Range of high pressure and low pressure thermostatic mixing valves. Flow is controlled by a solenoid valve and temperature is thermostatically controlled. Low pressure models incorporate a pump. The inlets of the valves incorporate an isolation valve, stainless steel strainer and a single check valve cartridge however, the complete assembly has not been tested to demonstrate it provides adequate backflow protection. The valves can be supplied with a shower rail, hose, handshower and/or ceiling mounted shower outlet. Valves with ‘HP’ in model have a maximum working pressure of 5.0 bar. All other valves marked with ‘LP’ have a maximum working pressure of 1.0 bar.
Non-metallic materials and components comply with BS6920 at 45°C
“Heatguard Dual Thermostatic Mixing Valves”, range of T type thermostatic mixing valves with brushed chrome plated brass bodies. The inlets incorporate check valve cartridges (all models) and isolation valves (models HEAT110616 & HEAT110625 only). Check valve cartridges are verified by test (suitable for backflow protection against Fluid Category 2). Products also include stainless-steel strainers. Maximum working pressure 6 Bar.
Non-metallic materials and components comply with BS6920 at 85°C
Range of concealed thermostatic shower mixing valves with (brass bodies - various finishes), incorporating a ceramic disc diverter valve controlling the flow between two outlets. The temperature is controlled independently via a thermostatic cartridge with a manual override button. The products are supplied with trim sets and operating members in a various finishes. The 15 708 xxx model has cube type operating members, and all other models have single lever operating members. Both inlets incorporate an approved check valve cartridge (however, the complete product has not been fully tested to demonstrate it provides backflow protection) Maximum working pressure 10.0 Bar.
Non-metallic materials and components comply with BS6920 at 60°C
Range of concealed thermostatic shower mixing valves with (brass bodies - various finishes), incorporating a quarter turn ceramic disc headwork controlling the flow. The temperature is controlled independently via a thermostatic cartridge with manual override button. The products are supplied with trim sets and operating members in a various finishes. The 15 707 xxx models have cube type operating members, the 15 714 xxx & 15 758 xxx models have single lever operating members. Both inlets incorporate an approved check valve cartridge, however, the complete product has not been fully tested to demonstrate it provides backflow protection. Maximum working pressure 10.0 Bar.
Non-metallic materials and components comply with BS6920 at 60°C
Range of butterfly valves incorporating blue epoxy coated ductile iron bodies and discs. Maximum working pressure 16.0 bar.
Non-metallic materials and components comply with BS6920 at 65°C
Range of wafer or lugged butterfly valves with blue epoxy coated ductile iron bodies, stainless steel discs and EPDM seats. The valves can either be lever or gear oprated via a hndwheel. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Range of wafer or lugged butterfly valves with blue epoxy coated ductile iron bodies, stainless steel discs and EPDM seats. The valves can either be lever or gear operated via a handwheel. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Range of float operated valves with brass bodies. DN15-DN80 maximum working pressure 16 bar. DN100 maximum working pressure 14 bar. Maximum operating temperature for cold water use only.
Range of normally closed solenoid valves with brass bodies and EPDM diaphragms. Maximum working pressure 10.0 bar.
Non-metallic materials and components comply with BS6920 at 85°C
Range of normally closed, normally open or latching inline solenoid valves with brass bodies and EPDM ‘O’-rings and diaphragms. Maximum working pressure: PU225DN-03, PU225DN-04, PU225DN-08, PU225DN-12, PU225DN-14, LPU225D-03, LPU225D-04, LPU225D-08, LPU225D-12 & LPU225D-14 models - 7.0 bar. All other models - 10.0 bar. Cold water use only.
Range of normally open solenoid valves with brass bodies, EPDM ‘O’-rings and diaphragm. The inlet incorporates a stainless-steel strainer. Maximum working pressure 10.0 bar. Maximum operating temperature, EV220BW 50BE G2E NO000 model: Cold water use only, all other models: 85°C. From November 2023 onwards all models: 85°C.
Range of normally open solenoid valves with brass bodies, EPDM diaphragms and ‘O’-rings. Maximum working pressure 10.0 bar.
Non-metallic materials and components comply with BS6920 at 60°C
Range of in-line spherical valves with brass bodies, chromium plated brass ball, NBR rubber ‘O’-rings and single lever operating members. Maximum working pressure 16.0 bar.
Non-metallic materials and components comply with BS6920 at 85°C
Range of spherical valves with a single lever or ‘T’ handle operating member. The products have a DZR brass body and a chrome plated DZR brass ball, except for the models with the ‘-OT’ suffix, models have (nickel-plated brass bodies) and chrome plated brass ball. The products are supplied with various end connections (see model). Maximum working pressures: 15mm to 28mm = 40 Bar 35mm = 25 bar 42mm to 54mm = 16 bar (All models). 42 to 54mm = 10 Bar (4E05, 4E05-OT, 4E06 and 4E06-OT models) Maximum operating temperature 40.0°C
Range of lever operated spherical valves with nickel plated brass bodies incorporating chromium plated brass balls. For use with copper pipe. Maximum working pressure 25.0 bar. Maximum operating temperature 100°C.
Range of spherical valves with brass bodies (nickel plated) and brass (chromium plated) balls, PTFE seats and NBR o-rings. Maximum working pressure: ½” to 1” = 40.0 bar, 1¼” to 2” = 25.0 bar. Cold water use only.
Range of resilient seated gate valves with cast iron bodies (blue epoxy coated), EPDM coated cast iron wedges and a handwheel operating member. Maximum working pressure 16.0 bar.
Non-metallic materials and components comply with BS6920 at 85°C
Range of stop valves with either DZR brass, brass, bronze or chrome plated bodies with T-type or lockshield (LS) operating members. Compression models are for use with copper pipe manufactured to BS EN 1057. Maximum working pressure 16.0 bar.
Non-metallic materials and components comply with BS6920 at 85°C
Range of brass and DZR brass stopcock incorporating EPDM and PTFE washers. Compression connections, to be used with copper pipe EN1057 only. Maximum working pressure 16.0 bar.
Non-metallic materials and components comply with BS6920 at 85°C
Range of stop valves with brass bodies, EPDM gaskets and PTFE wear rings and packings. Compression connection to be used with copper pipe EN1057. Maximum working pressure 16.0 bar. Maximum operating pressure 85°C
Range of brass stopcock incorporating EPDM and PTFE washers. Compression connections, to be used with copper pipe EN1057 only. Maximum working pressure 16.0 bar.
Non-metallic materials and components comply with BS6920 at 85°C
Range of screw down valves with brass or DZR brass bodies, brass or DZR brass bonnets, EPDM washers and PTFE seats. Compression connection to be used with copper pipe manufactured to EN1057. Maximum working pressure 16 bar. Maximum operating temperature 85°C.
Range of stop valves withbreonze, brass or chrome plated brass bodies, EPDM and PTFE washers incorporating a T type or lockshield operating members. To be used with copper pipe EN1057. Maximum working pressure 16.0 bar. Maximum operating pressure 85°C
Range of front loading commercial washing machines with flow controlled by solenoid valves and discharged via a type `AD` airgap (verified by test - suitable for backflow protection against fluid category 5). The products are supplied with a dual layer composite supply hose (blue outer/black inner). Maximum working pressure 5.0 bar. Cold water use only
Activflo range of water conditioners with stainless steel bodies. Models with compression connections are for use with copper pipe (manufactured to BS EN 10 57), stainless steel pipe (BS EN 10312:2002), polybutylene (BS 7291-2) or PE-X pipe (BS7291-3). Maximum working pressure 16 bar. Maximum operating temperature 99°C
Electrolytic and magnetic scale inhibitors incorporating copper or nickel coated copper bodies. Compression models are to be used with copper pipe manufactured to BS EN1057. Maximum working pressure 10.0 bar. Cold water use only.
Range of electronically controlled ion exchange water softeners (salt regenerated) for commercial and domestic use. Maximum working pressure 5.0 bar. Cold water use
‘ET Sulphate Resisting Cement’. Factory applied, grey coloured cement. Mix and apply as per manufacturer’s ‘Standard Operating Procedure 'ET-SAM/DIP-PP/SOP/014', 'Rev. No 01', dated '15.12.2019'. Cure for 40 days@26°C. For use with water up to 65°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'RMD 7080/xx, RUD 2230/xx, RMD 7100/xx, RUD 2247/xx, RUD 2273/xx, RMD 7061/xx'. 'xx' denotes the customer and can be replaced with numbers between 01 & 99. Factory applied, blue coloured enamel coating. Apply as per manufacturer's instructions '0703231010' dated 14.03.23. Cure for 10 minutes@860°C. For use with water up to 85°C. These materials are only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the materials are not covered by the scope of the approval.
ML-9005WGL414 (black coloured - RAL 9005), ML-6018WGL424 (green coloured - RAL 6018), ML-9A10WGL444 (white coloured - RAL 9010), ML-5007WGL424 (blue coloured - RAL 5007) & ML-6621WGL424 (green coloured - Pantone 334 C). Factory applied, electro-statically sprayed epoxy powder coatings. Apply as per manufacturer’s Product Data Sheet ‘Pdb_ML-WGL414-EN (03-2023)’, dated ’23.03.2023’. Stove (cure) for 8 minutes at 180°C. For use with water up to 65°C. These materials are only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'KUBOTAPOWDER TK1413F M'. Factory applied, grey coloured epoxy resin powder coating. Apply as per manufacturer's Technical Information 'No. SG23180' dated '11 June 2021'. Cure for 10 minutes@200°C. For use with water up to 60°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
‘KUBOTA SEAL AC’. Factory applied, colourless acrylic resin coating. Apply as per manufacturer’s instructions ‘ref. no. 65700H-2.3’ dated 'Mar. 14.2017'. Cure for 7 days@27°C. For use with water up to 60°C. This material is only approved for the curing conditions that appear on the approval. If the curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Titanseal 989'. Site applied, two-component, grey coloured (once mixed) polyurethane coating. Mix the grey coloured (opaque) base coating with the amber coloured hardener in a 3:1 volume ratio and apply Coat 1 as per manufacturer's application instructions dated '09.03.2018'. Cure for 4 hours@7°C. Mix and apply Coat 2 using the same mix ratio and application instructions and then cure for 14 days@7°C. For use with water up to 23°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the materials are not covered by the scope of the approval.
'Electrocoat EP812 Blue'. Factory applied, blue coloured, two-part epoxy coating consisting of a base and hardener. Mix base and hardener in a volume ratio of 3:1 and apply as per manufacturer's data sheet 'ECL / TDS / EP 812 - BLUE, RAL 5017', issue date '12-Jan-13', version '03', revision date '25-Sept-14'. Cure for 1 hour@60°C followed by 7 days@28°C. For use with water up to 23°C. From March 2024 the material is for use with water up to 60°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Maxline 100 Potable Water Coating Blue & Grey'. Site applied, two-component polyurethane coatings which are available in blue or grey colours (once mixed). Mix Part A (blue or grey opaque liquid) with Part B (amber, translucent liquid) in a 100:30.5 weight ratio and apply as per manufacturer's technical data sheet 'TDSMLI100.rv5.04042023'. Cure for 14 days@7°C. For use with water up to 23°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the materials are not covered by the scope of the approval.
'Weberdry epo PW'. Site applied, light grey coloured (once mixed), two-component epoxy coating. Mix Part A (light grey coloured) with Part B (translucent, yellow coloured) in a weight ratio of 100:20. Apply as per manufacturer's TDS 'Edition: 04.23-A'. Cure for 24 hours@25°C. Mix and apply a second coat in the same way and then cure for 14 days@25°C. For use with water up to 23°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
`EcoZmart Waterproofing`. Site applied, grey coloured tanking slurry. Mix tanking slurry with water in a 3:1 volume ratio and apply coat 1 as per manufacturer's IFU 'TCOWP001', dated '26/05/2023'. Cure for 24 hours@7°C. Mix tanking slurry with water in a 3:1 volume ratio and apply coat 2, 24 hours after the first coat, as per manufacturer's IFU IFU 'TCOWP001', dated '26/05/2023'. Cure for 14 days@7°C. For use with water up to 23°C. This material is only approved for the mixing & curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Vinoleo 77/14'. Amber coloured, soap based lubricant. Apply as per manufacturer's instructions. For use with water up to 23°C.
'PPELXS314G20NA'. Beige coloured, injection moulded PPE material. For use with water up to 85°C.
'DIC.PPS FZ-2140-F3 BLACK'. 'DIC.PPS FZ-2140-F3 BLACK-U' was added to the approval in September 2023. Black coloured, injection moulded PPS materials manufactured in Vienna, Austria. For use with water up to 85°C.
'UW61424 & UW61427 – Instinct'. White coloured, extruded PTFE tapes. For use with water up to 85°C.
'7EP2114 'O'-rings'. Black coloured, injection moulded EPDM 'O'-rings. Shore hardness 70. Tested in-radius size 0.9mm. For use with water up to 85°C.
'E7014F'. Black coloured, compression moulded EPDM material. Shore hardness 70. Tested in-radius size 1.0mm. For use with water up to 23°C. From April 2023, the material is for use with water up to 85°C.
'Loctite SI 5331 (known as 'Loctite 5331')'. White coloured silicone thread sealant. Apply as per manufacturers technical data sheet ‘reference 1.7’ dated May 2014. Cure for 96 hours@23°C. For use with water up to 85°C. This material is only approved for the curing conditions that appear on the approval. If the curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
Range of single hole, single outlet (fixed) combination tap assemblies (chrome plated – brass bodies). Flow is controlled via a solenoid which is actuated via an infrared sensor and the temperature is controlled by a manual lever. The spout outlets incorporate plastic aerators. The inlet hoses incorporate stainless steel strainers and an approved check valve cartridge; however, the complete product has not been fully tested to demonstrate it provides backflow protection. Maximum working pressure 8.0 Bar.
Non-metallic materials and components comply with BS6920 at 60°C
Range of check valve cartridges with plastic bodies to be inserted into specifically dimensioned bodies. Maximum working pressure 8.6 bar. Maximum operating temperature 60°C
Non-metallic materials and components comply with BS6920 at 60°C
Range of flow restrictors with natural/unpigmented plastic bodies and inserts (where applicable), and EPDM ‘O’-rings. The LFB-FDN15, BFDN15SH & LFB-FDN15SH models also incorporate a stainless-steel filter.
Non-metallic materials and components comply with BS6920 at 85°C
Range of plastic aerators. Aerators which include ‘gpm max’ in the model name, incorporate a plastic flow regulator. Maximum operating temperature 60°C
Range of aerator kits incorporating plastic flow regulators (1.9l/min, 3.5l/min & 5.0l/min) with plastic bodies and EPDM ‘O’ rings. Plastic adaptors, NBR washers and chromium plated brass housings may also be supplied as part of the kit. Maximum operating temperature 65°C.
Range of quarter turn ceramic disc headworks with brass bodies and NBR ‘O’ rings, for insertion into specifically dimensioned bores. Maximum working pressure 10.0 Bar Maximum operating temperature 85.0°C
Non-metallic materials and components comply with BS6920 at 85°C
Page 10 of 27
We use cookies to give you the best possible experience with WRAS. Some are essential to provide website functions and ensure the website is secure. We also use cookies to help us understand how people use the site and to make improvements. Click "Accept All" to enable recommended settings or click "Manage cookies" to adjust your settings. For more details, see our Cookie Policy.
