Kuterlite K900 Pro range of compression fittings with DZR brass bodies for use with copper pipe (EN 1254) Maximum working pressure for 8mm-10mm = 70.0 bar. Maximum working pressure for 12mm – 28mm = 20.0 bar. Maximum working pressure for 35mm – 54mm = 6.0 bar. Maximum operating temperature 90°C.
Range of copper and DZR brass press fit tap connectors for use with copper tube (manufactured to EN1057). Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Range of end feed brass fittings for use with copper tube (manufactured to EN 1057). The HLE20CB-d tank connector incorporates an EPDM washer. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Range of end feed copper fittings for use with copper tube to EN 1057. The HLDPMFWT and HLDPMFZT models incorporate a captive nut on one end with a fibre gasket washer. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Range of end feed copper or gunmetal solder fittings for use with copper pipe. Maximum working pressure 16.0 bar (Sizes 8 - 28mm). Maximum working pressure 10.0 bar (Sizes 35 - 108mm). Maximum operating temperature 100°C.
Range of copper end feed fittings for use with copper tube. For above and below ground use. Maximum working pressure 25.0 bar. Maximum operating temperature 99°C.
Range of dual flush WC outlet valves, incorporating ABS body, silicone seal & internal overflow. Cold water use only.
WC dual flush outlet valve comprising of ABS plastic body, EPDM gasket and an internal overflow. Cold water use only
Range of heat exchangers connected to copper waste pipe, Where the waste is discharged down a “rotator” into a copper waste pipe, and potable water is returned to the shower/heating device via a copper double walled jacket around the copper waste pipe. Maximum working pressure 8.0 bar. Maximum operating temperature 60°C
Range of 4 or 6 port manifolds with or without water meter manifolds (see model), all with gunmetal bodies. Models with a water meter manifold incorporate a quarter turn stop valve or screw down stop valve (see model), and an approved check valve cartridge however, the complete product has not been fully tested to demonstrate it provides backflow protection. Maximum working pressure 16.0 bar. Cold water use only.
Manifold comprising of a PVC-U stub flange, PVC-U pipe and PVC-U tee fitting. Maximum working pressure 8.0 bar. Cold water use only.
Y type fittings incorporating brass body and NBR washer. Maximum working pressure 10.0 bar. Maximum operating temperature 85°C.
Range of brass (chrome plated) quick fit connectors. Maximum operating temperature 60°C
‘3ME’ Range of horizontal pumps with stainless steel bodies and impellers, and EPDM ‘O’-rings. The products are supplied with a carbon/ceramic/EPDM shaft seal. Maximum working pressure 10.0 bar. Maximum operating temperature 100°C.
Range of shower heads, shower handsets and shower kits incorporating either brass or plastic bodies (various finishes). The inlets of the shower handsets incorporate a stainless-steel strainer. Models ORA-MFSRKWOP-RO-CP, NEB-MFSRKWO-RO-CP & EVO-MFSRKWO-CP are supplied with a shower hose and riser rail. Maximum operating temperature 60°C.
Range of overhead shower outlets with brass bodies (various finishes - see model). Model 27 390 xxx is ceiling mounted. Model 27 437 xxx is wall mounted. The inlet incorporates stainless steel strainer and an approved check valve cartridge however, the complete product has not been fully tested to demonstrate it provides backflow protection. Maximum operating temperature 60°C.
Shower kit consisting of chrome plated shower handset, shower hose and riser rail. Maximum operating temperature 60°C.
Range of handshower holders with brass bodies (various finishes). The outlet incorporates an approved check valve cartridge, however, the complete product has not been fully tested to demonstrate it provides backflow protection. Maximum operating temperature 65°C
Range of shower heads with brass bodies (various finishes), incorporating EPDM ‘O’-rings and plastic flow regulator. Maximum operating temperature 60°C.
Range of shower outlets with matte black finishes, consisting of a shower hose, handset, riser rail and a brass wall mounted inlet. Maximum operating temperature 60°C.
Range of shower handsets (various finishes) incorporating stainless steel strainers. Model 28 588 xxx incorporates flow regulator. Maximum operating temperature 60°C.
Range of showers handsets incorporating plastic bodies (chrome plated) Maximum operating temperature 60°C.
Range of Y type strainers with blue epoxy coated ductile iron bodies and EPDM ‘O’-rings. Maximum working pressure 25.0 bar. Maximum operating temperature 85°C
Range of Y type strainers with blue epoxy coated ductile iron bodies and EPDM ‘O’-rings. Maximum working pressure 25.0 bar. Maximum operating temperature 85°C
Range of Y type strainers with blue epoxy coated ductile iron bodies and EPDM ‘O’-rings. Maximum working pressure 25.0 bar. Maximum operating temperature 85°C
Range of Y type strainers with blue epoxy coated ductile iron bodies and EPDM ‘O’-rings. Maximum working pressure 25.0 bar. Maximum operating temperature 85°C
Range of drain taps incorporating brass bodies, EPDM seats and washers and a non-rising spindle headwork. Maximum working pressure 10.0 bar. Maximum operating temperature 85°C.
Range of drain taps incorporating brass bodies, EPDM seats and washers and a non-rising spindle headwork. Maximum working pressure 10.0 bar. Maximum operating temperature 85°C.
Range of pillar taps (chrome plated brass) incorporating quarter turn ceramic disc headworks with cross-top operating members. The product is supplied with metal backnuts. Maximum working pressure 10.0 bar. Maximum operating temperature 65°C.
Range of pillar taps (chrome plated brass) with quarter turn ceramic disc headworks and single lever operating members. The products are supplied with metal backnuts. Maximum working pressure 10.0 bar. Maximum operating temperature 65°C.
Range of pillar taps incorporating brass bodies (chrome plated), and quarter turn ceramic disc headowks. The spout outlet incorporates a flow straightener. Maximum working pressure 6.0 bar. Maximum operating temperature 60°C.
Range of pillar taps (chromium plated brass). The 595-H1 & K-595-H2 models incorporate a quarter turn ceramic disc headwork with a single lever operating member. The K-595M prefix models incorporate a non-rising spindle headwork with dome type or cross top (see model) operating member. The spout outlet incorporates a plastic flow straightener. The product is supplied with metal back nuts. Maximum working pressure 10.0 bar. Maximum operating temperature 85°C.
Pillar tap (chromium plated brass), incorporating quarter turn ceramic disc headwork with single lever operating member and plastic back nuts. The spout outlets incorporate a plastic flow straightener. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.
Range of stainless steel braided HDPE lined flexible hose assemblies with various end connections. Maximum working pressure 10.0 bar. Maximum operating temperature 85°C.
Range of stainless-steel interlocked shower hoses (various finishes (see model) incorporating an EDPM liner and NBR washers. Maximum working temperature 85°C
Range of automatic air venting valves with DZR brass bodies. Maximum working pressure 16.0 bar. Maximum operating temperature 60°C.
Range of wall mounted, concealed, manual blending shower valves with brass bodies and trim set (various finishes). The flow is controlled independently to one or two separate outlets via ‘detent’ (push to on push to off) headworks (see model). Temperature is controlled via a ceramic cartridge. The inlets incorporate single check valve cartridges however, the complete product has not been fully tested to demonstrate it provides backflow protection. Maximum working pressure 10.0 bar. Maximum operating temperature 70°C.
Wall mounted manual blending shower valves with brass bodies (various finishes - see model) incorporating a ceramic cartridge headwork with a single lever operating member. The outlet incorporates an approved check valve cartridge, however, the complete product has not been fully tested to demonstrate it provides backflow protection. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.
Wall mounted manual blending shower valves with brass bodies (various finishes - see model) incorporating a ceramic cartridge headwork with a single lever operating member. The outlet incorporates an approved check valve cartridge with an integral plastic flow regulator, however, the complete product has not been fully tested to demonstrate it provides backflow protection. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.
Wall mounted manual blending shower valve with a brass body (various finishes - see model) incorporating a ceramic cartridge headwork with a single lever operating member. The outlet incorporates an approved check valve cartridge, however, the complete product has not been fully tested to demonstrate it provides backflow protection. Maximum working pressure 5.0 bar. Maximum operating temperature 60°C.
Concealed, wall mounted, electronically controlled blending valve (brass body). Flow is controlled via a solenoid valve activated via an infra-red sensor. The temperature is controlled independently via a ceramic cartridge headwork with a circular operating member. The inlets to the sensor box incorporate stainless steel strainers. Maximum working pressure 5.0 bar. Maximum operating temperature 70°C.
Range of wall mounted, concealed thermostatic shower valves, brass bodies with either (chrome or matte black finishes), incorporating two-way diverter valves and quarter turn ceramic disc headworks controlling the flow with either single lever or cross-top operating members. The temperature is controlled independently via a thermostatic cartridge with either a cross-top or dome operating member, both incorporating a manual override button. The product incorporates a single check-valve cartridge assembly incorporating a stainless-steel strainer; however, the complete product has not been fully tested to demonstrate backflow protection. Maximum working pressure 10.0 bar. Maximum operating temperature 80°C.
Wall mounted concealed thermostatic shower valve, incorporating a two-way manual diverter controlling the flow with a single lever operating member. The temperature is controlled independently via a thermostatic cartridge with a dome operating member incorporating a manual override button. The product incorporates a single check valve cartridge assembly incorporating a stainless-steel strainer, however; the complete product has not been fully tested to demonstrate backflow protection. Maximum working pressure 10.0 bar. Maximum operating temperature 80°C.
Range of wall mounted thermostatic shower valves (chrome plated brass). Models PM2 CSHCVO C and N2 CSHCVO C incorporate a non-rising spindle headwork controlling the flow with single lever operating members. The temperature is controlled independently via a thermostatic cartridge with single lever operating member (PM2 CSHCVO) or a cross top operating member for (N2 CSHCVO C). Model PM2 SQSHCVO C incorporates a thermostatic cartridge that controls both flow and temperature with a single lever operating member. The inlets for all models incorporate flow regulators and approved check valve cartridges, (however, the complete product has not been fully tested to demonstrate that it provides backflow protection). Maximum working pressure 10.0 Bar Maximum operating temperature 65°C.
Range of T-type mixing valves incorporating a DZR brass body (brushed chrome plated) and thermostatic cartridge. Maximum working pressure 10.0 bar. Maximum operating temperature 100°C.
RANGE OF THERMOSTATIC BLENDING VALVES INCORPORATING CHROME PLATED BRASS BODIES. THE INLET INCORPORATES A STAINLESS STEEL STRAINER AND AN APPROVED CHECK VALVE CARTRIDGE HOWEVER, THE COMPLETE PRODUCT HAS NOT BEEN FULLY TESTED TO DEMONSTRATE IT PROVIDES BACKFLOW PROTECTION. MODELS 09 415 IS SUPPLIED WITH A RIGID CONNECTION SET AND TEE PIECE AND MODEL 09 146 IS SUPPLIED WITH A PEX LINED FLEXIBLE HOSE AND TEE PIECE CONNECTION SET. MAXIMUM WORKING PRESSURE 10.0 BAR. MAXIMUM OPERATING TEMPERATURE 60°C.
Range of wall mounted (concealed) thermostatic mixing valves with brass bodies, incorporating half turn ceramic disc headworks controlling the flow with dome type operating members. Temperature is controlled independently via a thermostatic cartridge with a dome operating member and manual override button. Both inlets incorporate approved check valve cartridges, however, the complete product has not been fully tested to demonstrate it provides backflow protection. Maximum working pressure 5.0 bar. Maximum operating temperature 60°C.
Range of thermostatic blending valves incorporating chrome plated brass bodies. The inlet incorporates a stainless steel strainer and an approved check valve cartridge however, the complete product has not been fully tested to demonstrate it provides backflow protection. Models 09 415 is supplied with a rigid connection set and tee piece and model 09 416 is supplied with a PEX lined flexible hose and tee piece connection set. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.
Range of T-type thermostatic blending valves (chromium plated DZR brass body). The inlets incorporate stainless steel strainers and an approved check valve cartridge which has been verified by test as suitable for backflow protection against Fluid Category 2. Compression models are for use with copper pipe manufactured to EN1057. Maximum working pressure 10.0 bar. Maximum operating temperature 85°C.
Range of wall mounted thermostatic shower valves incorporating brass bodies (various finishes), self-cancelling diverter and self-closing headwork. Temperature is controlled independently via a thermostatic cartridge with a dome type operating member. Models 1.1967.001, 1.1967.002, 1.1967.003 & 1.1967.004 are supplied with a shower hose, handset and riser rail and overhead shower. Models 1.1967.005, 1.1967.006, 1.1967.007 & 1.1967.008 are supplied with a shower hose, handset, riser rail & bath filler. Models 1.1967.009, 1.1967.010 & 1.1967.011 are supplied with a shower hose, handset and riser rail, overhead shower & bath filler. Maximum working pressure 5.0 bar. Maximum operating temperature 50°C.
Page 71 of 226
We use cookies to give you the best possible experience with WRAS. Some are essential to provide website functions and ensure the website is secure. We also use cookies to help us understand how people use the site and to make improvements. Click "Accept All" to enable recommended settings or click "Manage cookies" to adjust your settings. For more details, see our Cookie Policy.
