Range of draining taps with DZR brass, brass or chrome plated brass bodies. Incorporating a rising spindle headwork, EPDM or NBR seals and washers. Maximum working pressure 16.0 bar.
Non-metallic materials and components comply with BS6920 at 85°C
Range of stainless steel braided PEX lined flexible hose assemblies, incorporating EPDM O-Rings and gaskets. Maximum working pressure 10.0 bar.
Non-metallic materials and components comply with BS6920 at 70°C
Range of stainless steel braided, PEX lined flexible hose assemblies incorporating various end connections. The hoses are supplied with NBR O-rings. Maximum working pressure 10.0 bar.
Non-metallic materials and components comply with BS6920 at 85°C
Range of stainless steel interlocked shower hose with PVC/silicon/PEX inner hoses and various end connections. Maximum operating temperature 65°C.
Range of nylon braided hoses with TPSiV inner liner and brass end connections incorporating EPDM washers.Open outlet use only.
Non-metallic materials and components comply with BS6920 at 65°C
Range of PVC shower hoses with a black PVC inner liner (with a black and silver striped appearance). Hose end connections and nuts are available in brass, plastic or stainless steel, (all chrome plated), with either EPDM (black) or silicone (white) washers. BS6920 65°C.
Range of stainless steel braided, EPDM lined flexible hose assemblies with various brass end connections. The hoses are supplied with EPDM O-rings or washers. Maximum working pressure 10.0 bar.
Non-metallic materials and components comply with BS6920 at 85°C
Range of shower hoses with TPE linings and EPDM ‘O’-rings. Maximum operating temperature 60°C. Open outlet use only.
Range of vertical cased and insulated direct and indirect unvented stainless steel hot water storage cylinders. Fitted with a Caleffi 309463 GLD temperature and pressure relief valve sat at 6 bar & 90°C, and supplied with an inlet control group consisting of in-line pressure reducing valve (Caleffi set at 3 bar) and pressure relief valve (Caleffi CWIC200055) set at 4.5 bar, and incorporates a stainless-steel mesh and an approved check valve cartridge (verified by test suitable for backflow protection against Fluid Category 2), expansion vessel and filling loop. Maximum working pressure 4.4 bar. Maximum operating temperature 99°C.
Range of wall mounted, thermostatic shower valves (chrome plated brass bodies), model (OP TS1503 SCL C) incorporates a single sequential headwork controlling both flow and temperature. Model (TS1503ECP-2000-MK) incorporates a thermostatic mixing cartridge that only controls the temperature. The inlets incorporate flow regulators, plastic strainers and approved single check valve cartridges (however, the complete product has not been fully tested to demonstrate that it provides adequate backflow protection). Maximum working pressure 10.0 bar.
Non-metallic materials and components comply with BS6920 at 65°C
‘J9’ (wafer type) & ‘L9’ (lug type) ranges of butterfly valves with blue epoxy coated ductile iron (128xxx) or stainless steel bodies (628xxx), stainless steel discs and EPDM seats. The products are supplied with either a lever, gearbox (below DN250), electric or pneumatic actuating operating members. Maximum working pressure 16.0 bar.
Non-metallic materials and components comply with BS6920 at 85°C
Range of butterfly valves with ductile iron bodies (blue epoxy coating), EPDM seats and `O` rings. Gearbox and handwheel Maximum working pressure 16.0 bar. Maximum operating temperature 80°C.
Range of wafer, lug type and double flanged butterfly valves incorporating blue epoxy coated ductile iron bodies, either stainless steel (CF8 or CF8M) or blue epoxy coated ductile iron discs and an EPDM seat. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Non-metallic materials and components comply with BS6920 at 85°C
Range of wafer, lugged and double flanged type butterfly valves (with blue epoxy coated ductile iron bodies, and either a stainless steel or grey epoxy coated ductile iron disc with an EPDM liner. Maximum working pressure 16.0 Bar (DN50 to DN800) or 10.0 Bar (DN900 to DN1200)
Non-metallic materials and components comply with BS6920 at 60°C
Range of butterfly valves with blue epoxy coated ductile iron bodies and discs, and EPDM seals with handwheel gear operating members. Maximum working pressure – 10 bar or 16 bar, see models. Maximum operating temperature – 23°C.
Range of concealed two way & three way ceramic disc diverters, (brass bodies – various trim sets and operating members). Maximum working pressure: 10.0 Bar
Range of spring-loaded resilient trim, non-return valves with blue epoxy coated ductile iron bodies, stainless steel discs and EPDM seals. Maximum working pressure 16.0 bar. Maximum operating temperature 80°C.
Range of pilot operated pressure reducing valves with blue epoxy coated ductile iron bodies. The valves have an adjustable pressure reducing facility controlled via a pilot valve (with an operating range of 1 to 6 bar), with auxiliary components including stainless steel tubing, fittings and spherical valves. Maximum working pressure 16.0 bar. Maximum operating temperature 23°C.
Range of solenoid valves with a brass body and an EPDM diaphragm and gasket. For use with copper pipe (manufacture to EN1057). Maximum working pressures: X210525720001aa, X210525720002aa, X210525720101aa and X210525720102aa models 10.0 bar. X210525720011aa and X2105257201111aa models: 3.0 bar.
Non-metallic materials and components comply with BS6920 at 85°C
A range of in-line, lever operated spherical isolation valves with chrome plated brass bodies & chrome plated balls, stainless steel wire filters and plastic flow regulators. Compression connections to be used with copper pipe EN1057 only. Maximum working pressure 10.0 bar.
Non-metallic materials and components comply with BS6920 at 60°C except for models AI-811215 & AI-81121518 CST with temperatures of 85°C
Range of lever operated spherical valves with stainless steel bodies and ball with PTFE seats. Maximum operating pressure 16.0 bar (2019S) or 63.0 bar (2013ND & 2006SC-FW).
Non-metallic materials and components comply with BS6920 at 85°C
Range of stainless steel spherical valves, incorporating T-type or single lever operating members with a stainless steel ball and PTFE seats. Maximum working pressure 63.0bar
Non-metallic materials and components comply with BS6920 at 80°C
Range of stainless-steel spherical valves, incorporating a stainless-steel ball, PTFE seats and EPDM ‘O’-rings with single lever operating members. Maximum working pressure 63.0 Bar. Maximum operating temperature 23.0°C
Range of gates valve with ductile iron bodies (blue epoxy coating), EPDM seats and `O` rings. The valves are handwheel operated via a non-rising spindle. Maximum working pressure 16.0 bar. Maximum operating temperature 80°C.
Range of gate valves with blue epoxy coated ductile iron bodies, EPDM coated ductile iron wedges, EPDM gasket and ‘O’-ring. The valves operate via non-rising spindle headwork with a hand wheel operating member. Maximum working pressures: DN50: 25.0 bar, DN65-DN600: 16.0 bar.
Non-metallic materials and components comply with BS6920 at 85°C
Range of cast iron gate valves with blue epoxy coating, EPDM coated disc, PTFE gasket and EPDM seals. The valves are operated via a non-rising spindle headwork with a hand wheel operating member. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Range of resilient seated gate valves with cast iron bodies (blue epoxy coated), EPDM coated cast iron wedges and a handwheel operating member. Maximum working pressure 16.0 bar.
Non-metallic materials and components comply with BS6920 at 85°C
Range of cast iron gate valves with blue epoxy coating, EPDM coated disc, PTFE gasket and EPDM seals. The valves are operated via a non-rising spindle headwork with a hand wheel operating member. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Non rising screw down angled stop valve, with a chrome plated brass body and NBR washer. Maximum working pressure 10.0 Bar
Non-metallic materials and components comply with BS6920 at 85°C
‘V-PET#1600 Gray F’. Factory applied, dark grey coloured epoxy resin powder coating. Apply as per manufacturer’s instructions ‘ref.no. VP1600-PD-170412’, dated '12th April 2017'. Cure for 10 minutes@200°C. For use with water up to 60°C. This material is only approved for the curing conditions that appear on the approval. If the curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
‘PULRON 101 AQUA’. Factory applied, green coloured polyethylene coating. Apply a single coat (200μm thickness) as per manufacturer's instructions 'ELS.TT.C01.40', 'Rev00', dated '13.06.2023', Cure for 10 minutes at 200°C. Between June 2023 and December 2024, the material was for use with water up to 23°C. Between January 2025 and June 2028, the material is for use with water up to 65°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
Non-metallic materials and components comply with BS6920 at 65°C°C
'EPW-6575S8T-20 Epoxy RAL 5005'. Factory applied, blue coloured epoxy powder coating. Apply as per manufacturer's TDS 'Rev:00/December 2022'. Cure for 10 minutes at 200°C. For use with water up to 23°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Interpon HYF PLUS HJ701I'. Factory applied, blue coloured epoxy coating. Apply as per manufacturer's product datasheet 'Ed.3 – October 2014' and stove/cure for 20 minutes@200°C. For use with water up to 85°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Sheraplex Blue, Black, Green & Silver'. Factory applied, organic resin coating system, consisting of a primer and 'Delta Seal' topcoat (available in blue, black, green and silver colours). Apply one coat of primer (as per instructions: WI.BMC.W02 Issue 2 - February 2005) and cure for 2 and ½ hours at 380°C. Then apply a passivation layer through immersion for 15 minutes at 76-99°C (as per instructions: WI.BMC.W06 Issue 1 August 2004). Apply 1 topcoat of 'Delta Seal' (as per instructions WI.BMC.W01A Issue 2 August 2010) and cure for 20 minutes at 200°C. All are for use with water up to 23°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'VPC5009 Potable FBE'. Factory applied, blue coloured epoxy powder coating. Pre-heat substrate at 200°C and then apply by dipping in a fluidised bed as per manufacturer's instructions dated 10th January 2019. Cure for 15 minutes@200°C. For use with water up to 23°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Unisilkon L200'. White coloured silicone grease intended for use as a lubricant. For use with water up to 85°C.
'Tefzel® ETFE 200, 207, 280, 750, HT2181, HT2183 & HT2185'. Un-pigmented (white coloured), compression moulded ETFE material. For use with water up to 85°C.
'TamAcryl 2000 Orange or Blue with corrosion inhibitor', orange coloured or blue coloured (once mixed), site applied acrylic grouts. Mix Part A (orange or blue) with 2% accelerator and then mix with Part B (colourless) in a 1:1 volume ratio. Apply as per manufacturer’s TDS 'V1UK20 – 2020.10.22'. Cure for 12 hours at 16°C. For use with water up to 23°C. This material is only approved for the mixing & curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval. These materials are for use in concrete reservoirs and similar structures, constructed in accordance with the design criteria of BS EN 1992-3:2006 (Design of concrete structures – Liquid retraining and containing structures) with respect to normal frequency of joints. The material has been tested at a reduced surface area to volume ratio of 1000mm² per litre.
'TamPur 150'. Site applied, Hydrophilic polyurethane foam which is an amber coloured liquid when unreacted and a pale yellow coloured, flexible foam material when cured. Mix TamPur 150 with water in a volumetric ratio of 1:1 and apply as per manufacturer’s TDS 'V1UK19 – 2019.4.25'. Cure for 24 hours at 7°C. For use with water up to 23°C. This material is only approved for the mixing & curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval. These materials are for use in concrete reservoirs and similar structures, constructed in accordance with the design criteria of BS EN 1992-3:2006 (Design of concrete structures – Liquid retraining and containing structures) with respect to normal frequency of joints. The material has been tested at a reduced surface area to volume ratio of 1000mm² per litre.
Range of wall mounted, electronically controlled combination tap assemblies, (chrome plated brass or stainless steel bodies). The flow is controlled by a solenoid valve that is activated via an infra-red sensor The spout outlet incorporates a plastic aerator. The product incorporates a stainless steel braided PEX lined flexible connection hose assembly, connecting the spout to the solenoid valve. Maximum working pressure 8.0 Bar
Non-metallic materials and components comply with BS6920 at 65°C
Range of electronically operated combination tap assemblies, (chrome plated brass bodies). The flow is controlled by a solenoid valve which is actuated via an infrared sensor. The spout outlet incorporates a plastic aerator. The product incorporates a stainless steel braided PEX lined flexible connection hose, connecting the tap to the solenoid valve. Maximum working pressure 8.0 Bar
Non-metallic materials and components comply with BS6920 at 65°C
Range of wall mounted, single-hole, single outlet, electronically controlled combination tap assemblies, (chrome plated brass or stainless steel bodies). The flow is controlled by a solenoid valve activated via an infra-red sensor. The spout outlet incorporates a plastic aerator. The products incorporate a stainless steel braided PEX lined flexible hose assembly, connecting the spout to the solenoid valve. Maximum working pressure 8.0 Bar.
Non-metallic materials and components comply with BS6920 at 65°C
Range of deck mounted taps for cold or premixed water with stainless steel bodies. Flow is controlled by a solenoid valve activated via an infra-red sensor, and the spout outlet incorporates a plastic aerator. Supplied with a stainless steel braided PEX lined flexible connection hose. Maximum working pressure 8.0 bar.
Non-metallic materials and components comply with BS6920 at 65°C
Range of tundishes incorporating a plastic or coated, mild steel body. Maximum operating temperature 85°C.
Range of single hole, single outlet (swivel nozzle) tap (chrome plated brass) incorporating ceramic cartridge headwork with single lever operating member. The spout outlet incorporates a plastic aerator. Maximum working pressure 10 bar. Maximum operating temperature 60°C.
Range of ceramic cartridge headworks with plastic bodies and NBR seals and O-rings. For insertion into specifically dimensioned bores. Maximum working pressure 5.0 Bar
Non-metallic materials and components comply with BS6920 at 85°C
Range of overhead shower outlets, (chrome plated ABS bodies). The inlets incorporate a plastic flow regulator. Maximum operating temperature 65°C.
Range of overhead shower outlets, (chrome plated ABS bodies). The inlets incorporate a plastic flow regulator. Maximum operating temperature 65°C.
Range of single hole, single outlet (fixed) combination tap assemblies (brass bodies with various finishes), incorporating a ceramic cartridge headwork with single lever operating members. The spout outlets incorporate a plastic aerator. Maximum working pressure 5.0 bar. Maximum operating temperature 60°C.
Wall mounted two-hole, single outlet (fixed) combination tap assemblies (chromium plated brass) incorporating a ceramic cartridge headworks with single lever operating members and a self-cancelling diverter to shower outlet. The spout outlets incorporate a plastic flow straightener, and the product is supplied with a single check valve cartridge on the shower outlet (however, the complete product has not been fully tested to demonstrate it provides adequate backflow protection). Maximum working pressure 10.0 Bar.
Non-metallic materials and components comply with BS6920 at 60°C
Page 8 of 21
We use cookies to give you the best possible experience with WRAS. Some are essential to provide website functions and ensure the website is secure. We also use cookies to help us understand how people use the site and to make improvements. Click "Accept All" to enable recommended settings or click "Manage cookies" to adjust your settings. For more details, see our Cookie Policy.
