Range of wall mounted combination boilers providing domestic hot water via a plate heat exchanger and pressurised central heating system. The primary circuit incorporates a pressure relief valve set at 3.0 bar and an expansion vessel. The products are supplied with a temporary filling loop which incorporates a combined isolation valve and double check valve assembly (suitable for backflow protection against Fluid Category 3), stainless steel braided EPDM lined flexible hose assembly and an isolation valve. The secondary circuit (DHW) incorporates a stainless-steel strainer. The primary circuit incorporates isolation valves on the flow and return. Maximum working pressures: DHW: 10.0 Bar CH:2.5 Bar Maximum operating Temperatures: DHW: 65.0°C CH: 85.0°C
‘Sonata’ range of water meters with plastic or brass/plastic bodies. Maximum working pressure 16.0 bar.
Non-metallic materials and components comply with BS6920 at 50°C
Range of inline water meters with blue epoxy coated cast iron body. Maximum working pressure 16.0 bar. Cold water use.
Range of water meters with blue epoxy coated ductile iron bodies, plastic measurement chambers and vanes and NBR ‘O’-rings. Maximum working pressure 16.0 bar. Maximum operating temperature 50°C.
Permanent filling devices for primary heating and chilled water closed circuits in domestic and non-domestic premises. The mains and closed circuit system pressures are continuously checked by two pressure sensors and their differential monitored by microprocessors. If the mains pressure is adequate and there is a drop in system pressure, then the two solenoid valves operate to allow water into the system via the transfer chamber. At all other times the normally open solenoid valve drains the transfer chamber to waste, via tundish (meeting the requirements of an air gap to drain), and allowing air to be admitted via an automatic air vent to create an atmospheric disconnection across the transfer chamber. Stainless steel strainer on the inlet supply. Mikrofill 3: Maximum working pressure 5.0 Bar. Cold water use only. Mikrofill 3 Pro (72846): Maximum working pressure 9.0 Bar. Cold water use only.
Flow meter with stainless steel body. Maximum working pressure 16.0 bar.
Non-metallic materials and components comply with BS6920 at 60°C
CMBE range of horizontal multistage centrifugal booster pumps with stainless steel bodies and impellers and EPDM ‘O’-rings. All models include an expansion vessel, non-return valve, pressure gauge and sensor on the outlet. Maximum working pressure 10.0 bar. Cold water use only.
Range of vertical multistage pumps with either stainless-steel bodies (“N” versions) or cast iron bodies with a black electrodeposition coating (“G” versions), stainless-steel impellers, shaft and outer sleeve. Maximum working pressure: NKV32 & NKV45 models - 32.0 bar, NKV65 & NKV95 models - 25.0 bar. Max operating temperature: Stainless steel (“N” versions) - 100°C. Cast iron (“G” versions) - Cold water use only.
Range of vertical multistage pumps with either stainless-steel bodies (“N” versions) or cast iron bodies with a black electrodeposition coating (“G” versions), stainless-steel impellers, shaft and outer sleeve. Maximum working pressure: FGV30, FGV45 - 32.0 bar, FGV65, FGV95 - 25.0 bar. Max operating temperature: Stainless steel (“N” versions) - 100°C. Cast iron (“G” versions) - Cold water use only.
Range of booster pumps with stainless steel bodies, plastic impellers, and NBR ‘O’-rings. The products incorporate a temperature sensor, pressure sensor, pressure vessel and a non-return valve integral to the pump chamber. Maximum working pressure 6.5 bar. Maximum operating temperature 75°C.
Range of overhead showers consisting of stainless steel bodies and silicone nozzles and gaskets and shower handsets consisting of ABS (LB-2003N, LB-2003, LB-2004) or brass bodies (LB-2006 & LB-2028).
Non-metallic materials and components comply with BS6920 at 60°C
Range of shower handsets & overhead shower outlets with chromium plated plastic body. The inlets of the overhead shower outlets incorporate a stainless-steel strainer.
Non-metallic materials and components comply with BS6920 at 60°C
Range of overhead shower outlets with (brass bodies – various finishes), incorporating EPDM `O`-rings and a plastic strainer. Open outlet use only.
Non-metallic materials and components comply with BS6920 at 60°C
Range of overhead shower outlets with brass or stainless-steel bodies (various finishes - see model), with NBR ‘O’-rings. The inlet incorporates a stainless-steel strainer.
Non-metallic materials and components comply with BS6920 at 70°C
Range of shower arms and elbows (brass bodies – various finishes). Maximum operating temperature: (T2064W) - 95.0°C (T2062W, T2069W & T2069SW) - 85.0°C (T2066W) - 60°C
Range of shower kits comprising of a chrome plated brass handset, shower hose and riser rail.
Non-metallic materials and components comply with BS6920 at 85°C
Range of overhead shower outlets with brass or stainless-steel bodies (various finishes - see model), with NBR ‘O’-rings. The inlet incorporates a stainless-steel strainer.
Non-metallic materials and components comply with BS6920 at 70°C
Range of overhead shower outlets with brass or stainless-steel bodies (various finishes - see model), with NBR ‘O’-rings. The inlet incorporates a stainless-steel strainer.
Non-metallic materials and components comply with BS6920 at 70°C
Ranges of shower kits comprising of a chrome plated plastic shower handset, brass wall elbow and either stainless steel interlocked, or PVC coated, shower hoses. Shower kits with ½” (M) inlets are also supplied with a brass wall elbow which incorporate a plastic flow regulator and an approved single check valve cartridge (however, the complete product has not been fully tested to demonstrate it provides backflow protection). Maximum operating temperature 60°C.
Range of shower heads with a chromium plated brass bodies, with stainless-steel strainer plastic flow regulator on the inlet. Models P42802 & P45300 have plastic bodies.
Non-metallic materials and components comply with BS6920 at 60°C
Range of hand shower outlets with chromium plated plastic bodies, stainless steel strainers and a plastic flow regulator.
Range of shower handsets with chrome plated plastic bodies. Some models incorporate a plastic aerator at the outlet of the shower and/or a plastic flow regulator and strainer on the inlet.
Non-metallic materials and components comply with BS6920 at 60°C
Range of overhead shower outlets with brass bodies (various finishes, see model), with stainless steel strainers and EPDM O-rings at the inlets. Models 26295W-** & 26295W-G-** are also supplied with flow regulators. Maximum operating temperature 60°C.
Range of stainless-steel braided EPDM lined flexible hose assemblies with a variety of end connections. Some models incorporate screwdriver operated isolation valves. Maximum working pressure 16.0 bar.
Non-metallic materials and components comply with BS6920 at 85°C
Range of stainless-steel braided EPDM lined flexible hose assemblies with a variety of end connections. Some models incorporate screwdriver operated isolation valves. Maximum working pressure 16.0 bar.
Non-metallic materials and components comply with BS6920 at 85°C
Range of stainless-steel braided EPDM lined flexible hose assemblies with a variety of end connections. Some models incorporate screwdriver operated isolation valves. Maximum working pressure 16.0 bar.
Non-metallic materials and components comply with BS6920 at 85°C
Range of 2 and 3 port manifold assemblies with brass bodies incorporating ‘Tectite Classic’ push-fit fittings for use with either copper pipe (manufactured to EN1057), PEX pipe (manufactured to BS7291-3:2010) or PB pipe (manufactured to BS7291-2). Maximum working temperature and pressure: Use with copper pipe: 16.0 bar @ 30°C, 10.0 bar @ 65°C & 6.0 bar @ 95°C. Use with PEX & Polybutylene: 12.0 bar @ 20°C, 6.0 bar @ 65°C & 3.0 bar @ 92°C.
Non-metallic materials and components comply with BS6920 at See description °C
Range of air release valves with blue epoxy coated ductile iron bodies, EPDM O-rings, seats and stainless-steel floats. Maximum working pressure 16.0 bar.
Non-metallic materials and components comply with BS6920 at 80°C
Wall mounted, manually operated shower mixers with brass bodies – various finishes, incorporating a ceramic cartridge headwork, and a single lever operating member. The outlet incorporates an approved check valve cartridge, however, the complete product has not been fully tested to demonstrate it provides backflow protection. Maximum working pressure 10.0 bar.
Non-metallic materials and components comply with BS6920 at 60°C
Range of deck mounted, manual blending valves, incorporating a ceramic cartridge headworks with a single lever operating member. The product is supplied with a stainless-steel braided, PEX lined flexible connection hose assembly that incorporates an approved check valve cartridge; however, the complete product has not been fully tested to demonstrate it provides backflow protection. The product is supplied with a hose and handset. Maximum working pressure 10.0 Bar
Non-metallic materials and components comply with BS6920 at 60°C
Range of wall mounted, manual blending shower mixers with (brass bodies - various finishes), incorporating a ceramic cartridge headwork and single lever operating member. The shower outlet incorporates an approved check valve cartridge, however, the complete product has not been fully tested to demonstrate it provides backflow protection. Maximum working pressure 10.0 Bar
Non-metallic materials and components comply with BS6920 at 60°C
Range of concealed thermostatic shower mixing valves with (brass bodies - various finishes), incorporating a ceramic disc diverter valve controlling the flow between two outlets. The temperature is controlled independently via a thermostatic cartridge with a manual override button. The products are supplied with trim sets and operating members in a various finishes. The 15 708 xxx model has cube type operating members, and all other models have single lever operating members. Both inlets incorporate an approved check valve cartridge (however, the complete product has not been fully tested to demonstrate it provides backflow protection) Maximum working pressure 10.0 Bar.
Non-metallic materials and components comply with BS6920 at 60°C
Range of concealed wall mounted thermostatic shower valves, (brass bodies – various finishes), incorporating quarter turn ceramic disc headworks controlling the flow. The temperature is controlled independently via a thermostatic cartridge, both using cubed type operating members. The inlets incorporate stainless steel strainer washers and approved single check valve cartridges; however, the complete product has not been fully tested to demonstrate it provides backflow protection. The products are supplied with a shower hose, handset, overhead shower, wall mounted shower outlet, wall mounted shower arm and a riser rail assembly. Maximum working pressure 5.0 Bar
Non-metallic materials and components comply with BS6920 at 60°C
Wall mounted thermostatic bar shower mixer, (chrome plated brass body) incorporating a quarter turn ceramic disc headwork with a dome type operating member. The temperature is controlled independently via a thermostatic cartridge with a dome type operating member that incorporates a manual override button. The inlets incorporates approved single check valve cartridges, however, the complete product has not been fully tested to demonstrate that it provides backflow protection. This product is supplied with a shower hose, handset and riser rail assembly. Maximum working pressure 5.0 Bar
Non-metallic materials and components comply with BS6920 at 65°C
Range of wall mounted thermostatic shower valves (chrome plated brass). Flow is controlled by a ceramic disc diverter cartridge, using dome type operating members. Temperature is controlled independently via a thermostatic cartridge using a dome type operating member which also incorporates a manual override button. Both inlets incorporate stainless steel strainers and approved check valve cartridges, however, the complete products have not been fully tested to demonstrate it provides backflow protection Maximum working pressure 5.0 bar. Maximum operating temperature 60°C
Range of wall mounted, concealed, thermostatic mixing vales with brass bodies and chrome plated trim sets, incorporating one or two quarter turn ceramic disc headworks with Single Lever operating members. Temperature is controlled independently via a thermostatic cartridge with various operating members (see model) which incorporates a manual override button. Both inlets incorporate an approved check valve cartridge, however, the complete product has not been fully tested to demonstrate it provides backflow protection. Maximum working pressure 6.0 bar. Maximum operating temperature 85°C.
Range of wall mounted, exposed, bar type thermostatic blending valves with brass bodies (chrome or matte black plated), incorporating quarter turn ceramic disc headwork controlling/diverting the flow. Temperature is controlled independently with a thermostatic cartridge with manual override button. Single lever type operating members. The inlets incorporate a stainless steel strainer and approved check valve cartridges however, the complete product has not been fully tested to demonstrate it provides backflow protection. Maximum working pressure 10.0 bar. Maximum operating temperature of 75°C.
Wall mounted thermostatic blending valves with brass bodies (various finishes), incorporating a quarter ceramic disc headwork controlling the flow with dome type operating member. Temperature is controlled via a thermostatic cartridge with dome type operating member incorporating a manual override button and a push button manual diverter to shower outlet. Both inlets incorporate a stainless-steel strainer and an approved check valve cartridge, however, the complete product has not been fully tested to demonstrate it provides backflow protection. Maximum working pressure 5.0 bar. Maximum operating temperature 65°C
Range of T-type thermostatic mixing valves (chrome plated DZR brass). The 521928 model incorporates stainless steel strainers in the inlets and approved check valve cartridges, verified by test (suitable for backflow protection against Fluid Category 2). Maximum working pressure: 10.0 Bar. Temperature: 90°C
Range of wall mounted, bar type thermostatic blending valves incorporating a quarter turn ceramic disc headwork or half turn ceramic diverter controlling the flow between outlets. The temperature is controlled by a thermostatic cartridge with various type of operating members incorporating a manual override button. Maximum working pressure 10 bar. Maximum operating temperature 60°C.
Range of wall mounted, exposed, thermostatic shower mixing valves (chromium plated brass). The products incorporate a ¼ turn ceramic disc or a 2-way ceramic disc diverter headwork (see model). Temperature is controlled independently via a thermostatic cartridge with a manual override button. The products have dome type operating members. Each inlet incorporates a combined EPDM washer and stainless steel strainer and an approved check valve cartridge, however, the complete product has not been fully tested to demonstrate it provides backflow protection. Maximum working pressure 6.0 bar. Maximum operating temperature 65°C.
Wall mounted thermostatic shower valve, (brass body - various finishes) incorporating a ceramic disc headwork controlling the flow to the shower outlet with a single lever operating member. The temperature is controlled independently via a thermostatic cartridge a with single lever operating member which incorporates a manual override. The inlets incorporate approved check valve cartridge; however, the complete product has not been fully tested to demonstrate it provides backflow protection. Maximum working pressure 10.0 Bar
Non-metallic materials and components comply with BS6920 at 60°C
Range of wall mounted thermostatic bar shower mixers, (chrome plated, brass bodies) incorporating either a quarter turn ceramic disc headworks or a ceramic disc diverter valve controlling the flow with cubed or dome type operating members. The temperature is controlled independently via a thermostatic cartridge using cubed or dome type operating members that incorporate a manual override button. The inlets incorporate stainless-steel strainers, EPDM washers and approved check valve cartridges, however, the complete product has not been fully tested to demonstrate it provides backflow protection. Maximum working pressure 8.0 Bar
Non-metallic materials and components comply with BS6920 at 65°C
Range of wall mounted, exposed thermostatic shower valves brass body with black finish. Flow is controlled and on twin outlet models, diverted between shower handset & overhead shower by the quarter turn ceramic cartridge headwork with dome operating member. Temperature is controlled independently via a thermostatic cartridge with manual override button and dome type operating member. Both inlets incorporate stainless steel strainers. The inlets of models 1.1836.465 & 1.1878.467 incorporate approved check valve cartridges however, the complete product has not been fully tested to demonstrate it provides backflow protection. Maximum working pressure 5 bar. Maximum operating temperature 50°C.
Range of wall mounted, bar type thermostatic shower mixer (chromium plated brass) Incorporating a quarter turn headwork controlling the flow with a dome type operating member. The temperature is controlled independently via a thermostatic cartridge with a dome type operating member incorporating a manual override button. Both inlets and shower outlet incorporate approved check valve cartridges, however, the complete product has not been fully tested to demonstrate it provides backflow protection. The inlets also incorporate stainless steel strainers. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C
Range of wafer or lugged butterfly valves with blue epoxy coated ductile iron bodies, stainless steel discs and EPDM seats. The valves can either be lever or gear operated via a handwheel. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Range of wafer and lug type butterfly valves incorporating blue epoxy coated ductile iron bodies, either stainless steel (SS316/SS304) or epoxy coated ductile iron discs and EPDM seat. The valves are either handwheel and gear operated (Models D371X and DL371X) or lever operated (Models D71X and DL71X). Maximum working pressure 16.0 bar Maximum operating temperature 85°C.
Range of wafer and lugged type butterfly valves with a blue epoxy coated ductile iron bodies, incorporating EPDM rubber seat, available with ductile iron (epoxy coated) or stainless-steel discs with a lever or gear operation. Maximum working pressure 16.0 Bar. Maximum operating temperature 80.0°C.
Range of butterfly valves incorporating blue epoxy coated ductile iron bodies and discs, EPDM ‘O’ rings, gaskets and seals. Maximum working pressure 16.0 bar. Maximum operating temperature 23°C.
Range of wafer and lugged butterfly valves with blue epoxy coated ductile iron bodies and stainless steel disc. DN50-DN300 are lever operated and DN350 – DN600 are handwheel operated. Maximum working pressure 16.0 bar.
Non-metallic materials and components comply with BS6920 at 85°C
Page 65 of 177
We use cookies to give you the best possible experience with WRAS. Some are essential to provide website functions and ensure the website is secure. We also use cookies to help us understand how people use the site and to make improvements. Click "Accept All" to enable recommended settings or click "Manage cookies" to adjust your settings. For more details, see our Cookie Policy.
