relief valve sat at 6 bar & 90°C, and supplied with an inlet control group consisting of in-line pressure reducing valve (Caleffi set at 3 bar) and pressure relief valve (Caleffi CWIC200055) set at 4.5 bar, and incorporates a stainless-steel mesh and an approved check valve cartridge (verified by test suitable for backflow protection against Fluid Category 2), expansion vessel and filling loop. Maximum working pressure 4.4 bar. Maximum operating temperature 99°C.

Section:

1890 Unvented Heating Apparatus

Size:

28mm compression.

Marking:

Ideal Heating, Manufacturers name, address, date of manufacturer, capacity, model no, serial no, pressure and technical information on adhesive label on body.

Installation Requirements:

R001 R140 R360 R511 R530

Expiry date:

31/05/2028

Model:

IDEPLUHP150DUOPPSZSL & IDEPLUHP180DUOPPSZSL. 475mm diameter 150, 180, litre; single coil cylinders on top of a buffer cylinder for coupling with a range of heat pumps 5kW to 14kW; Pre-plumbed and pre-wired; single zone

Approval Holder:

Ideal Boilers Ltd

Company Name

Ideal Boilers Ltd

Address

PO Box 103 National Avenue Hull East Yorkshire

Postcode

HU5 4JN

Country

United Kingdom

Phone

07775659359

General Email

ben.higinbotham@groupe-atlantic.co.uk

View All Listings by this Company

Wall mounted, thermostatic blending valve (chrome plated brass body). Temperature is pre-set under fixed cap. The inlets incorporate an approved check valve cartridge, however, the complete assembly has not been fully tested to demonstrate that it provides backflow protection. The product is supplied with plastic strainers and screwdriver operated spherical valves, intended for installation at each inlet. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.

Section:

2010 Shower Valves

Section Subtitle:

Shower valve(s) with thermostatic temperature control

WRAS Approval Number:

241203010

Basis of Compliance:

Tested to regulators Specification Test Code Sheets

Note:

Product is not supplied with shower hose, handset or riser rail.

Size:

28mm Compression

Marking:

Bristan on Cap.

Installation Requirements:

R001 R010 R040

Expiry date:

31/12/2029

Model:

TS6000ECP

Product Images

Approval Holder:

Bristan Group Ltd.

Company Name

Bristan Group Ltd.

Address

Birch Coppice Business Park Dorden Tamworth

Postcode

B78 1SG

Country

Staffs

Phone

01827 254144

General Email

hmistry@bristan.com

View All Listings by this Company

Section:

2010 Shower Valves

Description:

A Shower valve(s) with thermostatic temperature control

Wall mounted. Supplied with riser rail. Inlets incorporate approved single check valve cartridges however, the complete product has not been fully tested to demonstrate it provides backflow protection.

Basis of Compliance:

Tested to regulators Specification Test Code Sheets

Installation Requirements:

R001 R020

Expiry date:

31/05/2030

Product Images

Approval Holder:

Bristan Group Ltd.

Company Name

Bristan Group Ltd.

Address

Birch Coppice Business Park Dorden Tamworth

Postcode

B78 1SG

Country

Staffs

Phone

01827 254144

General Email

hmistry@bristan.com

View All Listings by this Company

Section:

2010 Shower Valves

Description:

A Range of Shower valve(s) with thermostatic temperature control

Wall Mounted Concealed. Inlets incorporate approved single check valve cartridges however, the complete product has not been fully tested to demonstrate it provides backflow protection.

Basis of Compliance:

Tested to regulators Specification Test Code Sheets

Installation Requirements:

R001 R020

Expiry date:

30/06/2030

Notes & Further Information

Product Images

Approval Holder:

Bristan Group Ltd.

Company Name

Bristan Group Ltd.

Address

Birch Coppice Business Park Dorden Tamworth

Postcode

B78 1SG

Country

Staffs

Phone

01827 254144

General Email

hmistry@bristan.com

View All Listings by this Company

Range of below ground (screw down type) fire hydrants with coated cast iron bodies. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.

Section:

2070 Valves

Section Subtitle:

Fire hydrant. Where possible, above ground fire hydrants should be considered. The location of fire hydrants should be site specific and subject to assessment of fluid category risk.

WRAS Approval Number:

250102712

Basis of Compliance:

Tested to regulators Specification Test Code Sheets

Size:

DN80 to DN150 flanged connections

Marking:

NAFFCO logo, model code, DN, PN, date of manufacture (MM/YYYY) and other technical data on data plate on body.

Installation Requirements:

R001 R415

Expiry date:

31/01/2030

Model:

NHYD 058D-W, 100 NFHQS-CD 800/1200, 150 NFHQS-CD 800/1200, 100 NHC 800/1200, 100 NFHQV-CD1/CD2 & 150 NFHQV-CD1/CD2.

Product Images

Manufacturer:

NATIONAL FIRE FIGHTING MANUFACTURING FZCO

Company Name

NATIONAL FIRE FIGHTING MANUFACTURING FZCO

Address

PO BOX NO.# 262169, Jebel Ali Free Zone, Dubai

Country

UAE

View All Listings by this Company

Range of non-return, swing gate valves with bronze, DZR brass or brass bodies and DZR brass, bronze or brass discs. Maximum working pressure 20.0 bar or 16.0 bar (please refer to model) Maximum operating temperature 85°C.

Section:

2188 Valves

Section Subtitle:

Non-return, swing gate, resilient trim. Devices listed under this heading do not provide sufficient protection against backflow to meet the requirements of The Water Supply (Water Fittings) Regulations 1999 (England and Wales), The Water Supply (Water Fittings) (Scotland) Byelaws 2014 or The Water Supply (Water Fittings) Regulations (Northern Ireland) 2009. For this purpose reference should be made to `Backflow Prevention Devices`.

WRAS Approval Number:

240702714

Basis of Compliance:

Tested to regulators Specification Test Code Sheets

Size:

½” to 2” BSPT (F), NPT (F) or BSPP (F).

Marking:

IVAL logo, size, PN and flow arrow on body.

Installation Requirements:

R001

Expiry date:

31/07/2029

Model:

C40 Range

Approval Holder:

IVAL Hydronics UK Ltd

Company Name

IVAL Hydronics UK Ltd

Address

71-75 Shelton Street, Covent Garden, London.

Postcode

WC2H 9JQ

Country

United Kingdom

General Email

info@ival-hydronics.co.uk

View All Listings by this Company

In-line, manually adjustable pressure reducing valves with DZR brass bodies. Maximum inlet supply pressure 16.0 Bar. Maximum outlet pressures between 1.5 bar and 6.0 bar. Cold water use only.

Section:

2200 Valves

Section Subtitle:

Pressure reducing.

WRAS Approval Number:

241004728

Basis of Compliance:

Tested to regulators Specification Test Code Sheets

Size:

See model.

Marking:

Brand logo, Model code, DN, PN, Flow Arrow, DR/CR Mark & DOM (YYWW) on body.

Installation Requirements:

R001 R120

Expiry date:

31/10/2029

Model:

D04FM-1/2A – ½” BSP (F) inlet/outlet. D04FM-3/4A – ¾” BSP (F) inlet/outlet. D04FM-3/4ZFR - ¾” captive nut inlet x ¾” BSP (M) outlet

Product Images

Approval Holder:

Pittway Sarl

Company Name

Pittway Sarl

Address

A3 - ZA La Pièce 6 1180 Rolle

Country

Switzerland

View All Listings by this Company

Range of in-line, manually adjustable pressure reducing valves with nickel plated DZR brass body. Maximum inlet supply pressure 25 bar. Maximum operating temperature 80°C

Section:

2200 Valves

Section Subtitle:

Pressure reducing.

WRAS Approval Number:

240904734

Basis of Compliance:

Tested to regulators Specification Test Code Sheets

Size:

See models

Marking:

Pegler logo (Brand of Aalberts), DN, DR, PN and flow arrow on body

Installation Requirements:

R001 R120

Expiry date:

30/09/2029

Model:

5A2091 - ½” PRV6PT DZR Prs Red Vlv NP FXF– CR (DZR) 1.0 to 5.5 bar G ½“, 5A2092 - ¾” PRV6PT DZR Prs Red Vlv NP FXF (DZR) 1.0 to 5.5 bar G ¾“, 5A2093 – 1” PRV6PT DZR Pres Red Vlv NP FXF (DZR) 1.0 to 5.5 bar G 1”, 5A2094 – 1.1/4” PRV6PT DZR PRV NP FXF (DZR) 1.5 to 5.5 bar G 1 ¼“, 5A2095 – 1.1/2” PRV6PT DZR PRV NP FXF (DZR) 1.5 to 5.5 bar G 1 ½“, 5A2096 – 2” PRV6PT DZR PRV NP FXF (DZR) 1.5 to 5.5 bar G 2”, 5A2097 – 2.1/2” PRV6PT DZR PRV NP FXF(DZR) 1.5 to 5.5 bar G 2 ½“, 5A2098 – 3” PRV6PT DZR PRV NP FXF 1.5 to 5.5 bar light. G 3”, 5A2099 – 4” PRV6PT DZR PRV NP FXF (DZR) 1.5 to 5.5 bar G 4”.

Approval Holder:

Aalberts Integrated Piping Systems Ltd.

Company Name

Aalberts Integrated Piping Systems Ltd.

Address

St. Catherines Avenue Doncaster South Yorkshire

Postcode

DN4 8DF

Country

United Kingdom

Phone

+447843075405

General Email

gavin.peters@aalberts-ips.com

View All Listings by this Company

Range of pressure reducing valves with DZR brass or bronze bodies and manually adjustable outlet pressure range between 2.5bar to 6.0bar. Maximum working pressure: 25.0 bar. Maximum operating temperature 80°C.

Section:

2200 Valves

Section Subtitle:

Pressure reducing.

WRAS Approval Number:

241204731

Basis of Compliance:

Tested to regulators Specification Test Code Sheets

Size:

see models

Marking:

VIR, CR, PN, size & flow arrow on body.

Installation Requirements:

R001 R120

Expiry date:

31/12/2029

Model:

9610DR DN15 (1/2” BSP (F)), DN20 (3/4” BSP (F)), DN25 (1” BSP (F)), DN32 (1 1/4” BSP (F)), DN40 (1 1/2” BSP (F)), DN50 (2” BSP (F)).

Approval Holder:

VIR Valvoindustria Ing. Rizzio S.p.A.

Company Name

VIR Valvoindustria Ing. Rizzio S.p.A.

Address

Via Circonvallazione n. 10, 13018 Valduggia (VC)

Country

Italy

View All Listings by this Company

Range of in-line, pressure reducing valves with DZR brass bodies and stainless-steel strainers. Push fit versions only can also be used with both polybutylene pipe (manufactured to BS7291-2) and PEX pipe (manufactured to BS7291-3) Maximum inlet supply pressure 16.0 bar. Outlet supply pressure is adjustable within the range of 1.5 bar to 6.0 bar. Cold water use only.

Section:

2200 Valves

Section Subtitle:

Pressure reducing.

WRAS Approval Number:

250302717

Basis of Compliance:

Tested to regulators Specification Test Code Sheets

Size:

15mm or 22mm push fit.

Marking:

JG (John Guest), DR and flow arrow on body. Reliance logo, pressure and temperature on valve.

Installation Requirements:

R001

Expiry date:

31/03/2030

Model:

Cold water 312 Compact Series comprising of models: PRED312100, PRED312110

Product Images

Approval Holder:

RELIANCE WORLDWIDE CORPORATION (UK) LTD

Company Name

RELIANCE WORLDWIDE CORPORATION (UK) LTD

Address

HORTON ROAD WEST DRAYTON

Postcode

UB7 8JL

Country

United Kingdom

Phone

+44 7730 052060

General Email

PETER.LANCASTER@RWC.COM

View All Listings by this Company

Range of in-line, manually adjustable pressure reducing valves with brushed chrome DZR brass bodies. Outlet pressure range: 1.0 - 6.0 bar. Maximum working pressure 16.0 bar. Maximum operating temperature 80°C.

Section:

2200 Valves

Section Subtitle:

Pressure reducing.

WRAS Approval Number:

250304721

Basis of Compliance:

Tested to regulators Specification Test Code Sheets

Size:

½” BSP (F) ¾” BSP (F) 15mm compression 22mm compression

Marking:

Officine Rigamonti Spa logo, DN, PN, flow arrow, DR, Made in Italy on body.

Installation Requirements:

R001 R120

Expiry date:

31/03/2030

Model:

Art.0218.515 Art.0218.514 Art.0218.520 Art.0218.522

Product Images

Manufacturer:

Officine Rigamonti Spa

Company Name

Officine Rigamonti Spa

Address

Via Circonvallazione 9, Officine Rigamonti spa 13018 Valduggia (VC)

Country

Italy

Phone

+39 0163 48 165 Fax: +39 0163347254

View All Listings by this Company

Range of pilot operated, pressure reducing valves epoxy coated ductile iron bodies. The valves are supplied with a pilot valve, spherical valves and a needle valve. Outlet pressure setting is adjustable in the range of 1.0 bar to 12.0 bar. Maximum supply pressure 16.0 bar. Maximum operating temperature 85°C.

Section:

2205 Valves

Section Subtitle:

Pressure reducing, pilot operated.

WRAS Approval Number:

241202717

Basis of Compliance:

Tested to regulators Specification Test Code Sheets

Size:

DN50, DN65, DN80, DN100, DN125, DN150, DN200, DN250, DN300, DN350 & DN400

Marking:

AMEXSA on body.

Installation Requirements:

R001

Expiry date:

31/12/2029

Model:

AME-PDV

Approval Holder:

AGROHIDRAULICA DE MEXICO, S.A. DE C.V.

Company Name

AGROHIDRAULICA DE MEXICO, S.A. DE C.V.

Address

RIO QUERETARO #90-A COL. LA SIERRITA C.P. 76154, QUERETARO, QRO. MEXIC RFC: AME 120917 269

View All Listings by this Company

Range of press fit spherical valves with chrome plated brass bodies, to be used with copper pipe EN1057. Crimp joint is achieved by a M profile crimp. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.

Section:

2260 Valves

Section Subtitle:

Spherical, metal.

WRAS Approval Number:

241104008

Basis of Compliance:

Tested to regulators Specification Test Code Sheets

Size:

See models.

Marking:

V&G, size, flow arrow, date of manufacture (MM-YY) etched on body

Installation Requirements:

R001

Expiry date:

30/11/2029

Model:

Straight servicing valve, screwdriver operated 10.60292.15T.CP4V-8510 15mm crimp fix x 1/2" BSP captive nut (F) Angle servicing valve, screwdriver operated 10.60372.15T.CP4V-8510 15mm crimp fix x 1/2" BSP captive nut (F) Angle washing machine valve with handle 10.60652.15K.CP4V-8510 15mm crimp fix x 3/4" BSP (M) Tee washing machine valve with handle 10.60782.15K.CP4V-8510 15mm crimp fix x15mm crimp fix 3/4" BSP (M) Straight washing machine valve with handle 10.60492.15K.CP4V-8510 15mm crimp fix x 3/4" BSP (M)

Product Images

Manufacturer:

Zhejiang Valogin Technology Co. Ltd

Company Name

Zhejiang Valogin Technology Co. Ltd

Address

Qinggang Industrial Zone, Yuhuan, Taizhou

Country

Zhejiang

View All Listings by this Company

Range of spherical valves with either brass (BFIVB-15, BFIVBL-15 & BFIVHPL-15 models) or nickel plated (BFIV-15, BFIVL-15,BFIVL-22 & BFSVB-15D models) brass bodies with chrome plated brass ball and operated via lever, butterfly type handle or screwdriver slot. For use with copper pipe (manufactured to EN1057). Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.

Section:

2260 Valves

Section Subtitle:

Spherical, metal.

WRAS Approval Number:

240404069

Size:

see model

Marking:

MSL, size & date of manufacture (MM-YY) on body. EN1254-2 & size on nut.

Installation Requirements:

R001

Expiry date:

30/04/2029

Model:

ISO valve BFIVB-15 15MM Compression BFIV-15 15MM Compression ISO valve with handle BFIVBL-15 15MM Compression BFIVL-15 15MM Compression BFIVHPL-15 15MM Compression Angle Servicing valve BFSVB-15D 15mm compression x 1/2 captive nut Straight Servicing valve BFSVS-15D 15mm compression x 1/2 captive nut Butterfly operated. BFIVL-22 22MM Compression

Approval Holder:

Navigator MSL Ltd.

Company Name

Navigator MSL Ltd.

Address

Mill Road, Sharnbrook, Beds.

Postcode

MK44 1NP

Phone

01234 781234

View All Listings by this Company

Screwdriver operated spherical valve with a brass & DZR brass body. The fitting incorporates two approved single check valve cartridges however, the complete product has not been fully tested to demonstrate it provides backflow protection. Maximum working pressure 10 Bar. Maximum operating temperature 85°C.

Section:

2260 Valves

Section Subtitle:

Spherical, metal.

WRAS Approval Number:

241202016

Basis of Compliance:

Tested to regulators Specification Test Code Sheets

Size:

½” BSP swivel nut inlet x 3/8” BSP (M) outlet

Marking:

Airaga Rubinetterie logo, CR on body

Installation Requirements:

R001

Expiry date:

31/12/2029

Model:

AI-0312A0403HI

Product Images

Manufacturer:

Altecnic Limited

Company Name

Altecnic Limited

Address

Francesco House, Staples Close Stafford Staffordshire

Postcode

ST16 1WQ

Country

United Kingdom

Phone

+44 (0)1785 218200

View All Listings by this Company

Screwdriver operated spherical valve with a DZR brass body. Maximum working pressure 10 Bar Maximum operating temperature 85°C

Section:

2260 Valves

Section Subtitle:

Spherical, metal.

WRAS Approval Number:

241202017

Basis of Compliance:

Tested to regulators Specification Test Code Sheets

Size:

½” BSP swivel nut inlet x 3/8” BSP (M) outlet

Marking:

Airaga Rubinetterie logo, CR on body

Installation Requirements:

R001

Expiry date:

31/12/2029

Model:

AI-0312A0403CG

Product Images

Approval Holder:

Altecnic Limited

Company Name

Altecnic Limited

Address

Francesco House, Staples Close Stafford Staffordshire

Postcode

ST16 1WQ

Country

United Kingdom

Phone

+44 (0)1785 218200

General Email

sales@altecnic.co.uk

View All Listings by this Company

Range of in-line angled or ‘T’ type spherical valves with chromium plated brass, nickel plated brass, brass or DZR brass bodies and brass ball. Models have screwdriver, lever or butterfly operating members. Maximum working pressure 10.0, 16.0 or 25.0 Bar. Maximum operating temperature 85° or 99°C.

Section:

2260 Valves

Section Subtitle:

Spherical, metal.

WRAS Approval Number:

241202046

Basis of Compliance:

Tested to regulators Specification Test Code Sheets

Size:

See models.

Marking:

IDC logo E mark (~E~ within circle), size and flow arrow on valve body. The DZR models are marked 'CR'.

Installation Requirements:

R001

Expiry date:

31/12/2029

Model:

Brass & Nickle Plated - 25 bar 99°C 1BVC102 1/4" MxM thread ball Valve 1BVC103 3/8" MxM thread ball Valve 1BVC104 1/2" MxM thread ball Valve 1BVC106 3/4" MxM thread ball Valve 1BVC108 1" MxM thread ball Valve 1BVC110 1 1/4" MxM thread ball Valve 1BVC112 1 1/2" MxM thread ball Valve 1BVC114 2" MxM thread ball Valve DZR Brass - 25 bar 99°C 1BVC202 1/4" MxM thread ball valve DZR 1BVC203 3/8" MxM thread ball valve DZR 1BVC204 1/2" MxM thread ball valve DZR 1BVC206 3/4" MxM thread ball valve DZR 1BVC208 1" MxM thread ball valve DZR 1BVC220 1 1/4" MxM thread ball valve DZR 1BVC222 1 1/2" MxM thread ball valve DZR 1BVC224 2" MxM thread ball valve DZR Brass & Nickle Plated - 25 bar 99°C 1BVD102 1/4" FxM thread ball Valve 1BVD103 3/8" FxM thread ball Valve 1BVD104 1/2" FxM thread ball Valve 1BVD106 3/4" FxM thread ball Valve 1BVD108 1" FxM thread ball Valve 1BVD110 1 1/4" FxM thread ball Valve 1BVD112 1 1/2" FxM thread ball Valve 1BVD114 2" FxM thread ball Valve DZR Brass - 25 bar 99°C 1BVD202 1/4" FxM thread ball valve DZR 1BVD203 3/8" FxM thread ball valve DZR 1BVD204 1/2" FxM thread ball valve DZR 1BVD206 3/4" FxM thread ball valve DZR 1BVD208 1" FxM thread ball valve DZR 1BVD220 1 1/4" FxM thread ball valve DZR 1BVD222 1 1/2" FxM thread ball valve DZR 1BVD224 2" FxM thread ball valve DZR Brass & Nickle Plated - 10 bar 85°C 1WMC101 Tee washing machine valve 15mm x 15mm x 3/4"M NP 1WMC201NP Tee washing machine valve 15mm compression NP 1FWA100 Straight service valve 14.7mm compression x 1/2'F NP 1FWA101 Straight service valve 15mm compression x 1/2"F NP 1FWA102 Straight service valve 22mm compression x 3/4”F NP 1FWB100 Angle service valve 14.7mm compression x 1/2”F NP 1FWB101 Angle service valve 15mm compression x 1/2”F NP 1WMB103NP Angle isolation valve 15mm compression x 3/8M NP 1WMB102NP Angle isolation valve 15mm compression x 1/2”M NP 1WMB101NP Angle isolation valve 15mm compression x 3/4”M NP 1GLE011NP Angle isolation valve 15mm compression NP 1GLE113NP Angle isolation valve 15mm compression x 3/8”M NP 1GLE112NP Angle isolation valve 15mm compression x 1/2”M NP Brass - 10 bar 85°C 1GLE011 Angle isolation valve 15mm compression Brass & Nickle Plated 10 bar 85°C 1WHA103NP Straight isolation valve 15mm compression x 3/8"M NP 1WHA102NP Straight isolation valve 15mm compression x 1/2”M NP 1WHA201NP Straight isolation valve 22mm compression x 3/4”M NP 1WHA100LNP Straight isolation valve 14.7mm compression x 3/4”M with level handle NP 1WMA101LNP Straight isolation valve 15mm compression x 3/4”M with level handle NP 1GLA000NP Straight isolation valve 14.7mm compression NP 1GLA000LNP Straight isolation valve 14.7mm compression with level handle NP 1GLA010NP Straight isolation valve 15mm compression NP 1GLA010LNP Straight isolation valve 15mm compression with level handle NP 1GLA020NP Straight isolation valve 22mm compression NP 1GLA020LNP Straight isolation valve 22mm compression with level handle NP Brass - 10 bar 85°C 1GLA000 Straight isolation valve 14.7mm compression 1GLA000L Straight isolation valve 14.7mm compression with level handle 1GLA010 Straight isolation valve 15mm compression 1GLA020 Straight isolation valve 22mm compression 1GLA010L Straight isolation valve 15mm compression with level handle 1GLA020L Straight isolation valve 22mm compression with level handle Brass - 16 bar 85°C 1GLC011 Straight Isolation valve full bore 15mm compression 1GLC021 Straight Isolation valve full bore 22mm compression Brass - 25 bar 85°C 1GLB010 Straight isolation valve full bore 15mm compression heavy pattern 1GLB020 Straight isolation valve full bore 22mm compression heavy pattern DZR Brass Nickle Plated - 10 bar 85°C 1GLAa00NP Straight isolation valve 14.7mm compression DZR NP 1GLAa10NP Straight isolation valve 15mm compression DZR NP 1GLAa10LNP Straight isolation valve 15mm compression DZR with level handle NP 1GLAa20LNP Straight isolation valve 22mm compression DZR with level handle NP 1GLAa20NP Straight isolation valve 22mm compression DZR NP DZR Brass Nickle Plated - 25 bar 85°C 1GLBa10NP Straight isolation valve full bore 15mm compression DZR NP 1GLBa20NP Straight isolation valve full bore 22mm compression DZR NP Nickle Plated Brass - 16 bar 85°C 1GLC011NP Straight Isolation valve full bore 15mm compression NP 1GLC021NP Straight Isolation valve full bore 22mm compression NP Nickle Plated Brass - 25 bar 85°C 1GLB010LNP Straight isolation valve full bore 15mm compression with level handle NP 1GLB010NP Straight isolation valve full bore 15mm compression heavy pattern NP 1GLB020LNP Straight isolation valve full bore 22mm compression with level handle NP 1GLB020NP Straight isolation valve full bore 22mm compression heavy pattern NP

Product Images

Approval Holder:

IDC Plumbing & Heating Technology (Beijing) Ltd

Company Name

IDC Plumbing & Heating Technology (Beijing) Ltd

Address

3rd Floor, Unit 2, Building 2, Section A Zhaowei Science & Technology Park No. 14, Jiuxianqiao Road Chaoyang District Beijing

Postcode

100015

Country

China

Phone

008610 51659550 ext 312

General Email

Jerry.tang@idcgroup.com.cn

View All Listings by this Company

Manufacturer:

IDC Fluid Control Co., Ltd.

Company Name

IDC Fluid Control Co., Ltd.

Address

No.6, Shengyuan Road, Mechanical & Electrical Industrial Zone, Yuhuan City, Zhejiang, Taizhou City, Zhejiang Province, P. R.China

Country

China

General Email

View All Listings by this Company

Spherical valves incorporating a drain port and two check valve cartridges (verified by test, suitable for backflow protection against fluid category 3) in a DZR brass body. Above ground use only. Maximum working pressure 10.0 bar. Maximum operating temperature 85°C.

Section:

2260 Valves

Section Subtitle:

Spherical, metal.

WRAS Approval Number:

241204013

Basis of Compliance:

Tested to regulators Specification Test Code Sheets

Size:

290460 1” BSP(F) x 1”BSP(F) 290450 3/4” BSP(F) x 1” BSP(F)

Marking:

Altecnic logo, flow arrow and CR on body

Installation Requirements:

R001 R511

Expiry date:

31/12/2029

Model:

290450 290460

Product Images

Manufacturer:

Caleffi S.p.A

Company Name

Caleffi S.p.A

Address

Strada Regionale 229 n. 25 Fontaneto d'Agogna (NO)

Postcode

28010

Country

Italy

Phone

+39 0322 8491

View All Listings by this Company

Screwdriver operated angled spherical valve with a brass body and ball. Compression connection is to be used with copper pipe EN1057. Maximum working pressure 12.0 bar. Maximum operating temperature 85°C.

Section:

2260 Valves

Section Subtitle:

Spherical, metal.

WRAS Approval Number:

250504002

Basis of Compliance:

Tested to regulators Specification Test Code Sheets

Size:

15mm compression x ½” BSP (M)

Marking:

Orkli logo on body, customer reference, production date and hour (DD/MM/YY, HH:MM) printed on body

Installation Requirements:

R001

Expiry date:

31/05/2030

Model:

9C23003 Sanitary ½” ball valve

Manufacturer:

Orkli S. Coop

Company Name

Orkli S. Coop

Address

Ctra. Zaldibia, s/n Ordizia

Postcode

20240

Country

Spain

Phone

+34 610 146 459

View All Listings by this Company

Range of screwdriver operated spherical valves with a brass body and either a chrome plated brass ball (4000120555 model) or brass ball (all other models). Maximum working pressure 10.0 bar. Maximum operating temperature 100°C.

Section:

2260 Valves

Section Subtitle:

Spherical, metal.

WRAS Approval Number:

241215006

Basis of Compliance:

Tested to regulators Specification Test Code Sheets

Size:

See model.

Marking:

0020203907 & 0020203908 models: NF (company logo), DN15, PN10 & date of manufacture (YYMM) on body. 0020012770 & 4000120555 models: NF (company logo), 1/2, PN10 & WRAS on body.

Installation Requirements:

R001

Expiry date:

31/12/2029

Model:

0020203907: ¾” BSP (M) x ¾” BSP (F), 0020203908: ½” BSP (M) x ¾” BSP (F), 0020012770: ½” BSP (M) x ¾” BSP (M), 4000120555: ½” BSP (M) x ¾” captive nut.

Product Images

Approval Holder:

NINGBO FRIENDSHIP BRONZE WARE CO., LTD

Company Name

NINGBO FRIENDSHIP BRONZE WARE CO., LTD

Address

No.268 The Industrial Park, Xiaolin Avenue, Cixi City, Ningbo City, Zhejiang Province

Country

China

General Email

sale808@nbfriendship.com

View All Listings by this Company

Manufacturer:

NINGBO FRIENDSHIP BRONZE WARE CO., LTD

Company Name

NINGBO FRIENDSHIP BRONZE WARE CO., LTD

Address

No.268 The Industrial Park, Xiaolin Avenue, Cixi City, Ningbo City, Zhejiang Province

Country

China

General Email

sale808@nbfriendship.com

View All Listings by this Company

Range of in-line angled or ‘T’ type spherical valves with chromium plated brass, nickel plated brass, brass or DZR brass bodies and brass ball. Models have screwdriver, lever or butterfly operating members. Maximum working pressure 10.0, 16.0 or 25.0 Bar. Maximum operating temperature 85° or 99°C.

Section:

2260 Valves

Section Subtitle:

Spherical, metal.

WRAS Approval Number:

241202061

Basis of Compliance:

Tested to regulators Specification Test Code Sheets

Size:

See models.

Marking:

SOUTH COAST SALES logo, size and flow arrow on valve body.

Installation Requirements:

R001

Expiry date:

31/12/2029

Model:

VB101 – 14.7mm x 14.7mm

Approval Holder:

South Coast Sales

Company Name

South Coast Sales

Address

1 Doughcloyne Industrial Estate, Sarsfield Road, Wilton, Cork.

Postcode

T12 TR62

Country

Ireland

Phone

00353 21 - 43 46 143

General Email

info@southcoastsales.com

View All Listings by this Company

Range of in-line angled or ‘T’ type spherical valves with chromium plated brass and brass ball. Models have screwdriver, lever or butterfly operating members. Maximum working pressure 10.0, 16.0 or 25.0 Bar. Maximum operating temperature 85° or 99°C.

Section:

2260 Valves

Section Subtitle:

Spherical, metal.

WRAS Approval Number:

241202062

Basis of Compliance:

Tested to regulators Specification Test Code Sheets

Size:

See models.

Marking:

ART41 – Albion logo, size, DN & PN on body ART18 – Albion logo, Flow arrow & size on body

Installation Requirements:

R001

Expiry date:

31/12/2029

Model:

ART41 DN8 – F 1/4"x M1/4" ART41 DN10 – F 3/8" x M 3/8" ART41 DN15 – F 1/2" x M 1/2" ART41 DN20 – F 3/4" x M 3/4" ART41 DN25– F 1" x M 1" ART41 DN32 – F 1 1/4" x M 1 1/4" ART41 DN40 – F 1 1/2" x M 1 1/2" ART41 DN50 – F 2" x M 2" ART18 DN15 – 15mm x 15mm ART18 DN22 – 22mm x 22mm

Approval Holder:

Albion Valves (UK) Limited

Company Name

Albion Valves (UK) Limited

Address

9a Fallbank Industrial Estate Dodworth Barnsley

Postcode

S75 3LS

Country

United Kingdom

Phone

01226 729900

General Email

samjed@albionvalvesuk.com

View All Listings by this Company

Range of lever or screwdriver operated in-line spherical valves (chrome plated brass body), brass ball and EPDM seals. Compression connection to be used with copper pipe EN1057. Maximum working pressure 10.0 bar. Maximum operating temperature 85°C.

Section:

2260 Valves

Section Subtitle:

Spherical, metal.

WRAS Approval Number:

250104016

Basis of Compliance:

Tested to regulators Specification Test Code Sheets

Size:

see models

Marking:

Justlink WRAS, Date of manufacture (YYYY) on valve body; flow arrow on body except for YG-QF-1/M7600120012004

Installation Requirements:

R001

Expiry date:

31/01/2030

Model:

YG-GLF-1/M7600380012001: 3/8”BSP(M)x15mm compression YG-QF-1/M7600120012004: ½”BSP(M)x½”BSP(M) YG-GLF-2/M7600120012016: ½”BSP(M)x½”BSP(M) YG-GLF-3/M7600120012013: ½”BSP(M)x½”BSP(M)

Product Images

Manufacturer:

Yuhuan Jianglin Plumbing Hose & Parts Inc.

Company Name

Yuhuan Jianglin Plumbing Hose & Parts Inc.

Address

2 Jindifu Road Yuhuan Economic Development Zone Yuhuan

Postcode

317600

Country

China

Phone

86-576-89901684

View All Listings by this Company

Range of spherical valves, with DZR brass bodies and brass ball (15mm size) or stainless steel ball (all other sizes). The products can be supplied with various operating members (see model). Jointing is achieved via a crimping tool, the 15-28mm sizes use a ‘M’ profile and the 35-54mm sizes use a ‘V’ profile. The press-fit connection is to be used with copper pipe (manufactured to EN 1057), stainless steel pipes (manufactured to EN10312) or carbon steel pipe (manufactured to EN10305-3). Maximum working pressure 25.0 bar. Maximum operating temperature 85°C.

Section:

2260 Valves

Section Subtitle:

Spherical, metal.

WRAS Approval Number:

250115004

Basis of Compliance:

Tested to regulators Specification Test Code Sheets

Size:

See model.

Marking:

Cottam and Preedy logo, size, PN25, DR and date of manufacture (MMYY) on body. CP24, Cottam and Preedy logo and WRAS logo on handle.

Installation Requirements:

R001

Expiry date:

31/01/2030

Model:

Press fit Ball Valve with Lever Handle: CP24-LPF0XX. Press fit Ball Valve with Tee Handle: CP24-TPF0XX. Where XX denotes size in mm: Press fit Ball Valve with Tee Handle: 15, 22 or 28 only. All other models: 15, 22, 28, 35, 42 or 54.

Product Images

Approval Holder:

Cottam and Preedy Limited

Company Name

Cottam and Preedy Limited

Address

Bishopsgate Works 68 Lower City Road Tividale Dudley West Midlands

Postcode

B69 2HF

Country

United Kingdom

View All Listings by this Company

Range of inline or angled screwdriver or lever operated spherical valves with brass or chromium plated brass bodies. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.

Section:

2260 Valves

Section Subtitle:

Spherical, metal.

WRAS Approval Number:

250302030

Basis of Compliance:

Tested to regulators Specification Test Code Sheets

Note:

For use with copper pipe manufactured to EN1057

Size:

See Models below

Marking:

Zhejiang Fansheng Logo on all models. Additional Markings: Size & Flow Arrow (Q6084.015, Q6017.022, Q609.015, Q6107.015 & Q6036.015) Flow Arrow (Q6202.022, Q6047.015 & Q6077.015) Size (Q2028.02) Size & PN (Q6106.015 & Q6106.022)

Installation Requirements:

R001

Expiry date:

31/03/2030

Model:

Lever Operated: Q6084.015: 15mm x 15mm Compression Q6098.015: 15mm x 15mm x 15mm Compression Q6064.015: 15mm Compression x 3/4" BSP (M) (Elbow) Q6047.015: 15mm Compression x 3/4" BSP (M) (Straight) Q6077.015: 15mm Compression x 3/4" BSP (M) (Tee) Screwdriver Operated: Q6017.015: 15mm x 15mm Compression Q6017.022: 22mm x 22mm Compression Q6107.015: 15mm x 15mm Compression Q6202.015: 15mm x 15mm Compression Q6106.015: 15mm x 15mm Compression Q6106.022: 22mm x 22mm Compression Q6036.015: 15mm Compression x 1/2" BSP Captive nut (ELBOW) Q6028.015: 15mm Compression x 1/2" BSP Captive nut (Straight) Q2028.028: 28mm Compression x 1-1/2" BSP Captive nut

Product Images

Manufacturer:

Zhejiang Fansheng Fluid Control Co., LTD

Company Name

Zhejiang Fansheng Fluid Control Co., LTD

Address

Putian Industrial Area Chumen Area Yuhuan City Zhejiang Province

Country

China

View All Listings by this Company

Range of lever operated spherical valves with nickel plated brass bodies, chromium plated brass ball, PTFE seats and a drain valve. Maximum working pressure 25.0 Bar Maximum operating temperature 100.0°C

Section:

2260 Valves

Section Subtitle:

Spherical, metal.

WRAS Approval Number:

240902087

Basis of Compliance:

Tested to regulators Specification Test Code Sheets

Size:

½” BSP (F) or ¾” BSP (F)

Marking:

Size and pressure on body. VIP On operating member

Installation Requirements:

R001

Expiry date:

30/09/2029

Model:

00/2042 (1/2”) (3/4”)

Approval Holder:

Valves Instruments Plus Ltd

Company Name

Valves Instruments Plus Ltd

Address

VIP House Chaddock Lane Astley Manchester

Postcode

M29 7JT

Country

United Kingdom

Phone

01942 885 700

View All Listings by this Company

Range of in-line angled or ‘T’ type spherical valves with chromium plated brass, nickel plated brass or brass bodies with chromium plated brass balls. Models incorporate lever or butterfly operating members. Maximum working pressure 10.0 Bar, 16 bar, 25 bar, 32 bar, 40 bar or 64 bar. Maximum operating temperature 100 °C.

Section:

2260 Valves

Section Subtitle:

Spherical, metal.

WRAS Approval Number:

250402041

Basis of Compliance:

Tested to regulators Specification Test Code Sheets

Size:

see models

Marking:

Models 124, 121, 121PB, 120PB, 120, 126, 130, 221, 221PB, 280, 220, 251, 256, 261, 298, 235R, 235B, 239, 253. EZFITT logo, batch number, PN, size on body. EZFITT logo, model code, size, temperature and PN on label attached to valve handle. Models 224PB, 257, 253”, 253, 240, 242, 244, 256 and 245. EZFITT logo, batch number, PN, size on body. EZFITT logo, model code and size on label attached to valve handle. Model 257 EZFITT logo, flow arrow, batch number PN, size on body. EZFITT logo, model code, size, temperature and PN on label attached to valve handle. Models 257 and 261 EZFITT logo, flow arrow, batch number PN, size on body. EZFITT logo, model code, size on label attached to valve handle. Model 237, EZFITT logo, batch number on body. EZFITT logo, model code, size, temperature and PN on label attached to valve handle. Model 246 EZFITT logo, PN and size on body.

Installation Requirements:

R001

Expiry date:

30/04/2030

Model:

Advance Series 220 - RTS F/F Flat handle 1/4", 3/8”; 1/2”; 3/4”; 1", 1"1/4; 1"1/2; 2”; 2"1/2; 3”; 4" 220PB - Blue - RTS F/F Flat handle 1/4", 3/8”, 1/2”, 3/4”, 1", 1"1/4, 1"1/2, 2”, 2"1/2, 3” 4" 280 - RTS F/F stainless steel flat handle 1/4"; 3/8”; 1/2”; 3/4”; 1"; 1"1/4; 1"1/2; 2”; 2"1/2; 3”; 4" 223 ADVANCE RTS F/F butterfly handle 1/4"; 3/8”; 1/2”; 3/4”; 1" 223PB - Blue - RTS F/F butterfly handle 1/4"; 3/8”; 1/2”; 3/4”; 1" 252 - RTS F/F flat handle with extension 1/2”; 3/4”; 1"; 1"1/4; 1"1/2; 2" 221 - RTS M/F Flat handle 1/4"; 3/8”; 1/2”; 3/4”; 1"; 1"1/4; 1"1/2; 2" 221PB - Blue - RTS M/F Flat handle 1/4"; 3/8”; 1/2”; 3/4”; 1"; 1"1/4; 1"1/2; 2" 224 - RTS M/F butterfly handle 3/8”; 1/2”; 3/4”; 1" 224PB - Blue - RTS M/F butterfly handle 3/8”; 1/2”; 3/4”; 1" 253 - RTS M/F flat handle with extension 1/2”; 3/4”; 1"; 1"1/4; 1"1/2; 2" 222 - RTS M/M Flat handle 3/8”; 1/2”; 3/4”; 1"; 1"1/4; 1"1/2; 2" 222PB - Blue - RTS M/M Flat handle 3/8”; 1/2”; 3/4”; 1"; 1"1/4; 1"1/2; 2" 225 - RTS M/M butterfly handle 3/8”; 1/2”; 3/4”; 1" 225PB - Blue - RTS M/M butterfly handle 3/8”; 1/2”; 3/4”; 1" 236 - MINI VALVE F/F 1/8”; 1/4”; 3/8”; 1/2”; 3/4" 237 - MINI VALVE M/F 1/8”; 1/4”; 3/8”; 1/2”; 3/4" 238 - MINI VALVE M/M 1/8”; 1/4”; 3/8”; 1/2”; 3/4" 251 - RTS STRAIGHT M/F with union fitting 1/2”; 3/4”; 1”. 257 - RTS WITH DECOMPRESSION F/F flat handle 3/8”; 1/2”; 3/4”; 1" 256 - Nickel-plated brass “Y” ball valve, FFF 3/4" x 1/2" x 1/2”; 1" x 3/4" x 3/4" 261 - RTS WITH SIEVE FILTER - butterfly handle 1/2”; 3/4" 298 - Square ball valve with union connection 1/2”; 3/4”; 1" 235R - Red - Ball valve, M/F, with free nut 1/2”; 3/4 235B - Blue - Ball valve, M/F, with free nut 1/2”; 3/4 239 - Mini ball valve in raw brass, MF, with nut 1/2" 240 - Ball valve before/after brass counter, FF 1/2" x 3/4”; 3/4" x 3/4" 242 - Ball valve before/after brass counter, MF 1/2" x 3/4”; 3/4" x 3/4”; 3/4" x 1" 246 - Bleed ball valve before/after meter in brass MF 1/2" x 3/4”; 3/4" x 3/4”; 1" x 3/4”; 1" x 1" 241 - Ball valve before/after brass counter, FF 1/2" x 3/4”; 3/4" x 3/4" 243 - Brass before/after meter ball valve, MF 1/2" x 3/4”; 3/4" x 3/4" 245 - Red - Brass before/after meter ball valve, MF 1/2" x 1/2”; 1/2" x 3/4”; 3/4" x 3/4" 244 - Square ball valve before/after meter in brass MF 1/2" x 3/4”; 3/4" x 3/4" SMART Series 120 - BALL VALVE F/F flat handle 3/8”; 1/2”; 3/4”; 1"; 1"1/4; 1"1/2; 2"; 2"1/2; 3”; 4" 120PB - Blue - BALL VALVE F/F flat handle 3/8”; 1/2”; 3/4”; 1"; 1"1/4; 1"1/2; 2"; 2"1/2; 3”; 4" 123 - BALL VALVE F/F butterfly handle 3/8”; 1/2”; 3/4”; 1" 121 - BALL VALVE M/F flat handle 3/8”; 1/2”; 3/4”; 1"; 1"1/4; 1"1/2; 2" 121PB - Blue - BALL VALVE M/F flat handle 3/8”; 1/2”; 3/4”; 1"; 1"1/4; 1"1/2; 2" 124 - BALL VALVE M/F butterfly handle 3/8”; 1/2”; 3/4”; 1" 122 - BALL VALVE M/M flat handle 3/8”; 1/2”; 3/4”; 1" 122PB - Blue - BALL VALVE M/M flat handle 3/8”; 1/2”; 3/4”; 1" 125 - BALL VALVE M/M butterfly handle 3/8”; 1/2”; 3/4”; 1" 126 - F/F Drain valve flat handle 1/2”; 3/4" 130 - M/M Drain valve flat handle 1/2”; 3/4"

Approval Holder:

EZFITT

Company Name

EZFITT

Address

ZI Nord - 281 Avenue Pierre et Marie Curie 13340 ROGNAC

Country

France

View All Listings by this Company