'Rotormagnet 12-0000294'. Dark grey coloured, injection moulded Polyamide + Strontium Ferrite magnet. For use with water up to 60°C.
'VESTAMID LX9042 NC'. White coloured, injection moulded PA12 material. For use with water up to 85°C.
'Fusamatic Electrofusion Fittings'. Black coloured, injection moulded, polyethylene Electrofusion Fittings (made in UK from Ineos Eltex TUB121 & Hostalen CRP 100 Resist CR Black). In December 2023, Electrofusion Fittings made in Anhui Province China from Borouge Borsafe HE3490-LS & Hostalen CRP 100 Resist CR black were added to the approval. For use with water up to 60°C.
'Fusamatic Electrofusion and Spigot Fittings'. Black coloured, injection moulded, polyethylene Electrofusion and Spigot Fittings (made from Ineos Eltex TUB121, Hostalen CRP 100 Resist CR Black & Borouge Borsafe HE3490-LS). For use with water up to 60°C.
'Fusamatic Electrofusion and Spigot Fittings'. Black coloured, injection moulded, polyethylene Electrofusion and Spigot Fittings (made from Ineos Eltex TUB121, Hostalen CRP 100 Resist CR Black & Borouge Borsafe HE3490-LS). For use with water up to 60°C.
'TP12939 Natural'. Natural (appears off-white) polyethylene material manufactured by extrusion compounding and then rotomoulding. For use with water up to 70°C.
'TP12978 Black'. Black coloured, polyethylene material manufactured by extrusion compounding and then rotomoulding. For use with water up to 70°C.
'212N' components. Black coloured, injection moulded EPDM rubber components with a shore hardness of 70. ‘O’ rings (in-radius 1.31mm), washers (in-radius 1.05mm) & membranes (in-radius 1.75mm) made in Italy. ‘O’ rings (in-radius 1.31mm) & washers (in-radius 1.05mm) made in China. For use with water up to 85°C. When processing an application for a Product Approval incorporating these components, these are the only shapes covered by the approval.
'EPDM-812-cm (70H/mid)'. Black coloured, compression moulded EPDM sheet material. Shore hardness 70A. Tested in-radius size 1.0mm. For use with water up to 23°C.
'TamAcryl 2000 Orange or Blue with corrosion inhibitor', orange coloured or blue coloured (once mixed), site applied acrylic grouts. Mix Part A (orange or blue) with 2% accelerator and then mix with Part B (colourless) in a 1:1 volume ratio. Apply as per manufacturer’s TDS 'V1UK20 – 2020.10.22'. Cure for 12 hours at 16°C. For use with water up to 23°C. This material is only approved for the mixing & curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval. These materials are for use in concrete reservoirs and similar structures, constructed in accordance with the design criteria of BS EN 1992-3:2006 (Design of concrete structures – Liquid retraining and containing structures) with respect to normal frequency of joints. The material has been tested at a reduced surface area to volume ratio of 1000mm² per litre.
Range of wall mounted, single-hole, single outlet (fixed) electronically controlled combination tap assemblies (chrome plated brass or stainless-steel bodies) which are supplied with pre-mixed water. Flow is controlled via an infra-red activated solenoid valve and the spout outlets incorporate plastic aerators. Maximum working pressure 8.0 bar
Non-metallic materials and components comply with BS6920 at 65°C
Range of wall mounted, electronically controlled combination tap assemblies, (chrome plated brass or stainless steel bodies). The flow is controlled by a solenoid valve that is activated via an infra-red sensor The spout outlet incorporates a plastic aerator. The product incorporates a stainless steel braided PEX lined flexible connection hose assembly, connecting the spout to the solenoid valve. Maximum working pressure 8.0 Bar
Non-metallic materials and components comply with BS6920 at 65°C
Side entry BS1212-4 fill valves with plastic bodies. Maximum working pressure 10.0 bar. Coldwater use only.
Range of bottom entry BS1212-4 telescopic fill valves with plastic bodies. Maximum working pressure 10.0 bar. Cold water use only.
Range of tundishes incorporating a plastic or coated, mild steel body. Maximum operating temperature 85°C.
Range of aerator kits incorporating plastic flow regulators (1.9l/min, 3.5l/min & 5.0l/min) with plastic bodies and EPDM ‘O’ rings. Plastic adaptors, NBR washers and chromium plated brass housings may also be supplied as part of the kit. Maximum operating temperature 65°C.
Range of ceramic cartridge headworks with plastic bodies & silicone rubber seals. For insertion into specifically dimensioned bores. Maximum working pressure 16.0 Bar.
Non-metallic materials and components comply with BS6920 at 80°C
Thermostatic cartridges with plastic or brass bodies, and EPDM ‘O’ rings and stainless steel strainers. For insertion into specifically dimensioned bores. Maximum working pressure 10.0 bar. BS6920 85°C.
‘VT30’ range of thermostatic cartridges with a plastic body and EPDM ‘O’-rings and stainless steel strainers. For insertion into specifically dimensioned bores. Maximum working pressure 16.0 bar. BS6920 70°C.
Range of wall mounted, single hole, single outlet (fixed) combination tap assemblies (brass bodies - various finishes), incorporating ceramic cartridge headworks with single lever operating members. The spout outlets incorporate plastic aerators. Maximum working pressure 10 bar. Maximum operating temperature 65°C
Single hole, single outlet (fixed) combination tap assembly (chromium plated brass) incorporating a sequential headwork controlling both flow and temperature with single lever type operating member. The spout outlet incorporates a plastic flow straightener. Maximum working pressure 5.0 Bar. Maximum operating temperature 85°C.
Wall mounted single hole, single outlet (fixed) combination tap assembly, brass body(various finishes), incorporating a detent headwork that controls both flow and temperature with a single lever operating member. The spout outlet incorporates a plastic aerator. The product also incorporates a permanently open waste outlet. Maximum working pressure 10.0 bar
Non-metallic materials and components comply with BS6920 at 60°C
Range of single hole, single outlet, swivel combination tap assemblies (brass bodies, various finishes - see model), incorporating a ceramic cartridge headwork with a single lever operating member. The vented models are supplied with a stainless steel braided PEX lined flexible hose assembly incorporating a ½" captive nut end connection, which provides main cold water to a venturi device which is part of a command centre (not supplied). The Arc vented models are supplied with a DZR brass tee piece, two DZR brass adaptors, two stainless-steel strainers (each combined with an EPDM washer) and a plastic flow restrictor, for installation prior to the cold inlet hose. The Arc and Cube mains models are supplied with two DZR brass adaptors and two stainless-steel strainers (each combined with an EPDM washer), for installation on each inlet hose. The spout outlet incorporates a plastic aerator. Maximum working pressure 5.0 bar.
Non-metallic materials and components comply with BS6920 at 65°C
Range of two hole, single outlet (fixed), combination tap assemblies with (brass bodies - various finishes) incorporating quarter turn ceramic disc headworks with single lever or dome type operating members (see models). The spout outlet of model F4195** incorporates a plastic aerator. The products are supplied with metal back nuts. Maximum working pressure 10.0 bar.
Non-metallic materials and components comply with BS6920 at 65°C
Range of two-hole, single outlet (fixed) combination tap assemblies (brass bodies - various finishes), incorporating quarter turn ceramic disc headworks with cross top operating members and a manual diverter to shower outlet. The products are supplied with metal back nuts. Maximum working pressure 10.0 Bar
Non-metallic materials and components comply with BS6920 at 65°C
Range of two-hole, single outlet (fixed) combination tap assemblies, (brass bodies - various finishes), incorporating quarter turn ceramic disc headworks with single lever type operating members and a manual diverter to shower outlet. The products are supplied with metal back nuts. Maximum working pressure 10.0 Bar
Non-metallic materials and components comply with BS6920 at 65°C
Range of two-hole, single outlet (fixed) combination tap assemblies with (brass bodies - various finishes) incorporating quarter turn ceramic disc headworks with single lever operating members and a manual diverter to shower outlet. The products incorporate waterfall type spout outlets with stainless steel strainers. Maximum working pressure 10.0 Bar
Non-metallic materials and components comply with BS6920 at 65°C
Deck mounted, two-hole, single outlet (fixed) combination tap assemblies, (chrome plated brass bodies) incorporating quarter turn ceramic disc headworks with single lever operating members and lockable diverter to shower outlet. The spout outlet incorporates a plastic aerator. Product is supplied with shower hose, shower handset and metal backnut. Maximum working pressure 10.0 bar.
Non-metallic materials and components comply with BS6920 at 60°C
Range of three-hole, single outlet (fixed) combination tap assemblies (brass bodies with various finishes) incorporating quarter turn ceramic disc headwork with single lever operating members. Spouts incorporate plastic aerators. The products are supplied with stainless steel PEX lined flexible connecting hoses incorporating BSP female end connections. Some models supplied with a lever operated pop-up waste (20713831-00, 20713831-69, 20713832-00 & 20713832-69) and all models are supplied with metal backnuts. . Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.
Range of bath fillers, waste and overflow assemblies (chromium plated brass and plastic body), incorporating a click type pop-up waste. The inlet of model 58 129 003 Hansgrohe Exafill incorporates an approved check valve cartridge however, the complete product has not been fully tested to demonstrate it provides backflow protection. Maximum working pressure 10.0 bar.
Non-metallic materials and components comply with BS6920 at 65°C
Range of concealed wall mounted valve assemblies (brass bodies – various finishes) incorporating a quarter turn ceramic disc headwork with a dome type operating member. Maximum working pressure 10 bar. Maximum operating temperature 60°C
A range of wall mounted spout outlets with chromium plated brass or stainless steel bodies, incorporating plastic aerators or flow straighteners at the outlet. Open outlet use only.
Expansion vessel with stainless steel body and butyl membrane. Maximum working pressure 10.0 bar. Maximum operating temperature 90°C
Range of water filter cartridges with plastic bodies. Maximum working pressure 8.6 bar. Cold water use only.
Range of activated carbon filter cartridges and heads, with plastic bodies. Maximum operating pressure 8.6 bar. Cold water use only.
‘Atlas’ range of green fusion welded polypropylene fittings for use with ‘Atlas’ PPRGF or PPR pipes. Maximum working pressure 20.0 bar. Cold water use only.
‘F18’ range of brass press fittings (TH and U crimp profiles) with EPDM ‘O’-rings for use with Rifeng B1 PEX/AL/PEX multilayer pipe. Maximum working pressure 10.0 bar. Maximum operating temperature 95°C.
Range of brass press fittings (TH and U crimp profiles) with EPDM ‘O’-rings for use with RIIFO B1 PEX/AL/PEX multilayer pipe. Maximum working pressure 10.0 bar. Maximum operating temperature 95°C.
U Profile range of press fittings incorporating EPDM ‘O’-rings. For use with Mingshi (S-1-0509/10/11/12/17/13) PEX-AL-PEX pipe. Maximum working pressure 10.0 bar. Maximum operating temperature 95°C
Range of ‘Henco Profit Synthetic’ pushfit fittings with PPS (HPK models) or brass (HP models) bodies and EPDM o-rings, to be used with ‘Henco RIXc’ PEXc/Al/PEXc multilayer pipes. Maximum working pressure 10.0 bar. Maximum operating temperature 95°C.
Fluxo range of Brass & PPSU crimp fittings for use with ‘Fluxo’ PEX/Al/PEX Multilayer Pipe. Crimp joint is achieved by a TH profile crimp jaws. Maximum working pressure 10bar @ 70°C, 6Bar @ 95°C.
Range of brass (Series 1000 & 1100) and DZR brass (Series 1100CZ) compression fittings, various finishes. For use with copper tube EN1057. Maximum working pressure 30.0 bar. Maximum operating temperature 100°C.
Range of copper and brass press-fit fittings with HNBR o-rings, for use with copper tube manufactured to EN1057. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Supreme S16 range of fittings for use with PE pipes (manufactured to EN12201-2). Supplied with a plastic pipe support liner For above and below ground use. Maximum working pressure 16.0 bar. Cold water use only.
Range of Effast PVC-u solvent welded and/or threaded fittings for use with PVC-u pipe manufactured to (EN1452-2). Maximum working pressure 16.0 bar. Cold water use only.
Stainless steel press fittings incorporating EPDM ‘O’-rings for above ground use only. To be used with stainless steel 316L pipe (EN 10312). Maximum working pressure 10.0 bar. Maximum operating temperature 85°C.
Range of syphonic flush valves with plastic bodies. Cold water only
Range of plate heat exchangers with stainless steel plate bodies and copper brazing. Maximum working pressure: 45 Bar. Maximum operating temperature: 99 °C.
Pentobox range of water meter manifolds with plastic bodies and an integral spherical valve on the inlet. The models incorporate a non-return valve, (not suitable for backflow protection). Compression models are for use with metric and imperial PE80 pipe (manufactured to BS EN 12201). Maximum working pressure 16.0 bar. Cold water use only.
Range of water meter manifolds with brass or DZR brass bodies. The outlets incorporate non-return valves (not suitable for backflow protection). For use with copper pipe manufactured to BS EN 1057 (WBBADAPT112). Maximum working pressure 10.0 bar. Cold water use only.
Page 20 of 50
We use cookies to give you the best possible experience with WRAS. Some are essential to provide website functions and ensure the website is secure. We also use cookies to help us understand how people use the site and to make improvements. Click "Accept All" to enable recommended settings or click "Manage cookies" to adjust your settings. For more details, see our Cookie Policy.
