'Rubalit IS 95'. White coloured (opaque), ceramic disc component manufactured by powder pressing, sintering and grinding. For use with water up to 85°C.
'Endoprene 888.55'. Factory applied, two-component, beige coloured polyurethane coating. Mix and apply as per manufacturer's Data Sheet 'Doc. 089' dated '01/07/2011'. Cure for 8 days@20°C. For use with water up to 23°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Lak Series 2000 - Fusion Bonded Epoxy’. Factory applied, epoxy powder coatings available in the following colours: Code 25-1113: Description RAL5005 Blue Signal R.C. (dark blue coloured). Code 25-1117: Description RAL5015 Blue Sky R.C. (light blue coloured). Code 29-1116: Description RAL9005 Black Jet R.C. (black coloured). Apply as per manufacturer's technical information 'Rev.2,1 Q1 - 2021'. Cure for 10 minutes@180°C. For use with water up to 85°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
‘Series 2000 – Fusion Bonded Epoxy’. Factory applied, epoxy powder coatings available in the following colours: Code 29-0008: Description RAL9005 Black Deep FBE. Code 25-0084: Description RAL5015 Blue Sky. Code 25-1110: Description RAL5005 Blue Signal. Code 23-0004: Description Red Oxide Primer. Code 25-1160: Description SABSF29 NCS Blue Cornf. Apply as per manufacturer's technical information 'Rev.2,1 Q1 - 2021'. Cure for 10 minutes at 180°C. For use with water up to 85°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'DiChem Tiestop'. Site applied, grey coloured cementitious repair mortar. Mix 'DiChem Tiestop' and water in a mass ratio of 9.4:1 and apply as per manufacturer's instructions 'Rev 4, 02.22'. Cure for 21 days@7°C. For use with water up to 23°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
‘ECOCLEAR White Gray 9098’. Off-white/grey coloured, hot pressed GRP single layered panel. For use with water up to 55°C.
'Everbuild Plumber's P12 Silicone Grease (Barcode: 5055492703842)'. White coloured silicone grease. Apply as per manufacturer’s instructions. For use with water up to 65°C.
'Carbonfluortec 9720'. White coloured (opaque) lubricant. Apply as per manufacturer's instructions. For use with water up to 85°C.
'Flow Reducer Bp V2 ½ 34 9957, Flow reducer Bp V2 ½ short 34 9965 blue & Flow reducer Bp V2 3/8 short 34 9966 blue’. Blue coloured, injection moulded HDPE flow reducers. For use with water up to 23°C.
'Filter 99 3/8 349971 Dark Grey & Filter 99 ½ 349970 Light Grey'. Grey coloured, injection moulded HDPE filters. For use with water up to 23°C.
'Kingbull PE100 Blue Fitting (391740)'. Blue coloured, injection moulded polyethylene fitting. 'Kingbull PE100 Black Fitting (0103208)'. Black coloured, injection moulded polyethylene fitting. Both for use with water up to 65°C.
'70EP124p'. Black coloured, compression moulded EPDM 'O' ring. Shore hardness 70. Tested in-radius size 0.89mm. For use with water up to 85°C.
'EC-6509-A'. Black coloured, compression moulded EPDM rubber material. Shore hardness 65. Tested in-radius size 0.5mm. For use with water up to 80°C.
'Membrane R219 34 9513 NBR 55 Sh'. Black coloured, injection moulded NBR rubber membrane. Shore hardness 55. Tested in-radius size 1.0mm. For use with water up to 23°C.
'NB751359C'. Black coloured, compression moulded NBR rubber. Shore hardness 71. Tested in-radius size 1.0mm. For use with water up to 23°C. From December 2023, the material is suitable for use with water up to 85°C.
'CURA Liquid (Part No. 19261)'. Blue coloured, liquid PTFE anaerobic sealant. For use with water up to 85°C. This product is to be applied and cured in strict accordance with the manufacturer's instructions.
Range of single hole, single outlet (fixed) electronically controlled tap assemblies (chrome plated brass). Flow is controlled by a solenoid valve activated via an infra-red sensor. Models are either cold/premixed water only or hot and cold supply with a manually adjustable temperature lever. The product incorporates stainless steel strainers and the inlets incorporate approved check valve cartridges; however, the complete product has not been fully tested to demonstrate it provides backflow protection. The spout outlet incorporates a plastic aerator. Maximum working pressure 8.0 bar. Maximum operating temperature 70°C.
Range of single hole, single outlet (fixed) electronically controlled tap assemblies (chrome plated brass). Flow is controlled by a solenoid valve activated by via an infra-red sensor. The spout outlet incorporates a plastic aerator and the inlets incorporates stainless steel strainers. Models 351500 & 351510 incorporate an approved check valve cartridge; however, the complete product has not been fully tested to demonstrate it provides backflow protection. Models are either cold/premixed water only or hot and cold supply with a manually adjustable temperature lever. Maximum working pressure 8.0 bar. Maximum operating temperature 70°C.
‘Tubular’ range of wall mounted spout outlets (chromium plated brass). The flow is controlled by a solenoid valve activated via an infra-red sensor. The box assembly incorporates a solenoid valve, screwdriver operated spherical valve and the spout outlet incorporates a plastic aerator. Maximum working pressure 8.0 bar. Maximum operating temperature 65°C.
A range of deck mounted, single hole, single outlet (fixed) electronically controlled tap assemblies (chromium plated brass). The flow is controlled by a solenoid valve activated via an infra-red sensor. The temperature is controlled independently via a dome operating member. The spout outlet incorporates a plastic aerator. The inlets incorporate stainless steel strainers and single check valve cartridges (however, the complete assembly has not been fully tested to demonstrate that it provides adequate backflow protection). Maximum working pressure 5.0 Bar Maximum operating temperature 65 °C
A range of wall mounted, single hole, single outlet (fixed) electronically controlled tap assembly with chromium plated brass bodies. The flow is controlled by a solenoid valve activated via an infra-red sensor and a manually adjustable temperature lever. The inlet to the solenoid incorporates a stainless-steel strainer. The spout outlet incorporates a plastic aerator. Maximum working pressure 8.0 bar. Maximum operating temperature 70°C.
Range of single hole, single outlet (fixed) electronically controlled tap assemblies (chrome plated brass bodies). Flow is controlled by a solenoid valve activated by via an infra-red sensor. The inlet to the solenoid incorporates a stainless-steel strainer and check valve cartridge(s), verified by test (suitable for backflow protection against Fluid Category 2). The product incorporates a stainless steel braided PEX lined flexible connection hose, connecting the spout to the solenoid. The spout outlet incorporates a plastic aerator. Maximum working pressure - 10 Bar Maximum operating temperature - 60 °C
Bottom entry BS1212-4 (2016) compact type float operated valve for WC flushing cisterns. The inlet incorporates a flow restrictor. Maximum working pressure 10.0 bar. Cold water only
Side entry BS1212-4 (2016) compact type float operated valve for WC flushing cisterns. The inlet incorporates a flow restrictor. Maximum working pressure 10.0 bar. Cold water use only.
Range of bottom entry BS1212-4 (2016) compact type float operated valve for WC flushing cisterns. The inlet incorporates a plastic strainer. Maximum working pressure 10.0 Bar. Cold water use only.
Concealed WC dual flushing cistern with a bottom entry BS 1212-4(2016) float operated inlet valve providing a Type AG air gap arrangement and a dual flush outlet valve for full flush volumes of up to 6 litres and a reduced flush of up to 3 litres. The cistern is operated by a manual push button. Maximum working pressure - 10 Bar Maximum operating temperature – Cold water use only.
Concealed WC dual flushing cistern with a bottom entry BS 1212-4(2016) float operated inlet valve providing a Type AG air gap arrangement and a dual flush outlet valve for full flush volumes of up to 6 litres and a reduced flush of up to 3 litres. The cistern is operated by a manual push button. Maximum working pressure - 10 Bar Maximum operating temperature – Cold water use only.
WC flushing cistern incorporating a side entry BS1212-4 (2016) compact type float operated inlet valve providing a Type AG air gap with a dual flush drop valve for full flush volumes of up to 5.5 litres and a reduced flush of up to 2.7 litres and incorporates a servicing valve and flexible hose on the inlet supply. The cistern is operated by a manually operated push button. Maximum working pressure 10.0 bar. Cold water use only.
Wall hung WC pan with bidet function, the wash function is operated by push button or Bluetooth application. Flow is controlled by solenoid valve and discharged via AB air gap (suitable for backflow protection against fluid category 5). Maximum working pressure 10 Bar Maximum operating temperature 39°C
Range of single check valve assemblies with DZR brass bodies. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
'PCR-E' range of flow regulators with chrome plated brass housing and NBR sealing gaskets. Maximum operating temperature 65°C.
Range of thermostatic cartridges with plastic body and stainless steel strainer, for insertion into specifically dimensioned bores. Maximum operating temperature 85°C.
Range of single hole, single outlet (swivel) combination tap assemblies (chrome plated brass bodies), incorporating a ceramic cartridge headwork with a single lever operating member. The spout outlet are pull-out spray type, which incorporates aerators and approved single check valve cartridges, however the complete assemblies have not been tested to demonstrate backflow protection. Maximum working pressure 10.0 Bar Maximum operating temperature 65.°C
Range of single hole, single outlet (fixed) combination tap assemblies, (chrome plated, brass bodies), incorporating ceramic cartridge headworks and single lever operating members. The spout outlet incorporates a plastic aerator and the product is supplied with a lever operated pop-up waste.
Range of single hole, single outlet (fixed) pillar tap with brass bodies (chrome plated), incorporating ceramic disc headwork and single lever operating member. Spout outlet incorporates a plastic aerator. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C
Range of single hole, single outlet (fixed) combination tap assemblies (chromium plated brass), incorporating non-rising spindle headworks The spout outlets incorporates a stainless steel strainer and plastic flow strainer or a plastic aerator. The products are supplied with a click type waste. Maximum working pressure 10.0 Bar. Maximum operating temperature 65°C.
Range of single hole, single outlet (fixed) combination tap assemblies (chromium plated brass), incorporating non-rising spindle headworks with dome type operating members for models (101221) and a cross-top operating member for model (101229 Henlake basin mixer ). Model (101226 Lever basin mixer ) incorporates quarter turn ceramic disc headworks with single lever operating members. The spout outlets incorporates a stainless steel strainer and plastic flow strainer or a plastic aerator. The products are supplied with a click type waste. Maximum working pressure 10.0 Bar. Maximum operating temperature 65°C.
Range of single hole, single outlet (fixed) combination tap assemblies (chromium plated brass), incorporating a ceramic cartridge headwork with either a single lever or dome type operating member (see model). The spout outlet incorporates a plastic aerator (specific models only - see model section). Maximum working pressure 5.0 bar. Maximum operating temperature 60°C.
Range of single hole, single outlet (fixed) combination tap assemblies incorporating a brass body and ceramic cartridge headworks with single lever operating members. The spout outlet incorporates a plastic aerator. Maximum working pressure 5.0 bar. Maximum operating temperature 65°C.
Range of single hole, single outlet (fixed) combination tap assemblies (chromium plated brass), incorporating a ceramic cartridge headwork with a single lever operating member. The spout outlet incorporates a plastic aerator. The product is supplied with a click type waste. Maximum working pressure 5.0 bar.
Non-metallic materials and components comply with BS6920 at 60°C
Range of single hole, single outlet (fixed) pillar tap with brass bodies (chrome plated), incorporating ceramic disc headwork and single lever operating member. Spout outlet incorporates a plastic aerator. Maximum working pressure 5- 10.0 bar (see models). Maximum operating temperature 60°C – 85°C (see models).
Range of single hole, single outlet (swivel) combination tap assemblies, (chrome plated brass bodies). Model 922318 incorporates a ceramic cartridge headwork with single lever operating member. Model 922319 incorporates quarter turn ceramic disc headworks with single lever operating members. The spout outlets incorporate a flow straightener and is also supplied with an optional aerator. Maximum working pressure 6.0 bar. Maximum operating temperature 60°C
Single hole, single outlet (swivel) combination tap assembly (brass body - various finishes - see model), incorporating ¼ turn ceramic disc headworks with single lever operating members. The spout outlet can either incorporate a plastic aerator with an NBR washer or plastic flow straightener with a combined NBR washer and stainless steel strainer. Maximum working pressure 10.0 bar. Maximum operating temperature 65°C.
Range of single-hole, single outlet (swivel) combination tap assemblies (chrome and ‘supersteel’ plated brass), incorporating a ceramic cartridge headwork with a single lever operating member. The tap also incorporates a quarter turn ceramic disc headwork with a dome type operating member controlling the filtered water outlet. The spout outlet incorporates a plastic aerator. Maximum working pressure 10 Bar.
Non-metallic materials and components comply with BS6920 at 60°C
Single hole, metal, single outlet (swivel) combination tap assemblies (various finishes), incorporating a ceramic disc headwork controlling the temperature with a single lever operating member and a push on/off button cartridge controlling the flow. The spout outlet incorporates a plastic aerator. Supplied with a lever pop up waste. Maximum working pressure 10.0 bar.
Non-metallic materials and components comply with BS6920 at 70°C
Range of single hole, metal, single outlet (swivel) combination tap assemblies with brass bodies (various finishes), incorporating ceramic cartridge headwork with single lever operating member. Spout outlet incorporates a plastic aerator. Maximum working pressure 10.0 bar.
Non-metallic materials and components comply with BS6920 at 60°C
Floor mounted single hole, single outlet (swivel), combination tap assembly (chromium plated brass), incorporating a ceramic cartridge headwork with a single lever operating member and a manual diverter to shower outlet. The spout outlet incorporates a plastic flow straightener. This product is supplied with shower hose, shower handset and PEX inner-lined braided inlet hoses. Maximum working pressure 10.0 bar.
Non-metallic materials and components comply with BS6920 at 65°C
Wall mounted two-hole, single outlet, fixed, combination tap assembly (brass body, various finishes) incorporating a ceramic disk headwork with dome type operating member. The spout outlet incorporates a plastic aerator. Maximum working pressure 10.0 bar.
Non-metallic materials and components comply with BS6920 at 85°C
Range of two hole, single outlet (fixed) combination tap assemblies (chromium plated brass) incorporating quarter turn ceramic disc headworks with single lever operating members. The spout outlet incorporates a plastic flow straightener and a combined NBR washer and stainless steel strainer. The products are supplied with metal backnuts. Maximum working pressure 10.0 bar. Maximum operating temperature 65°C.
Range of wall mounted, two-hole, single outlet (fixed) combination tap assemblies (brass body, various finishes), incorporating a ceramic cartridge headwork with a single lever operating member. The spout outlet incorporates a plastic flow straightener. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.
Page 31 of 86
We use cookies to give you the best possible experience with WRAS. Some are essential to provide website functions and ensure the website is secure. We also use cookies to help us understand how people use the site and to make improvements. Click "Accept All" to enable recommended settings or click "Manage cookies" to adjust your settings. For more details, see our Cookie Policy.
