‘Maincor’ range of pipe adaptors and ‘Multi-Fit’ straight connectors (brass bodies) for use with ‘Maincor PERT/Al/PERT MLC’ pipe. 12mm pipe and fittings have a maximum working pressure of 6.0 bar. 16mm & 20mm pipe and fittings have a maximum working pressure of 10.0 bar Maximum operating temperature 95°C
‘Numepress’ range of stainless-steel crimp fittings incorporating EPDM and ‘O’-rings. For use with stainless steel tube. Maximum working pressure 16.0 bar. Maximum operating temperature 95°C.
‘Epsilon Series’ polypropylene bodied compression fittings with EPDM ‘O’-rings for use with Elysee PE80 blue pipes. The fittings are supplied with a pipe liner. Above and below ground use. Maximum working pressure 12.5 bar. Cold water use only.
Range of copper solder ring fittings for use with copper tube. For above ground use only. Maximum working pressure 25.0 bar. Maximum operating temperature 99°C.
Range of copper end feed fittings for use with copper tube. For above and below ground use. Maximum working pressure 25.0 bar. Maximum operating temperature 99°C.
Dual flush, WC outlet valves. Model A2706 is operated via a push button assembly for either full or reduced flush. Models A2415L & A2415M are not supplied with a operating button. Maximum operating temperature. Cold water use only.
Range of dual flush, WC outlet valves. The valves are operated via a push button assembly for either full or reduced flush. Cold water use only
Range of waste water heat recovery systems incorporating a twin wall copper coil (iZi models) or stainless steel (PiPe models). Maximum working pressure 10.0 bar. Cold water use only.
Range of indirect heat interface units with copper brazed stainless-steel heat exchangers, providing heating and instantaneous hot water. The products incorporate an expansion vessel on the cold-water supply to the plate heat exchanger and a safety relief valve on the space heating circuit set @ 3.0 bar. The domestic hot water and space heating circuit are both fitted with drain valves incorporating cover caps. Maximum working pressures: Domestic hot water 10.0 bar. Space Heating 2.5 bar. District Heating 3.0 bar. Maximum operating temperature 85˚C.
Range of gas fired water heaters incorporating stainless steel strainers on the inlets. Maximum working pressure 10.0 Bar Maximum working temperature 85˚C
Range of wall mounted combination boilers providing domestic hot water via a plate heat exchanger and pressurised central heating system, incorporating a pressure relief valve set at 3.0 bar and expansion vessel on the primary circuit. The inlet of the replenishing valve between the primary and secondary circuits incorporate a plastic strainer. Maximum working pressure 2.5 bar (primary) and 6.0 bar (secondary). Maximum operating temperature 85˚C.
Range of flow sensors with brass bodies. Maximum working pressure 16.0 bar. Maximum operating temperature 90°C
Range of isolation valves incorporating brass bodies and EPDM ‘O’-rings. Maximum working pressure 5.0 bar. Maximum operating temperature 60°C.
Range of inline circulating pumps with bronze bodies, plastic impeller and EPDM rubber seals. Maximum working pressure 10.0 bar. Maximum operating temperature 100°C.
Dutypoint ‘VS’ range of cold water supply booster sets, incorporating 2 to 8 pumps with a modular stainless steel manifold system. The booster sets also incorporate spherical valves, non-return valves, pressure switches/sensors and expansion vessels.. Maximum working pressure 10.0 bar. Cold water use only.
Range of positive displacement diaphragm pumps with plastic bodies, EPDM ‘O’-rings and TPE diaphragm. The product incorporates an integral bypass relief valve. For use with John Guest LLDPE Pipe. Maximum working pressure 11.03 Bar (Bypass) and 7.0 Bar (Operating).
Range of overhead shower outlets with chromium plated plastic bodies. Models SD1062 and SD1064 incorporate stainless steel strainers in the inlets. Maximum working temperature 75°C.
A self-closing shower handset with a plastic body, the inlet incorporates a plastic flow restrictor and an approved check valve cartridge, however, the complete product has not been fully tested to demonstrate it provides backflow protection. Maximum working pressure 6.0 bar. Maximum operating temperature 85 °C.
Range of shower handsets with chromium plated plastic bodies. Maximum operating temperature 75°C.
Shower handset incorporating a chromium plated plastic body. Maximum operating temperature 65°C.
Range of shower outlets with chromium plated bodies. Models P60901 and P61400 have check valves fitted at the inlets however, the complete products have not been fully tested to demonstrate they provide backflow prevention. From July 2023, model P61400 can also be supplied without the check valve at the inlet. Maximum operating temperature 70°C.
Shower handset (various finishes) with built in flow restrictor. Maximum operating temperature 60°C.
Shower hose incorporating an EPDM liner and grey PET outer layer. Supplied with EPDM washers. Maximum operating temperature 70°C.
Range of shower handsets with a chrome plated body. Maximum operating temperature 60°C.
PVC lined, chrome plated shower hose. Maximum operating temperature 60°C.
Range of shower outlets with chromium plated bodies. Models P60901 and P61400 have check valves fitted at the inlets however, the complete products have not been fully tested to demonstrate they provide backflow prevention. Maximum operating temperature 70°C. Open outlet use only.
Wall mounted shower intake, having a brass body (chrome plated). The outlet incorporates a single check valve cartridge (however the complete assembly has not been tested to demonstrate it provides adequate backflow protection) Maximum working pressure 5.0 bar. Maximum operating temperature 60°C.
In-line, Y-patterned strainer with stainless steel body and EPDM ‘O’-ring. Maximum working pressure 16.0 bar. Maximum operating temperature 100°C.
Range of in-line “Y” patterned strainers with brass bodies incoroporating NBR ‘O’-rings and stainless steel filters. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.
Range of pillar taps (chrome plated brass) with non-rising spindle headworks and cross type operating members. The spout outlets incorporate a plastic flow straightener and the products are supplied with metal backnuts. Maximum working pressure 5.0 bar. Maximum operating temperature 60°C.
Range of pillar taps (chrome plated brass) incorporating non-rising spindle headwork with cross type operating members. The spout outlet incorporates a plastic flow straightener. The product is supplied with metal backnuts. Maximum working pressure 7.0 bar. Maximum operating temperature 60°C.
Range of stainless steel or ACB braided, PE-RT lined flexible hose assemblies, incorporating various end connections. The 15mm & 22mm compression models may incorporate an isolation valve. The 15mm pushfit incorporates an isolation valve. Models added April 2022 have a maximum operating pressure of 6.0 bar, a maximum operating temperature of 65°C and are for use with copper pipe manufactured to BS EN 1057. All other models have a maximum operating pressure of 10.0 bar and a maximum operating temperature of 85°C
Range of vertical cased and insulated direct and indirect unvented stainless steel hot water storage cylinders. The storage cylinders incorporate an internal air bubble to accommodate the expansion of hot water. The DHW circuit has a factory fitted temperature and pressure relief valve set at 10.0@90˚C. The inlet control group includes a pressure reducing valve set at 3.0 bar, single check valve cartridge (verified by test and suitable for backflow protection against Fluid Category 2) and a expansion valve set at 8.0 bar. The products are supplied with a tundish and a motorised valve to be installed on the primary indirect circuit. Maximum supply pressure to the pressure reducing valve is 12.0 bar. Maximum working pressure of primary circuit is 6.0 bar. Maximum secondary circuit is 9.5 bar. Maximum operating temperature 85°C.
Range of wall mounted bar type thermostatic shower mixers (chromium plated brass) incorporating a ceramic disc headworks controlling the flow. Temperature is controlled via a thermostatic cartridge with single lever type operating members which incorporate manual override buttons. The inlets incorporate a stainless-steel strainer and an approved check valve cartridge; however, the complete products have not been fully tested to demonstrate that they provide backflow protection. Products are supplied with a shower hose, shower handset, riser rail and soap dish. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.
Wall mounted, concealed, thermostatic shower valve with brass body, incorporating half turn ceramic disc headworks controlling and diverting the flow, the temperature is controlled independently via a thermostatic cartridge, with dome type operating members. The inlets incorporate a stainless-steel strainer and an approved check valve cartridge; however, the complete products have not been fully tested to demonstrate that they provide backflow protection. Products are supplied with a shower hose, shower handset, riser rail and overhead shower. Maximum working pressure 5.0 bar. Maximum operating temperature 80°C.
Wall mounted, concealed, thermostatic shower valve with brass body. Incorporating a quarter turn ceramic disc headwork which controls the flow, temperature is controlled independently via a thermostatic cartridge with cube type operating members. The inlets incorporate a stainless-steel strainer and an approved check valve cartridge; however, the complete products have not been fully tested to demonstrate that they provide backflow protection. Products are supplied with a shower hose, shower handset and riser rail. Maximum working pressure 5.0 bar. Maximum operating temperature 80°C.
Wall mounted, concealed, thermostatic shower valve with brass body, incorporating half turn ceramic disc headworks controlling and diverting the flow, the temperature is controlled independently via a thermostatic cartridge, with single lever operating members. The inlets incorporate a stainless-steel strainer and an approved check valve cartridge; however, the complete products have not been fully tested to demonstrate that they provide backflow protection. Products are supplied with a shower hose, shower handset, riser rail and overhead shower. Maximum working pressure 5.0 bar. Maximum operating temperature 80°C.
Wall mounted, concealed, thermostatic shower valve with brass body. Incorporating a quarter turn ceramic disc headwork which controls the flow, temperature is controlled independently via a thermostatic cartridge with lever type operating members. The inlets incorporate a stainless-steel strainer and an approved check valve cartridge; however, the complete products have not been fully tested to demonstrate that they provide backflow protection. Products are supplied with a shower hose, shower handset and riser rail. Maximum working pressure 5.0 bar. Maximum operating temperature 80°C.
Wall mounted bar type thermostatic shower valve (chromium plated brass) incorporating quarter turn ceramic disc headwork controlling the flow with dome type operating members. The temperature is controlled independently via a thermostatic cartridge with single lever type operating member and manual override button. Both inlets incorporate stainless steel strainers and an approved single check valve cartridge however, the complete product has not been fully tested to demonstrate it provides backflow protection. Supplied with shower hose and handset. Maximum working pressure 5.0 bar. Maximum operating temperature 60°C.
Wall mounted thermostatic mixing valves (chromium plated brass), flow is controlled via a quarter turn ceramic disc headwork with dome type operating members. The temperature is controlled by a thermostatic cartridge with dome type operating members which incorporate a manual override button. The inlets incorporate a stainless-steel strainer and an approved check valve cartridge; however, the complete products have not been fully tested to demonstrate that they provide backflow protection. Products are supplied with a shower hose, shower handset and riser rail. Maximum working pressure 5.0 bar. Maximum operating temperature 65°C.
Range of thermostatic mixing valves incorporating brass bodies (various finishes). Flow is controlled via a detent headworks and depending on model can be either a 2 or 3 headwork option supplying shower or bath outlets. The temperature is controlled independently via a thermostatic cartridge. Inlets incorporate a plastic strainer and a single check valve cartridge (however the complete unit has not been tested to demonstrate it provides adequate backflow protection). Maximum working pressure 5.0 bar. Maximum operating temperature 60°C.
Range of ‘right hand’ or ‘left hand’ tempering valves having a plastic body incorporating a thermostatic element. The cold inlet incorporates a single check valve cartridge, however the complete product has not been fully tested to demonstrate it provides backflow protection Maximum working pressure 3.0 bar. Maximum operating temperature 60°C.
Range of wafer, lugged and flanged butterfly valves incorporating blue epoxy coated ductile iron bodies, EPDM seats and DI-FBE nylon coated stainless steel discs. Maximum working pressure 16.0 bar. Cold water uses only.
Range of ceramic disc diverter valve headworks with plastic bodies for use in specifically dimensioned bodies. Maximum working pressure 10.0 bar. Maximum operating temperature 85°C.
Range of ‘J2 10 series’ of equilibrium float valves with cast iron (epoxy coated) bodies and EPDM seals. Available with either standard or extended arms. Maximum working pressure 10 bar. Cold water use only.
Range of equilibrium float operated valves with a stainless steel body and float (chrome plated), and a silicone seat. Maximum operating pressure 10.0 bar. Cold water use only.
Range of in-line adjustable pressure reducing valves, with DZR brass bodies and EPDM seat washers & ‘o’ rings and stainless-steel filters. Maximum inlet supply pressure 16.0 bar. Outlet pressure range: 0.8-6.0 bar. Maximum operating temperature 80°C.
Range of pilot operated pressure reducing valves with blue epoxy coated ductile iron bodies, stainless steel filter, EPDM ‘O’-rings and diaphragm. The valve has an adjustable pressure reducing facility controlled via a pilot valve, with auxiliary components including stainless steel tubing and fittings, and stainless-steel spherical valves. Maximum inlet supply pressure 16.0 bar. Outlet pressure setting is adjustable in the range of 0.6 - 6.0 bar. Maximum operating temperature 50°C.
Range of pilot operated pressure reducing valves with blue epoxy coated ductile iron bodies, stainless steel filter, EPDM ‘O’-rings and diaphragm. The valve has an adjustable pressure reducing facility controlled via a pilot valve, with auxiliary components including stainless steel tubing and fittings, and stainless steel spherical valves. Maximum inlet supply pressure 16.0 bar. Outlet pressure setting is adjustable in the range of 0.6 - 6.0 bar. Maximum operating temperature 50°C.
Ranges of solenoid valves with brass bodies and EPDM diaphragms. Maximum working pressure is 10.0 bar Maximum operating temperature 85°C.
Page 14 of 227
We use cookies to give you the best possible experience with WRAS. Some are essential to provide website functions and ensure the website is secure. We also use cookies to help us understand how people use the site and to make improvements. Click "Accept All" to enable recommended settings or click "Manage cookies" to adjust your settings. For more details, see our Cookie Policy.
