Electrolytic and magnetic scale inhibitors incorporating copper or nickel coated copper bodies. Compression models are to be used with copper pipe manufactured to BS EN1057. Maximum working pressure 10.0 bar. Cold water use only.
Range of UV disinfection units with stainless steel bodies and quartz tubes. Maximum working pressure 10.0 bar. Cold water use only.
Smart water monitor with plastic housing, integrated motorised shut off valve, ultrasonic transducer and pressure sensor. Maximum working pressure 10.0 bar. Maximum operating temperature 85°C.
Non-metallic materials and components comply with BS6920 at 85°C
'Tufbon PTS600, PTS888 & CG100'. Black coloured, sintered, carbon graphite sealing rings. For use with water up to 85°C.
'SJP-F15C Ring'. Dark grey coloured Graphite Loaded Sintered Silicon Carbide ring made by pressing, lathing, sintering, grinding then lapping. For use with water up to 85°C.
‘KUBOTA SEAL AC’. Factory applied, colourless acrylic resin coating. Apply as per manufacturer’s instructions ‘ref. no. 65700H-2.3’ dated 'Mar. 14.2017'. Cure for 7 days@27°C. For use with water up to 60°C. This material is only approved for the curing conditions that appear on the approval. If the curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
‘V-PET#1600 Gray F’. Factory applied, dark grey coloured epoxy resin powder coating. Apply as per manufacturer’s instructions ‘ref.no. VP1600-PD-170412’, dated '12th April 2017'. Cure for 10 minutes@200°C. For use with water up to 60°C. This material is only approved for the curing conditions that appear on the approval. If the curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'5013 High chlorinated polyethylene anticorrosive coating'. Factory applied, blue coloured polyethylene coating. Apply as per manufacturer's TDS/IFU number '001', dated '2022.11.30'. Cure for 24 hours@23°C. For use with water up to 65°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
Factory applied, grey coloured blast furnace slag cements. ‘BFSC PAM MDN 1’. Mix water, sand, admixture & cement in a mass ratio of 0.33:2.35:0.0080:1 and apply as per manufacturer’s instructions ‘CE 7M’, dated ‘25/08/15’. Cure for 7 hours@70°C. For use with water up to 60°C. BFSC PAM GDN 1’. Mix water, sand, admixture & cement in a mass ratio of 0.33:2.84:0.0065:1 and apply as per manufacturer’s instructions ‘CE 8M/-3A’, dated ‘25/08/15’. Cure for 7 hours@70°C. For use with water up to 60°C. These materials are only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the materials are not covered by the scope of the approval.
'GCF-SRC'. Factory applied, grey coloured cement mortar. Mix sand, cement and water in a ratio of 4:2:1 and apply as per manufacturer's instructions 'QC-WI-8.1.8, revision 2/0, issue date 30/10/2021'. Cure for 28 days@24°C. For use with water up to 65°C. This material is only approved for the mixing & curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Titanseal 989'. Site applied, two-component, grey coloured (once mixed) polyurethane coating. Mix the grey coloured (opaque) base coating with the amber coloured hardener in a 3:1 volume ratio and apply Coat 1 as per manufacturer's application instructions dated '09.03.2018'. Cure for 4 hours@7°C. Mix and apply Coat 2 using the same mix ratio and application instructions and then cure for 14 days@7°C. For use with water up to 23°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the materials are not covered by the scope of the approval.
'Epilux QD DW Coating - Blue'. Factory applied, blue coloured, two-component epoxy coating. Mix Base and Catalyst in a 3:1 volume ratio and apply as per manufacturer's 'Product Information Data Sheet No: 780', 'Revision: 00', 'Issue Date Feb-22'. Cure for 7 days@30°C. For use with water up to 60°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Weberdry epo PW'. Site applied, light grey coloured (once mixed), two-component epoxy coating. Mix Part A (light grey coloured) with Part B (translucent, yellow coloured) in a weight ratio of 100:20. Apply as per manufacturer's TDS 'Edition: 04.23-A'. Cure for 24 hours@25°C. Mix and apply a second coat in the same way and then cure for 14 days@25°C. For use with water up to 23°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
`EcoZmart Waterproofing`. Site applied, grey coloured tanking slurry. Mix tanking slurry with water in a 3:1 volume ratio and apply coat 1 as per manufacturer's IFU 'TCOWP001', dated '26/05/2023'. Cure for 24 hours@7°C. Mix tanking slurry with water in a 3:1 volume ratio and apply coat 2, 24 hours after the first coat, as per manufacturer's IFU IFU 'TCOWP001', dated '26/05/2023'. Cure for 14 days@7°C. For use with water up to 23°C. This material is only approved for the mixing & curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Vinoleo 77/14'. Amber coloured, soap based lubricant. Apply as per manufacturer's instructions. For use with water up to 23°C.
'SURU Lubricant'. Yellow coloured lubricant. Apply as per manufacturer's instructions dated '18th Feb 2015'. For use with water up to 60°C.
‘RADISTRONG® AROMA RV400RKC2 106 NT, RV500RKC2 106 NT & RV600RKC2 106 NT’. ‘RADISTRONG® AROMA RV400RKC2 306 BK, RV500RKC2 306 BK & RV600RKC2 306 BK’. ‘RADISTRONG® AROMA RV300RKC2 106 NT’ & ‘RADISTRONG® AROMA RV300RKC2 306 BK’ were added to the approval in February 2024. Natural (indicated by NT - appear cream in colour) and black coloured (indicated by BK), injection moulded, glass fibre filled (between 30% & 60%), PA66 materials. For use with water up to 85°C.
‘Palaplast Hydropal W PE80 & PE100 pipes’. Extruded, PE80 & PE100 pipes, both available in either blue colour or black colour (with blue stripe). All pipes are for use with water up to 23°C.
‘Polypipe Black PE100 & Blue PE100 Pipes’. Black or blue coloured, extruded PE100 pipes. For use with water up to 23°C.
'FRIALEN Safety Fittings'. Black coloured, PE100 fittings which are injection moulded or machined from an extruded pipe. Between May 2023 and June 2025, the fittings were for use with water up to 23°C. Between July 2025 and May 2028, the black fittings are for use with water up to 60°C. Blue coloured PE100 fittings which are injection moulded. For use with water up to 23°C.
'PPE-2211 GF30 SAWyy-Gxxxx' (where yy-Gxxxx indicates and is replaced with a combination of numbers and letters). Off-white coloured, injection moulded PPE material. For use with water up to 85°C.
'DIC.PPS FZ-2140-F3 BLACK'. 'DIC.PPS FZ-2140-F3 BLACK-U' was added to the approval in September 2023. Black coloured, injection moulded PPS materials manufactured in Vienna, Austria. For use with water up to 85°C.
'DIC.PPS Z-230 BLACK' (manufactured in Komaki (Japan), Penang (Malaysia), Vienna (Austria) & Zhangjiagang (China). ‘DIC.PPS Z-230 BLACK-U’ (manufactured in Komaki (Japan), Penang (Malaysia), Vienna (Austria) & Zhangjiagang (China) was added to the approval in September 2023. ‘DIC.PPS Z-230 BLACK-U1’ (manufactured in Vienna (Austria) was added to the approval in September 2023. Black coloured, injection moulded PPS material. For use with water up to 85°C.
'Tefzel® ETFE 200, 207, 280, 750, HT2181, HT2183 & HT2185'. Un-pigmented (white coloured), compression moulded ETFE material. For use with water up to 85°C.
'Teflon® FEP 100 X, 100-J, 106 X, CJ 95 X, CJ 99 X & 9302 X'. Un-pigmented (white coloured, compression moulded FEP material. For use with water up to 85°C.
''Teflon® PFA 340 X, 345 X, 350 X, 350-T-J, 440 HP X, 445 HP X, 450 HP X & 416 HP X'. Unpigmented (white coloured), compression moulded PFA materials. For use with water up to 85°C.
'Teflon® PTFE 640XT X, 807N X, NXT 70, NXT 75, 6CN X, 62 X, 62N X, 62XT X, 669N X, 669 X, NXT 85, 605XT X, 6C X, 7A X, 641XT X & 650XT X’. White coloured, extruded or compression moulded PTFE material. For use with water up to 85°C.
'24410001 & 24410002'. White coloured, compression moulded PTFE materials. For use with water up to 85°C.
‘PVDF Solef 1010/0001’. White coloured, injection moulded PVDF material. For use with water up to 85°C.
'Titan A202'. Site applied, pale yellow coloured hydrophilic polyurethane foam. Apply as per manufacturer's Tech Sheet '03', dated '10.01.2023' and spray treated surface with water. Cure for 6 hours at an ambient temperature (19-21°C). For use with water up to 23°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'STATHEROS EPC80'. Site applied, grey coloured (once mixed), two-component anchor resin, supplied in a cartridge which automatically dispenses in a 1:1 ratio. Apply and cure as per manufacturer's product information 'Ver. 10' dated '02/06/23' (refer to working and loading times table for cure). For use with water up to 23°C. For use only as a resin anchor having been tested at a reduced surface area to volume ratio of 1,000mm² per 1 litre of water. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'E7001Z59 (EP02269PF) 2x modified'. Black coloured, compression moulded EPDM 'O' rings. Shore hardness 72 A. Tested in-radii sizes between 1.4mm & 1.8mm. For use with water up to 85°C.
‘CRIEP50 & CRIEP80’. Black coloured, compression moulded EPDM rubber materials. Shore hardness 50 & 80 respectively. Tested in-radius size 1.0mm. For use with water up to 70°C.
'EIW-54'. Black coloured, injection moulded EPDM material. Shore hardness 51 ShA. Tested in-radius size 0.5mm. For use with water up to 50°C.
'Liner Code 'W' (for Butterfly Valves R480/R481/R487 & R488)'. Black coloured, compression moulded EPDM material with a shore hardness of 70. Tested in-radius size 1.0mm. For use with water up to 23°C.
'Sunaflex T 8165'. Black coloured, compression moulded EPDM sheet material. Shore hardness 70. Tested in-radius size 1.0mm. For use with water up to 23°C.
'E134-B85-KTW-W270'. Black coloured, compression moulded EPDM material with a shore hardness of 88. Tested in-radius size 1.0mm. For use with water up to 23°C.
'HG02'. Black coloured, compression moulded EPDM sheet material. Shore hardness 75. Tested in-radius size 1.0mm. For use with water up to 85°C.
‘N5118F, N5518F, N6118F, N6518F, N7118F, N7008F, N7518F, N8118F, N8518F & N9118F’. Black coloured, compression moulded NBR rubber `O` rings and gaskets. Shore hardness between 50 & 90. 'O' rings have a tested in-radius size of between 0.25mm & 5.0 mm. Gaskets have a tested in-radius size of between 0.3mm & 7.5mm. For use with water up to 85°C.
'0612 HNBR'. Yellow coloured (opaque), injection moulded HNBR 'O' rings. Shore hardness 70. Tested in-radius size 1.31mm. For use with water up to 85°C.
‘SIL4008F, SIL4008F (N), SIL4008F (H), SIL4008F (R) & SIL4008F (BK). SIL4508F. SIL5008F, SIL5008F (H), SIL5008F (R) SIL5008F (BK), SIL5008F (B). SIL5508F. SIL6008F, SIL6008F (N), SIL6008F (H), SIL6008F (R), SIL6008F (BK). SIL6508F. S7008F, S7008F (N), S7008F (H), S7008F (R), S7008F (BK), SIL7118F, SIL7018F. SIL7508F. SIL8008F, SIL8008F (N), SIL8008F (H), SIL8008F (R), SIL8008F (BK)’. Range of compression moulded, silicone rubber `O` rings and gaskets available in natural, white, grey, blue, red, pale yellow, orange, green, brown and black colours. Shore hardness range 40 - 80. ‘O’ rings have an in-radius size range of 0.2mm – 5.0mm. Gaskets have an in-radius size range of 0.3mm – 7.5mm. For use with water up to 85°C.
‘SIL40X02, SIL45X02, SIL50X02, SIL55X02, SIL60X02, SIL65X02, SIL75X02 & SIL80X02’. Range of compression moulded, silicone rubber `O` rings and gaskets available in natural, white, grey, blue, red, pale yellow, orange, green, brown and black colours. Shore hardness range 40 - 80. ‘SIL70B02’ – Blue coloured. ‘SIL70W01’ – Natural. ‘SIL70R01’ – Red coloured. ‘SIL7001’ – Black coloured. Range of compression moulded, silicone rubber `O` rings and gaskets available in colours listed above. Shore hardness 70. ‘O’ rings have an in-radius size range of 0.2mm – 5.0mm. Gaskets have an in-radius size range of 0.3mm – 7.5mm. For use with water up to 85°C.
‘YH001 (natural) & YH002 (grey)’. Natural (appears white coloured) and grey coloured, compression moulded silicone rubber materials. Shore hardness 50. Tested in-radius size 1.0mm. For use with water up to 85°C.
'EMS Force 5543'. 'EMS Force 5543-P' was added to the approval in February 2025. Blue coloured pipe sealants. Apply as per manufacturer's instructions 'TLM.LB.07', version '0', issue date '07/03/2016'. Cure for 24 hours@23°C. For use with water up to 85°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'THAT RAPID BLU-STUFF'. 'THAT RAPID BLU-GEL' was added to the approval in February 2025. Blue coloured pipe sealants. Apply as per manufacturer's instructions 'TLM.LB.07', version '0', issue date '18/05/2023'. Cure for 24 hours@23°C. For use with water up to 85°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
Range of wall mounted, electronically operated, combination tap assemblies (stainless steel body, various finishes - see model), comprising of a Premix control unit and a spout. The flow is controlled by a solenoid valve, (Premix control unit), which is actuated via an infrared sensor. The central section of the valve incorporates a plastic strainer. Both inlets of the Premix control unit incorporate an approved single check valve cartridge, however the complete assembly has not been tested for backflow protection. The spout outlet incorporates a plastic aerator. Maximum working pressure 8.0 bar. Maximum operating temperature 60°C.
Non-metallic materials and components comply with BS6920 at 60°C
Bottom entry BS1212-4 (2016) compact type float operated valve for WC flushing cisterns. The inlet incorporates a flow restrictor. Maximum working pressure 10.0 bar. Cold water only
Side entry BS1212-4 (2016) compact type float operated valve for WC flushing cisterns. The inlet incorporates a flow restrictor. Maximum working pressure 10.0 bar. Cold water use only.
Range of basin bidet mixers with brass bodies, incorporating a ceramic cartridge headwork, and a single lever operating member. The spout incorporates a plastic aerator within a swivel nozzle. This product is supplied with a lever type pop up waste (not tested). Maximum working pressure 10.0 bar.
Non-metallic materials and components comply with BS6920 at 60°C
Range of ceramic cartridges or 2-way ceramic disc diverter headworks with plastic bodies, EPDM ‘O’-rings and/or gaskets, for insertion into specifically dimensioned bores. The JA01AJ and AH01AJ models incorporate a thermostatic element. Maximum working pressure 5.0 bar.
Non-metallic materials and components comply with BS6920 at 85°C
Page 94 of 204
We use cookies to give you the best possible experience with WRAS. Some are essential to provide website functions and ensure the website is secure. We also use cookies to help us understand how people use the site and to make improvements. Click "Accept All" to enable recommended settings or click "Manage cookies" to adjust your settings. For more details, see our Cookie Policy.
