Broen-Lab A/S Approvals


WRAS Approval Number: 1612803

Uniflex range of stainless steel braided PEX lined flexible hose assemblies with EPDM `O` rings and/or fibre washers available with various end connectors. Maximum working pressure 10.0 bar. Maximum working temperature 70ºC

  • Section: 1863 Tubes
  • Section Subtitle: Elastomeric.
  • WRAS Approval Number: 1612803
  • Expiry date: 31/12/2021
  • Size: DN8 Hose, with Various connectors BSP (M) – 3/8” (Code 32) , ½” (Code 31) , 3/4” (Code 33) Captive Nut - 3/8” (Code 41) , ½” (Code 40) , 3/4” (Code 42) Brass Pipe Connector 10mm (Code10), 12mm (Code 12) , 15mm (Code 15) Uniflex Connector M16 – Straight (Code 20) , 45º (Code 25), 90º (Code 30) M10 Connectors – Short (Code 51) , Long (Code 52)
  • Marking: Neoperl, WRAS and date of manufacture (MM/YYYY) on crimped connector.
  • Installation Requirements R001 R008
  • Model
    Uniflex range 93 V XX(inlet) XX(outlet) XXXX(length)
  • Factor: Broen-Lab A/S
    Company Name
    Broen-Lab A/S
    Address
    Drejervaengtetr 2 5610 Assens Denmark
    View All Listings by this Company
  • Manufacturer: Neoperl Nordic A/S
    Company Name
    Neoperl Nordic A/S
    Address
    View All Listings by this Company

Print This Approval


WRAS Approval Number: 1612804

Range of wall and deck mounted, fixed or swivel laboratory taps and mixers (powder coated brass) incorporating ceramic disc headworks, non-rising spindle headworks or ceramic cartridge headworks, with lever or dome operating members. The spout outlets incorporate an aerator, a hose union connection, or a DC pipe interrupter with hose union connection. Maximum working pressure 10.0 bar. Maximum operating temperature 70°C

  • Section: 1795 Taps
  • Section Subtitle: Laboratory.
  • WRAS Approval Number: 1612804
  • Expiry date: 31/12/2021
  • Note: (i) IRN 040 applies to the wall mounted taps, and when the hose union connection is installed. (ii) IRN 090 applies to taps with hose union connection only. (iii) Where the DC pipe interrupter is used, it must be installed so that the lowest point of the air aperture is not less than 150mm above the spillover level of the receiving receptacle, and have no valve, flow restrictor or tap on its outlet. IRN R040 does not apply.
  • Size: Broen braided hoses DN10 or Broen Compression Fittings 8mm-15mm for copper and stainless steel
  • Marking: Broen on operating member
  • Installation Requirements R001 R006 R010 R040 R090
  • Model
    2534 XXX 82 XX - XX X 2536 XXX 82 XX - XX X 2510 XXX 82 XX - XX X 2511 XXX 82 XX - XX X 2533 XXX 82 XX - XX X Models added May 2017: 6034 XXX 82 XX – XX X 6036 XXX 82 XX – XX X 6033 XXX 82 XX – XX X 6010 XXX 82 XX – XX X 6011 XXX 82 XX – XX X
  • Manufacturer: Broen-Lab A/S
    Company Name
    Broen-Lab A/S
    Address
    Drejervaengtetr 2 5610 Assens Denmark
    View All Listings by this Company

Print This Approval


WRAS Approval Number: 1812355

DC type pipe interrupters with a permanent atmospheric vent and DZR brass body, NBR ‘O’ ring and gaskets. Maximum working pressure 10.0 bar. Cold water use only.

  • Section: 0014 Backflow Prevention Devices
  • Section Subtitle: SCHEDULE 2 - Section 6.2. Type DC - Pipe interrupter with permanent atmosphere vent. The device must be fitted with the lowest point of the air aperture not less than 150mm above the free discharge point, or spillover level of an appliance, and have no valve, flow restrictor or tap on its outlet.
  • WRAS Approval Number: 1812355
  • Expiry date: 31/12/2023
  • Size: See model
  • Marking: Broen-lab, & CR on body
  • Installation Requirements R001 R165
  • Model
    15279709 – M19x1/2” BSP M 15279719 – ½” x ½” BSP M 15279729 – 3/8” x ½” BSP M 15279739 – M19 x 3/8” BSP F 15279749 - ½” x ½” BSP F 15279759 - 3/8” x 3/8” BSP F
  • Manufacturer: Broen-Lab A/S
    Company Name
    Broen-Lab A/S
    Address
    Drejervaengtetr 2 5610 Assens Denmark
    View All Listings by this Company

Print This Approval


Show Per Page
5102050Show All

Back To Directory Sections

Page of 1