'Epoxy PB Pipe Green (W) & Epoxy FB Pipe Green (HW)'. Factory applied, green coloured epoxy powder coatings. The substrate to which the coating is to be applied is pre-heated to 220˚C for 15 minutes before applying the coating as per product data sheet dated '27th June 2023'. Post-cure for 15 minutes@215°C. For use with water up to 85°C. This material is only approved for the pre-heat and post-cure conditions that appear on the approval. If the pre-heat and/or post-cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'HKUST002'. Factory applied, blue coloured epoxy coating. Apply as per manufacturer's instructions 'HKUST002101001', '01', dated '03/11/2020'. Cure for 168 hours@25°C. For use with water up to 23°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
‘Primer coating Spu‐221(A) & Spu‐221(B)’ for use with ‘Top coating: Spu‐222(A) & Spu‐222(B)’. Factory applied, grey coloured (once mixed) Acrylic Polyurethane primer & coating. Mix parts A and B of the primer in a 4:1 volume ratio and apply as per manufacturer’s instructions dated 5th May 2018. Cure for 48 hours@25°C. Mix parts A and B of the topcoat in a 4:2 volume ratio and apply as per manufacturer’s instructions dated 5th May 2018. Cure for 48 hours@25°C. For use with water up to 40°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
‘FIBER TECH 82’. Factory applied, natural (appears dark yellow) fibreglass resin. Spray apply as per manufacturer’s Method Statement Ref ‘PP-GRP-092021-R1’, dated ‘21 Sept 2020’. Cure for 72 hours@25°C. For use with water up to 40°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
‘Nitocote EP405 (3821)’. Site applied, blue coloured, two component solvent free epoxy resin coating consisting of two bases (coat 1 base; Nitocote EP405 white & coat 2 base; Nitocote EP405 blue) & clear EP405 hardener. Mix parts A & B of each coat in a 100:13 weight ratio and apply in accordance with Fosroc data sheet issue 7 (CI/SfB: Pn6) dated November 2013. Cure coat 1 for 18 hours@7°C. Cure coat 2 for 21 days@7°C. For use with water up to 23°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
‘MoyaProof WS2’. Site applied, grey coloured (once mixed), two-component, polymer modified Portland cement based cementitious waterproofing membrane. Mix Part A (white, opaque liquid) with Part B (grey, opaque powder) in a 1:4 mass ratio and apply two coats as per manufacturer’s Technical Datasheet ‘CC/MP05/Ver09/01/21’. Cure Coat 1 for 2 hours at 5˚C. Cure Coat 2 for 28 days at 5˚C. For use with water up to 23°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Renderoc Plug 20'. Site applied, dark grey coloured, cementitious repair mortar. Mix with water in a 3:1 volume ratio and apply as per manufacturer's datasheet '14' dated 'June 2018'. Cure for 21 days@7°C. For use with water up to 23°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Fusamatic Electrofusion Fittings'. Black coloured, injection moulded, polyethylene Electrofusion Fittings (made in UK from Ineos Eltex TUB121 & Hostalen CRP 100 Resist CR Black). In December 2023, Electrofusion Fittings made in Anhui Province China from Borouge Borsafe HE3490-LS & Hostalen CRP 100 Resist CR black were added to the approval. For use with water up to 60°C.
'Fusamatic Electrofusion and Spigot Fittings'. Black coloured, injection moulded, polyethylene Electrofusion and Spigot Fittings (made from Ineos Eltex TUB121, Hostalen CRP 100 Resist CR Black & Borouge Borsafe HE3490-LS). For use with water up to 60°C.
'Fusamatic Electrofusion and Spigot Fittings'. Black coloured, injection moulded, polyethylene Electrofusion and Spigot Fittings (made from Ineos Eltex TUB121, Hostalen CRP 100 Resist CR Black & Borouge Borsafe HE3490-LS). For use with water up to 60°C.
'DIC.PPS FZ-2140-F3 BLACK'. 'DIC.PPS FZ-2140-F3 BLACK-U' was added to the approval in September 2023. Black coloured, injection moulded PPS materials manufactured in Vienna, Austria. For use with water up to 85°C.
'Tefzel® ETFE 200, 207, 280, 750, HT2181, HT2183 & HT2185'. Un-pigmented (white coloured), compression moulded ETFE material. For use with water up to 85°C.
‘Sikadur 31 DW Rapid for use with Combiflex TF Tape’. Site applied, grey coloured two-component epoxy resin for use with grey coloured TPE Tape. Mix parts A & B of ‘Sikadur 31 DW Rapid’ in a 3:1 weight ratio and apply as per product data sheet ‘March 2021, Version 01.03’. Immediately apply ‘Combiflex TF Tape’ as per product data sheet ‘May 2021, Version 01.01’ and cure for 7 days@7°C. For use with water up to 23°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
‘Sikadur 31 DW for use with Combiflex TF Tape’. Site applied, grey coloured two-component epoxy resin for use with grey coloured TPE Tape. Mix parts A & B of ‘Sikadur 31 DW’ in a 3:1 weight ratio and apply as per product data sheet ‘February 2022, Version 03.03’. Immediately apply ‘Combiflex TF Tape’ as per product data sheet ‘May 2021, Version 01.01’ and cure for 7 days@7°C. For use with water up to 23°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'212N' components. Black coloured, injection moulded EPDM rubber components with a shore hardness of 70. ‘O’ rings (in-radius 1.31mm), washers (in-radius 1.05mm) & membranes (in-radius 1.75mm) made in Italy. ‘O’ rings (in-radius 1.31mm) & washers (in-radius 1.05mm) made in China. For use with water up to 85°C. When processing an application for a Product Approval incorporating these components, these are the only shapes covered by the approval.
'210N' components. Black coloured, injection moulded NBR rubber ‘O’ rings, washers and lip seals. Shore hardness 70. The ‘O’ rings have an in-radius of 1.31mm, the washers 1.05mm and the lip seals 0.45mm. For use with water up to 60°C.
Range of wall mounted, single-hole, single outlet (fixed) electronically controlled combination tap assemblies (chrome plated brass or stainless-steel bodies) which are supplied with pre-mixed water. Flow is controlled via an infra-red activated solenoid valve and the spout outlets incorporate plastic aerators. Maximum working pressure 8.0 bar
Non-metallic materials and components comply with BS6920 at 65°C
Bottom entry BS1212-4 (2016) compact type float operated valve for WC flushing cisterns. The inlet incorporates a flow restrictor. Maximum working pressure 10.0 bar. Cold water only
Side entry BS1212-4 (2016) compact type float operated valve for WC flushing cisterns. Maximum working pressure 10.0 bar. Cold water use only.
Side entry BS1212-4 fill valves with plastic bodies. Maximum working pressure 10.0 bar. Coldwater use only.
Range of bottom entry BS1212-4 telescopic fill valves with plastic bodies. Maximum working pressure 10.0 bar. Cold water use only.
WC flushing cistern incorporating a side entry BS 1212-4 compact type float operated inlet valve providing a Type AG air gap with a dual flush drop valve for full flush volumes of up to 6 litres and a reduced flush of up to 4 litres. The cistern is operated by electronic or manual actuation. Maximum working pressure 10.0 bar. Cold water use only
Range of Concealed WC dual flushing cistern with a vertical BS 1212-4(2016) float operated inlet valve providing a Type AG air gap arrangement and a dual flush outlet valve. The flush volume is operated by a two-push button assembly. Maximum working pressure -10 Bar Maximum operating temperature - cold water use only Models T1910 & T1911 can now incorporate a T8702 flush valve. Maximum working pressure 10 Bar, cold water use only.
Range of concealed WC dual flushing cisterns with a vertical BS 1212-4(2016) float operated inlet valve providing a Type AG air gap arrangement and a dual flush outlet valve. The flush volume is operated by a two-push button assembly. The product also incorporates a servicing valve and flexible hose on the inlet supply. Maximum working pressure 10 Bar, cold water use only.
Range of tundishes incorporating a plastic or coated, mild steel body. Maximum operating temperature 85°C.
Range of aerator kits incorporating plastic flow regulators (1.9l/min, 3.5l/min & 5.0l/min) with plastic bodies and EPDM ‘O’ rings. Plastic adaptors, NBR washers and chromium plated brass housings may also be supplied as part of the kit. Maximum operating temperature 65°C.
Range of ceramic cartridge headworks with plastic bodies & silicone rubber seals. For insertion into specifically dimensioned bores. Maximum working pressure 16.0 Bar.
Non-metallic materials and components comply with BS6920 at 80°C
‘VT30’ range of thermostatic cartridges with a plastic body and EPDM ‘O’-rings and stainless steel strainers. For insertion into specifically dimensioned bores. Maximum working pressure 16.0 bar. BS6920 70°C.
Range of single hole, single outlet (fixed) combination tap assemblies (brass bodies - various finishes), incorporating ceramic cartridge headworks, with single lever or dome type operating members. The spout outlet incorporates a plastic aerator. Some models are supplied with a lever type pop up waste (see models) Other models are supplied with a permanently open waste set. Maximum working pressure 10.0 Bar Maximum operating temperature 70.0°C
Non-metallic materials and components comply with BS6920 at 70°C
Range of overhead shower outlets, (chrome plated ABS bodies). The inlets incorporate a plastic flow regulator. Maximum operating temperature 65°C.
Range of single hole, single outlet (fixed) combination tap assemblies (brass bodies - various finishes), incorporating a ceramic cartridge headwork with a single lever operating member. The spout outlets incorporate a plastic aerator. Some products are supplied with a lever type or click-type pop up waste. Maximum working pressure 10.0 bar.
Non-metallic materials and components comply with BS6920 at 60°C
Single-hole, single outlet (swivel) combination tap assembly, (stainless steel body - various finishes), incorporating a ceramic cartridge headwork with a single lever operating member. The spout outlet incorporates a plastic aerator. Maximum working pressure 10.0 bar. Maximum operating temperature 65°C.
Range of single hole, single outlet (swivel) combination tap assemblies (brass bodies - various finishes). Models (F1021 & F7132B) incorporate quarter turn ceramic disc headworks with either single lever or cross-top type operating members. Models (F1025X, F1026 & F7149) incorporate ceramic cartridge headworks with single lever operating members. All spout outlets incorporate plastic aerators. Maximum working pressure 10.0 bar. Maximum operating temperature 65°C.
Two hole, single outlet (fixed) combination tap assembly (chromium plated brass). Incorporating quarter turn ceramic disc headworks and single lever operating members. The spout outlet incorporates a plastic aerator and the product is supplied with metal backnuts. Maximum working pressure 10 bar. Maximum operating temperature 60°C
Range of two-hole, single outlet (fixed) combination tap assemblies (brass bodies - various finishes), incorporating quarter turn ceramic disc headworks with cross top operating members and a manual diverter to shower outlet. The products are supplied with metal back nuts. Maximum working pressure 10.0 Bar
Non-metallic materials and components comply with BS6920 at 65°C
Range of two-hole, single outlet (fixed) combination tap assemblies, (brass bodies - various finishes), incorporating quarter turn ceramic disc headworks with single lever type operating members and a manual diverter to shower outlet. The products are supplied with metal back nuts. Maximum working pressure 10.0 Bar
Non-metallic materials and components comply with BS6920 at 65°C
Range of two-hole, single outlet (fixed) combination tap assemblies with (brass bodies - various finishes) incorporating quarter turn ceramic disc headworks with single lever operating members and a manual diverter to shower outlet. The products incorporate waterfall type spout outlets with stainless steel strainers. Maximum working pressure 10.0 Bar
Non-metallic materials and components comply with BS6920 at 65°C
Wall mounted, two hole, single outlet (fixed) combination tap assembly (brass body - various finishes), incorporating a ceramic cartridge headwork with a single lever operating member and a self-cancelling diverter to a shower outlet. The shower outlet connection incorporates an approved check valve cartridge, however, the complete product has not been fully tested to demonstrate it provides backflow protection and the spout outlet incorporates a plastic aerator. Product is not supplied with shower hose and handset. Maximum working pressure 10.0 Bar
Non-metallic materials and components comply with BS6920 at 70°C
Range of four-hole, single outlet combination tap assemblies (brass or stainless steel bodies, various finishes - see model). The product incorporates a ceramic cartridge headwork controlling the temperature and flow to the shower handset, and a quarter turn ceramic disc headwork controlling the flow via a separate thermostatic cartridge to an outlet (spout not supplied), all with single lever operating members. The product is supplied with a shower hose and handset. The shower handset incorporates an approved check valve cartridge, however, the complete product has not been fully tested to demonstrate it provides backflow protection. Maximum working pressure 10.0 bar.
Non-metallic materials and components comply with BS6920 at 60°C
Range of activated carbon filter cartridges and heads, with plastic bodies. Maximum operating pressure 8.6 bar. Cold water use only.
Range of JG Twist & Lock Speedfit push-fit fittings for use with JG Speedfit Layflat Polybutylene Barrier Pipe (BPB Pipe to BS EN 7291-2:2010), 'BPEX' Barrier Pipe.(BPEX Pipe to BS EN 7291-3:2010) and Copper Pipe to BS EN1057:2006 Max working pressure & operating temperature: 12.5 Bar at 20°C 6.0 Bar at 83°C
‘Atlas’ range of green fusion welded polypropylene fittings for use with ‘Atlas’ PPRGF or PPR pipes. Maximum working pressure 20.0 bar. Cold water use only.
‘F18’ range of brass press fittings (TH and U crimp profiles) with EPDM ‘O’-rings for use with Rifeng B1 PEX/AL/PEX multilayer pipe. Maximum working pressure 10.0 bar. Maximum operating temperature 95°C.
Range of brass press fittings (TH and U crimp profiles) with EPDM ‘O’-rings for use with RIIFO B1 PEX/AL/PEX multilayer pipe. Maximum working pressure 10.0 bar. Maximum operating temperature 95°C.
U Profile range of press fittings incorporating EPDM ‘O’-rings. For use with Mingshi (S-1-0509/10/11/12/17/13) PEX-AL-PEX pipe. Maximum working pressure 10.0 bar. Maximum operating temperature 95°C
Range of ‘Henco Profit Synthetic’ pushfit fittings with PPS (HPK models) or brass (HP models) bodies and EPDM o-rings, to be used with ‘Henco RIXc’ PEXc/Al/PEXc multilayer pipes. Maximum working pressure 10.0 bar. Maximum operating temperature 95°C.
Fluxo range of Brass & PPSU crimp fittings for use with ‘Fluxo’ PEX/Al/PEX Multilayer Pipe. Crimp joint is achieved by a TH profile crimp jaws. Maximum working pressure 10bar @ 70°C, 6Bar @ 95°C.
Range of brass (Series 1000 & 1100) and DZR brass (Series 1100CZ) compression fittings, various finishes. For use with copper tube EN1057. Maximum working pressure 30.0 bar. Maximum operating temperature 100°C.
Range of copper and brass press-fit fittings with HNBR o-rings, for use with copper tube manufactured to EN1057. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Supreme S16 range of fittings for use with PE pipes (manufactured to EN12201-2). Supplied with a plastic pipe support liner For above and below ground use. Maximum working pressure 16.0 bar. Cold water use only.
Page 46 of 64
We use cookies to give you the best possible experience with WRAS. Some are essential to provide website functions and ensure the website is secure. We also use cookies to help us understand how people use the site and to make improvements. Click "Accept All" to enable recommended settings or click "Manage cookies" to adjust your settings. For more details, see our Cookie Policy.
