Range of wall mounted, concealed thermostatic blending valves or exposed bar type thermostatic blending valves (chromium plated brass) incorporating a 2-way manual diverter valve controlling and diverting the flow between an overhead shower and a shower outlet with dome type operating members. The temperature is controlled independently via a thermostatic cartridge with a dome type operating member incorporating a manual override button incorporate. An approved check valve cartridge is also supplied, however, the complete product has not been fully tested to demonstrate it provides backflow protection. The products are supplied with a shower head, shower hose and handset. Maximum working pressure 10.0 bar. Maximum operating temperature 65°C (NU-019 & NU-022 models. All other models 60°C only).
Range of high pressure and low pressure thermostatic mixing valves. Flow is controlled by a solenoid valve and temperature is thermostatically controlled. Low pressure models incorporate a pump. The inlets of the valves incorporate an isolation valve, stainless steel strainer and a single check valve cartridge however, the complete assembly has not been tested to demonstrate it provides adequate backflow protection. The valves can be supplied with a shower rail, hose, handshower and/or ceiling mounted shower outlet. Valves with ‘HP’ in model have a maximum working pressure of 5.0 bar. All other valves marked with ‘LP’ have a maximum working pressure of 1.0 bar.
Non-metallic materials and components comply with BS6920 at 45°C
Range of concealed, wall mounted, thermostatic blending valves, (brass bodies, chrome trim sets). The products can consist of quarter turn ceramic disc or detent headworks, two-way diverter cartridges and a thermostatic cartridges (see models). All models incorporate approved check valve cartridges, however, the complete product has not been fully tested to demonstrate it provides backflow protection. Maximum working pressure 10 bar.
Non-metallic materials and components comply with BS6920 at 65°C
Range of T-type thermostatic mixing valves (chrome plated DZR brass). The 521928 model incorporates stainless steel strainers in the inlets and approved check valve cartridges, verified by test (suitable for backflow protection against Fluid Category 2). Maximum working pressure: 10.0 Bar. Temperature: 90°C
Range of wafer or lug type butterfly valves with blue epoxy coated cast or ductile iron bodies, blue epoxy coated ductile iron or stainless-steel discs and EPDM seats. Leaver or hand wheel operated. Maximum working pressure 16.0 bar.
Non-metallic materials and components comply with BS6920 at 85°C
Range of concealed two way & three way ceramic disc diverters, (brass bodies – various trim sets and operating members). Maximum working pressure: 10.0 Bar
Range of pre-set pressure relief valves (set at 3.0 bar) with nylon bodies, EPDM diaphragms and ‘O’-rings.
Non-metallic materials and components comply with BS6920 at 85°C
Range of lever operated spherical valves with stainless steel bodies and ball with PTFE seats. Maximum operating pressure 16.0 bar (2019S) or 63.0 bar (2013ND & 2006SC-FW).
Non-metallic materials and components comply with BS6920 at 85°C
Range of quarter turn, lever handle or butterfly operated spherical valves with nickel plated brass bodies, chrome plated brass balls and PTFE seals. For use with copper pipe BS EN 1057. Maximum working pressure 25.0 bar. Maximum operating temperature 85°C.
Range of inline spherical valves, (nickel plated brass bodies), chrome plated brass balls, PTFE seats and washers with lock-shield, single lever or T-type operating members. Maximum working pressure: ¼” to 1” = 40.0 bar, 1¼” to 2” = 32.0 bar, 2½” to 3” = 25.0 bar, 4” = 20.0 bar.
Non-metallic materials and components comply with BS6920 at 85°C
Range of lever operated, full bore spherical valves with brass bodies (brushed chrome) and chrome plated brass balls and a range of different operating members. Sizes ¼” to ½” have a maximum working pressure of 64.0 bar. Sizes ¾” to 2½” have a maximum working pressure of 40.0 bar. Cold water use only.
Range of gate valves with a non-rising spindle with a handwheel operating member or lockshield connection. All models have brass body and brass wedge. For use with copper pipe (manufactured to EN1057). Maximum working pressure 16.0 bar.
Non-metallic materials and components comply with BS6920 at 85°C
Range of gate valves with a non-rising spindle with a handwheel operating member. All models have brass body and brass wedge. For use with copper pipe (manufactured to EN1057). Maximum working pressure 16.0 bar.
Non-metallic materials and components comply with BS6920 at 85°C
Range of screw down valves with brass or DZR brass bodies, brass or DZR brass bonnets, EPDM washers and PTFE seats. Compression connection to be used with copper pipe manufactured to EN1057. Maximum working pressure 16 bar. Maximum operating temperature 85°C.
‘Promag’. Factory applied, black coloured PUR coating system comprising of a primer and topcoat. ‘Promag Primer’ is a two-part primer to be mixed in a 1:2 mass ratio before applying as per manufacturer’s core instructions ‘TLB: 10000043811’, ‘Version: M’. Cure/dry for 2 hours@23°C. ‘Promag Topcoat’ is a three-part topcoat to be mixed in a 92.59:5.19:2.22 mass ratio before applying as per manufacturer’s core instructions ‘TLB: 10000043811’, ‘Version: M’. Cure/dry for 20 seconds@20-26°C. For use with water up to 23°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'VPC5009 Potable FBE'. Factory applied, blue coloured epoxy powder coating. Pre-heat substrate at 200°C and then apply by dipping in a fluidised bed as per manufacturer's instructions dated 10th January 2019. Cure for 15 minutes@200°C. For use with water up to 23°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'571983 & 571984'. White coloured (semi-translucent), extruded PTFE tape. For use with water up to 85°C.
'ESTANE® 58197 Nat 022'. In August 2023 'ESTANE® 58197 NAT 01' was added to the approval. Natural (transparent, colourless), injection moulded thermoplastic polyurethane materials. For use with water up to 85°C.
'Titan A202'. Site applied, pale yellow coloured hydrophilic polyurethane foam. Apply as per manufacturer's Tech Sheet '03', dated '10.01.2023' and spray treated surface with water. Cure for 6 hours at an ambient temperature (19-21°C). For use with water up to 23°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Sunaflex T 8193'. Black coloured, compression moulded EPDM rubber material. Shore hardness 80. Tested in-radius size 1.0mm. For use with water up to 23°C.
'FKM 90 Black 6019020105-CMP00700'. Black coloured, compression moulded FKM material. Shore hardness 90. Tested in-radius size 1.1mm. For use with water up to 85°C.
‘N70 60 003 197’. Black coloured, injection moulded NBR material. Shore hardness 70. Tested in-radius size 1.0mm. For use with water up to 85°C.
'Supercast PVC Waterstop Hydrofoil'. Blue coloured, extruded PVC waterstop. For use with water up to 23°C. These materials are for use in concrete reservoirs and similar structures, constructed in accordance with the design criteria of BS EN 1992 with respect to normal frequency of joints. The materials have been tested at a reduced surface area to volume ratio of 1000mm² per litre as specified in BS 6920: Part 1
'TamAcryl 2000 Orange or Blue with corrosion inhibitor', orange coloured or blue coloured (once mixed), site applied acrylic grouts. Mix Part A (orange or blue) with 2% accelerator and then mix with Part B (colourless) in a 1:1 volume ratio. Apply as per manufacturer’s TDS 'V1UK20 – 2020.10.22'. Cure for 12 hours at 16°C. For use with water up to 23°C. This material is only approved for the mixing & curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval. These materials are for use in concrete reservoirs and similar structures, constructed in accordance with the design criteria of BS EN 1992-3:2006 (Design of concrete structures – Liquid retraining and containing structures) with respect to normal frequency of joints. The material has been tested at a reduced surface area to volume ratio of 1000mm² per litre.
'TamPur 150'. Site applied, Hydrophilic polyurethane foam which is an amber coloured liquid when unreacted and a pale yellow coloured, flexible foam material when cured. Mix TamPur 150 with water in a volumetric ratio of 1:1 and apply as per manufacturer’s TDS 'V1UK19 – 2019.4.25'. Cure for 24 hours at 7°C. For use with water up to 23°C. This material is only approved for the mixing & curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval. These materials are for use in concrete reservoirs and similar structures, constructed in accordance with the design criteria of BS EN 1992-3:2006 (Design of concrete structures – Liquid retraining and containing structures) with respect to normal frequency of joints. The material has been tested at a reduced surface area to volume ratio of 1000mm² per litre.
'Akfix PS253 Pipe Sealant Medium Strength'. Blue coloured pipe sealant. Apply as per manufacturer's TDS 'Rev.01', issue date '23/10/2019'. Cure for 24 hours@23°C. For use with water up to 85°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
Range of single hole, single outlet, electronically controlled tap assemblies (brass body – various finishes). The flow is controlled via a solenoid valve and activated by an infra-red sensor on the front of the spout. The spout outlet incorporates a plastic aerator. Models xxx.yyy.170E/W are supplied with a click clack waste. Maximum working pressure 5.0 bar.
Non-metallic materials and components comply with BS6920 at 60°C
Range of wall mounted, single-hole, single outlet (fixed) electronically controlled combination tap assemblies (chrome plated brass bodies). Flow is controlled via a solenoid, activated via an infra-red sensor. The outlets incorporate plastic aerators. Maximum working pressure 8.0 bar Maximum operating temperature 70°C
Non-metallic materials and components comply with BS6920 at 70°C
Range of wall mounted, electronically operated, combination tap assemblies (stainless steel body, various finishes - see model), comprising of a Premix control unit and a spout. The flow is controlled by a solenoid valve, (Premix control unit), which is actuated via an infrared sensor. The central section of the valve incorporates a plastic strainer. Both inlets of the Premix control unit incorporate an approved single check valve cartridge, however the complete assembly has not been tested for backflow protection. The spout outlet incorporates a plastic aerator. Maximum working pressure 8.0 bar. Maximum operating temperature 60°C.
Non-metallic materials and components comply with BS6920 at 60°C
Range of single hole, single outlet, electronic touch free, deck mounted taps (chromium plated brass) for cold or premixed water. Flow is controlled via solenoid valves, actuated by infra-red sensors. Power is supplied by externally mounted 9V battery pack or 9V transformer. The inlet hoses have a stainless-steel strainer and the spout outlets incorporate plastic aerators. Maximum working pressure 8.0 bar.
Non-metallic materials and components comply with BS6920 at 65°C
Range of wall mounted, single-hole, single outlet (fixed) electronically controlled combination tap assemblies (chrome plated brass or stainless-steel bodies) which are supplied with pre-mixed water. Flow is controlled via an infra-red activated solenoid valve and the spout outlets incorporate plastic aerators. Maximum working pressure 8.0 bar
Non-metallic materials and components comply with BS6920 at 65°C
Range of single hole, single outlet, fixed, electronically controlled tap assemblies (chrome plated brass bodies). Flow is controlled via an infra-red activated solenoid valve and the spout outlets incorporate plastic aerators. The inlets incorporate a stainless-steel filter washer. Maximum working pressure 8.0 bar
Non-metallic materials and components comply with BS6920 at 65°C
Range of single-hole, single outlet, (fixed), electronically controlled tap assemblies (chrome plated brass or stainless steel bodies). Flow is controlled via solenoid valve activated via an infra-red sensor. The spout outlets incorporate plastic aerators. Maximum working pressure 8.0 Bar.
Non-metallic materials and components comply with BS6920 at 65°C
Range of wall mounted, electronically controlled combination tap assemblies, (chrome plated brass or stainless steel bodies). The flow is controlled by a solenoid valve that is activated via an infra-red sensor The spout outlet incorporates a plastic aerator. The product incorporates a stainless steel braided PEX lined flexible connection hose assembly, connecting the spout to the solenoid valve. Maximum working pressure 8.0 Bar
Non-metallic materials and components comply with BS6920 at 65°C
Range of electronically operated combination tap assemblies, (chrome plated brass bodies). The flow is controlled by a solenoid valve which is actuated via an infrared sensor. The spout outlet incorporates a plastic aerator. The product incorporates a stainless steel braided PEX lined flexible connection hose, connecting the tap to the solenoid valve. Maximum working pressure 8.0 Bar
Non-metallic materials and components comply with BS6920 at 65°C
Range of wall mounted, single-hole, single outlet, electronically controlled combination tap assemblies, (chrome plated brass or stainless steel bodies). The flow is controlled by a solenoid valve activated via an infra-red sensor. The spout outlet incorporates a plastic aerator. The products incorporate a stainless steel braided PEX lined flexible hose assembly, connecting the spout to the solenoid valve. Maximum working pressure 8.0 Bar.
Non-metallic materials and components comply with BS6920 at 65°C
Range of bottom entry BS1212-4 telescopic fill valves with plastic bodies. Maximum working pressure 10.0 bar. Cold water use only.
Range of concealed WC dual flushing cisterns with a vertical BS 1212-4(2016) float operated inlet valve providing a Type AG air gap arrangement and a dual flush outlet valve. The flush volume is operated by a two-push button assembly. The product also incorporates a servicing valve and flexible hose on the inlet supply. Maximum working pressure 10 Bar, cold water use only.
Range of tundishes incorporating a plastic or coated, mild steel body. Maximum operating temperature 85°C.
Range of single hole, single outlet over the rim (swivel nozzle) bidet combination tap assemblies with brass bodies (various finishes – see models), incorporating quarter (L & F models) or half turn (H models) ceramic disc headworks with a cross top or lever operating members. The spout outlets incorporate plastic aerators. Maximum working pressure 5.0 Bar. Maximum operating temperature 60.0°C.
Range of ceramic cartridge headworks with plastic bodies & silicone rubber seals. For insertion into specifically dimensioned bores. Maximum working pressure 10.0 bar. Maximum operating temperature 85°C
Range of wall mounted, single hole, single outlet (fixed) combination tap assemblies (brass bodies - various finishes), incorporating ceramic cartridge headworks with single lever operating members. The spout outlets incorporate plastic aerators. Maximum working pressure 10 bar. Maximum operating temperature 65°C
Range of single hole, single outlet (fixed) combination tap assemblies (brass bodies, various finishes - see model), incorporating a ceramic cartridge headwork with a single lever operating member. The spout outlet incorporates a plastic aerator. The product is supplied with or without a pop-up waste (see model), Maximum working pressure 10.0 Bar. Maximum operating temperature 60°C.
Non-metallic materials and components comply with BS6920 at 60°C
Range of single hole, single outlet (fixed) combination tap assemblies (brass bodies – various finishes) incorporating ceramic cartridge headworks with a single lever type operating member. The spout outlets incorporate a plastic aerator. Maximum working pressure 10.0 Bar.Maximum operating temperature 60°C
Range of single-hole, single outlet, (swivel) combination tap assemblies, (brass bodies – various finishes), incorporating ceramic cartridge headworks with single lever operating members. The spout outlets incorporate plastic aerators. The inlets incorporate stainless steel strainer washers. Maximum working pressure 10.0 Bar
Non-metallic materials and components comply with BS6920 at 70°C
Range of single hole, single outlet (swivel) combination tap assemblies (brass bodies - various finishes). Models (F1021 & F7132B) incorporate quarter turn ceramic disc headworks with either single lever or cross-top type operating members. Models (F1025X, F1026 & F7149) incorporate ceramic cartridge headworks with single lever operating members. All spout outlets incorporate plastic aerators. Maximum working pressure 10.0 bar. Maximum operating temperature 65°C.
Range of wall mounted two-hole, single outlet (fixed) comination tap assemblies with brass bodies (chromium plated), ceramic cartridge headworks and single lever operating members. Spout outlets incorporate plastic aerators. Maximum operating pressure 10 bar. Maximum operating temperature 60°C
Range of wall mounted, three-hole, single outlet (fixed) combination tap assemblies incorporating quarter turn ceramic disc headwork with cross top or single lever operating members (See models). The spout outlets incorporate a plastic aerator. Maximum working pressure 10.0 Bar.
Non-metallic materials and components comply with BS6920 at 60°C
Range of three-hole, single outlet (swivel) combination tap assemblies, incorporating quarter turn ceramic disc headworks with single lever or cross top type operating members (see models). The spout outlets incorporate plastic aerators. The products are supplied with stainless steel braided PEX lined flexible hose assemblies for installation between the side valves and the spouts, as well as click type pop-up wastes (verified by test) and metal backnuts. Maximum working pressure 10.0 bar.
Non-metallic materials and components comply with BS6920 at 60°C
Range of four hole, single outlet (fixed) combination tap assemblies (brass, in various finishes), incorporating a ceramic cartridge headwork with single lever operating members and a self-cancelling diverter to shower outlet, with stainless steel braided silicone lined flexible interconnecting hoses. The connection to shower outlet incorporates a single check valve, verified by test (suitable for backflow prevention against Fluid Category 2). The spout outlet incorporates a plastic aerator. The product is also supplied with a shower hose and handset. Supplied with metal backnuts. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.
Page 10 of 18
We use cookies to give you the best possible experience with WRAS. Some are essential to provide website functions and ensure the website is secure. We also use cookies to help us understand how people use the site and to make improvements. Click "Accept All" to enable recommended settings or click "Manage cookies" to adjust your settings. For more details, see our Cookie Policy.
