In line isolation valve with DZR brass body, DZR brass ball (chrome plated), and an EPDM inlet washer. The product incorporates two approved check valve cartridges, one either side of the spherical valve, verified by test (suitable for backflow protection against Fluid Category 3). Maximum working pressure 16.0 bar. BS6920 85°C.
Pairs of angled spherical valves with DZR brass bodies (chrome plated), brass ball (chrome plated), stainless-steel strainer, and an approved check valve cartridge, however, the complete product has not been fully tested to demonstrate it provides backflow protection. The compression connections are for use with copper pipe (manufactured to EN1057). Maximum working pressure 10.0 bar. Maximum operating temperature 85°C
Range of pressure reducing valve assemblies with DZR brass bodies incorporating a spherical valve, a pressure gauge and 2 inline check valve cartridges, verified by test (suitable for backflow protection against Fluid Category 3). Models TVAP250001 & TVAP250005 also incorporate a water meter port. Maximum supply pressure 16 bar. Outlet pressure setting is adjustable in the range 1.5 to 6 bar.
Non-metallic materials and components comply with BS6920 at 65°C
Tenant valve assemblies with a DZR brass body consisting of water meter manifold, servicing valve and a pressure reducing valve (adjustable between 1.0 and 6.0 bar). The inlet incorporates two approved check valve cartridges, verified by test (suitable for backflow protection against Fluid Category 3). Maximum working pressure 16.0 bar.
'WHC1850'. White coloured, dry pressed ceramic disc. For use with water up to 85°C.
'YJ-AL2O3 95%'. White coloured, dry pressed and sintered ceramic disc. For use with water up to 85°C.
'PRO V500 V4'. Red coloured chemical anchor resin supplied in a pre-weighed dual cartridge. Apply as per manufacturer's instructions version '9', dated 'October 2022'. Cure for 48 hours@7°C. For use with water up to 23°C. For use only as a resin anchor having been tested at a reduced surface area to volume ratio of 1,000mm² per 1 litre of water. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
‘METOLUX Metoset’. Site applied, grey coloured chemical anchor resin which is supplied in a pre-mixed cartridge. Apply as per manufacturer’s instructions 'version 2', dated 29.10.2023. Cure for 4 days@7°C. For use with water up to 23°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'J-FIX ULTRA-BOND 100 EPOXY RESIN'. Red coloured chemical anchor resin supplied in a pre-weighed dual cartridge. Apply as per manufacturer's instructions 'Re00', dated 'August 2023'. Cure for 48 hours@7°C. For use with water up to 23°C. For use only as a resin anchor having been tested at a reduced surface area to volume ratio of 1,000mm² per 1 litre of water. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
Wall mounted, metal, single outlet, fixed combination tap assemblies. Flow is controlled by a solenoid valve activated by via an infra-red sensor and temperature adjusted via a single lever operating member. The Inlets incorporate stainless steel strainers & approved check valve cartridges, however, the complete product has not been fully tested to demonstrate it provides backflow protection. The outlet incorporates a plastic aerator. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.
Non-metallic materials and components comply with BS6920 at 60°C
Range of single hole, single outlet (fixed) electronically controlled tap assemblies in (chrome plated brass bodies). Flow is controlled with a solenoid valve activated via an infra-red sensor. The temperature is controlled via a single lever operating member on the body. The inlets incorporate stainless steel strainers and approved check valve cartridges, however, the complete product has not been fully tested to demonstrate it provides backflow protection. The spout outlets incorporate a plastic aerator. Maximum working pressure 8.0 Bar
Non-metallic materials and components comply with BS6920 at 65°C
Range of single hole, single outlet (fixed) electronically controlled tap assemblies (brass bodies - various finishes). Flow is controlled via a solenoid valve activated via an infra-red sensor. The temperature is controlled manually with a single lever operating member. The spout outlet incorporates a plastic aerator. The inlets incorporate single check valve cartridges, however, the complete product has not been fully tested to demonstrate that it provides backflow protection. Maximum working pressure 8.0 Bar
Non-metallic materials and components comply with BS6920 at 65°C
Single hole, single outlet (fixed) electronically controlled tap assemblies (either black finish or chromium plated brass bodies). Flow is controlled by a solenoid valve which is actuated via an infra-red sensor. The spout incorporates a stainless-steel strainer on the outlet. The product is supplied with a stainless steel braided PEX lined flexible hose assembly and a combination valve with a DZR brass body consisting of a servicing valve, a single check valve cartridge, verified by test (suitable for backflow protection against Fluid Category 2), a stainless-steel strainer and plastic flow regulator on the outlet. The combination valve has a compression inlet for use with copper pipe (manufactured to BS EN 1057). The tap incorporates a soap dispenser with a separate dispensing nozzle. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.
Wall mounted, single hole, single outlet (fixed) electronically controlled tap assemblies (either black finish or chromium plated brass bodies). Flow is controlled by a solenoid valve which is actuated via an infra-red sensor. The spout incorporates a stainless-steel strainer on the outlet. The product is supplied with a stainless steel braided PEX lined flexible hose assembly and a combination valve with a DZR brass body consisting of a servicing valve, a single check valve cartridge, verified by test (suitable for backflow protection against Fluid Category 2), a stainless-steel strainer and plastic flow regulator on the outlet. The combination valve has a compression inlet for use with copper pipe (manufactured to BS EN 1057). The tap incorporates a soap dispenser with a separate dispensing nozzle. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.
Range of wall mounted, single hole, single outlet (fixed) electronically controlled tap assemblies comprising of a concealed brass body and a separate spout and trim set (chromium plated brass). Flow is controlled by a solenoid valve activated via an infra-red sensor. The inlets (within the) concealed body incorporate a plastic filter and an approved check valve cartridge, however, the complete product has not been fully tested to demonstrate it provides backflow protection. The spout outlet incorporates a plastic aerator. Maximum working pressure 5 bar. Maximum operating temperature 60°C
Range of floor mounted, single-hole, single outlet (fixed), combination tap assemblies (chromium plated brass bodies), incorporating a ceramic cartridge headwork with a single lever operating member and a manual diverter to shower outlet. The spout outlet incorporates a plastic aerator. The product is supplied with a shower hose and handset. Maximum working pressure 5 bar. Maximum operating temperature 85°C
Range of spring-loaded resilient trim in-line check valve cartridges with acetal bodies. For insertion into specifically dimensioned bores. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Range of spring loaded resilient trim check valve cartridges with a plastic body and EPDM ‘O’-rings. For insertion into specifically dimensioned bores Maximum working pressure 10 Bar Maximum operating temperature 85°C
Range of in-line single check valve assemblies consisting of a spring loaded resilient trim check valve cartridge housed within a DZR brass body. For use with copper pipe manufactured to EN1057. Maximum working pressure 10.0 bar. Model 12.10322.015.CP5R-8511 has a maximum operating temperature of 65°C. Model 12.10322.022.CP5R-8511 has a maximum operating temperature of 85°C.
In-line non-verifiable single check valve assembly consisting of a single check valve cartridge housed within a DZR brass body. Maximum working pressure 16.0 bar. Cold water use only.
Verifiable double check valve assembly consisting of two spring loaded resilient trim in-line check valve cartridges housed in a DZR brass body with two test ports. Maximum working pressure 10.0 bar. Maximum operating temperature 85°C.
Double check valve assembly consisting of two spring loaded resilient trim in-line check valve cartridges housed in a DZR brass body (plated?) with isolation valve & Strainer. Maximum working pressure 10 bar. Maximum operating temperature 85°C
Double check valve assembly consisting of two spring loaded resilient trim check valve cartridges housed in a nickel plated DZR brass body. The product also incorporates a lever operated isolation valve. For use with copper tube to BS EN 1057. Maximum working pressure 10 Bar Maximum operating temperature 85°C.
Single hole, single outlet (fixed) over the rim (swivel nozzle) bidet combination tap assembly (chromium plated brass), incorporating a ceramic cartridge headwork with a single lever operating member. The spout outlet incorporates a plastic aerator. The product is supplied with a lever type operated pop-up waste. Maximum working pressure 10.0 Bar Maximum operating temperature 60.0°C
Single hole, single outlet (fixed), over the rim (swivel nozzle) bidet combination tap assembly (chromium plated brass), incorporating a ceramic cartridge headwork and single lever operating member. The spout outlet incorporates a plastic aerator and product is supplied with lever type pop-up waste. Maximum working pressure 10.0 Bar. Maximum operating temperature 60.0°C.
Range of single hole, single outlet (fixed) over the rim (swivel nozzle) bidet combination tap assemblies (brass body, various finishes), incorporating ceramic cartridge headworks with single lever operating members. The spout outlet incorporates a plastic aerator. The product is supplied with a lever type pop-up waste. Maximum working pressure: 10.0 Bar. Maximum operating temperature: 60.0°C.
Single hole, single outlet (fixed) over the rim (swivel nozzle) bidet combination tap assembly with a brass body (Chromium plated brass) incorporating a ceramic cartridge headwork with single lever operating member. The spout outlet incorporates a plastic aerator. The product is supplied with a lever operated pop-up waste. Maximum working pressure 10.0 Bar. Maximum operating temperature 60.0°C.
Single hole, single outlet (fixed) over the rim swivel nozzle bidet combination tap assembly (brass body - various finishes) with a ceramic cartridge headwork and single lever operating member. The spout outlet incorporates a plastic flow straightener. The product is supplied with a lever operated pop-up waste (not verified by test). Maximum working pressure 5.0 Bar. Maximum operating temperature 60.0°C.
Single hole, single outlet (fixed), over the rim (swivel nozzle) bidet combination tap assembly (brass bodies - various finishes), incorporating a ceramic cartridge headwork with a single lever operating member. The spout outlet incorporates a plastic aerator. The product is supplied with a lever operated pop-up waste (not verified by test). Maximum operating pressure 10.0 bar. Maximum operating temperature 60°C.
Range of single hole, single outlet (fixed), over the rim (swivel nozzle) bidet combination tap assemblies (brass bodies - various finishes), incorporating a ceramic cartridge headworks with single lever operating members. The spout outlets incorporate plastic aerators. The product is supplied with a lever operated pop-up waste (not verified by test). Maximum operating pressure 10.0 bar. Maximum operating temperature 60°C.
Single hole, single outlet, swivel bidet combination tap assembly (chromium plated brass), with a ceramic cartridge headwork and single lever operating member. The spout outlet has a plastic aerator. Product is supplied with lever type pop-up waste. Maximum operating pressure 10.0 bar. Maximum operating temperature 60°C.
Ceramic cartridge headwork with a plastic body, incorporating EPDM ‘O’-rings. The product is intended for insertion into specifically dimensioned tap assemblies. Maximum working pressure 10 Bar. Maximum operating temperature 65°C.
Ceramic cartridge headwork with a plastic body and EPDM gaskets and seal rings. For insertion into specifically dimensioned bores Maximum working pressure 10 bar. Maximum operating temperature 85°C
Range of ceramic cartridge headworks and ceramic disc diverter headworks with plastic bodies, EPDM and/or silicone seals. Maximum working pressure 10.0 bar. Maximum operating temperature 85°C.
Thermostatic cartridge with NBR ‘O’-rings for insertion into specifically dimensioned bores. Maximum working pressure 12.0 bar. Maximum operating temperature 85°C.
Range of thermostatic cartridges with either plastic or brass bodies (see model) and stainless-steel filters (except model ZL-FX-LFXTS45). For insertion into specifically dimensioned bores. Maximum working pressure 6.0 bar. Maximum operating temperature 75°C.
Single hole, single outlet (swivel) combination tap assemblies with (brass bodies -various finishes) incorporating ceramic cartridge headworks with single lever operating members. The spout outlet incorporates a plastic aerator and a pull out spray. The connection between the outlet and the hose incorporates an approved single check valve cartridge, however, the complete product has not been fully tested to demonstrate that it provides backflow protection. Maximum working pressure 10.0 Bar Maximum operating temperature 65.0°C
Single hole, single outlet, pull-out spray combination tap assemblies incorporating brass body (two finishes) and a ceramic cartridge headwork with single lever operating member. The pull-out spray spout outlets swivel and incorporate a plastic aerator. The inlet to the tap and the spout outlet incorporate a single check valve cartridge however, the complete product has not been fully tested to demonstrate it provides backflow protection. Maximum working pressure 3.0 bar. Maximum operating temperature 60°C
Single hole, single outlet (swivel) combination tap assembly (chromium plated brass), incorporating a ceramic cartridge headwork with a single lever operating member. The spout is a pull-out spray type incorporating a push button and plastic aerator. The connection to the pull-out hose incorporates an approved single check valve cartridge, however, the whole product has not been fully tested to demonstrate that it provides backflow protection. Maximum working pressure 5.0 Bar. Non-metallic materials and components comply with BS6920 at 65°C
Range of single hole, single outlet (swivel) combination tap assemblies with (brass bodies -various finishes) incorporating ceramic cartridge headworks with single lever operating members. The spout outlet incorporates a plastic aerator.and a pull out spray feature. The connection between the outlet and the hose incorporates an approved single check valve cartridge, however, the complete product has not been fully tested to demonstrate that it provides backflow protection Maximum working pressure 7 bar. Maximum operating temperature 65ºC.
Single hole single outlet (swivel) pull down spray combination tap assemblies (brass bodies – various finishes) incorporating a ceramic cartridge headworks and single lever operating members. The spout outlet incorporates a plastic aerator. Maximum working pressure 10.0 bar. Maximum operating temperature 65°C.
Single hole, single outlet (swivel) combination tap assemblies with (brass bodies -various finishes) incorporating ceramic cartridge headworks with single lever operating members. The spout outlet incorporates a plastic aerator and a pull out spray. The connection between the outlet and the hose incorporates an approved single check valve cartridge, however, the complete product has not been fully tested to demonstrate that it provides backflow protection. Maximum working pressure 10.0 Bar Maximum operating temperature 65.0°C
Range of single hole, single outlet (swivel) combination tap assemblies (brass bodies, various finishes - see model), incorporating a ceramic cartridge headwork with a single lever operating member. The products incorporate a pull-out spout with a plastic aerator. Both models incorporate an approved check valve cartridge within the quick connector to the pull-out hose, and the inlet to the pull-out spout of the 63036-01X model incorporates an approved check valve cartridge with a plastic flow regulator, however, the complete product has not been fully tested to demonstrate it provides backflow protection. Maximum working pressure 5.0 bar. Maximum operating temperature 60°C.
Range of single hole, single outlet (fixed) combination tap assemblies (brass bodies - various finishes), incorporating a ceramic cartridge headwork with single lever operating members. The spout outlets of F9406M and F9406M-** incorporate a plastic aerator. F8122B, F8122B-**: Maximum working pressure - 5.0 Bar. Maximum operating temperature 85°C. F9406M, F9406M-**: Maximum working pressure - 10.0 Bar.Maximum operating temperature 65.0°C
Range of single hole, single outlet, fixed combination tap assemblies, (chromium plated brass bodies) incorporating ceramic cartridge headworks with single lever operating members. The spout outlets incorporate plastic aerator. The products are supplied with a lever type pop-up waste. Maximum working pressure 10.0 Bar. Maximum operating temperature 60.0°C.
Range of single hole, single outlet (fixed) combination tap assembly (chromium plated brass) incorporating ceramic cartridge headwork with single lever operating members. The spout outlet incorporates a plastic aerator. Some of the products are supplied with a click type pop-up waste, verified by test. Maximum working pressure 10.0 Bar. Maximum operating temperature 60.0°C.
Range of single hole, single outlet (fixed) combination tap assemblies (chromium plated brass) incorporating a ceramic cartridge headwork (27216L & 28216L models) or a pressure balancing ceramic cartridge headwork (27216LEP & 28216LEP models), both with a single lever operating member. The spout outlet incorporates a plastic flow straightener. The inlets include an adaptor and a separate isolation valve. The 27216L & 28216L models are also supplied with a brass adaptor housing a plastic strainer and a plastic flow restrictor, (for installation between the isolation valve and inlet tails). The 27216LEP & 28216LEP models are also supplied with a DZR brass adaptor housing a plastic strainer, a plastic flow restrictor and a single check valve cartridge, verified by test (suitable for backflow prevention against Fluid Category 2), (for installation between the isolation valve and inlet tails). Maximum working pressure 5.0 bar. Maximum operating temperature 60°C.
Range of single hole, single outlet (fixed) combination tap assemblies (brass bodies - various finishes), incorporating ceramic cartridge headworks, with single lever operating members. The spout outlet incorporates a plastic aerator. Maximum working pressure 10 bar. Maximum operating temperature 65°C
Range of single-hole, single outlet (fixed) combination tap assemblies (brass bodies, various finishes - see model), incorporating a ceramic cartridge headwork with a dome type operating member (CPH0321K/V and CPH0326K/V models) or a single lever operating member (all other models). The spout outlet incorporates a plastic aerator. Maximum working pressure 16.0 bar. Maximum operating temperature 65°C.
Range of single hole, single outlet (fixed) combination tap assemblies (brass bodies - various finishes), incorporating a ceramic cartridge headwork with single lever operating members. The spout outlets of all models except TAP031 incorporate a plastic aerator. TAP031L Maximum working pressure - 5.0 Bar. Maximum operating temperature 85°C. All other models Maximum working pressure - 10.0 Bar. Maximum operating temperature 65.0°C
Page 37 of 56
We use cookies to give you the best possible experience with WRAS. Some are essential to provide website functions and ensure the website is secure. We also use cookies to help us understand how people use the site and to make improvements. Click "Accept All" to enable recommended settings or click "Manage cookies" to adjust your settings. For more details, see our Cookie Policy.
