Range of vertical cased and insulated direct and indirect unvented stainless steel hot water storage cylinders. Fitted with a Caleffi 309463 GLD temperature and pressure relief valve sat at 6 bar & 90°C, and supplied with an inlet control group consisting of in-line pressure reducing valve (Caleffi set at 3 bar) and pressure relief valve (Caleffi CWIC200055) set at 4.5 bar, and incorporates a stainless-steel mesh and an approved check valve cartridge (verified by test suitable for backflow protection against Fluid Category 2), expansion vessel and filling loop. Maximum working pressure 4.4 bar. Maximum operating temperature 99°C.
Range wall mounted, concealed, thermostatic shower valves (chrome plated brass, trim sets) incorporating a quarter turn ceramic disc headwork that controls the flow using cube or dome type operating members. The temperature is controlled independently via a thermostatic cartridge also cube or dome type operating members. Both inlets incorporate an approved check valve cartridge, however, the complete product has not been fully tested to demonstrate it provides backflow protection. The products can be supplied with fixed arms and overhead showers. Maximum working pressure 5.0 Bar
Non-metallic materials and components comply with BS6920 at 70°C
Range of concealed, thermostatic shower valves incorporating half turn ceramic disc headworks controlling and diverting the flow and the temperature is controlled independently via a thermostatic cartridge, both using either round or square operating members. Both inlets incorporate approved check valve cartridges, however, the complete product has not been fully tested to demonstrate it provides backflow protection. The products can be supplied with wall outlets, fixed arms, shower handsets, shower hoses and overhead showers. Maximum working pressure 5.0 Bar
Non-metallic materials and components comply with BS6920 at 70°C
Wall mounted thermostatic bar shower mixer (matte black plated brass), incorporating a ceramic disc diverter headwork controlling the flow between shower handset and overhead shower with a dome type operating member and a thermostatic cartridge controlling the temperature with a dome type operating member that incorporates a manual override button. The inlets incorporate stainless-steel EPDM strainer washers and approved check valve cartridges; (however, the complete product has not been fully tested to demonstrate it provides backflow protection). The product is supplied with screwdriver operated isolation valves, an overhead shower incorporating an EPDM washer at the inlet, shower handset, shower hose incorporating an EPDM washer at the captive nut and a stainless-steel EPDM strainer washer in the conical nut & riser rail assembly. Maximum working pressure 10.0 bar.
Non-metallic materials and components comply with BS6920 at 60°C
Range of T-type thermostatic mixing valves (chrome plated brass bodies). Temperature is pre-set under fixed cap. The inlets incorporate fibre washers, stainless-steel EPDM strainer washers and approved single check valve cartridges, however, (the complete product has not been fully tested to demonstrate it provides backflow protection). The inlets for models MT503CP-ISO & MT503CP-ISOELB also incorporate screwdriver operated isolation valves. Maximum working pressure 10.0 bar
Non-metallic materials and components comply with BS6920 at 85°C
Range of wall mounted thermostatic bar shower mixers (chrome plated brass bodies), incorporating ceramic disc diverter controlling the flow with a dome type operating member. The temperature is controlled independently via a thermostatic cartridge with a dome type operating member that incorporates a manual override button. The inlets incorporate screwdriver operated isolation valves, stainless-steel EPDM strainer washers and approved check valve cartridges, however, (the complete product has not been fully tested to demonstrate backflow protection). The products are supplied with a shower handset, shower head, hose, and riser rail assembly. Maximum working pressure 10.0 bar.
Non-metallic materials and components comply with BS6920 at 60°C
Range of wall mounted thermostatic bar shower mixers (chrome plated brass bodies), incorporating quarter turn ceramic disc headworks controlling the flow with a dome type operating member. The temperature is controlled independently via a thermostatic cartridge with a dome type operating member that incorporates a manual override button. Model RYBS01 incorporates cube type operating members. The inlets incorporate stainless-steel EPDM strainer washers and approved check valve cartridges; however, the complete product has not been fully tested to demonstrate it provides backflow protection. The products are supplied with shower hoses, shower handsets and riser rail assemblies. Maximum working pressure 5.0 Bar
Non-metallic materials and components comply with BS6920 at 60°C
Wall mounted thermostatic bar shower mixer (matte black plated brass), incorporating a ceramic disc diverter headwork controlling the flow between shower handset and overhead shower with a dome type operating member and a thermostatic cartridge controlling the temperature with a dome type operating member that incorporates a manual override button. The inlets incorporate stainless-steel EPDM strainer washers and approved check valve cartridges; (however, the complete product has not been fully tested to demonstrate it provides backflow protection). The product is supplied with screwdriver operated isolation valves, an overhead shower incorporating an EPDM washer at the inlet, shower handset, shower hose incorporating an EPDM washer at the captive nut and a stainless-steel EPDM strainer washer in the conical nut & riser rail assembly. Maximum working pressure 10.0 bar.
Non-metallic materials and components comply with BS6920 at 60°C
Range of wall mounted thermostatic bar shower mixers, (chrome plated brass bodies), incorporating a ceramic disc diverter cartridge controlling the flow with a dome type operating member. The temperature is controlled independently with a thermostatic cartridge with a dome type operating member that incorporates a manual override button. The inlets incorporate stainless steel strainer washers, approved single check valve cartridges, however, the complete product has not been fully tested to demonstrate it provides backflow protection and screwdriver operated isolation valves. The products are supplied with a shower hose, handset, riser rail assembly and an overhead shower outlet. Maximum working pressure 10.0 bar
Non-metallic materials and components comply with BS6920 at 65°C
Wall mounted thermostatic bar shower mixer, (chrome plated brass body), incorporating a quarter turn ceramic disc headwork controlling the flow with a cubed type operating member. The temperature is controlled independently via a thermostatic cartridge with a cubed type operating member that incorporates a manual override button. The inlets incorporate stainless steel strainer washers and approved single check valve cartridges; however, the complete product has not been fully tested to demonstrate it provides backflow protection and screwdriver operated isolation valves. The product is supplied with a shower hose, handset, and riser rail assembly. Maximum working pressure 5.0 Bar
Non-metallic materials and components comply with BS6920 at 65°C
Range of thermal circulation valves with gunmetal bodies and EPDM ‘O’-rings. Models incorporate drain valves. Maximum operating pressure 16.0 bar. Maximum operating temperature 90°C.
Range of butterfly valves incorporating blue epoxy coated ductile iron bodies and discs. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Range of manually operated double regulation and commissioning valves with gunmetal bodies, incorporating a PTFE sealing ring and EPDM ‘O’- rings. Flow is controlled via a non-rising spindle headwork. Maximum working pressure 25.0 bar. Maximum operating temperature 90°C.
Range of swing gate non-return valves (resilient trim) with blue epoxy coating ductile iron bodies, epoxy coated ductile iron gate with EPDM valve seat and hydraulic damper. Maximum working pressure 16.0 bar.
Non-metallic materials and components comply with BS6920 at 80°C
Range of in-line, pressure reducing valves with DZR brass bodies and stainless-steel strainers. Maximum inlet supply pressure 16.0 bar. Outlet supply pressure is adjustable within the range of 1.5 bar to 6.0 bar. Maximum operating temperature 45°C or 65°C, please refer to model.
Range of in-line adjustable pressure reducing valves, with DZR brass bodies and EPDM membrane. Maximum inlet supply pressure 16.0 bar. Outlet pressure 1.5 bar to 6.0 bar.
Non-metallic materials and components comply with BS6920 at 80°C
Range of in-line, adjustable pressure reducing valves, with a DZR brass body. The product incorporates two approved check valve cartridges, verified by test (suitable for backflow protection against Fluid Category 3) and a shut off valve. Maximum working pressure 16 Bar Maximum outlet pressure between 1.5 bar and 6.0 bar.
Non-metallic materials and components comply with BS6920 at 40°C
Range of pressure reducing valves with DZR brass bodies. The valves are adjustable in the range of 1.5 bar - 6.0 bar. Stainless steel strainer Maximum working pressure 16.0 bar. Maximum operating temperature 80°C.
Range of core manifolds (DZR brass body) incorporating a pressure relief valve (plastic body), with an EPDM diaphragm and ‘O’-rings. For use with copper pipe (manufactured to BS EN 1057). The pressure relief valve is pre-set at 6.0 or 8.0 bar (see models). The product incorporates a check valve cartridge, verified by test (suitable for backflow protection against Fluid Category 2). Maximum operating pressure 16.0bar. Cold water use only.
Range of solenoid valves with plastic bodies and EPDM rubber diaphragms. The inlet incorporates an inner and outer plastic strainer, EPDM washer and a plastic flow regulator. Maximum working pressure 10.0 bar. Cold water use only.
Range of ‘IBall Vortex’ flow through valves with brass body and EPDM ‘O’-rings incorporating a plastic spherical valve and a drain tap. Maximum working pressure: 16.0 bar.
Non-metallic materials and components comply with BS6920 at 85°C
Lever operated spherical flow through valve with brass body and chrome plated brass ball, PTFE seals and EPDM `O` ring. The product incorporates a drain valve. Maximum working pressure 16 bar.
Non-metallic materials and components comply with BS6920 at 65°C
Range of lever operated spherical valves with brass bodies (nickel plated), chrome plated brass balls, and EPDM ‘O’-rings. Compression connections are for use with copper pipe (manufactured to EN1057). Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Screwdriver operated spherical servicing valve with chromium plated brass body, brass ball and EPDM O-rings. Maximum working pressure 5.0 bar.
Non-metallic materials and components comply with BS6920 at 85°C
In-line spherical valve with a chrome plated DZR brass body, brass ball and EPDM ‘O’-rings, incorporating a single check valve cartridge (verified by test, suitable for fluid catergory 2) with a lever operating member. To be used with copper pipe manufactured to EN1057. verified Maximum working pressure 10.0 bar. Maximum operating temperature 85°C.
Range of lever operated spherical valves with stainless steel bodies and chrome plated brass ball. Maximum working pressure 68.0 bar
Non-metallic materials and components comply with BS6920 at 80°C
Range of inline spherical valves with brushed chromium plated brass bodies and balls, PTFE seats and NBR ‘O’-rings. The valves are intended to be actuated by a motor (not supplied), but can also be screwdriver operated. Maximum working pressures: ¼” to 1” = 40.0 bar, 1¼” = 32.0 bar, 1½” to 2½” = 30.0 bar and 3” = 25.0 Bar. Maximum operating temperature 85°C.
Range of inline spherical valves with brushed chromium plated brass bodies and balls, PTFE seats and NBR ‘O’-rings. The valves are intended to be actuated by a motor (not supplied), but can also be screwdriver operated. Maximum working pressures: ¼” to 1” = 40.0 bar, 1¼” = 32.0 bar, 1½” to 2½” = 30.0 bar and 3” = 25.0 Bar. Maximum operating temperature 85°C.
Range of push-fit spherical valves with a brass body (15HSV model only) or chromium plated brass bodies (all other models), chromium plated brass ball and EPDM ‘O’- rings. SV suffix models are screwdriver operated; all other models are lever operated. For use with copper tube (manufactured to BS EN 1057), PB pipe (manufactured to BS7291-2) or PE-X pipe (manufactured to BS7291-3). Maximum working pressure and operating temperature: 12.5 @ 20°C, and 3.0 bar @ 92°C.
Range of spherical valves (shut-off, stop and servicing valves) with either acetal or POM (from 20th December 2023) bodies and a lever type or screwdriver operated operating member. For use with John Guest LLDPE pipe. Maximum working pressure: 10.0 Bar @20°C and 7 Bar @65°C. Non-metallic materials and components comply with BS6920 at 65°C.
Non-metallic materials and components comply with BS6920 at 65°C
Range of spherical (HCVB) or isolation (HBVU) valves with plastic bodies incorporating EPDM ‘O’-rings and seals. HBVU metric (mm) models are available in black or white, HBVU imperial (”) models are available in white or grey, HCVB models are available in black only. HBVU models are lever operated, HCVB models are screwdriver operated. HBVU models are for use with LLDPE pipe (manufactured to DIN 8072). The HCVB 15mm model push fit connection is for use with PEX-b pipe (manufactured to EN ISO 21003 B1) and the HCVB 22mm models push fit connection is for use with PEX pipe (manufactured to BS7291-3). Maximum working pressures: HBVU models: 10.0 bar. HCVB models: 7.0 bar (HCVB models push fit connection), barbed (spigot) connections of HCVB models are open outlet use only. Cold water use only.
Range of screw down valves with brass bodies, , EPDM washers and PTFE seats. Compression connection to be used with copper pipe manufactured to EN1057. Maximum working pressure 16 bar. Maximum operating temperature 85°C.
Talbot range of gunmetal screw down stop valves for use with MDPE PE80 pipe (manufactured to EN12201). The products are supplied with loose (blue plastic) pipe inserts. Maximum working pressure 16.0 bar. Cold water use only.
Range of brass stopcock incorporating EPDM and PTFE washers. Compression connections, to be used with copper pipe EN1057 only. Maximum working pressure 16.0 bar.
Non-metallic materials and components comply with BS6920 at 85°C
Range of screw down stop valves with plastic bodies, EPDM washers and ‘O’ rings. For use with polyethylene pipe (manufactured to EN 12201). The products are supplied with loose pipe inserts. For above and below ground use. Maximum working pressure 16 bar. Cold water use only.
Range of front loading commercial washing machines with flow controlled by solenoid valves and discharged via a type `AD` airgap (verified by test - suitable for backflow protection against fluid category 5). The products are supplied with a dual layer composite supply hose (blue outer/black inner). Maximum working pressure 5.0 bar. Cold water use only
Range of commercial dish washing machines with flow controlled by a solenoid valve and discharged via a type `AB` airgap (verified by test - suitable for backflow protection against fluid category 5). Maximum working pressure 4.0 bar. Cold water use only.
'Support Ring F1'. White coloured, injection moulded acetal support ring. For use with water up to 85°C.
'XXDT ST'. White coloured, dry pressed and sintered, ceramic disc. For use with water up to 85°C.
'SEDALOX Ceramic Disc'. White coloured ceramic disc manufactured by dry-press. For use with water up to 85°C.
'CEC-GFS Enamel, Black Blue RAL5004'. Factory applied, blue/black (appears black) coloured, enamel coating. Apply as per manufacturer's instructions 'ZZ-Ins001', dated '2021.01.01'. GFS-G base glaze: dry for 15 Minutes at 200°C then fire for 12 minutes at 870ºC. GFS-S surface glaze: dry for 15 Minutes at 200°C then fire for 10 minutes at 830ºC. For use with water up to 85°C. This material is only approved for the drying and firing conditions that appear on the approval. If the drying and/or firing are varied from those specified on the approval then the material is not covered by the scope of the approval.
'GCF-SRC'. Factory applied, grey coloured cement mortar. Mix sand, cement and water in a ratio of 4:2:1 and apply as per manufacturer's instructions 'QC-WI-8.1.8, revision 2/0, issue date 30/10/2021'. Cure for 28 days@24°C. For use with water up to 65°C. This material is only approved for the mixing & curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'RF (Riyadh Foundry)'. Factory applied, grey coloured cement. Mix cement, sand and water in a 1:1.5:0.6 weight ratio and apply as per manufacturer's work instruction 'WI.PR.07', revision '01/01/', dated '16.02.2022'.. Cure for 3 hours@25°C. For use with water up to 85°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
‘Promag’. Factory applied, black coloured PUR coating system comprising of a primer and topcoat. ‘Promag Primer’ is a two-part primer to be mixed in a 1:2 mass ratio before applying as per manufacturer’s core instructions ‘TLB: 10000043811’, ‘Version: M’. Cure/dry for 2 hours@23°C. ‘Promag Topcoat’ is a three-part topcoat to be mixed in a 92.59:5.19:2.22 mass ratio before applying as per manufacturer’s core instructions ‘TLB: 10000043811’, ‘Version: M’. Cure/dry for 20 seconds@20-26°C. For use with water up to 23°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'CPT CML Variation No.2 cementitious mortar’ for use with ‘Conplast RP264 Admixture'. Site applied, grey coloured (once mixed) cementitious mortar and admixture. 'CPT CML Variation No.2 cementitious mortar’ comprises of cement, sand and Microsilica. Mix cement and sand dry in a 1:1.1 mass ratio. Add the microsilica in a 1:0.05 mass ratio with the cement content. Add water in a cement/water mass ratio of 1:0.32. Add the admixture in an admixture/ cement ratio of 8ml:1000g. Mix rigorously until an even consistency is achieved and apply as per manufacturer’s instructions reference ‘2328’, dated 13/01/2023. Cure for 28 days@ between 10°C and 35°C. For use with water up to 60°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Weberdry epo PW'. Site applied, light grey coloured (once mixed), two-component epoxy coating. Mix Part A (light grey coloured) with Part B (translucent, yellow coloured) in a weight ratio of 100:20. Apply as per manufacturer's TDS 'Edition: 04.23-A'. Cure for 24 hours@25°C. Mix and apply a second coat in the same way and then cure for 14 days@25°C. For use with water up to 23°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Aquastore'. Grey coloured, GRP panels manufactured by hydraulic press. For use with water up to 60°C.
'Aquasystem'. Grey coloured, GRP panels manufactured by hydraulic press. For use with water up to 60°C.
'Aquatank'. Grey coloured, GRP panels manufactured by hydraulic press. For use with water up to 60°C.
‘PureOne hose’ (formerly known as ‘Clearwater hose’). Multi-layered hose manufactured on a mandrill by hand, consisting of a colourless, transparent PE inner layer and a blue coloured EPDM outer layer. Please note that the hose has many layers but the approval describes only the inner and outer layers. For use with water up to 50°C.
Page 8 of 28
We use cookies to give you the best possible experience with WRAS. Some are essential to provide website functions and ensure the website is secure. We also use cookies to help us understand how people use the site and to make improvements. Click "Accept All" to enable recommended settings or click "Manage cookies" to adjust your settings. For more details, see our Cookie Policy.
