Range of gate valves with DZR brass bodies, stems and discs. The valves operate via a hand wheel (non-rising) and a metal to metal seal. Valves are for above ground use only. Maximum working pressure 16.0 Bar. Maximum operating temperature 85.0°C.
Range of ductile iron gate valves with blue epoxy coated bodies, EPDM wedges and EPDM O-rings. Maximum working pressure 25.0 Bar. Maximum operating temperature 85.0°C
Range of gate valves with blue epoxy ductile iron bodies and wedges incorporating PTFE seals and a non-rising spindle (16Q models) or outside screw and yoke (125Q models). The valves incorporate a handwheel operating member. Maximum working pressure 16.0 Bar Maximum operating temperature 85.0°C
Range of non-rising spindle gate valves with bronze, brass or DZR brass (MV40-1116) bodies, incorporating hand wheel or key operated operating members. Maximum working pressure 16.0 Bar (MV40-1153) 25.0 bar
Non-metallic materials and components comply with BS6920 at 85°C
Range of IVR 605 gate valve with brass bodies, PTFE or NBR packing. The valves operate via a non-rising spindle headwork with hand wheel operating members. Maximum working pressure 16.0 bar. Maximum operating temperature 23°C.
Range of motorised position pilot operated control valves with epoxy coated ductile iron bodies and stainless-steel pipework and fittings. Maximum operating pressure 16.0 bar. Maximum operating temperature 65°C.
Range of commercial washing machines with flow controlled by solenoid valves and discharged via type AB air gap assembly (verified by test - suitable for backflow protection against fluid category 5). The inlets incorporate approved check valve cartridges, however, the complete product has not been fully tested to demonstrate it provides backflow protection Maximum working pressure 5 Bar. Maximum operating temperature 60°C.
ClearScale Plus range of in-line water conditioners with stainless steel bodies and catalytic alloy core. Maximum working pressure 16.0 bar. Maximum operating temperature 100°C.
Range of ultraviolet disinfection units with stainless-steel bodies. Maximum working pressure 10.0 bar. Maximum operating temperature 40°C.
'ABS Dev1236 White'. White coloured, injection moulded ABS material. For use with water up to 60°C.
'ELECTROCOAT BP 1119'. Factory applied, black coloured Bituminous Paint. Apply as per manufacturer's TDS Document No: 'ECL/ TDS / BP-1119-Bituminous Paint', Issue Date '10-Aug-20', Version No: '01'. Cure for 12 minutes at 45°C, followed by 10 hours at 28°C. For use with water up to 65°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'JERLAC Bituminous sealer coat black'. Factory applied, black coloured Bitumen coating. Apply as per manufacturer's TDS reference 'BN433', dated '27/07/2023', revision '00'. Cure for 12 hours@30°C. For use with water up to 60°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'LUBERPOX-2K-DS-LACKFARBE (IV81 & IW81)’ – blue coloured and ‘LUBERPOX-2K-DS-LACKFARBE (IV81812 & IW81)’ – red coloured’. Factory applied, two component, epoxy coatings consisting of IV81 or IV81812 (base) and IW81 (hardener). Mix IV81 or IV81812 (base) & IW81 (hardener) in a mass ratio of 5:1 or volume ratio of 3.5:1 and apply as per manufacturer’s data sheets ‘Rev: 04 – 04.12.2023’ (blue) or ‘Rev: 03 – 04.12.2023’ (red). Cure for 20 minutes@22°C and then 40 minutes@75°C. For use with water up to 65°C. These materials are only approved for the mixing and curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the materials are not covered by the scope of the approval.
'KAJ1207'. Factory applied, blue coloured epoxy coating. Apply as per manufacturer's instructions 'file no. I01-KAJ1207' dated '2019.1.14'. Cure for 15 minutes@200°C. For use with water up to 85°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'JERLAC Solventless Epoxy Grey'. Factory applied, grey coloured, two-component Epoxy coating. Mix Base:Curing Agent in a 2:1 volume ratio and apply as per manufacturer's TDS reference 'BN434', dated '24/07/2023', revision '01/03.12.2025'. Cure for 7 days@30°C. For use with water up to 85°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
‘Sikadur-Combiflex® SG System’ comprising of ‘Sikadur® 31 DW’ epoxy adhesive to be used in conjunction with ‘Sika Combiflex® SG Membrane’. ‘Sikadur® 31 DW’ is a site applied, grey coloured, two-part epoxy adhesive consisting of Part A (white coloured) and Part B (black coloured). Part A and Part B are mixed in a weight ratio of 3:1, applied and cured for 14 days@30°C. ‘Sika Combiflex® SG Membrane’ is a modified flexible Polyolefin (FPO) waterproofing tape to be applied over the adhesive and is approved as the water contact layer. Apply as per ‘Sikadur-Combiflex® SG System’ System Product Data Sheet, ‘Edition: 24/10/2012, Identification no: 02 07 03 02 System, Version: GCC’. For use with water up to 50°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
‘Sika Monotop 1010’ primer for use with ‘Sika Monotop 4012’ cement mortar. Site applied, grey coloured cementitious, polymer modified coating material used as bonding primer and cementitious, fibre reinforced, low shrinkage repair mortar. First coat: Mix 25kg ‘Sika Monotop 1010’ with 5.25 litres of water and apply as per manufacturer’s ‘Sika Monotop 4012' IFU issue no. ‘001’ dated ‘July 2022’. Second coat: Mix 25kg ‘Sika Monotop 4012’ with 3.8 litres of water and apply immediately to the first coat as per manufacturer’s IFU issue no. ‘001’ dated ‘July 2022’. Cure for 21 days@7°C. For use with water up to 23°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
‘4TECH 9S20000 W-A-ABK 01 0A QF, 4TECH 9S22130 W-A-ABK, 4TECH 9S22110 W-A-ABK & 4TECH 9S22120 W-A-ABK’. Black coloured, injection moulded PPO & PPO/HIPS materials. 4TECH 9S20000 W-A-ABK 01 0A QF is an unfilled PPO material suitable for use with water up to 23°C. 4TECH 9S22130 W-A-ABK, 4TECH 9S22110 W-A-ABK & 4TECH 9S22120 W-A-ABK are filled PPO/HIPS materials suitable for use with water up to 85°C.
'Xarec WA212, WA210 & WA552'. Injection moulded, glass fibre reinforced, syndiotactic polystyrene sheet materials which are available in natural (appears cream) or black. For use with water up to 85°C.
'MXLOC 12638, 38 & 48'. Green coloured acrylic based adhesives. Apply as per manufacturer`s instructions. For use with water up to 23°C.
MXLOC acrylic based adhesives. Apply as per manufacturer`s instructions. Grades for use with water up to 23°C. MXLOC 22 (purple coloured), 11243, 70, & 90 (green coloured). MXLOC 42 & 43 (blue coloured). MXLOC 542 (brown coloured). MXLOC 12638, 38 & 48 (green coloured). MXLOC 71 & MXBON 11271 (red coloured). Grade for use with water up to 85°C. MXLOC 13577, 577 & MXBON 13577 (yellow coloured).
'GIRPI HTA Fusion'. Site applied, orange coloured solvent cement, intended to join plastic pipe and fittings. Apply as per manufacturer instructions '6311289/20'. Cure for 24 hours@7°C. For use with water up to 70°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
Range of single hole, single outlet (fixed) electronically controlled tap assemblies, (Chrome plated - brass bodies). Flow is controlled by a solenoid valve activated by via an infra-red sensor. The spout outlets incorporate plastic aerators. Maximum working pressure 10 bar. Maximum operating temperature 60°C.
Range of wall mounted, electronically operated combination tap assembly (chrome plated brass body). The flow is controlled by a solenoid valve which is actuated via an infrared sensor. The spout outlets incorporate a plastic aerator. The solenoid valve inlet incorporates a plastic and stainless steel filter. The products are supplied with a triple layered connecting hose (PVC inner and outer layer and nylon braided middle layer). Maximum working pressure 8.0 bar.
Non-metallic materials and components comply with BS6920 at 60°C
Side entry BS1212-4 fill valves with a plastic body. Maximum working pressure 10.0 bar. Coldwater use only.
Range of side or bottom entry BS1212-4 (2016) compact type float operated valve for WC flushing cisterns. The inlet incorporates a flow regulator. Maximum working pressure 10.0 bar. Cold water use only.
Range of BS1212-4 (2016) float operated valves for WC flushing cisterns, bottom or side entry type with plastic or brass ½’’ BSP inlet. The inlet incorporates a strainer, Compact models incorporate a delay fill function. Maximum working pressure 10.0 bar. For use with cold water only.
Range of concealed WC dual flushing cisterns with a vertical BS 1212-4(2016) float operated inlet valve providing a Type AG air gap arrangement and a dual flush outlet valve. The flush volume is operated by a two-push button assembly. The product also incorporates a servicing valve and flexible hose on the inlet supply. Maximum working pressure 10 Bar, cold water use only.
Range of spring loaded resilient trim check valve cartridges with a plastic body and EPDM ‘O’-rings. For insertion into specifically dimensioned bores Maximum working pressure 10 Bar Maximum operating temperature 85°C
Range of non-verifiable double check valve assemblies consisting of two spring loaded resilient trim in-line check valve cartridges housed in DZR brass bodies. Maximum working pressure 16.0 bar Maximum operating temperature 85°C
Range of single hole, single outlet (fixed), over the rim (swivel nozzle) bidet combination tap assemblies (brass bodies - various finishes), incorporating a ceramic cartridge headworks with single lever operating members. The spout outlets incorporate plastic aerators. The product is supplied with a lever operated pop-up waste (not verified by test). Maximum operating pressure 10.0 bar. Maximum operating temperature 60°C.
Range of quarter turn ceramic disc headworks with brass bodies and EPDM O rings. For insertion into specifically dimensioned bores. Maximum working pressure 5.0 bar. Maximum operating temperature 60°C.
Single hole single outlet (swivel) pull down spray combination tap assemblies (brass bodies – various finishes) incorporating a ceramic cartridge headworks and single lever operating members. The spout outlet incorporates a plastic aerator. Maximum working pressure 10.0 bar. Maximum operating temperature 65°C.
Range of deck mounted single hole, single outlet (fixed) combination tap assemblies (chromium plated brass). Incorporating ceramic cartridge headwork, and single lever operating member. The spout outlet incorporates a plastic flow straightener and supplied with a flow regulator. Model 23.112 is supplied with a lever type pop-up waste (not tested). Maximum working pressure 10 bar. Maximum working temperature 60°C
Range of single hole, single outlet (fixed) combination tap assemblies (chromium plated brass bodies), incorporating a ceramic cartridge headwork with a single lever operating member. The spout outlet incorporates a plastic aerator. Maximum working pressure 10.0 Bar. Maximum operating temperature 65°C.
Range of single-hole, single outlet (fixed) combination tap assemblies (brass bodies - various finishes) incorporating ceramic cartridge headwork with single lever operating members. The spout outlets incorporate a plastic flow straightener. Model (V108-XX) is supplied with a lever operated pop-up waste. Maximum working pressure: 5.0 Bar. Maximum operating temperature 85°C.
Description Greenstart 4000 Combi DHW Pre-heat kit, Preheat accessory assembly for connection to the domestic hot water circuit of a combination boiler max working pressure 10 bar max operating temperature 82℃
Range of single hole, single outlet (swivel) combination tap assemblies (brass body with various finishes) incorporating a ceramic headwork cartridge with a single lever operating member. The spout outlets incorporate a plastic aerator. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.
Range of wall mounted, two-hole, single outlet (fixed) combination tap assemblies (brass body - various finishes). Incorporating a thermostatic cartridge controlling the temperature with dome operating members that incorporate a manual override button, and a quarter turn ceramic disc headworks controlling the flow with dome type operating members. The spout incorporates a lockable diverter to shower outlet and a plastic flow straightener. The inlets incorporate approved check valve cartridges, however, the complete product has not been fully tested to demonstrate it provides backflow protection. Maximum working pressure 8 Bar Maximum operating temperature 60°C
Range of filter housings with plastic bodies. Maximum working pressure 12.0 bar. Cold water use only.
Inoxpres range of stainless-steel crimp fittings with EPDM ‘O’-rings and gasket for use with Inoxpres stainless-steel tube (1.4404 AISI 316L or 1.4521 AISI 444 – annealed or not-annealed). The connection is created by using a pressing tool. For above and below ground use. Maximum working pressure: 16.0 bar. Maximum operating temperature: 95°C.
Instantor Metric Copper Press Range crimp fittings with EPDM ‘O’-rings for use with copper tube manufactured to EN 1057. The joints are achieved by means of a crimping tool. For above ground use. Maximum working pressure: 16.0 bar. Maximum operating temperature: 85°C
Press (TH press profile) and screw/compression fittings with brass bodies for use with Comisa Evo Pipe (PE-RT/AL/PE), for above ground use only. Maximum working pressure 10.0 bar. Maximum operating temperature 99°C.
Range of press copper crimp fittings with EPDM ‘O’-rings for use with copper tube manufactured to EN 1057. The joints are achieved by means of a crimping tool. For above ground use. Maximum working pressure: 16.0 bar. Maximum operating temperature: 85°C
Range of AIS tin-plated brass and PPSU press fit fittings for use with MULTIPIPE multi layered PE-RT/AL/PE-RT pipe. Maximum working pressure 10.0 bar. Maximum operating temperature 70°C.
Range of MULTITUBO tin-plated brass and PPSU press fit fittings for use with MULTITUBO multi layered PE-RT/AL/PE-RT pipe. Maximum working pressure 10.0 bar. Maximum operating temperature 70°C.
Range of ‘NiroSan’ stainless-steel crimped fittings incorporating EPDM ‘O’ Rings, for use with ‘NiroSan’, ‘NiroSan SF’ & ‘NiroSan -ECO’ stainless-steel pipe (all manufactured to EN10312). The fittings and pipe are assembled using a crimping tool with either ‘M’ (15-108mm), ‘V’ (15-54mm) or ‘SA’ (15-108mm) crimping profiles. For above ground use only. Maximum working pressure: 16 Bar. Maximum operating temperature: 99°C.
“DZRCOM” range of DZR brass compression fittings for use with copper pipe (manufactured to EN 1057). The tank connectors incorporate a NBR gasket. The straight tap connectors incorporate a blue fibre gasket. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
‘Hansen easy fit’ range of polypropylene compression fittings with EPDM ‘O’-rings for use with metric PE80 (20mm-63mm) and PE100 (32mm-110mm) pipe to AS/NZS:4130 and plastic pipe inserts. For above and below ground use. Maximum working pressure: See models. Maximum operating temperature: Cold water use only.
MecFlow Press (PPSU & Brass) Ranges of press fittings for use with MecFlow Press pipes. Maximum working pressure 10.0 bar. The maximum operating temperature is 95oC.
Page 25 of 50
We use cookies to give you the best possible experience with WRAS. Some are essential to provide website functions and ensure the website is secure. We also use cookies to help us understand how people use the site and to make improvements. Click "Accept All" to enable recommended settings or click "Manage cookies" to adjust your settings. For more details, see our Cookie Policy.
