Range of in-line, manually adjustable pressure reducing valves with stainless-steel bodies and EPDM o-rings. The valves incorporate a stainless-steel strainer. Maximum inlet supply pressure 25.0 Bar. Outlet pressures between 1.5 bar and 6.0 bar. Cold water use only.
Range of latching (LV), proportional (PV), servo (SV), pilot (EV) solenoid valves with natural (appear white), plastic bodies. Valves with black coloured plastic bodies (incorporating a biocide) were added to the approval in January 2026. Pushfit models are for use with John Guest LLDPE and DMFIT LLDPE pipes. The inlets and outlets of all models are available with plastic flow regulators or plastic or copper strainers. All valves have a maximum working pressure of 10.0 bar. The bodies of valves with a silicone diaphragm are marked with an ‘S’ at the end of the model, e.g. ‘EV118/AS’ and have a maximum operating temperature 85°C. Valves with an EPDM diaphragm are for cold water use only and do not include this ‘S’ marking.
Range of pressfit connection spherical valves incorporating DZR brass bodies, PTFE seat and packing, NBR ‘O’-rings and various operating members: lever, lever lockable, T-handle and butterfly. For use with copper pipe (manufactured to BS EN 1057), stainless steel pipe (manufactured to BS EN 10312) and carbon steel pipe (ISO 4200 Groupe 1 Series 3). Maximum working pressure 16.0 bar. Maximum operating temperature 99°C.
Range of spherical valves incorporating a chrome plated brass body & brass ball. Maximum operating pressure 10 bar. Maximum operating temperature 65 °C.
Range of single lever or butterfly handle operated spherical valves with chrome plated brass bodies incorporating chrome plated brass ball. Maximum working pressures: see model below. Maximum operating temperature 23°C.
Range of press fit ball valves with DZR brass bodies incorporating a chrome plated brass ball. To be used with copper pipe EN1057 only. Crimp joint is achieved by a M profile crimp. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Range of spherical valves with PVC-U or ABS bodies and ball (see models).. PVC-U models with a solvent weld pipe connection are for use with PVC-U pipe (manufactured to ISO 1452) and are supplied with a PVC-U solvent cement. ABS models with a solvent weld pipe connection are for use with ABS pipe (manufactured to ISO 15493) and are supplied with an ABS solvent cement. Maximum working pressure 16.0 Bar. Cold water use only.
Range of gate valves with blue or red epoxy coated ductile iron bodies, incorporating ductile iron wedges encapsulated in EPDM and hand wheel operating members. Maximum working pressure - 16 Bar.
Non-metallic materials and components comply with BS6920 at 85°C
Range of resilient seated gate valves with blue epoxy coated ductile iron bodies and ductile iron wedges encapsulated in EPDM. The valve is operated via a non-rising spindle. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Range of Gate valves with ductile iron bodies (blue epoxy coated), EPDM rubber coated wedges, non-rising spindles with hand wheel operating members. Maximum working pressure 16.0 Bar Maximum operating temperature 85.0°C
Range of gate valves with bronze bodies and wedges. The valves are operated via a non-rising spindle with a hand wheel operating member. Maximum working pressure: 25 Bar. Maximum operating temperature: 85°C.
Ranges of gate valves with ductile iron bodies (blue epoxy coated), and EPDM coated wedge with hand wheel operating members. Maximum working pressure 16.0 Bar. Maximum operating temperature 85.0°C.
Range of gate valves with ductile iron bodies (blue epoxy coated), EPDM rubber coated wedges and hand wheel operating members. Maximum working pressure: 16.0 Bar. Maximum operating temperature: 80°C.
Range of wall mounted flow control valves with (brass bodies – various finishes) incorporating quarter turn ceramic disc headworks. The product is supplied with various trim sets incorporating a cross top, lever or dome type operating member. Maximum operating pressure 5 bar. Maximum operating temperature 60°C.
Range of angled stop valves, (chromium plated brass bodies) with dome operating members. Maximum working pressure 5.0 bar. Maximum operating temperature 85°C
Range of screw down stop valves with plastic bodies for below ground use.. The valves are supplied with loose pipe inserts and are for use with polyethylene pipe (manufactured to BS EN 12201). Maximum working pressure 14.0 bar. Cold water use only.
Range of manually operated balancing valves with DZR brass bodies. The product also incorporates a spherical valve. Maximum working pressure: 10 bar Maximum working temperature: 100°C.
Range of in-line electrolytic scale reducers with copper bodies for use with copper pipe (manufactured to BS EN 1057). Maximum working pressure 10.0 bar. Maximum operating temperature 40°C.
Oasis Kalix range of water dispensers which dispenses hot and cold water. The flow is controlled via a solenoid valve and the products are activated via a push button or infrared sensor. The products incorporate a pressure relief valve with a plastic body which is rated at 5.0 bar. Maximum working pressure 3.0 bar Please refer to model for maximum operating temperature.
Range of commercial and domestic ion exchange water softeners (salt regenerated). Operation is by an electronically controlled ion exchange resin filled plastic pressure vessel with integral salt cabinet (domestic models) or separate brine tank (commercial models). Maximum working pressure 8.0 bar. Cold water use only.
'POM NW-02 (432U slate grey)'. Dark grey coloured, injection moulded POM material. For use with water up to 65°C.
'ABS757K (9M cool grey) & ABS757K (432U slate grey)'. Light grey or dark grey coloured, injection moulded ABS materials. For use with water up to 65°C.
'H/E16018'. Factory applied, dark blue coloured electrostatic enamel coating. Apply as per manufacturer's TDS '00', dated '30.08.2017' and cure for 4.5 minutes at a peek temperature of 850°C. For use with water up to 85°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'KOROGUARD 20 RED & GREY'. Factory applied, two-component epoxy coatings available in red and grey. Mix parts A & B in a 3:1 volume ratio and apply as per manufacturer's TDS dated 'Jan 2024'. Cure for 7 days@30°C. For use with water up to 23°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'APLICAPROOF PUA P'. Factory applied, two component, grey coloured polyurea coating. Mix components A & B in a weight ratio of 1:1 and apply as per manufacturer's TDS 'Rev - 06/2024'. Cure for 48 hours@23°C. Between September 2022 and August 2024, the coating is for use with water up to 23°C. From September 2024, the coating is for use with water up to 60°C. This material is only approved for the mixing, curing & soaking conditions that appear on the approval. If the mix/cure/soak conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'APLICAPROOF PU W'. Factory applied, two-component, cream coloured (once mixed and applied) polyurethane resin coating. Mix components A & B in a 4:1 volume ratio and apply as per manufacturer's TDS 'Rev -06/2024'. Cure for 6 hours@23°C. For use with water up to 23°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the materials are not covered by the scope of the approval.
'Hempadur 35560 Cream Coating with Hempadur 15590 Red Primer'. Factory applied, cream coloured, two-component epoxy coating for use with epoxy primer. ‘Hempadur 15590 Red Primer’ is a two-component primer to be mixed in a 15:4 volume ratio and applied as per manufacturers PDS dated ‘October 2024’. Cure for 16 hours@20°C. 'Hempadur 35560 Cream’ is a two-component coating to be mixed in a 6.8:2 volume ratio and applied as per manufacturers PDS dated ‘May 2024’. Cure for 7 days@20°C. For use with water up to 35°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'P • HSR42.5'. Factory applied, grey coloured Sulphate resistant Portland cement. Mix cement:medium sand:water in 1:1.4:0.45 weight ratio and apply as per manufacturer's instructions 'Version 03', dated '29th-07-2024'. Cure for 3 hours at 25°C. For use with water up to 65°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Enviroline 2405'. Site applied, off-white coloured (once mixed and applied), two-component epoxy. Mix parts A (light grey, opaque liquid) and B (white, opaque liquid) in a volume ratio of 2:1 and apply as per manufacturer's TDS 'Ref:10139', 'Issue Date:8/21/2017'. Cure for 7 days@25°C. For use with water up to 23°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'UW TPE HEA-ISO (manufactured from NAKAN HEA 407 EX)'. White coloured (translucent), extruded TPE hose. Shore hardness 66. Tested in-radius size 0.39mm. For use with water up to 65°C.
'ULTRAMID® A3EG7 AQUA BLACK 00564'. Black coloured, injection moulded PA material. For use with water up to 85°C.
'ULTRAMID® B3EG3 AQUA BLACK00564'. Black coloured, injection moulded PA material. For use with water up to 85°C.
'DZT PANT I1000-NC; DZT PANT I10G05-NC; DZT PANT I10G10-NC; DZT PANT I10G15-NC; DZT PANT I10G20-NC; DZT PANT I10G25-NC; DZT PANT I10G30-NC; DZT PANT I10G35-NC; DZT PANT I10G40-NC; DZT PANT I10G45-NC; DZT PANT I10G50-NC; DZT PANT I10G55-NC; DZT PANT I10G60-NC; DZT PANT I10G65-NC (un-pigmented - appears beige)’. ‘DZT PANT I10G05-BK; DZT PANT I10G10-BK; DZT PANT I10G15-BK;DZT PANT I10G20-BK;DZT PANT I10G25-BK; DZT PANT I10G30-BK; DZT PANT I10G35-BK;DZT PANT I10G40-BK;DZT PANT I10G45-BK; DZT PANT I10G50-BK; DZT PANT I10G55-BK; DZT PANT I10G60-BK; DZT PANT I10G65-BK (black coloured)'. Injection moulded PA materials. For use with water up to 85°C.
'GUR® 4012, GUR® 4012 ECO-B, GUR® 2105, GUR® 2105 ECO-B, GUR® 2122, GUR® 2122 ECO-B, GUR® 2126, GUR® 2126 ECO-B, GUR® 4017, GUR® 4017 ECO-B GUR® 4018, GUR® 4018 ECO-B, GUR® 4120, GUR® 4120 ECO-B, GUR® 4150, GUR® 4150 ECO-B, GHR® 8020 & GHR® 8020 ECO-B’. Natural (material appears white/cream coloured, opaque) compression moulded UHMW-PE materials. ‘GUR® 2105, 2105 ECO-B, 2122, 2122 ECO-B. 2126, 2126 ECO-B’ are for use with water up to 60°C. ‘GUR® 4017, 4017 ECO-B, 4018, 4018 ECO-B 4012, 4012 ECO-B, 4120, 4120 ECO-B, 4150, 4150 ECO-B, GHR® 8020 & 8020 ECO-B' are for use with water up to 85°C.
'Ultrason® S2010 G4 Schwarz 15038'. Black coloured, injection moulded polysulphone material. For use with water up to 85°C.
'Steckkörper 2675 Fitting'. White coloured (opaque), PVDF component injection moulded from 'amboflon® PVDF 24'. For use with water up to 85°C.
'ME0940/40 - 90'. Black coloured, injection moulded EPDM rubber material. Shore hardness between 40 & 90. Tested in-radii sizes between 1.0mm & 3.0mm. For use with water up to 85°C.
'FKM 70 Green M403'. Green coloured, injection moulded FKM 'O' rings. Shore hardness 70. Tested in-radius size 2.66mm. For use with water up to 23°C.
'13K0705 NOK 'O' ring'. Red/brown coloured, compression moulded FKM rubber 'O' ring. Shore hardness 70. Tested in-radius size 1.24mm. For use with water up to 75°C.
'SU26F415H01 'O' ring'. Black coloured, compression moulded FKM rubber 'O' ring. Shore hardness 80. Tested in-radius size 0.9mm. For use with water up to 75°C.
'V8 Fluorocarbon Rubber Bellows'. Black coloured, injection moulded fluorocarbon rubber bellows. Shore hardness 70. Tested in-radii sizes between 0.7mm & 4.1mm. For use with water up to 85°C.
'NBR 70 M332 'O' rings'. Black coloured, injection moulded NBR 'O' rings. Shore hardness 70. Tested in -radius size 3.0mm. For use with water up to 45°C.
'Silicone Rubber Washer SIL40 (SIL4001)'. Black coloured, vulcanised silicone rubber washer. Shore hardness 40. Tested in-radius size 0.56mm. For use with water up to 85°C.
'Type 1 O-ring, T056D 124H16 Model Code P16'. Cream coloured (opaque), compression moulded silicone rubber 'O' ring. Shore hardness 70. Tested in-radius size 1.2mm. For use with water up to 85°C.
'Tangit Rapid'. Straw coloured adhesive intended to join pipe and fittings. Apply as per manufacturer’s instructions ‘TFU_TM_GB_0915’. Cure for 24 hours@23°C. For use with water up to 23°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Fosroc Nitoseal SC600'. Site applied, grey coloured silicone sealant waterstop. Apply as per manufacturer's TDS issue '1.0', dated October 2024. Cure for 21 days at 7°C. For use with water up to 23°C. This material is only approved for the mixing & curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval. These materials are for use in concrete reservoirs and similar structures, constructed in accordance with the design criteria of BS EN 1992-3:2006 (Design of concrete structures – Liquid retraining and containing structures) with respect to normal frequency of joints. The material has been tested at a reduced surface area to volume ratio of 1000mm² per litre.
'Penosil PVC Pipe Adhesive 935 & Penosil Adhesivo PVC-U A-35'. Clear (transparent) solvent cements intended to join PVC pipe and fittings. Apply as per manufacturers technical data sheet. Cure for 48 hours@23°C. For use with water up to 23°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Eco Pipeliner- DWP024'. White coloured (opaque), extruded PVC pipeliner. For use with water up to 23°C.
Range of wall mounted, two-hole, single outlet (fixed) electronically controlled tap assemblies (chromium plated brass). The flow is controlled by a solenoid valve activated via infra-red sensor. Temperature is controlled independently via a thermostatic cartridge with a dome operating member which incorporates a manual override button. The spout outlets incorporate plastic aerators, and both inlets incorporate an approved single check valve cartridge (however, the complete assembly has not been fully tested to demonstrate that it provides adequate backflow protection) and stainless-steel strainers. Maximum working pressure 10.0 Bar. Maximum operating temperature 60.0°C.
Range of deck mounted, single hole, single outlet (fixed) electronically controlled tap assemblies (chromium plated brass). Flow is controlled by a solenoid valve activated via an infra-red sensor. The spout outlet incorporates a plastic aerator. The main body incorporates a plastic flow regulator and stainless steel strainer prior to the solenoid. The inlets to the main body of the GS10, CM10 & GH10 model variants incorporate approved check valve cartridges, however, the complete product has not been fully tested to demonstrate it provides backflow protection. These models also have a manual temperature control operated by a single lever on the side of the body. The inlet hoses incorporate a TPE gasket. The models are supplied with or without a pop-up waste. The GS20 & GM20 model variants are single feed. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.
Page 86 of 131
We use cookies to give you the best possible experience with WRAS. Some are essential to provide website functions and ensure the website is secure. We also use cookies to help us understand how people use the site and to make improvements. Click "Accept All" to enable recommended settings or click "Manage cookies" to adjust your settings. For more details, see our Cookie Policy.
