Thermostatic circulation valves incorporating DZR brass bodies and EPDM ‘O’-rings. Maximum working pressure 25.0 bar. Maximum operating temperature 90°C.
‘ProtectoSAN’ range of electrolytic scale inhibitors with chromium plated copper bodies and brass end connectors. Maximum working pressure 20.0 bar. Cold water use only.
Range of UV disinfection units with stainless steel bodies. Maximum working pressure 10.3 bar. Maximum operating temperature 60°C.
Drinking water fountain, incorporating of spherical valve, self-closing tap and pressure reducing valve enclosed within a metal housing. Maximum working pressure 25.0 bar. For cold water use only.
‘Ultraform® N2320 Aqua AT uncoloured’. Uncoloured (appears white), injection moulded C-POM material. For use with water up to 65°C.
'BPL High Build QD Bitu Black'. Factory applied, black coloured bituminous coating. Apply as per manufacturer’s data sheet ‘427-rev03’ dated 'Feb' 2024'. Cure: flash off for 15 minutes at ambient temperature of 30°C, followed by stoving at 55°C for 10 minutes and then 7 days maturation at ambient temperature of 30°C. For use with water up to 23°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
‘BFSC Foug SDN’. Factory applied, grey coloured, blast furnace slag cement intended to line pipes. Mix sand and cement in a mass ratio of 1.5:1, then add water in a water/cement mass ratio of 0.36:1 and apply as manufacturer's instructions. Cure for 48 hours@23°C, 70% relative humidity. For use with water up to 23°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'ARC SD4i(E)'. Factory applied, grey and blue coloured, two-part epoxy coatings. Mix parts A and B in a weight ratio of 2.5:1 and apply as per manufacturer's Application Instructions 'EN-085034EU', dated '01/2025'. Cure for 72 hours@20°C (±2°C). For use with water up to 55°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the materials are not covered by the scope of the approval.
'ARC 858(E)'. Factory applied, dark grey coloured, two-part epoxy coating. Mix parts A and B in a weight ratio of 4:1 and apply as per manufacturer's Application Instructions 'EN-085013EU', dated '08/2024'. Cure for 54 hours@20°C (±2°C). For use with water up to 55°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the materials are not covered by the scope of the approval.
'ENDOPRENE® 851 Blanc'. Factory applied, white coloured, two-component polyurethane coating. Mix parts A & B in 50:50 volume ratio and apply as per manufacturer's TDS dated 10/07/2024. Cure for 6 days@40°C. For use with water up to 60°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the materials are not covered by the scope of the approval.
'175-767 Polyester blue 5012'. Factory applied, blue coloured polyester coating. Apply as per manufacturer's instructions updated '15.03.2018'. Cure for 10 minutes@180°C. For use with water up to 55°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Novus N34 & SF3300'. NBR/fibre gaskets which are white coloured on one side and dark cream coloured on the other, maufactured by calendaring. For use with water up to 23°C. For use only as a jointing/gasket material having been tested at reduced surface area to volume ratio.
'Novus 20'. Yellow coloured, nitrile rubber/aramid jointing material manufactured by calendaring. For use with water up to 23°C. For use only as a jointing/gasket material having been tested at a reduced surface area to volume ratio.
'TIY 001'. Grey coloured (opaque), compression moulded GRP panel. For use with water up to 23°C.
'SJ-195120WT GRP Panel'. Off-white coloured, compression moulded GRP panel. For use with water up to 50°C.
'Klüberbeta VR 67-3500'. Cream coloured silicone grease intended for use as a lubricant. For use with water up to 85°C.
'Unisilkon TK 002/500'. Colourless lubricating oil. Apply as per manufacturer's data sheet. For use with water up to 60°C.
'Syntheso LM 220'. White coloured (opaque) lubricant grease. Apply as per manufacturer's instructions. For use with water up to 85°C.
'UNISILKON L 250 L'. White coloured (opaque) lubricant grease. Apply as per manufacturer's instructions. For use with water up to 85°C.
'Relon A500 Nero 4095 GF30 K'. Black coloured, injection moulded, glass filled PA66 material. For use with water up to 80°C.
'GPS Excel Black PE100 Pipe'. Black coloured, extruded PE100 pipe. For use with water up to 23°C.
'Hydrothen PE 100 Black Pipe'. Black coloured, extruded polyethylene pipe. For use with water up to 85°C.
'WIN Spigot Fittings'. Black coloured, injection moulded PE100 spigot fittings. For use with water up to 60°C.
'GPS EXCEL NB Pipe'. Dual layered, extruded pipe consisting of a black coloured, PE100 inner layer and blue coloured, PE100 outer layer. For use with water up to 23°C.
'+GF+ HDPE PE 100' (black and black with blue stripes)'. Extruded polyethylene pipes. For use with water up to 60°C.
'8108658 V0010_K LLDPE'. Blue coloured, roto-moulded LLDPE material. For use with water up to 23°C.
'8108658 V0010_V LLDPE'. Blue coloured, roto-moulded LLDPE material. For use with water up to 23°C.
'BC245MO' & 'Bn BC245MO-90'. Natural (off-white), injection moulded polypropylene material. For use with water up to 85°C.
'BE50' & 'Bn BE50-100'. Natural (off-white), injection moulded polypropylene material. For use with water up to 85°C.
'1024 Titan Bladder'. Clear (translucent), extruded TPU bladder. Shore hardness 87. Tested in-radius size 0.48mm. For use with water up to 80°C.
'Pimtaş Plastik PVC-U Pipe'. Grey coloured, extruded PVC-U pipe. For use with water up to 50°C.
'+GF+ uPVC Pressure pipe'. Grey coloured, extruded uPVC pipe. For use with water up to 50°C.
'E 71 65 003'. Black coloured, injection moulded EPDM 'O' rings. Shore hardness 70. Tested in-radius size between 0.5mm & 3.5mm. For use with water up to 85°C.
'TRA-7073'. Black coloured, compression moulded EPDM material. Shore hardness 70. Tested in-radius size 1.0mm. For use with water up to 85°C.
'EPDM70(E7-512K)'. Black coloured, compression moulded EPDM material. Shore hardness 70. Tested in-radius size 1.0mm. For use with water up to 65°C.
'FDJ-75'. Black coloured, injection moulded FKM rubber material. Shore hardness 76. Tested in-radius size 1.03mm. For use with water up to 85°C.
'NE7130 Grey 60'. Light grey coloured, injection moulded silicone rubber material. Shore hardness 60. Tested in-radius size 1.97mm. For use with water up to 85°C.
'Loctite 403'. Clear, liquid cyanoacrylate adhesive. Apply as per manufacturer's technical data sheet reference ‘2.6’, dated August 2012. Cure for 72 hours@22°C. For use with water up to 23°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
‘JET Pipe Sealing Cord’. White coloured nylon cord coated with a silicone paste, intended for use as a thread sealant. The cord is to be applied and tightened in accordance with Data Sheet ‘P02415', updated 11/07/24 and this material is only approved for these conditions. For use with water up to 85°C.
'Datkafix DF-43'. Blue coloured pipe sealant. Apply as per manufacturer's TDS '01/02/2024 v1.1'. Cure for 24 hours@23°C. For use with water up to 85°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'TruTite™ 313 Thread Lock'. Blue coloured pipe sealant. Apply as per manufacturer's TDS version '1.0 26/07/24'. Cure for 24 hours@23°C. For use with water up to 85°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'CORE®'. Blue coloured pipe sealant. Apply as per manufacturer's instructions version '1', issue date '26/07/24'. Cure for 24 hours@23°C. For use with water up to 85°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
Range of wall mounted, two hole, single outlet (fixed) mains electric or battery controlled tap assemblies (chromium plated brass) incorporating approved check valve cartridges however, the complete product has not been fully tested to demonstrate it provides backflow protection . The flow is controlled via a solenoid valve activated via an infra-red sensor. The inlet to the solenoid incorporates a stainless-steel strainer. The tap is supplied with spherical valves for both hot and cold inlets. The spout outlet incorporates a plastic aerator. Maximum working pressure 5.0 bar. Maximum operating temperature 65°C.
Range of deck mounted, Infra-red electronic basin mixers with mixing device and adjustable temperature limiter. The tap incorporates EPDM O-rings. The spout outlet incorporates a plastic aerator. Maximum working pressure 10 bar. Maximum operating temperature 60°C
Range of wall mounted, single-hole, single outlet, electronically controlled combination tap assemblies, (chrome plated brass or stainless steel bodies). The flow is controlled by a solenoid valve activated via an infra-red sensor. The spout outlet incorporates a plastic aerator. The products incorporate a stainless steel braided PEX lined flexible hose assembly, connecting the spout to the solenoid valve. Maximum working pressure 8.0 Bar.
Non-metallic materials and components comply with BS6920 at 65°C
Range of deck mounted, electronically operated combination tap assemblies (chromium plated brass). The flow is controlled by a solenoid valve which is actuated via an infrared sensor on the spout. The spout outlet incorporates a plastic aerator. Maximum working pressure 8.0 bar. Maximum operating temperature 60°C.
Range of single hole, single outlet (fixed) electronically controlled tap assemblies (chromium plated brass). Flow is controlled by a solenoid valve activated via an infra-red sensor. The spout outlet incorporates a plastic aerator. The main body incorporates a stainless-steel strainer prior to the solenoid. Maximum working pressure 8.0 Bar.
Non-metallic materials and components comply with BS6920 at 65°C
Range of wall mounted, single-hole, single outlet (fixed) electronically controlled combination tap assemblies (chrome plated brass bodies). Flow is controlled via a solenoid, activated via an infra-red sensor. The outlets incorporate plastic aerators. Maximum working pressure 8.0 bar Maximum operating temperature 70°C
Non-metallic materials and components comply with BS6920 at 70°C
BS1212-4 (2016) compact type float operated valve for WC flushing cisterns, side entry type. The inlet incorporates a plastic flow restrictor. Maximum working pressure 10.0 bar. Cold water use only.
Range of side and bottom entry BS1212-3 inlet valves, with plastic bodies and brass shanks. Maximum working pressure: 3.0 Bar low pressure and 14.0 bar high pressure Maximum operating temperature: Cold water use only.
Page 184 of 222
We use cookies to give you the best possible experience with WRAS. Some are essential to provide website functions and ensure the website is secure. We also use cookies to help us understand how people use the site and to make improvements. Click "Accept All" to enable recommended settings or click "Manage cookies" to adjust your settings. For more details, see our Cookie Policy.
