Concealed WC flushing cisterns incorporating a BS 1212-4 side entry compact type float operated inlet valve providing a Type AG air gap with a dual flush drop valve for full flush volumes of up to 6 litres and a reduced flush of up to 3 litres. The cistern is operated by a manual push button and incorporates a angle valve and flexible hose on the inlet supply. Maximum working pressure 10.0 bar. Cold water use only.
Range of high and low level BS EN 14055 (2018) WC cisterns incorporating a side or bottom entry float operated inlet valve discharging via a Type AG air gap and a dual flush or mono flush syphon for full flush volumes of up to 6 litres and a reduced flush of up to 4 litres.. Maximum working pressure 10.0 bar. Cold water use only.
Range of floor mounted, single hole, single outlet (fixed), combination tap assemblies (chromium plated brass), incorporating a ceramic cartridge headwork with a single lever operating member and a manual diverter to shower outlet. The spout has a waterfall outlet. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.
Range of flushing valves (gunmetal body) which incorporate a screw down stop valve, spherical valve and air gap to drain. Maximum working pressure 10.0 bar. Cold water use only.
Range of one piece water storage cisterns with a screened breather and over flow. Model 46714 iBoost+200 has a rectangular weir overflow Model 46712 iBoost+200 has a circular overflow Cold water only.
Range of self-closing headworks with stainless steel bodies to be housed in specifically dimensioned bodies. Maximum working pressure 8.8 bar.
Non-metallic materials and components comply with BS6920 at 85°C
Range of quarter turn ceramic disc headworks with brass bodies and NBR ‘O’ rings for insertion into specifically dimensioned bores. Maximum working pressure 5.0 Bar.
Non-metallic materials and components comply with BS6920 at 60°C
Range of thermostatic cartridges with plastic or brass bodies and stainless-steel filters. For insertion into specifically dimensioned bores.
Non-metallic materials and components comply with BS6920 at 65°C
Range of single hole, single outlet pull out spray, combination tap assemblies (brass bodies, various finishes – see models) incorporating ceramic cartridge headworks with single lever operating members controlling the hot and cold and a quarter turn ceramic disk headwork with a dome type operating member controlling chilled water supply. The spout outlet incorporates a plastic aerator. The inlet from the tap to the pull-out spray hose incorporates an approved check valve cartridge, however, the complete product has not been fully tested to demonstrate it provides backflow protection. Maximum working pressure 10.0 Bar.
Non-metallic materials and components comply with BS6920 at 60°C
Single hole, single outlet (fixed) combination tap assemblies (chrome plated brass bodies), incorporating a ceramic cartridge headwork with single lever operating member. The spout outlets incorporate plastic flow straighteners or aerators. The products are supplied with approved click type wastes, verified by test. . Maximum working pressure - 5.0 Bar Maximum operating temperature 65.0°C
Range of single hole, single outlet (fixed) combination tap assemblies (chrome plated brass), T-638-series incorporates quarter turn ceramic disc headworks with single lever operating members T-638M series incorporates, non-rising spindle headworks with dome or cross-top operating members. The spout outlets incorporate a plastic flow straightener. The products are supplied with a lever operated pop-up waste. Maximum working pressure 10.0 bar. Max operating temperature 85°C.
Range of single hole, single outlet (fixed) combination tap assemblies (chromium plated brass), incorporating a ceramic cartridge headwork with a single lever operating member. The spout outlet incorporates a plastic flow straightener (TR1025 and TR1026 models) or a plastic aerator (all other models). The products are supplied with or without a click type pop-up waste (see model). Maximum operating pressure: MINI models 10.0 bar, all other models 5.0 bar. Maximum operating temperature 65°C.
Range of single hole, single outlet fixed combination tap assemblies (brass body with various finishes), incorporating a ceramic cartridge headwork with either a single lever or cross top operating member. The spout outlets incorporate a plastic aerator. Products are supplied with PEX inner-lined grey plastic braided inlet hoses. Maximum working pressure 10 bar.
Non-metallic materials and components comply with BS6920 at 60°C
Range of single hole, single outlet fixed combination tap assemblies (brass bodies, various finishes – see models). TSA models incorporate quarter turn ceramic disc headworks with cross-top operating members. TDA models incorporate a ceramic cartridge headworks with a single lever operating member. The spout outlets incorporate plastic aerators. Maximum operating pressure 10.0 bar.
Non-metallic materials and components comply with BS6920 at 65°C
Single hole, single outlet (fixed) combination tap assembly (chromium plated brass) incorporating a ceramic cartridge headwork with a single lever operating member. The spout outlet incorporates a plastic aerator. Supplied with click type pop-up waste. Maximum working pressure 10 Bar
Non-metallic materials and components comply with BS6920 at 60°C
Range of single hole, single outlet (fixed) combination tap assemblies (chrome plated brass), incorporating ceramic cartridge headworks or ceramic disk headworks (model 152108) with single lever operating members. The spout outlet incorporates either a plastic aerator or flow straightener, (Model 152308 is only supplied with an aerator) . The products are supplied with a click type pop-up waste. 152108 and 179428 maximum working pressure 10.0 bar. 152038, 143338 and 179438 maximum working pressure 5.0 bar.
Non-metallic materials and components comply with BS6920 at 65°C
Range of floor mounted, single hole, single outlet fixed combination tap assembly (various finishes), incorporating a ceramic cartridge headwork with a single lever operating member and a self- cancelling diverter to shower outlet. The product is supplied with a shower hose and handset. Maximum working pressure 10.0 bar.
Non-metallic materials and components comply with BS6920 at 65°C
Range of single hole, single outlet (swivel) combination tap assemblies (chromium plated brass) incorporating ceramic cartridge headwork and single lever operating member. The spout outlets incorporate a plastic aerator. A pop-up waste is also supplied. Maximum working pressure 10.0 Bar.
Non-metallic materials and components comply with BS6920 at 60°C
Range of single hole, single outlet (swivel) combination tap assemblies with brass bodies (chrome plated), incorporating a ceramic cartridge headwork with single lever operating members. The spout outlet incorporates a plastic aerator. Maximum working pressure 10.0 bar.
Non-metallic materials and components comply with BS6920 at 60°C
Range of single hole, single outlet (swivel), combination tap assemblies (brass bodies with various finishes), incorporating ceramic cartridge or quarter turn ceramic disc headworks with single lever, cross-top or dome operating members. The spout outlets incorporate a plastic aerator. Maximum working pressure 5.0 or 10.0 bar.
Non-metallic materials and components comply with BS6920 at 60°C
Single hole, single outlet (swivel) combination tap assembly (chromium plated brass) incorporating a rising spindle headwork with a single lever operating member. The spout outlet incorporates a plastic flow straighter. Maximum working pressure 10.0 Bar
Non-metallic materials and components comply with BS6920 at 65°C
Range of single hole, single outlet (swivel) combination tap assemblies, (brass bodies – various finishes), incorporating quarter turn ceramic disc headworks with single lever operating members. The spout outlets incorporate plastic aerators. Maximum working pressure 10.0 Bar Maximum working pressure 10.0 Bar
Non-metallic materials and components comply with BS6920 at 60°C
Range of single hole, single outlet (swivel) combination tap assemblies (brass bodies – various finishes), incorporating a ceramic cartridge headwork with single lever operating member. The spout outlet incorporates a plastic aerator. Maximum working pressure 10.0 Bar. Maximum operating temperature 70°C Models added October 2024: Maximum operating temperature 60.0°C
Non-metallic materials and components comply with BS6920 at 70°C
Single hole, single outlet (swivel) combination tap assembly (various finishes), incorporating a ceramic cartridge headwork with a single lever operating member. The spout outlet incorporates a plastic aerator. Maximum working pressure 10.0 Bar.
Non-metallic materials and components comply with BS6920 at 65°C
Range of wall mounted, two-hole, single outlet (fixed) combination tap assemblies (chrome plated brass), incorporating ceramic cartridge headworks with single lever operating members. The spout outlets incorporate plastic aerators. Maximum working pressure 10.0 bar. Maximum operating temperature 65°C.
Range of two hole, single outlet (fixed) combination tap assemblies (chromium plated brass) incorporating quarter turn ceramic disc headworks with single lever operating members (310805) or cross top operating members (771429). The spout outlet incorporates a plastic flow straightener and a combined NBR washer and stainless steel strainer. The products are supplied with metal backnuts. Maximum working pressure 10.0 bar. Maximum operating temperature 65°C.
Range of Two hole, metal, single outlet, fixed combination tap assemblies with brass bodies (chrome plated), incorporating quarter turn ceramic disc headwork with single lever operating members. Spout outlets incorporate plastic flow straightners. Maximum working pressure 10.0 bar.
Non-metallic materials and components comply with BS6920 at 60°C
A range of wall mounted, two-hole, single outlet (fixed) combination tap assemblies (brass body, various finishes) incorporating a ceramic cartridge headwork with single lever operating member. The spout outlet incorporates a plastic aerator. Maximum working pressure 10.0 Bar
Non-metallic materials and components comply with BS6920 at 60°C
Range of two-hole, single outlet (fixed) combination tap assemblies (chromium plated brass), incorporating quarter turn ceramic disc headworks and a manual diverter to shower outlet. The spout outlet incorporates a plastic flow straightener. Products are supplied with a shower hose and handset and plastic or metal back nuts. Maximum working pressure 6.0 Bar. Maximum operating temperature 60°C.
Two-hole, single outlet fixed combination tap assembly (chrome plated brass), incorporating a two-way manual diverter valve controlling the flow and the temperature is controlled independently via a thermostatic cartridge incorporating dome type operating members which incorporates a manual override. The spout outlet incorporates a plastic flow straightener. The inlets incorporate a stainless-steel strainer and an approved check valve cartridge (however, the complete assembly has not been fully tested to demonstrate that it provides adequate backflow protection) and it is supplied with metal back nuts. Maximum working pressure 5.0 bar.
Non-metallic materials and components comply with BS6920 at 60°C
Wall mounted, two-hole, single outlet fixed combination tap assembly (chrome plated brass), incorporating a two-way manual diverter valve controlling the flow and the temperature is controlled independently via a thermostatic cartridge incorporating dome type operating members which incorporates a manual override. The spout outlet incorporates a plastic flow straightener. The inlets incorporate a stainless-steel strainer and an approved check valve cartridge (however, the complete assembly has not been fully tested to demonstrate that it provides adequate backflow protection). Maximum working pressure 5.0 bar.
Non-metallic materials and components comply with BS6920 at 60°C
Range of two-hole, single outlet (swivel) combination tap assemblies (chrome plated brass bodies), incorporating quarter turn ceramic discs headworks with either single lever, cross top, or dome type operating members. The spout outlet incorporates a plastic flow straightener. Supplied with metal backnuts. Maximum working pressure 10.0 Bar
Non-metallic materials and components comply with BS6920 at 65°C
Deck mounted two-hole, single outlet, fixed combination tap assembly (chrome plated brass) incorporating a quarter turn ceramic disc headwork with a single lever operating member. The temperature is controlled independently via a thermostatic cartridge incorporating a single lever operating member and a manual override button. The spout outlet incorporates a lockable diverter to shower outlet and a plastic aerator. The inlets incorporate EPDM washers and approved check valve cartridges, (however, the complete product has not been fully tested to demonstrate it provides backflow protection). Maximum operating pressure 5.0 bar
Non-metallic materials and components comply with BS6920 at 60°C
Range of two hole, single outlet (fixed) combination tap assemblies (chromium plated brass) incorporating quarter turn ceramic disc headworks with dome operating members and lockable diverter to shower outlet. The spouts incorporate plastic flow straightener and supplied with plastic backnuts. These products are not supplied with shower hose or handset. Maximum working pressure 10.0 bar.
Non-metallic materials and components comply with BS6920 at 60°C
Wall mounted, three-hole, single outlet (fixed) combination tap assembly incorporating a brass body with quarter turn ceramic disc headworks with single lever operating members. The spout outlet incorporates a plastic aerator.. Maximum working pressure 5.0 Bar.
Non-metallic materials and components comply with BS6920 at 60°C
Range of wall mounted, three-hole single outlet combination tap assemblies (various finishes), incorporating quarter turn ceramic disc headworks with dome type operating members. The spout outlets for models (V117 XX and V120 XX) incorporate plastic aerators and model (V147 XX) incorporates a plastic flow straightener. The spout inlet incorporates an approved check valve cartridge; however, the complete product has not been fully tested to demonstrate it provides backflow protection. Maximum working pressure 5.0 Bar
Non-metallic materials and components comply with BS6920 at 60°C
Range of wall mounted, three-hole, single outlet (fixed) combination tap assemblies (brass body with various finishes) incorporating quarter turn ceramic disc headworks and cube type operating members. The spout outlet incorporates a plastic aerator. Maximum working pressure 10.0 bar.
Non-metallic materials and components comply with BS6920 at 65°C
Range of three-hole, single outlet (swivel) combination tap assemblies (brass bodies, various finishes). Incorporating quarter turn ceramic disc headworks incorporating single lever, dome, or cross top type operating members (see models) and supplied with stainless steel braided EPDM lined connection hoses. The spout outlet incorporates a plastic aerator. The spout and side valves are connected via stainless steel braided EPDM lined flexible hoses with EPDM washers and O-rings. Maximum working pressure 5.0 Bar
Non-metallic materials and components comply with BS6920 at 65°C
A deck mounted, three-hole, single outlet (swivel) combination tap assemblies with brass bodies (various finishes). Incorporating quarter turn ceramic disc headworks with cross top operating members. The product is also supplied with stainless steel braided, EPDM lined flexible connecting hose assemblies, intended for use between side body valves and spout. The spout outlet incorporates a plastic flow straightener. Maximum working pressure 5.0 Bar
Non-metallic materials and components comply with BS6920 at 65°C
Range of four-hole, single outlet (swivel) combination tap assemblies (various finishes, see models), incorporating quarter turn ceramic disc headworks with a variety of operating members (see models) and a self-cancelling diverter to shower outlet. The spout outlets incorporate plastic flow straightener. Maximum working pressure 5.0 Bar
Non-metallic materials and components comply with BS6920 at 60°C
Range of deck mounted, three-hole, combination tap assemblies, (various finishes - see model), comprising of two ceramic cartridge headworks each with a single lever operating member. The product is supplied with stainless steel braided thermoplastic silicone (TPSiV) lined flexible connection hoses and a nylon braided silicone lined flexible hose assembly, which connects to a shower hose (brass double interlocked, PEX lined) and a deck mounted shower handset. Spout not supplied. Maximum working pressure 5.0 bar. Maximum operating temperature 60°C.
Wall mounted, two-hole, single outlet fixed combination tap assembly (chrome plated brass), incorporating a two-way manual diverter valve controlling the flow from the spout to overhead shower with a dome type operating member. The temperature is controlled independently via a thermostatic cartridge incorporating a dome type operating member that also incorporates an override button. The spout outlet incorporates a plastic flow straightener and a self-cancelling diverter to the shower outlets. The inlets incorporate a stainless-steel strainer and an approved check valve cartridge (however, the complete assembly has not been fully tested to demonstrate that it provides adequate backflow protection). Maximum working pressure 5.0 bar.
Non-metallic materials and components comply with BS6920 at 60°C
Range of four-hole, single outlet combination tap assemblies with various finishes (see models) Incorporating a ceramic cartridge headwork controlling the flow to the shower handset and quarter turn ceramic headworks controlling flow to the spout outlet, all with single lever operating members. The product is supplied with a shower hose and handset, the handset incorporates a single check valve on the inlet, however, the complete product has not been fully tested to demonstrate it provides backflow protection. Maximum working pressure 10.0 bar.
Non-metallic materials and components comply with BS6920 at 60°C
Range of floor mounted, swivel, bath mixers (brass or stainless-steel bodies - variety of finishes (see models), incorporating ceramic cartridge headworks with single lever operating members. The spout outlets incorporate plastic aerators. The products also incorporate self-cancelling diverters to a shower handset. The diverter outlets incorporate an approved check valve cartridges, however, the complete products have not been fully tested to demonstrate they provide backflow protection. Maximum working pressure 5.0 Bar.
Non-metallic materials and components comply with BS6920 at 60°C
Range of wall mounted brass bodied spout outlets (various finishes, see model) incorporating a plastic aerator. Maximum working pressure 10.0 Bar
Non-metallic materials and components comply with BS6920 at 60°C
‘Super Speedfit’ range of plastic pushfit fittings (black, light grey, dark grey, white, natural, and red) for use with John Guest LLDPE tubing (blue, black, natural, green, orange, red, white and yellow). Operating parameters: 5/32”, ¼”, 5/16”, 4mm & 6mm = 16.0 bar cold water & 8.0 bar at 65°C. 3/8” = 10.0 bar cold water & 7.0 bar at 65°C. ½” = 10.0 bar cold water & 6.0 bar at 65°C. 8mm, 12mm & 15mm = 10.0bar cold water & 6.0 ba at 65°C. 10mm = 10.0bar cold water & 7.0 bar at 65°C.
‘Flowflex’ and ‘Lamontite’ ranges of brass, chromium plated brass, nickel plated brass and DZR brass compression fittings for use with copper pipe (manufactured to to BS EN1057:2006 + A1:2010). Maximum working pressure 16.0 bar. Maximum operating temperature 99°C.
Primaflow ranges of brass, DZR brass, chromium plated brass, nickel plated brass and DZR brass compression fittings for use with copper pipe to BS EN 1057. Maximum working pressure 16.0 bar. Maximum operating temperature 99°C.
Range of ‘Superseal’ and ‘Speedfit’ push-fit fittings with acetal body’s (black or light grey) and NBR ‘O’ rings. For use with John Guest LLDPE tubing (Speedfit port only) and 316 stainless steel tubing manufactured to EN10088 (Superseal push-fit port only). Pipe inserts must be used for the LLDPE tube sizes 3/8” and ½”. Maximum working pressure: See models below. For cold water use only.
Range of copper end feed fittings for use with copper tube. For above and below ground use. Maximum working pressure 25.0 bar. Maximum operating temperature 99°C.
Page 90 of 233
We use cookies to give you the best possible experience with WRAS. Some are essential to provide website functions and ensure the website is secure. We also use cookies to help us understand how people use the site and to make improvements. Click "Accept All" to enable recommended settings or click "Manage cookies" to adjust your settings. For more details, see our Cookie Policy.
