Electrolytic scale inhibitors incorporating copper or nickel coated copper bodies. Compression models are to be used with copper pipe manufactured to BS EN1057. Maximum working pressure 10.0 bar. Cold water use only.
'Sheraplex Blue, Black, Green & Silver'. Factory applied, organic resin coating system, consisting of a primer and 'Delta Seal' topcoat (available in blue, black, green and silver colours). Apply one coat of primer (as per instructions: WI.BMC.W02 Issue 2 - February 2005) and cure for 2 and ½ hours at 380°C. Then apply a passivation layer through immersion for 15 minutes at 76-99°C (as per instructions: WI.BMC.W06 Issue 1 August 2004). Apply 1 topcoat of 'Delta Seal' (as per instructions WI.BMC.W01A Issue 2 August 2010) and cure for 20 minutes at 200°C. All are for use with water up to 23°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
‘FIBER TECH 82’. Factory applied, natural (appears dark yellow) fibreglass resin. Spray apply as per manufacturer’s Method Statement Ref ‘PP-GRP-092021-R1’, dated ‘21 Sept 2020’. Cure for 72 hours@25°C. For use with water up to 40°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'JM 9-2910'. Factory applied, blue coloured epoxy powder coating. Apply as per manufacturer's instructions 'edition no.1', issue date 2012-8-5. Cure for 15 minutes@180°C. For use with water up to 85°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'HEMPADUR 85671 System'. Factory applied epoxy coating system comprising of a pink base coat (50900), light green middle coat (42070), and pink top coat (50900 - water contact). Each coat comprises of a base and curing agent to be mixed in a 8.8:1.2 volume ratio before applying in accordance with manufacturer's PDS dated January 2023. Cure each coat for 7 days@20°C and then 20 hours@40°C. For use with water up to 30°C.
'Interline 925P Light Grey & Interline 925P Off White'. Site applied, two component epoxy coatings. Mix Parts A & B in a volume ratio of 3:1 and apply as per manufacturer's datasheet '10257', issue date '07/02/2022'. Cure for 7 days@25°C. For use with water up to 60°C. These materials are only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the materials are not covered by the scope of the approval.
‘MoyaProof WS2’. Site applied, grey coloured (once mixed), two-component, polymer modified Portland cement based cementitious waterproofing membrane. Mix Part A (white, opaque liquid) with Part B (grey, opaque powder) in a 1:4 mass ratio and apply two coats as per manufacturer’s Technical Datasheet ‘CC/MP05/Ver09/01/21’. Cure Coat 1 for 2 hours at 5˚C. Cure Coat 2 for 28 days at 5˚C. For use with water up to 23°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Rotormagnet 12-0000294'. Dark grey coloured, injection moulded Polyamide + Strontium Ferrite magnet. For use with water up to 60°C.
'15.0903.01 & 15.0902.01'. Dark grey coloured, ferrite anisotropic magnets (commonly known as ceramic magnets). For use with water up to 85°C.
'ForTii Ace WX51-FC BK00001, ForTii PA Xgea20 BK28049 & PA Xgea BK28049'. Black coloured, injection moulded PA 4T materials. For use with water up to 85°C.
‘Zytel® FG70G30HSR2 BK309’. Black coloured, injection moulded polyamide material. For use with water up to 23°C. From January 2024, the material is for use with water up to 60°C.
'Fusamatic Electrofusion Fittings'. Black coloured, injection moulded, polyethylene Electrofusion Fittings (made in UK from Ineos Eltex TUB121 & Hostalen CRP 100 Resist CR Black). In December 2023, Electrofusion Fittings made in Anhui Province China from Borouge Borsafe HE3490-LS & Hostalen CRP 100 Resist CR black were added to the approval. For use with water up to 60°C.
'Fusamatic Electrofusion and Spigot Fittings'. Black coloured, injection moulded, polyethylene Electrofusion and Spigot Fittings (made from Ineos Eltex TUB121, Hostalen CRP 100 Resist CR Black & Borouge Borsafe HE3490-LS). For use with water up to 60°C.
'Fusamatic Electrofusion and Spigot Fittings'. Black coloured, injection moulded, polyethylene Electrofusion and Spigot Fittings (made from Ineos Eltex TUB121, Hostalen CRP 100 Resist CR Black & Borouge Borsafe HE3490-LS). For use with water up to 60°C.
‘HELUPOWER® AQUATIC-750-BLUE’. Extruded, blue coloured cable with polyethylene sheath (water contact layer), available with between 1 and 5 metallic cores and a wall thickness of between 1.2mm & 5.9mm. For use with water up to 23°C.
'571983 & 571984'. White coloured (semi-translucent), extruded PTFE tape. For use with water up to 85°C.
'Venda Tapafugas Blinker'. Site applied, off-white coloured, fibre glass impregnated, polyurethane repair tape. Apply as per manufacturer's technical data sheet '01-02-29R R4'. Cure for 30 minutes@23°C. For use with water up to 23°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'07148-70' components. Black coloured, compression moulded EPDM components with a shore hardness of 70. Sealing gaskets have an in-radius size of 1.0mm. Sealing membranes have an in-radius size of 0.92mm. Gasket membranes have an in-radius size of 0.85mm. Membrane seals have an in-radius size of 1.0mm. Sealing rings have an in-radius size of 1.0mm. For use with water up to 85°C.
'ITK349601'. Black coloured, injection moulded EPDM C-seals. Shore hardness 70. Tested in-radius size 1.0mm. For use with water up to 85°C.
'EP90/4 BLK Seals and 'O' rings'. Black coloured, injection moulded EPDM seals and 'O' rings. Shore hardness 90. The seals have a tested in-radius size of 1.7mm. The 'O' rings have a tested in-radius size of 1.2mm. For use with water up to 85°C.
'CS-EW70'. Black coloured, compression moulded EPDM rubber. Shore hardness 70. Tested in-radius size 0.96mm. For use with water up to 23°C.
'EPDM 773'. Black coloured, injection moulded EPDM sheet material (manufactured in Czech Republic). Shore hardness 50. Tested in radius sizes 0.9mm. For use with water up to 23°C.
'EPDM 798'. Black coloured, injection moulded EPDM material (manufactured in Czech Republic). Shore hardness 60. Tested in-radius size 1.0mm. For use with water up to 23°C.
'Sunaflex T 8193'. Black coloured, compression moulded EPDM rubber material. Shore hardness 80. Tested in-radius size 1.0mm. For use with water up to 23°C.
'AquaFlex T 5893'. Black coloured, compression moulded EPDM material. Shore hardness 80. Tested in-radius size 1.0mm. For use with water up to 65°C.
'AquaFlex T 9696'. Black coloured, compression moulded EPDM material. Shore hardness 70. Tested in-radius size 1.0mm. For use with water up to 85°C.
'01/E90FKM Gaskets & 'O' rings'. Black coloured, injection moulded FKM gaskets & 'O' rings. Shore hardness 90. The gaskets have an in-radius size of 1.1mm and the 'O' rings have an in-radius size of 1.0mm. For use with water up to 85°C.
'ELASTOSIL LR 3020/60 A+B' Natural (appears white, translucent) & 'ELASTOSIL LR 3020/60 A+B with 2% by weight ELASTOSIL Colour Paste FL Red Iron Oxide RAL 3013' (red coloured). Injection moulded silicone rubbers with a shore hardness of 60 ShA and a tested in-radius size of 0.9mm. For use with water up to 85°C.
'Supercast PVC Waterstop Hydrofoil'. Blue coloured, extruded PVC waterstop. For use with water up to 23°C. These materials are for use in concrete reservoirs and similar structures, constructed in accordance with the design criteria of BS EN 1992 with respect to normal frequency of joints. The materials have been tested at a reduced surface area to volume ratio of 1000mm² per litre as specified in BS 6920: Part 1
'GFS Gas Flex Systems 543 Pipe Sealants'. Blue coloured pipe sealant. Apply as per manufacturer's TDS '01/09/2022 v1.0'. Cure for 24 hours@23°C. For use with water up to 85°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
Bidet seat assembly which discharges via a push button actuated solenoid valve and utilises a ‘Type AB’ air gap arrangement (verified by test - suitable for backflow prevention against Fluid Category 5). Maximum working pressure 8 bar. Maximum operating temperature 40°C
Single hole, triple outlet (swivel) combination tap assembly (brass bodies, various finishes - see model), incorporating a ceramic cartridge headwork with single lever operating member. Electronic controls allow the tap to dispense boiling, chilled or sparkling water. The vented models are supplied with a brass adaptor containing a plastic flow regulator and a combined EPDM washer and stainless-steel strainer, for installation on the mains cold water into the ceramic cartridge. They are also supplied with a stainless steel braided PEX lined flexible hose assembly and a stainless steel braided TPSiV lined flexible hose assembly both with ½” captive nut end connections for installation between the tap and a command centre, (which is not included as part of this approval). Maximum working pressure 5.0 bar. Maximum operating temperatures: Near boiling water circuit: 100°C. Ambient hot and cold (mixed) circuit: 65°C. Chilled/Chilled and sparkling circuit: Cold water use only.
Range of single hole, single outlet, electronic touch free, deck mounted taps (chromium plated brass) for cold or premixed water. Flow is controlled via solenoid valves, actuated by infra-red sensors. Power is supplied by externally mounted 9V battery pack or 9V transformer. The inlet hoses have a stainless-steel strainer and the spout outlets incorporate plastic aerators. Maximum working pressure 8.0 bar.
Non-metallic materials and components comply with BS6920 at 65°C
Range of wall mounted, single-hole, single outlet (fixed) electronically controlled combination tap assemblies (chrome plated brass or stainless-steel bodies) which are supplied with pre-mixed water. Flow is controlled via an infra-red activated solenoid valve and the spout outlets incorporate plastic aerators. Maximum working pressure 8.0 bar
Non-metallic materials and components comply with BS6920 at 65°C
Range of single hole, single outlet, fixed, electronically controlled tap assemblies (chrome plated brass bodies). Flow is controlled via an infra-red activated solenoid valve and the spout outlets incorporate plastic aerators. The inlets incorporate a stainless-steel filter washer. Maximum working pressure 8.0 bar
Non-metallic materials and components comply with BS6920 at 65°C
Range of single hole, single outlet (fixed) electronically controlled tap assemblies (various finishes - see model). Flow is controlled by a solenoid valve activated by via an infra-red sensor. The TK-201LT66 and TK-201LT95 models have a multi-layer PEX lined hose between the solenoid and the spout. The TK-201LT65 models have a stainless steel braided PEX lined flexible hose between the solenoid and the spout. The spout outlet incorporates a plastic aerator. Maximum working pressure 8.0 bar. Maximum operating temperature 60°C.
Range of aerator kits incorporating plastic flow regulators (1.9l/min, 3.5l/min & 5.0l/min) with plastic bodies and EPDM ‘O’ rings. Plastic adaptors, NBR washers and chromium plated brass housings may also be supplied as part of the kit. Maximum operating temperature 65°C.
Deck mounted side valve (brass body) incorporating a quarter turn ceramic disc headwork and cross top operating member. Maximum working pressure 10.0 Bar.
Non-metallic materials and components comply with BS6920 at 60°C
Range of single hole, single outlet (fixed) combination tap assemblies (brass bodies – various finishes) incorporating ceramic cartridge headworks with single lever operating members. The spout outlets incorporate plastic aerators. Maximum working pressure: See Models
Non-metallic materials and components comply with BS6920 at 60°C
Range of single hole, single outlet (fixed) combination tap assemblies with brass bodies (black or chrome plated), incorporating ceramic cartridge headwork and single lever operating member. Spout outlet incorporates a plastic aerator. Maximum working pressure 5- 10.0 bar (see models). Maximum operating temperature 60°C – 85°C (see models).
Range of single hole, single outlet (fixed) combination tap assemblies (chromium plated brass bodies), incorporating a ceramic cartridge headwork and single lever operating members. The spout outlet is a waterfall type. The products are supplied with a click type pop-up waste. Maximum working pressure 5.0 bar. Maximum operating temperature 85ºC.
Range of single hole, single outlet, fixed combination tap assembly, (chrome plated brass bodies) incorporating ceramic cartridge headworks with single lever operating members. The spout outlets incorporate aerators and plastic flow straighteners. The products are supplied with a click type pop-up waste. Maximum working pressure 16 bar. Maximum operating temperature 60°C
Range of wall mounted, single hole, single outlet (fixed) combination tap assemblies (brass bodies - various finishes), incorporating ceramic cartridge headworks with single lever operating members. The spout outlets incorporate plastic aerators. Maximum working pressure 10 bar. Maximum operating temperature 65°C
Range of single hole, single outlet (fixed) combination tap assemblies ( brass bodies - various finishes), incorporating either a ceramic cartridge or ceramic disc (see models) headworks with either a single lever or cross top (see models) operating member. The spout outlet incorporates either a plastic aerator, a plastic flow straightener or an open outlet type spout (see models). Some models are supplied with a click type waste and some are supplied with a lever type pop-up waste (see models). Maximum working pressure 5.0 Bar or 10.0 Bar (see models) Maximum operating temperature 65.0°C or 85.0°C (see models)
Range of single hole, single outlet (swivel) combination tap assemblies (brass bodies - various finishes). Incorporating a quarter turn ceramic disc headworks with spring loaded return to the closed position controlling flow of the boiling water outlet and a ceramic cartridge headwork controlling flow from the hot and cold supply with dome type or lever type operating members (model V7C294 does not incorporate a ceramic cartridge headwork, for boiling water only). Maximum working pressure 5.0 Bar
Non-metallic materials and components comply with BS6920 at 85°C
Range of single hole, single outlet, swivel combination tap assemblies (brass bodies, various finishes - see model), incorporating a ceramic cartridge headwork with a single lever operating member. The vented models are supplied with a stainless steel braided PEX lined flexible hose assembly incorporating a ½" captive nut end connection, which provides main cold water to a venturi device which is part of a command centre (not supplied). The Arc vented models are supplied with a DZR brass tee piece, two DZR brass adaptors, two stainless-steel strainers (each combined with an EPDM washer) and a plastic flow restrictor, for installation prior to the cold inlet hose. The Arc and Cube mains models are supplied with two DZR brass adaptors and two stainless-steel strainers (each combined with an EPDM washer), for installation on each inlet hose. The spout outlet incorporates a plastic aerator. Maximum working pressure 5.0 bar.
Non-metallic materials and components comply with BS6920 at 65°C
Range of single hole, single outlet, (swivel) combination tap assembly (chrome plated brass bodies) incorporating ceramic cartridge headworks with single lever operating members. The spout outlet incorporates a plastic aerator. Maximum working pressure 10 bar. Maximum operating temperature 60°C.
Range of two hole, single outlet (fixed), combination tap assemblies with (brass bodies - various finishes) incorporating quarter turn ceramic disc headworks with single lever or dome type operating members (see models). The spout outlet of model F4195** incorporates a plastic aerator. The products are supplied with metal back nuts. Maximum working pressure 10.0 bar.
Non-metallic materials and components comply with BS6920 at 65°C
Range of two hole, single outlet (fixed) combination tap assemblies (brass bodies – various finishes), incorporating quarter turn ceramic disc headworks and single lever operating members. The spout outlets for models (143106) incorporate plastic flow straighteners or a plastic aerator ,models (M33146E &153306) incorporate plastic flow straighteners & model (172306) incorporates a plastic aerator. The products are supplied with metal backnuts. Maximum working pressure 10 bar. Maximum operating temperature 85°C for models 179606F, 173606, 173606 MBK1, M33146E. Maximum working pressure 10 bar. Maximum operating temperature 65°C 143106, 153306, 172306
Deck mounted two-hole, single outlet (fixed) combination tap assembly (chromium plated brass) with a self-cancelling diverter to a shower outlet. The product incorporates a ¼ turn ceramic disc headwork and single lever operating members. The spout outlet incorporates a plastic aerator. The products are supplied with metal backnuts, stainless steel braided PVC lined shower hose and chromium plated shower handset. Maximum operating pressure 5 bar. Maximum operating temperature 60°C
Non-metallic materials and components comply with BS6920 at 60°C
Page 36 of 89
We use cookies to give you the best possible experience with WRAS. Some are essential to provide website functions and ensure the website is secure. We also use cookies to help us understand how people use the site and to make improvements. Click "Accept All" to enable recommended settings or click "Manage cookies" to adjust your settings. For more details, see our Cookie Policy.
