'DR-PLAST HDPE PE-100 Pipes'. Black coloured (with dark blue stripe), extruded HDPE pipe. For use with water up to 60°C.
'DR-PLAST HDPE PE-100 Fittings'. Black coloured, HDPE fittings manufactured by either injection moulding or butt fusion welding. For use with water up to 60°C.
'CLH Hose'. Single layer, extruded, clear (transparent), LDPE hose. For use with water up to 70°C.
'Aura HDPE Electrofusion Fittings'. Black coloured, injection moulded HDPE (PE100) electrofusion fittings. For use with water up to 65°C.
'Eltex TUB124N2025'. Blue coloured, extruded polyethylene material. For use with water up to 23°C.
'Eltex PC002-50R968'. Light blue coloured, extruded polyethylene material. For use with water up to 23°C.
'Eltex Superstress TUB121N6000'. Black coloured, extruded polyethylene material. For use with water up to 23°C.
'Eltex TUB121'. Black coloured, extruded polyethylene material. For use with water up to 60°C.
'ELTEX Superstress TUB121N3000'. Black coloured, extruded polyethylene material. For use with water up to 23°C.
'BorSafe HE3490-LS'. Black coloured, extruded PE material. For use with water up to 60°C.
'Icorene 1314 BLK 9001'. Black coloured LLDPE material manufactured by rotomoulding. For use with water up to 85°C.
'RTP 0199 X 155521 Natural'. Natural (appears beige coloured), injection moulded polypropylene material. For use with water up to 50°C.
'Fluon G201'. Natural (appears white, opaque) extruded PTFE material. For use with water up to 85°C.
'TEADIT TF1590'. Pale orange coloured, PTFE material manufactured by mixing, calendaring, cutting and sintering. For use with water up to 85°C.
'Wrap & Seal'. Black coloured, extruded silicone rubber tape. Shore hardness 55. Tested in-radius size 0.25mm. For use with water up to 23°C.
'Dyna Stretch & Seal'. Black coloured, extruded silicone rubber tape. Shore hardness 55. Tested in-radius size 0.25mm. For use with water up to 23°C.
'STRONGHOLD SH-EP3'. Red coloured chemical anchor resin supplied in a pre-weighed dual cartridge. Apply as per manufacturer's instructions dated '12/11/2020'. Cure for 48 hours@7°C. For use with water up to 23°C. For use only as a resin anchor having been tested at a reduced surface area to volume ratio of 1,000mm² per 1 litre of water. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
‘STRONGHOLD SH-EP5’. Site applied, grey coloured chemical anchor resin which is supplied in a pre-mixed cartridge. Apply as per manufacturer’s instructions rev. 1 dated 03/02/2022. Cure for 4 days@7°C. For use with water up to 23°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'8EP2400 gaskets and 'O'-rings'. Black coloured, injection moulded 'O'-rings with a tested in-radius size of 0.9mm. Black coloured, extruded gaskets with a tested in-radius size of 0.5mm. Both gaskets and 'O'-rings have a shore hardness of 80 and are for use with water up to 85°C.
'H600042'. Black coloured, compression moulded EPDM material. Shore hardness 70. Tested in-radius size 1.3mm. For use with water up to 65°C.
'Hongli IRHD 70'. Black coloured, press moulded EPDM material. Shore hardness 70. Tested in-radius size 1.09mm. For use with water up to 23°C.
‘EWA 12150 (EW48) Rev.1. EWA 12155A (EP55) Rev.1. EWA 12160A (EW 60) Rev.1. EWA 12165 (EW65 2GS) Rev.1. EWA 12170 (WRC 70) Rev.1. EWA 12175 (WRC 75) Rev.1. EWA 12180 (EW80) Rev.1’. Black coloured, compression moulded, EPDM sheet materials. Shore hardness between 50 & 80. Tested in-radius size 1.2mm. For use with water up to 85°C.
‘SBPEP4555 (50), SBPEP55 (55), SBPEP60 (60), SBPEP65 (65), SBPEP70 (70), SBPEP75 (75) & SBPEP7085 (80)’. Black coloured, compression moulded EPDM rubber sheet materials with a shore hardness of between 50 & 80. Tested in-radius size of 1.0mm. For use with water up to 60°C.
'E6083AA'. Black coloured, compression moulded EPDM material. Shore hardness 60. Tested in-radius size 1.0mm. For use with water up to 85°C.
'EP601289C'. Black coloured, compression moulded EPDM material. Shore hardness 60. Tested in-radius size 1.0mm. For use with water up to 85°C.
'KRE70 (80-3)'. Black coloured, compression moulded EPDM material. Shore hardness 70. Tested in-radius size 1.0mm. For use with water up to 60°C.
'NB03973PWRC'. Black coloured, compression moulded NBR rubber. Shore hardness 71. Tested in-radius size 1.0mm. For use with water up to 23°C. From December 2023, the material is suitable for use with water up to 85°C.
‘TEC S27 R.-70 rosso washers & ‘O’ rings’. Red coloured, injection moulded VMQ washers & ‘O’ rings with a shore hardness of 70. The washers have an in-radius size of between 0.5mm & 2.6mm. The ‘O’ rings have an in-radius size of 0.5mm. From March 2024 the in-radius size range of the ‘O’ rings was extended to between 0.5mm & 2.6mm. For use with water up to 85°C.
'Tangit PVC-U Special Adhesive'. Straw coloured solvent cement. Apply as per manufacturer's instructions. Cure for 20 days@23°C. For use with water up to 23°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'STENFLEX® Butyl Rubber Expansion Joint'. Black coloured, compression moulded composite rubber expansion joint which consists of chlorobutyl/EPDM rubber & embedded polyamide fabric. Shore hardness 55. Tested in-radius size 2.0mm. For use with water up to 23°C.
Range of wall mounted electric showers with plastic bodies. Flow is controlled by a solenoid. The product is supplied with a shower hose and a shower handset (white or chrome plated - depending on model). Maximum working pressure 8.0 bar. Maximum operating temperature 55°C.
Range of electronically controlled taps (chromium plated brass). The assemblies incorporate a touch sensitive device and are supplied with a solenoid valve to control the flow. Spout outlet incorporates a plastic aerator and the product is supplied with stainless steel strainers. Maximum working pressure 8.0 bar. Maximum operating temperature 65°C.
Range of single hole, single outlet (fixed) electronically controlled tap assemblies (chrome plated brass finish). The flow is controlled by a solenoid valve activated via an infra-red sensor. The spout outlet incorporates a plastic aerator and a stainless-steel strainer on the inlet. Maximum working pressure 8.0 Bar Maximum operating temperature 70.0°C
Range of single hole, single outlet (fixed) electronically controlled combination tap assembles with brass bodies (various finishes). Flow is controlled via a solenoid valve activated via an infra -red sensor. The temperature is controlled via a ceramic cartridge and a single lever operating member. The spout outlet incorporates a pull-out spray with a plastic aerator. The trigger on the pull-out controls optional spray. The inlet adaptor incorporates a single check valve cartridge (verified by test, suitable for backflow protection against fluid category 2). The outlet incorporates a stainless-steel strainer and an aerator. Maximum working pressure 5.0 bar Maximum operating temperature 60°C.
Range of single hole, single outlet (swivel) combination tap assemblies (various finishes) with a pull-out spray mechanism. Flow is controlled via a ceramic cartridge headwork with a single lever operating member incorporating an infra-red sensor on the swivel arm which operates a solenoid valve. The spout outlet incorporates a plastic aerator and a hand spray mechanism, and the product is supplied with metal backnuts. Maximum working pressure 5.0 Bar. Maximum operating temperature 60°C.
Range of wall mounted, single hole, single outlet (fixed) electronically controlled combination tap assemblies (brushed stainless steel). The flow is controlled by a solenoid valve activated via an infra-red sensor. The inlet to the solenoid incorporates a stainless-steel strainer. The spout outlet incorporates a plastic aerator. The products are supplied with plastic backnuts and a stainless steel braided PEX lined flexible hose assembly for installation between the tap and the solenoid valve. The HK-Cha models added September are also supplied with a plastic flow regulator. Maximum working pressure 6.0 bar. Maximum operating temperature 60°C.
‘Type `AB` airgap (verified by test - suitable for backflow protection against fluid category 5) incorporating a float operated valve controlling the flow. The inlet hose incorporates an isolation valve. Maximum working pressure 10.0 bar. Cold water use only.
Spring loaded resilient trim in-line check valve cartridge with acetal body, incorporating a stainless steel spring and NBR or EPDM ‘O’-rings. To be housed in a specifically dimensioned body. Maximum working pressure 16.0 bar. Maximum operating temperature 65°C
Range of single check valve assemblies with DZR brass bodies. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Range of non-verifiable double check valve assemblies consisting of two spring loaded resilient trim in-line check valve cartridges housed in DZR brass bodies. Maximum working pressure 16.0 bar Maximum operating temperature 85°C
Single hole, single outlet (fixed, with swivel nozzle) bidet combination tap assembly (brass body in various finishes) incorporating ceramic cartridge headwork with single lever operating member. The spout outlet incorporates a plastic aerator and the product is supplied with a lever operated, pop-up waste. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.
Range of aerators with plastic bodies and filter screens. Maximum operating temperature 60°C
Rising spindle headwork with a brass body intended to be inserted into specifically dimensioned bodies. Maximum working pressure 10.0 bar. Maximum operating temperature 65°C.
Range of ceramic disc headworks with plastic bodies for insertion into specifically dimensioned bodies. Maximum working pressure 10.0 bar. Maximum operating temperature 85°C.
Range of thermostatic elements with copper bodies. Maximum operating temperature 90°C.
Range of single hole, single outlet (swivel) combination tap assemblies (chrome plated brass bodies), incorporating a ceramic cartridge headwork with a single lever operating member. The spout outlet are pull-out spray type, which incorporates aerators and approved single check valve cartridges, however the complete assemblies have not been tested to demonstrate backflow protection. Maximum working pressure 10.0 Bar Maximum operating temperature 65.°C
Single hole, single outlet (swivel) combination tap assembly stainless steel (various finishes), incorporating a ceramic cartridge headworks with single lever operating member and pullout spray handset. The spout outlet incorporates a plastic aerator and an approved single check valve cartridge, however, the complete product has not been fully tested to demonstrate it provides backflow protection. Maximum working pressure 5.0 bar. Maximum operating temperature 60°C
Single hole, single outlet (swivel) combination tap assemblies stainless steel (various finishes), incorporating a ceramic cartridge headworks with single lever operating member and pullout spray handset. The spout outlet incorporates a plastic aerator and an approved single check valve cartridge, however, the complete product has not been fully tested to demonstrate it provides backflow protection. Maximum working pressure 5.0 bar. Maximum operating temperature 60°C
Range of single hole, single outlet (fixed) combination tap assemblies, brass bodies (various finishes) incorporating a ceramic cartridge headwork with a single lever operating member. The spout outlet incorporates a plastic aerator. Products are supplied with approved pop-up waste. Maximum working pressure 5.0 bar. Maximum operating temperature 60°C
Range of single hole, single outlet (fixed) combination tap assemblies (chrome plated brass bodies) incorporating ceramic cartridge headworks with single lever operating members. The spout outlet incorporates a plastic aerator and the products are supplied with lever operated pop up wastes. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C
Page 94 of 222
We use cookies to give you the best possible experience with WRAS. Some are essential to provide website functions and ensure the website is secure. We also use cookies to help us understand how people use the site and to make improvements. Click "Accept All" to enable recommended settings or click "Manage cookies" to adjust your settings. For more details, see our Cookie Policy.
