A screwdriver operated spherical ball valve with brass body, chromium plated brass ball and EPDM O-ring. Maximum working pressure 5.5 bar. Maximum operating temperature 85oC.
Range of spherical valves incorporating a chrome plated brass body & brass ball. Maximum operating pressure 10 bar. Maximum operating temperature 65 °C.
Albion SLP series of normally open and normally closed solenoid valves with brass bodies. Maximum working pressures SLP**EE* models 12.0 bar, SLP**EE*H models 8.0 bar. Maximum operating temperature 70°C.
Range of Instantor lever action ball valves with brass bodies, chromium plated brass balls and PTFE seats. Maximum working pressure 25 bar. Maximum operating temperature 85°C
Range of spherical valves with stainless steel bodies, PTFE seats and silicone O-rings. Maximum working pressure 10.0 bar. Maximum operating temperature 90°C.
Range of spherical valves with PVC-U or ABS bodies and ball (see models).. PVC-U models with a solvent weld pipe connection are for use with PVC-U pipe (manufactured to ISO 1452) and are supplied with a PVC-U solvent cement. ABS models with a solvent weld pipe connection are for use with ABS pipe (manufactured to ISO 15493) and are supplied with an ABS solvent cement. Maximum working pressure 16.0 Bar. Cold water use only.
Range of gate valves with blue epoxy coated ductile iron bodies and hand wheel operating members. Maximum working pressure 25.0 bar (DN50-DN300) or 10.0 bar (DN400 only) Maximum operating temperature 85ºC
Range of angled stop valves, (chromium plated brass bodies) with dome operating members. Maximum working pressure 5.0 bar. Maximum operating temperature 85°C
Range of screw down stop valves with plastic bodies for below ground use.. The valves are supplied with loose pipe inserts and are for use with polyethylene pipe (manufactured to BS EN 12201). Maximum working pressure 14.0 bar. Cold water use only.
Range of electromagnetic scale inhibitors with stainless steel bodies. Maximum working pressure: 16.0 bar. Cold water use only.
Range of UV disinfection units with stainless steel bodies. Maximum working pressure 10.0 bar. Maximum operating temperature 35°C.
'KOCETAL® K100BK & KOCETAL® K300BK'. 'KOCETAL® K500BK’ was added to the approval in June 2025. Black coloured, injection moulded POM materials. For use with water up to 23°C.
‘KOCETAL® WR301 (white coloured) & KOCETAL® WR301 BK (black coloured)’. Injection moulded POM materials. For use with water up to 23°C.
'CELCON F10-01 T2, F10-02, F10-03H, F20-03M, F25-03 & F30-03M'. The following grades were added to the approval in April 2023: ‘CELCON F30-34, F10-01, F10-03HM, F20-03, F25-03M & F30-03’. Natural, unpigmented (white in appearance), injection moulded POM materials. All the grades listed can be coloured using the following masterbatch CELCON MB-S315F (black coloured masterbatch). All are for use with water up to 85°C.
'FORMOCON FM130'. White coloured, injection moulded POM material. For use with water up to 85°C.
'J1200 (RBSIC) & J1300 (SSIC)'. Grey coloured, compression moulded and sintered, Silicon carbide mechanical sealing rings. For use with water up to 85°C.
'H/E16018'. Factory applied, dark blue coloured electrostatic enamel coating. Apply as per manufacturer's TDS '00', dated '30.08.2017' and cure for 4.5 minutes at a peek temperature of 850°C. For use with water up to 85°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'KOROGUARD 20 RED & GREY'. Factory applied, two-component epoxy coatings available in red and grey. Mix parts A & B in a 3:1 volume ratio and apply as per manufacturer's TDS dated 'Jan 2024'. Cure for 7 days@30°C. For use with water up to 23°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Chosui Coat Grey'. Factory applied, grey coloured (once mixed and applied), two-component epoxy resin coating, Mix base:hardener in a 2:1 weight ratio and apply as per PDS 'CN：IF438122003', dated '03/06/2022'. Cure for 7 days@30°C and then 7 days@60°C. For use with water up to 60°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Epigard Solvent Free Epoxy Finish'. Factory applied, two-component, red coloured epoxy coating. Mix base & accelerator in a volume ratio of 3:1 and apply as per user instructions dated '20th Dec 2024'. Cure for 24 hours@30°C. For use with water up to 23°C. This material is only approved for the curing and mixing conditions that appear on the approval. If the cure/mix conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'DZT PANT I1000-NC; DZT PANT I10G05-NC; DZT PANT I10G10-NC; DZT PANT I10G15-NC; DZT PANT I10G20-NC; DZT PANT I10G25-NC; DZT PANT I10G30-NC; DZT PANT I10G35-NC; DZT PANT I10G40-NC; DZT PANT I10G45-NC; DZT PANT I10G50-NC; DZT PANT I10G55-NC; DZT PANT I10G60-NC; DZT PANT I10G65-NC (un-pigmented - appears beige)’. ‘DZT PANT I10G05-BK; DZT PANT I10G10-BK; DZT PANT I10G15-BK;DZT PANT I10G20-BK;DZT PANT I10G25-BK; DZT PANT I10G30-BK; DZT PANT I10G35-BK;DZT PANT I10G40-BK;DZT PANT I10G45-BK; DZT PANT I10G50-BK; DZT PANT I10G55-BK; DZT PANT I10G60-BK; DZT PANT I10G65-BK (black coloured)'. Injection moulded PA materials. For use with water up to 85°C.
'KN133G30 (off-white in colour) & KN133G15BL (black coloured)'. Injection moulded PA6 materials. KN133G30 is for use with water up to 65°C. KN133G15BL is for use with water up to 23°C.
'Revolve N-307 (5056) Natural'. Natural (appears white), rotationally moulded PE material. For use with water up to 85°C.
'DIC.PPS Z-230-T5 BLACK'. Black coloured, injection moulded PPS material. For use with water up to 85°C.
'Verplen C3008 VE ACLKUV W (GF 30% green coloured) & Verplen 60NE A W (black coloured'. Injection moulded, polypropylene materials. For use with water up to 60°C.
'51M6630'. Black coloured, injection moulded EPDM material. Shore hardness 70A. Tested in-radius size 1.0mm. For use with water up to 70°C.
‘Permabond A011 Red, A025 Orange, A113 Blue, A115 Orange, A118 Green, A130 Blue, A131 White, A134 Green, A136 Red, A140 Green, A1042 Blue, A1044 White, A1058 Off White, F200 Brown, F201 Brown, F202 Brown, A1084 Yellow & F201HV (translucent)’. Anaerobic adhesives to be applied and cured in strict accordance with the manufacturer's instructions. For use with water up to 85°C.
Range of wall mounted, two-hole, single outlet (fixed) electronically controlled tap assemblies (chromium plated brass). The flow is controlled by a solenoid valve activated via infra-red sensor. Temperature is controlled independently via a thermostatic cartridge with a dome operating member which incorporates a manual override button. The spout outlets incorporate plastic aerators, and both inlets incorporate an approved single check valve cartridge (however, the complete assembly has not been fully tested to demonstrate that it provides adequate backflow protection) and stainless-steel strainers. Maximum working pressure 10.0 Bar. Maximum operating temperature 60.0°C.
Range of electronic combination tap assemblies, incorporating a solenoid valve controlling the flow that is activated via an infra-red sensor. The Xeris models (012930699 & 012940699) incorporate a check valve cartridge in the inlet hose, however the complete assembly has not been tested to demonstrate it provides backflow protection. Maximum working pressure 10 bar. Maximum operating temperature 60°C.
Range of CA-b backflow prevention devices with plastic bodies, incorporating EPDM seals and diaphragm. Maximum working pressure 3.0 bar. Maximum operating temperature 65°C.
Range of CAb backflow prevention devices with plastic bodies, incorporating EPDM seals and diaphragm. Filling link with manual or automatic tap. Maximum working pressure 3.0 bar. Maximum operating temperature 65°C.
Range of flow straighteners with plastic bodies. The JM030503-15 model incorporates a silicone lined flexible hose with an interlocked metal outer. The JM030002-15 model incorporates a swivel ball joint. Both models incorporate a stainless steel mesh on the outlet. Maximum operating temperature 60°C.
Range of ceramic cartridge headworks with a plastic body. Maximum working pressure 10.0 bar. Maximum operating temperature 85°C.
Range of ceramic cartridge headworks with plastic bodies for insertion into specifically dimensioned tap assemblies. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Ceramic cartridge headwork with a plastic body and EPDM seals, for insertion into specifically dimensioned tap assemblies. Maximum working pressure 16.0 Bar. Maximum operating temperature 80°C
Range of single hole, single outlet (fixed) combination tap assemblies, (brass bodies – various finishes). Incorporating a ceramic cartridge headworks with single lever operating members. The spout outlets incorporate plastic aerators. Maximum working pressure 5.0 Bar Maximum operating temperature 60.0°C
Range of single hole, single outlet fixed combination tap assemblies (brass body with various finishes), incorporating a ceramic cartridge headwork with either a single lever or cross top operating member. The spout outlets incorporate a plastic aerator. Products are supplied with PEX inner-lined grey plastic braided inlet hoses. Maximum working pressure 10 bar.
Non-metallic materials and components comply with BS6920 at 60°C
Single hole, single outlet (fixed) combination tap assemblies (chrome plated brass body) incorporating a ceramic cartridge headwork with various operating members. The spout outlets incorporate a plastic aerator. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.
Range of single-hole, single outlet (fixed) combination tap assemblies (brass bodies - various finishes) incorporating a ceramic cartridge headwork with single lever operating members. The spout outlets incorporate plastic aerators. Maximum working pressure 8.0 bar. Maximum operating temperature 60°C.
Range of floor-standing single hole, single outlet (fixed) combination tap assemblies (various finishes), incorporating a ceramic cartridge headworks with single lever operating members and a self-cancelling diverter to shower outlet. The spout outlet incorporates a plastic aerator. The product is supplied with shower hose and handset. Maximum working pressure 3.5 bar. Maximum operating temperature 60°C
Range of single hole, single outlet (swivel) combination tap assemblies (brass bodies – various finishes). Incorporating a ceramic cartridge headwork and single lever operating member. The spout outlet incorporates a plastic aerator. Maximum working pressure 5.5 bar. Maximum operating temperature 60°C
Range of wall mounted three-hole, single outlet (fixed) combination tap assemblies with brass bodies (various finishes). Incorporating quarter turn ceramic disc headworks and various operating members. The spout outlet incorporates a plastic aerator. Maximum working pressure 3.5 bar. Maximum operating temperature 60°C
Range of wall mounted, three-hole, single outlet (fixed) combination tap assemblies (brass bodies – various finishes), incorporating quarter turn ceramic disc headworks with single lever operating members. The spout outlets incorporate plastic aerators. Maximum working pressure 8.0 Bar. Maximum operating temperature 60°C
‘MUFA’ and ‘MUPA’ ranges of expansion vessels with epoxy coated bodies. ‘MUFA’ models have a maximum working pressure of 8.6 bar. ‘MUPA’ models have a maximum working pressure of 10.0 Bar. Cold water use only.
Range of in-line carbon block water filters and housings with polypropylene bodies. Maximum working pressure 8.0 bar. Cold water use only.
Range of copper press fittings with EPDM ‘O’-rings for use with EN1057 copper tube. The joints are achieved by means of a press tool. For above and below ground use (sizes 12mm-54mm only. 66.7mm, 76.1mm, 88.9mm & 108mm for above ground use only) Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Range of PCC type press copper crimp fittings with EPDM ‘O’-rings for use with copper tube manufactured to EN 1057. The joints are achieved by means of a crimping tool. For above ground use. Maximum working pressure: 16.0 bar. Maximum operating temperature: 85°C
Range of CU type press copper crimp fittings with EPDM ‘O’-rings for use with copper tube manufactured to EN 1057. The joints are achieved by means of a crimping tool. For above ground use. Maximum working pressure: 16.0 bar. Maximum operating temperature: 85°C
Range of press fittings (brass bodies - various finishes) with stainless steel press (Unipress MLCP ) collars and EPDM O-rings for use with “EA” range of PEX/AL/PEX multilayer pipe (for press fitting connections and compression for EHA adaptor fittings only) or copper pipe manufactured to EN1057 (compression connections). Maximum operating temperature: 95°C. Maximum operating pressure: 10 bar.
Range of stainless steel press fittings to be used with stainless steel pipes. Connection is achieved via M profile press jaws. For above ground and below ground use. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Page 35 of 43
We use cookies to give you the best possible experience with WRAS. Some are essential to provide website functions and ensure the website is secure. We also use cookies to help us understand how people use the site and to make improvements. Click "Accept All" to enable recommended settings or click "Manage cookies" to adjust your settings. For more details, see our Cookie Policy.
