Range of in-line, manually adjustable pressure reducing valves with brushed chrome plated DZR brass bodies, for use with copper pipe (manufactured to BS EN 1057). Supplied with a pressure gauge. Maximum inlet supply pressure 16.0 bar. Maximum outlet pressures between 1.0 and 6.0 bar. Maximum operating temperature 85°C.
Pre-set pressure relief valves, pre-set at 3.0 bar, with a plastic body. Maximum operating temperature 85 °C.
Range of solenoid valves with plastic bodies. The inlets incorporate a plastic flow regulator and optional strainer. Maximum working pressure 10.0 bar. Models which end with ‘H’ have a maximum operating temperature of 85°C. All other models are cold water use only.
Range of lever operated spherical valves with a DZR brass body, incorporating a stainless-steel ball. The press fit connections are to be used with copper pipe to BS EN1057 and the crimp joint is achieved by a M and V profile crimp jaws. Maximum working pressure 25.0 bar. Maximum operating temperature 100°C.
Range of in-line spherical valves (brushed chrome DZR brass body) with lever or butterfly type operating members (see models), DZR brass ball (chromium plated brass) and PTFE seats and washers. Maximum working pressure 10.0 bar. Maximum operating temperature 100°C.
Range of screwdriver operated spherical valves with a brass body and either a chrome plated brass ball (4000120555 model) or brass ball (all other models). Maximum working pressure 10.0 bar. Maximum operating temperature 100°C.
Range of lever operated spherical valves with brass bodies, ball and PTFE seats and incorporates two single check valve assemblies (verified by test, suitable for backflow protection against Fluid Category 3). Compression models are for use with BSEN 1057 copper pipe. Maximum working pressure 10 Bar Maximum operating temperature 85°C
Range of in-line angled or ‘T’ type spherical valves with chromium plated brass, nickel plated brass, brass or DZR brass bodies and brass ball. Models have screwdriver, lever or butterfly operating members. Maximum working pressure 10.0, 16.0 or 25.0 Bar. Maximum operating temperature 85° or 99°C.
Range of in-line angled or ‘T’ type spherical valves with chromium plated brass and brass ball. Models have screwdriver, lever or butterfly operating members. Maximum working pressure 10.0, 16.0 or 25.0 Bar. Maximum operating temperature 85° or 99°C.
Range of straight, angled, tee and Y shaped isolation valves incorporating brass bodies, NBR ‘O’-rings or PTFE seats depending on model variant. Maximum working pressure 10.0 bar. Maximum operating temperature 85°C.
‘Floreg’ range of in-line lever operated spherical valve with a DZR brass body (brushed chromium plated) and ball. The product incorporates a stainless-steel mesh strainer and a flow regulator. Compression connection to be used with copper pipe to BS EN 1057. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Range of lever operated spherical valves with a brushed chrome plated brass body, brass ball and PTFE seals. . Maximum working pressure 40.0 bar. Maximum operating temperature 85°C.
Range of lever or screwdriver operated in-line spherical valves (chrome plated brass body), brass ball and EPDM seals. Compression connection to be used with copper pipe EN1057. Maximum working pressure 10.0 bar. Maximum operating temperature 85°C.
Range of spherical ball valves having brass, DZR brass or stainless-steel bodies and lever type operating members. For use with stainless steel pipe (EN10312) or copper pipe (EN1057). Maximum working pressure 25.0 Bar. Maximum operating temperature 85.0°C.
Range of spherical valves with brushed chrome plated brass bodies, chrome plated brass ball, PTFE seats and butterfly or lever operating member. Maximum operating pressure 40.0 bar. Maximum operating temperature 95°C
Range of spherical valves, with brass bodies (either nickel plated or chromium plated) and a chromium plated brass ball. The products can be supplied with various operating members (see model). The products are to be used with copper pipe (manufactured to EN1057). Maximum working pressure 25.0 bar. Maximum operating temperature 85°C.
Range of spherical valves incorporating (brass bodies - various finishes). Maximum working pressure 16.0 bar, 25.0 bar for model 10.61092.015.CP5R-8510 & 10.61092.015.CP12-8510. Maximum operating temperature 85°C.
Range of spherical valves, with DZR brass bodies and brass ball (15mm size) or stainless steel ball (all other sizes). The products can be supplied with various operating members (see model). Jointing is achieved via a crimping tool, the 15-28mm sizes use a ‘M’ profile and the 35-54mm sizes use a ‘V’ profile. The press-fit connection is to be used with copper pipe (manufactured to EN 1057), stainless steel pipes (manufactured to EN10312) or carbon steel pipe (manufactured to EN10305-3). Maximum working pressure 25.0 bar. Maximum operating temperature 85°C.
Range of spherical valves with various operating members, brass bodies, brass balls, EPDM ‘O’-rings and PTFE seats. Maximum working pressure 40.0 bar. Maximum operating temperature 85°C.
Range of angled and straight ball valves with plastic valve bodies, PTFE seats and EPDM O-rings. Maximum working pressure 16 bar. Maximum operating temperature 40°C
Range of resilient seated gate valves with cast iron bodies (blue epoxy coated), EPDM coated cast iron wedges and a handwheel operating member. Maximum working pressure 16.0 bar.
Non-metallic materials and components comply with BS6920 at 85°C
Screw down stop valve, with a brass body and handwheel operating member. Maximum working pressure 10 bar. Maximum operating temperature 23°C
Range of screw down drain valves with brass bodies, for use with copper tube to BSEN1057. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Range rising spindle screw down stop valves with gunmetal bodies and T-type operating members. Models SCM020000535, SCM025000536, SCI100000533, SCM025002164 & SCM032002165 models are to be used with PE80 pipe manufactured to EN 12201. Maximum working pressure: 12.5 Bar. Maximum operating temperature: 23°C.
Range of electrolytic scale inhibitors incorporating copper bodies. For use with copper pipe complying with BS EN 1057. Maximum working pressure 10.0 bar. Maximum operating temperature 40°C.
Water chiller and heater units for under counter installation incorporating an approved double check valve at the inlet, to be used in conjunction with an outlet tap arrangement or flow control device, with a range of taps that are supplied with the chillers. Maximum working pressure 10.0 Bar Maximum operating temperature 98.0°C
'Sigrafine® EK2239, EK2200, EK2230 & EK2240'. Grey coloured, compression moulded, phenolic resin impregnated carbon rings. For use with water up to 85°C.
'4.R50760000-01'. Beige coloured, sintered, ceramic rotor shaft. For use with water up to 85°C.
'NF 131118'. Factory applied, grey coloured, two-part, water-based epoxy coating. Mix resin and curing agent in a 9:1 weight ratio and apply as per manufacturer's TDS 'PAMCN-V1', dated '20240423'. Cure for 60 minutes@50°C. For use with water up to 23°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'ENDOPRENE® 864'. Factory applied, cream coloured, two-part Polyurethane coating. Mix parts A and B in a 66:34 volume ratio and apply as per manufacturer's TDS dated '26/11/2024'. Cure for 50 hours@20°C. For use with water up to 60°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Electrocement CEM III/B-SR - Ramco Slag'. Factory applied, grey coloured Portland Slag Cement. Mix cement:sand:water in a 0.6:1.0:0.22 weight ratio and apply as per manufacturer's work instructions 'WP-08-05 I, issue no. 04, Rev. 0', dated '22.08.2024'. Cure for 24 hours at 27°C. For use with water up to 85°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'GM2025'. Factory applied, grey coloured Portland Cement Mortar. Mix cement, sand and water in a 2:1:0.4 mass ratio and apply as per manufacturer's instructions issue 'GMSM01' dated '2024.11.16'. Cure for 12 hours@55°C. For use with water up to 65°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the materials are not covered by the scope of the approval.
'Wudu brand-NF 131118'. Factory applied, black coloured, two-component, water based epoxy coating. Mix in a 9:1 weight ratio and apply as per manufacturer's TDS 'PAMCN-V2', dated '20240821'. Cure for 1 hour@50°C. For use with water up to 50°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'CP231200'. Factory applied, two-part water-based epoxy coating. Mix Parts A & B in a 5:1 weight ratio and apply as per manufacturer's instructions 'File No. HBB-01', 'Version: A', dated '2024.6.30'. Cure for 24 hours@26°C. For use with water up to 23°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'90000 KANEPOX SF-A'. Factory applied, two-part, cream or red coloured epoxy coatings consisting of component A and component B. Mix and apply as per data sheet ‘Rev. No. 01’ dated January 2024. Cure for 7 days@23°C. The cream coating is for use with water up to 50°C. Between February 2024 and August 2024, the red coating is for use with water up to 23°C. From September 2024 the red coating is for use with water up to 50°C. These materials are only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the materials are not covered by the scope of the approval.
'TOHPEPOWDER#6150 SHK GRAY QD'. Factory applied, grey coloured epoxy coating. Apply as per Tohpe Corporation instructions no '4230904550B'. dated 'Jan 28, 2025'. Cure for 5 minutes@200°C. For use with water up to 65°C.
'JSGL-BFSC III A (S)'. Factory applied, grey coloured cement mortar. Mix cement:sand:water in a 1:1.7:0.5 weight ratio and apply as per manufacturer's work instructions 'JSGL/WI/14', 'Issue No. 02', 'Revision No. 00', dated '29.09.2018'. Cure for 4 hours@45°C (R.H. 85%). For use with water up to 65°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'JSGL-BFSC III B (S)'. Factory applied, grey coloured cement mortar. Mix cement:sand:water in a 1:1.7:0.5 weight ratio and apply as per manufacturer's work instructions 'JSGL/WI/14', 'Issue No. 02', 'Revision No. 00', dated '29.09.2018'. Cure for 4 hours at 45°C (R.H. 85%). For use with water up to 65°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'JSGL-BFSC (E)'. Factory applied, grey coloured cement mortar. Mix cement:sand:water in a 1:1.7:0.5 weight ratio and apply as per manufacturer's work instructions 'JSGL/WI/14', 'Issue No. 02', 'Revision No. 00', dated '29.09.2018'. Cure for 4 hours at 45°C (R.H. 85%). For use with water up to 65°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'JSGL-SRC (E)'. Factory applied, grey coloured cement mortar. Mix cement:sand:water in a 1:1.7:0.5 weight ratio and apply as per manufacturer's work instructions 'JSGL/WI/14', 'Issue No. 02', 'Revision No. 00', dated '29.09.2018'. Cure for 4 hours@45°C (R.H. 85%). For use with water up to 65°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'NextGen NP-F9500 PW'. Factory applied, blue coloured powder coating. Apply as per manufacturer's technical data sheet 'FBE/ REV00 01-02-201'. Cure for 3 minutes@240°C. For use with water up to 85°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'JERLAC Two Pack Epoxy Beige-740'. Factory applied, two-part, beige coloured epoxy coating. Mix in a 3:1 volume ratio and apply as per manufacturer's data sheet issue number '01', dated '10.01.2024'. Cure for 7 days@30°C. For use with water up to 85°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Electrocement CEM I-SR3 – Parasakti SRPC)'. Factory applied, grey coloured, Sulphate Resisting Portland Cement. Mix cement, sand & water in a 0.6 : 1.0 : 0.22 mass ratio and apply as per work instructions 'WP-08-05 I', issue '04', rev. '0' dated '22.08.2024. Cure for 24 hours@27°C. For use with water up to 65°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
‘Hempadur 35530 System’. Grey coloured, factory applied, two-component epoxy coating comprising of ‘Hempadur 35530 red (51320) and Hempadur 35530 grey (10500)’. ‘Hempadur 35530 red (51320)’ comprises of a base and curing agent which are mixed in a 3:1 volume ratio. ‘Hempadur 35530 grey (10500)’ comprises of a base and curing agent which are mixed in a 3:1 volume ratio. Apply as per manufacturer's Product Data Sheet dated October 2024. Cure for 7 days@20°C. For use with water up to 23°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Dyopox PTW Red'. Factory applied, red coloured, two-component epoxy coating. Mix base and hardener in a 2:1 weight ratio and apply as per manufacturer's datasheet 'R3 issued 2024'. Cure for 7 days@23°C. For use with water up to 50°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'NextGen NP-F9500 PW'. Factory applied, blue coloured powder coating. Apply as per manufacturer's technical data sheet 'FBE/ REV00 01-02-2019'. Cure for 3 minutes@240°C. For use with water up to 85°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'POLYGEL-2136'. Factory applied, two-part, white coloured (opaque) isophthalic gelcoat comprising of a resin and catalyst. Mix resin and catalyst in a 50:1 mass ratio and apply as per manufacturer's TDS 'Revision No. 10', dated 'SEPT 2024'. Cure for 3 hours@85°C. For use with water up to 50°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Jindal Saw Limited Ordinary Portland Cement - 53 Grade'. Factory applied, grey coloured Ordinary Portland Cement. Mix cement, sand & water in a xx ratio of 1:1.5:0.5 and apply as per manufacturer's Work Instructions 'JSAW/AP01/DISP/PRO/WI-09', version '2.0', effective date '01.05.2023'. Cure for 2.5 hours@48°C and then 3 days@30°C. For use with water up to 60°C.
'KLINGERSIL® C-4240'. Off-white coloured NBR/fibre gasket material manufactured by calendering. For use with water up to 85°C. For use only as a jointing/material having been tested at a reduced surface area to volume ratio. This material incorporates a natural ingredient. Please note that water companies will evaluate the evidence provided and may ask for more information and they reserve the right to refuse installation.
'KLINGERSIL® C-4430'. NBR/fibre gasket material, which is green coloured one side and white coloured the other, manufactured by calandering. For use with water up to 85°C. For use only as a jointing/gasket material having been tested at a reduced surface area to volume ratio.
Page 92 of 131
We use cookies to give you the best possible experience with WRAS. Some are essential to provide website functions and ensure the website is secure. We also use cookies to help us understand how people use the site and to make improvements. Click "Accept All" to enable recommended settings or click "Manage cookies" to adjust your settings. For more details, see our Cookie Policy.
