'GIRPI HTA Fusion'. Site applied, orange coloured solvent cement, intended to join plastic pipe and fittings. Apply as per manufacturer instructions '6311289/20'. Cure for 24 hours@7°C. For use with water up to 70°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'ACRYSTEX® PM-600'. Transparent, injection moulded Methyl Methacrylate-Styrene Copolymer (MS or SMMA) material. For use with water up to 85°C.
Floor mounted, single hole, single outlet (fixed) combination tap assembly (brass bodies - in various finishes), incorporating a ceramic cartridge headwork with a single lever operating member, a manual diverter to shower outlet and a waterfall type spout. Shower hose and handset is not supplied with this product. Maximum working pressure 10.0bar. Maximum operating temperature 60°C.
Floor mounted, single hole, single outlet (swivel) combination tap assembly (brass bodies - in various finishes), incorporating a ceramic cartridge headwork with a single lever operating member and a lockable diverter to shower outlet. The spout outlet incorporates a plastic aerator. The product is supplied with a shower hose and handset. Maximum working Pressure 10 bar. Maximum operating Temperature 60 °C
Deck mounted single hole, single outlet (fixed) electronically controlled tap assemblies (chromium plated brass). The flow is controlled by a solenoid valve actuated via an infra-red sensor. Temperature is manually blended using a single lever operating member. The spout outlets incorporate plastic aerators. The inlets incorporate approved check valve cartridges, however, the complete assembly has not been fully tested to demonstrate that it provides backflow protection and stainless-steel strainers. Maximum operating pressure 8.0 bar. Maximum operating temperature 65°C.
Range of single hole, single outlet (fixed) electronically controlled, tap assemblies (chromium plated brass). The flow is controlled via solenoid valves, actuated by infra-red sensors. Temperature is manually blended using a single lever operating member. The spout outlets incorporate plastic aerators. The inlet hoses incorporate stainless steel strainers and approved check valve cartridges, however, the complete product has not been fully tested to demonstrate it provides backflow protection and stainless steel strainers. Maximum operating pressure 8.0 bar. Maximum operating temperature 65°C.
Range of deck mounted, electronically operated tap assemblies (chromium plated brass). The flow is controlled by a solenoid valve and actuated via an infra-red sensor. The spout outlet incorporates a plastic aerator. The inlet hose connection incorporates a stainless-steel strainer. Maximum operating pressure 8.0 bar. Maximum operating temperature 65°C.
Range of single hole, single outlet electronically controlled tap assemblies (chromium plated brass). Flow is controlled using a solenoid valve and actuated via the infrared sensor. The spouts incorporate a plastic aerator. Maximum working pressure 8.0 Bar. Maximum operating temperature 65.0°C
Range of single hole, single outlet electronically controlled tap assemblies (chromium plated brass), incorporating a solenoid valve controlling the flow which is actuated via infrared sensor. The spouts incorporate plastic aerators. Maximum working pressure 8.0 Bar. Maximum operating temperature 65.0°C
Range of single hole, single outlet electronically controlled tap assemblies (chromium plated brass). Flow is controlled using a solenoid valve and actuated via the infrared sensor. The spouts incorporate a plastic aerator. Maximum operating pressure 8.0 bar. Maximum operating temperature 65°C.
Range of BS1212-4 (2016) float operated valves for WC flushing cisterns, bottom or side entry type with plastic or brass ½’’ BSP inlet. The inlet incorporates a strainer, Compact models incorporate a delay fill function. Maximum working pressure 10.0 bar. For use with cold water only.
Range of concealed WC dual flushing cisterns with a vertical BS 1212-4(2016) float operated inlet valve providing a Type AG air gap arrangement and a dual flush outlet valve. The flush volume is operated by a two-push button assembly. The product also incorporates a servicing valve and flexible hose on the inlet supply. Maximum working pressure 10 Bar, cold water use only.
Three-hole, single outlet (fixed), combination tap assembly (brass body – various finishes), incorporating a ceramic cartridge headwork with a single lever operating member and a manual diverter to the shower outlet. The product is supplied with a stainless-steel braided EPDM lined flexible connection hose to connect the head work to the spout outlet. Maximum working pressure 5.0 Bar
Non-metallic materials and components comply with BS6920 at 65°C
Range of quarter turn ceramic disc headworks with brass bodies and EPDM O rings. For insertion into specifically dimensioned bores. Maximum working pressure 5.0 bar. Maximum operating temperature 60°C.
Range of ceramic disc headworks with brass bodies incorporating NBR O-rings. For insertion into specifically dimensioned tap assemblies. Maximum working pressure 10 Bar Maximum operating temperature 85°C
Range of thermostatic cartridges with either plastic or brass bodies (see model) and stainless-steel filters (except model ZL-FX-LFXTS45). For insertion into specifically dimensioned bores. Maximum working pressure 6.0 bar. Maximum operating temperature 75°C.
Single hole single outlet (swivel) pull down spray combination tap assemblies (brass bodies – various finishes) incorporating a ceramic cartridge headworks and single lever operating members. The spout outlet incorporates a plastic aerator. Maximum working pressure 10.0 bar. Maximum operating temperature 65°C.
Single hole, single outlet (swivel) combination tap assemblies with (brass bodies -various finishes) incorporating ceramic cartridge headworks with single lever operating members. The spout outlet incorporates a plastic aerator and a pull out spray. The connection between the outlet and the hose incorporates an approved single check valve cartridge, however, the complete product has not been fully tested to demonstrate that it provides backflow protection. Maximum working pressure 10.0 Bar Maximum operating temperature 65.0°C
Range of deck mounted single hole, single outlet (fixed) combination tap assemblies (chromium plated brass). Incorporating ceramic cartridge headwork, and single lever operating member. The spout outlet incorporates a plastic flow straightener and supplied with a flow regulator. Model 23.112 is supplied with a lever type pop-up waste (not tested). Maximum working pressure 10 bar. Maximum working temperature 60°C
Range of single hole, single outlet (fixed) combination tap assemblies (chromium plated brass bodies), incorporating a ceramic cartridge headwork with a single lever operating member. The spout outlet incorporates a plastic aerator. Maximum working pressure 10.0 Bar. Maximum operating temperature 65°C.
Single hole, single outlet, (fixed), combination tap assembly (chrome plated brass body), incorporating a ceramic cartridge headwork with a single lever operating member. The spout outlet incorporates a plastic aerator. Maximum operating pressure 10.0 bar. Maximum operating temperature 60°C.
Range of single-hole, single outlet fixed combination tap assemblies (brass bodies – various finishes), incorporating a ceramic cartridge headwork with single lever operating members. The spout outlets incorporate plastic aerators. The product is supplied with a click-type waste (verified by test). Maximum operating pressure 10.0 bar. Maximum operating temperature 60°C.
Range of single hole, single outlet (fixed) combination tap assemblies (brass bodies – various finishes), incorporating a ceramic cartridge headwork with single lever operating members. The spout outlets incorporate a plastic aerator. Maximum working pressure 5.0 bar. Maximum operating temperature 60°C.
Range of single hole, single outlet (fixed) combination tap assemblies (chromium plated brass) incorporating ceramic cartridge headworks and single lever operating members. The spout outlet incorporates a plastic aerator. Model 33526626 is supplied with a lever type pop-up waste. Maximum working pressure 10.0 Bar. Maximum operating temperature 60.0°C.
Range of single hole, single outlet (fixed), combination tap assemblies incorporating, (chrome plated brass bodies),with single lever operating members. The spout outlet incorporates a plastic flow straightener. Some products are supplied with a lever operated pop-up waste (not verified by test). Maximum working pressure 10.0 bar. Maximum operating temperature 65°C.
Range of single hole, single outlet (fixed) combination tap assemblies (brass bodies - various finishes), incorporating ceramic cartridge headworks with single lever operating members. The spout outlets incorporate plastic aerators. Maximum working pressure 3.5 Bar. Maximum operating temperature 60.0°C.
Range of single hole, single outlet (fixed) combination tap assemblies (brass bodies - various finishes), incorporating ceramic cartridge headworks with single lever operating members. The spout outlet incorporates a waterfall type outlet. The inlets incorporate plastic flow regulators. Maximum working pressure 3.5 Bar. Maximum operating temperature 60.0°C
Floor mounted single hole, single outlet (fixed) combination tap assembly with brass body (chrome plated), incorporating a ceramic cartridge headwork with single lever operating member and a self-cancelling diverter to shower outlet. Supplied with hose and handset. Maximum working pressure 10.0 Bar. Maximum operating temperature 60.0°C.
A range of single-hole single outlet swivel combination tap assemblies with brass bodies (chromium plated). Incorporating ceramic cartridge headworks with various operating members. The spout outlets on some models incorporate a plastic aerator. Maximum working pressure - 10 bar. Maximum operating temperature - 60°C.
Range of single-hole, single outlet (swivel) combination tap assemblies (brass bodies - various finishes), incorporating quarter turn ceramic disk headworks with single lever operating members. The spout outlet incorporates a plastic aerator. The products are supplied with a surface mounting kit incorporating EPDM lined flexible hose assemblies with ½” captive nut and 15mm compression isolation valves that incorporate single check valve assembly (suitable for backflow protection against fluid category 2). Maximum working pressure 10.0 bar. Maximum operating temperature 65°C
Range of single-hole, single outlet (swivel) combination tap assemblies (brass bodies - various finishes), incorporating quarter turn ceramic disk headworks with single lever operating members. The spout outlet incorporates a plastic aerator. The products are supplied with a surface mounting kit incorporating EPDM lined flexible hose assemblies with ½” captive nut and 15mm compression isolation valves that incorporate single check valve assembly (suitable for backflow protection against fluid category 2). Maximum working pressure 10.0 bar. Maximum operating temperature 65°C
Range of single-hole, single outlet (swivel) combination tap assemblies (brass bodies - various finishes), incorporating ceramic cartridge headworks with single lever operating members. The spout outlet incorporates a plastic aerator. The products are supplied with a surface mounting kit incorporating EPDM lined flexible hose assemblies with ½” captive nut and 15mm compression isolation valves that incorporate single check valve assembly (suitable for backflow protection against fluid category 2). Maximum working pressure 10 bar. Maximum operating temperature 65°C
Range of single-hole, single outlet (swivel) combination tap assemblies (brass bodies - various finishes), incorporating ceramic cartridge headworks with single lever operating members. The spout outlet incorporates a plastic aerator. The products are supplied with a surface mounting kit incorporating EPDM lined flexible hose assemblies with ½” captive nut and 15mm compression isolation valves that incorporate single check valve assembly (suitable for backflow protection against fluid category 2). Maximum working pressure 10 bar. Maximum operating temperature 65°C
Range of single-hole, single outlet (swivel) combination tap assemblies (brass bodies - various finishes), incorporating ceramic cartridge headworks with single lever operating members. The spout outlet incorporates a plastic aerator. The products are supplied with a surface mounting kit incorporating EPDM lined flexible hose assemblies with ½” captive nut and 15mm compression isolation valves that incorporate single check valve assembly (suitable for backflow protection against fluid category 2). Maximum working pressure 10.0 bar. Maximum operating temperature 65°C
Single hole, single outlet (swivel) combination tap assembly (chromium plated brass) incorporating quarter turn ceramic disc headworks with single lever operating members. The spout outlet incorporates a plastic flow straightener. The product is supplied with an optional plastic aerator. Maximum working pressure 6.0 bar. Maximum operating temperature 65°C.
Single hole, single outlet (swivel) combination tap assembly (chromium plated brass) incorporating quarter turn ceramic disc headworks with single lever operating members. The spout outlet incorporates a plastic aerator. The product is supplied with an optional plastic flow straightener. Maximum working pressure 6.0 bar. Maximum operating temperature 65°C.
Range of single hole, single outlet (swivel) combination tap assemblies (brass bodies - various finishes), incorporating quarter turn ceramic disc headworks with a single lever operating member. The spout outlet incorporates a plastic aerator. Maximum working pressure 10.0 bar. Maximum operating temperature 65°C.
Range of single hole, single outlet (swivel) combination tap assemblies (brass bodies - various finishes) incorporating quarter turn ceramic disc headworks with single lever operating members. The spout outlets incorporate a plastic aerator or a plastic flow straightener. Maximum working pressure 10.0 Bar. Maximum operating temperature 65°C.operating temperature 60°C.
Floor mounted, single hole, single outlet (swivel) combination tap assembly (chromium plated brass) incorporating a quarter turn ceramic cartridge headwork with single lever type operating member. The spout outlet incorporates a plastic aerator. Maximum working pressure 10.0 Bar. Maximum operating temperature 60.0°C.
Range of single hole, single outlet (swivel) combination tap assemblies incorporating quarter turn ceramic disc headworks with single lever operating members. The spout outlet incorporates a plastic aerator. Maximum working pressure 5.5 bar. Maximum operating temperature 60°C
Two hole, single outlet (fixed) combination tap assembly with brass body, incorporating quarter turn ceramic disc headworks with either single lever or cross top operating members. The spout outlet incorporates a plastic aireator. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.
Range of wall mounted, two-hole, single outlet (fixed) combination tap assemblies, incorporating a ceramic cartridge headwork with a single lever operating member. The spout outlet incorporates a plastic aerator. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.
Two-hole, single outlet (fixed) combination tap assembly (chromium plated brass), incorporating quarter turn ceramic disc headworks with single lever operating members. The spout outlet incorporates a plastic flow straightener. The product is supplied with metal backnuts. Maximum working pressure 5.0 bar. Maximum operating temperature 60°C.
Range of two-hole, single outlet (fixed) combination tap assemblies (chrome plated brass) incorporating quarter turn ceramic disc headworks with single lever operating members. The spout outlets incorporate plastic flow straighteners. Some models incorporate open outlet or waterfall spouts. The products are supplied with metal back nuts. Maximum working pressure 10.0 Bar. Maximum operating temperature 60.0°C.
Wall mounted, concealed, two hole, single outlet (fixed) combination tap assembly (chromium plated or black finish brass) incorporating a ceramic cartridge headwork with a single lever operating member. The spout outlet incorporates a plastic aerator. Maximum working pressure 10.0 bar. Maximum operating temperature 65°C.
Range of two-hole, single outlet (fixed) combination taps assemblies (brass bodies – various finishes), incorporating quarter turn ceramic disc headworks with single lever operating members. Models (HB4001737) incorporate A plastic flow straightener at the spout outlet. Models (HB4003738) incorporate a waterfall outlet. The inlets incorporate a plastic flow regulator and metal back nuts. Maximum working pressure 3.5 Bar. Maximum operating temperature 60.0°C.
Floor mounted two hole, single outlet (swivel) combination tap assembly (chromium plated brass). Incorporating a quarter turn ceramic disc headwork with either a single lever (25943819 model) or cross top (25943809 model) operating members and a manually operated diverter to shower outlet. The outlet connection to the shower hose and the inlet of the shower handset each incorporate a single check valve cartridge, however, the complete product has not been fully tested to demonstrate it provides backflow protection. The spout outlet incorporates a plastic aerator. The products are supplied with shower hose and handset. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.
Two hole, single outlet (fixed) combination tap assembly (chromium plated brass), incorporating quarter turn ceramic disc headworks with single lever operating members and a manually operated diverter to shower outlet. The spout outlet incorporates a plastic aerator. Maximum working pressure - 10 Bar. Maximum operating temperature - 60 °C.
Range of two-hole, single outlet (swivel) combination tap assemblies, (chrome plated brass bodies), incorporating quarter turn ceramic disc headworks with single lever operating members. The spout outlet incorporates a stainless steel filter washer and plastic flow straightener. The products are supplied with metal back nuts. Maximum working pressure 10.0 bar. Maximum operating temperature 65°C.
Range of two hole, single outlet (swivel) combination tap assemblies (brass bodies, various finishes - see model), incorporating quarter turn ceramic disc headworks with either cross top, dome type or single lever operating members (see model). The spout outlet, excluding the F6134 & F6144 models, incorporates a plastic aerator. The products are supplied with metal backnuts. Maximum operating pressure 10.0 bar. Maximum operating temperature 60°C.
Page 108 of 171
We use cookies to give you the best possible experience with WRAS. Some are essential to provide website functions and ensure the website is secure. We also use cookies to help us understand how people use the site and to make improvements. Click "Accept All" to enable recommended settings or click "Manage cookies" to adjust your settings. For more details, see our Cookie Policy.
