‘3600xx’ range of brass compression fittings for use with copper pipe (manufactured to EN 1057). The 360014 tank connector, 360013 and 360017 tap connectors all incorporate an EPDM washer. Maximum working pressure 10.0 bar. Maximum operating temperature 85°C.
‘CFxx’ range of brass or DZR brass compression fittings for use with copper pipe (manufactured to EN 1057). Maximum working pressure 16.0 bar. Maximum operating temperatures: CF15 and CF16 models: 65°C. All other models: 85°C.
Range of compression fittings with polypropylene bodies for use with PE100 pipe (manufactured to EN 12201). Some of the female adaptors (55920-9-L, 55920-10-L, 55920-11-L & 55920-11-M), female threaded elbows (56935-10-L, 56935-11-L & 56935-11-M) have a maximum working pressure of 10.0 bar. All other models have a maximum working pressure of 16.0 bar. For above and below ground, cold water use.
'PlumbRight' range of push-fit fittings with PEX-b, polysulphone or PPE bodies, supplied with polysulphone inserts. For use with PEX pipe (manufactured to BSEN 7291 part 3), PB (manufactured to BSEN 7291 part 2) and copper pipe. Maximum working pressure 12.5 bar. Cold water use only.
“D-“ and “E-“ range of 304 and 316L stainless steel press fittings, in either ‘M’ press profile (D- prefix models) or ‘V’ press profile (E- prefix models) for use with stainless steel pipe (316L & 304 manufactured to EN10312). For above ground use only. Maximum working pressure 16.0 bar. Maximum operating temperature: 85°C.
Dual flush, WC outlet valves for either full or reduced flush. Incorporates an internal overflow. Cold water use only.
Range of pre-assembled hydraulic blocks incorporating plate heat exchangers, pressure relief valves set at 3.0 bar, circulation pumps and flow regulators. Maximum working pressure: Primary 2.5bar & secondary 10 bar. Maximum operating temperature 80°C (CH) & 60°C (DHW).
Range of floor-standing gas combination boilers, supplied with isolation valves, expansion vessel and a pressure relief valve set at 3.0 bar. Maximum working pressure: Primary circuit 2.5 bar, secondary 10 bar. Maximum operating temperature: Primary 82°C / secondary circuit 60°C.
Range of water meters with brass bodies. The inlet incorporates a plastic strainer. Maximum working pressure 16.0 bar. Maximum operating temperature is 50°C or 85°C, please refer to model.
An in-line ultra-sonic water meter with brass (WM15) or plastic (SM15) bodies. Maximum working pressure: 16 Bar. Maximum operating temperature: 50°C (WM15) or 70°C (SM15).
Range of water meters with plastic bodies and plastic turbines. The inlet incorporates a plastic strainer. Maximum working pressure 16.0 bar. Maximum operating temperature 50°C.
Range of in-line water meters incorporating bronze copper alloy bodies and EPDM O rings. Maximum working pressure 10.0 Bar Maximum operating temperature 30.0°C
Compact wall outlet elbow with brass body (various finishes). Maximum operating temperature 85.0°C Open outlet use only
Range of flow sensors incorporating either brass, plastic or stainless steel bodies & EPDM ‘O’-rings. Maximum working pressure 10.0 bar for models VVXA, VVXC, VVXB. Maximum working pressure 16.0 bar for models VVXD & VVXE. Maximum operating temperature 90°C.
Range of EPDM expansion joints with flanged end conenctors. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Range of electromagnetic flow meters with carbon steel bodies, NBR inner liner and stainless-steel electrodes. Maximum working pressure 16.0 bar. Maximum operating temperature 80°C.
Range of multistage centrifugal pumps with stainless-steel housings, stainless-steel impellers and EPDM ‘O’-rings. Maximum working pressure 10.0 bar. Maximum operating temperature 85°C.
Range of pumps, with stainless steel bodies, impellers and shaft. Maximum working pressure 10.0 bar. Cold water use only.
Range of wall mounted angled overhead showers, consisting of stainless-steel bodies (various finishes) and silicone nozzles. The inlets are fitted with plastic flow limiters. Maximum operating temperature 65⁰C. Open outlet use only.
Range of overhead shower outlets. The inlet incorporates a stainless-steel filter washer. Maximum operating temperature 65°C.
Range of PVC lined flexible shower hoses with a black or silver finish. Open outlet use only. Maximum operating temperature 60°C.
Range of flanged `Y` patterned in-line strainers with blue, black or red epoxy coated ductile iron bodies, stainless steel mesh. Maximum working pressure 16 Bar. Maximum operating temperature 85°C.
Range of in-line `Y`-patterned strainers with bronze bodies incorporating stainless steel mesh strainers and PTFE washers. Maximum working pressure 20.0 bar. Maximum operating temperature 85°C.
Range of in-line `Y`-patterned strainers with bronze bodies incorporating stainless steel mesh strainers and PTFE washers. Maximum working pressure 20.0 bar. Maximum operating temperature 85°C.
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| 936L | Chrome | G3/4, male | 10 bar | 60 °C | WRAS, XINYA | BODY | No | 1/4 Turn ceramic disk | Metal Backnuts | Aerator | |
| 932L | Chrome | G1/2, male | 10 bar | 60 °C | WRAS, XINYA | BODY | No | 1/4 Turn ceramic disk | Metal Backnuts | Aerator |
Pillar taps (chromium plated brass) with quarter turn ceramic disc headworks and cross top operating members. The spout outlet incorporates a plastic flow straightener. The product is supplied with plastic back nuts. Maximum working pressure 10.0 bar. Maximum operating temperature 65°C.
Pillar taps (chromium plated brass) with quarter turn ceramic disc headworks and cross top operating members. The spout outlet incorporates a plastic flow straightener. The product is supplied with plastic back nuts. Maximum working pressure 10.0 bar. Maximum operating temperature 65°C.
Self closing basin tap (chromium plated brass) with spring loaded headwork and dome type operating members. The spout outlets incorporate a plastic flow straightener and the products are supplied with metal backnuts. Maximum working pressure 10.0 bar, Maximum operating temperature 85°C.
FLEXCORE range of stainless steel and polyamide braided flexible polyethylene lined hose assemblies with various end connections. For use with copper pipe to EN1057 Maximum working pressure:10 bar Maximum operating temperature:70°C
Range of EVOX stainless steel or grey nylon braided polyethylene lined flexible hose assemblies incorporating EPDM ‘O’-rings with various end connections. Maximum working pressure 10.0 bar. Maximum operating temperature 70°C.
‘KM1001 series’ of stainless steel braided EPDM lined flexible hose assemblies. Compression end connections are for use with copper pipes (manufactured to EN 1057). Compression end connections are also available with brass bodied (nickel plated) isolation valves incorporating a chrome plated brass ball. Maximum working pressure 10.0 bar. Maximum operating temperature 85°C.
Range of stainless-steel braided, EPDM lined flexible hose assemblies. Maximum working pressure 10.0 bar. Maximum operating temperature: 60°C.
Range of air venting valves with a blue epoxy coated ductile iron body, plastic float, EPDM ‘O’-rings and seals. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Range of wall mounted thermostatic blending valves with chrome plated brass bodies and ceramic disc headwork with a dome type operating member. Temperature is controlled independently via a thermostatic cartridge also with a dome type operating member. Inlets incorporate single check valve cartridges however, the complete assembly has not been tested to demonstrate it provides adequate backflow protection. The products are supplied with a shower hose and handset. Maximum working pressure 10.0 Bar Maximum operating temperature 60.0°C
Range of wall mounted thermostatic shower valves with brass bodies (chromium plated) incorporating a ceramic disc controlling the flow to the shower (for some models it diverts the flow to a hand shower or overhead shower) using a dome type operating member. The temperature is controlled independently via a thermostatic cartridge with a dome type operating member incorporating a manual override button. Inlets incorporate stainless steel strainers and an approved single check valve cartridge; however, the complete product has not been fully tested to demonstrate it provides backflow protection. Maximum operating pressure 5.0 bar. Maximum operating temperature 50°C
Range of butterfly valves incorporating blue or green epoxy coated ductile iron bodies, discs and EPDM seals. Maximum working pressure 16.0 Bar Maximum operating temperature 65.0°C
Range of wafer or lugged butterfly valves incorporating blue epoxy coated ductile iron bodies, EPDM seats and stainless-steel discs. The LTDX71X-16Q DN40-150 size models are lever operated; all other models and sizes are gear operated. Maximum working pressure 10.0 bar or 16.0 bar. Maximum operating temperature 100°C.
Range of wafer, lugged and flanged butterfly valves with blue, black or red epoxy coated ductile iron bodies, zinc coated (galvanised) discs and EPDM seats. F700L & F703L models incorporate a hand wheel operating members and F700G & F703G incorporate a worm gear operating member. Maximum working pressure 16.0 bar. Maximum operating temperature 70°C.
Range of butterfly valves incorporating blue epoxy coated ductile iron bodies, stainless-steel discs and EPDM seats. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Range of butterfly valves with blue epoxy coated ductile iron bodies and discs. The valves incorporate a hand wheel operating member. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Combined pre-set temperature and pressure relief valves (set at 7.0 bar) incorporating DZR brass body. The compression connection to be used with copper pipe BS EN 1057. Maximum working pressure 7.0 bar. Maximum operating temperature 95°C.
Combined pre-set temperature and pressure relief valves (set at 7.0 bar) incorporating DZR brass body. The compression connection to be used with copper pipe BS EN 1057. Maximum working pressure 7.0 bar. Maximum operating temperature 95°C.
Range of in-line pilot operated level control valves with blue epoxy coated ductile iron bodies. The products have flow control facility controlled via a float operated valve and are supplied with auxiliary components including stainless steel pipe & fittings, spherical valves, bleed valve and a needle valve. Maximum working pressure 16.0 Bar. Maximum operating temperature 60.0°C.
Range of inline pilot operated altitude control valves with blue epoxy coated ductile iron bodies and bonnets. The pilot system consists of spherical valves, in line strainers, needle valve, non-return valve, altitude gauge and a pre-set altitude control valve. The spring rating of the pilot 10-60ft (3 to 18m). Maximum working pressure 16.0 Bar Maximum operating temperature 60.0°C
Range of double swing gate, wafer, non-return valves with blue, black or red epoxy coated ductile iron bodies. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Range of swing gate, non-return valves with (blue, black or red epoxy powder coated) ductile iron bodies. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
A range of non-return valve with blue epoxy coated ductile iron bodies, stainless-steel disc and EPDM seats. Maximum working pressure 16.0 Bar Maximum operating temperature 85.0°C
Range of adjustable, pilot operated pressure reducing control valves with ductile iron bodies (blue epoxy coated). The products are supplied with auxiliary stainless-steel tubing, fittings, strainer, spherical valve and DZR pilot valve, DZR electrically actuated spherical valve. Maximum inlet supply pressure 16.0 bar. Maximum outlet pressure between 2.0 bar – 12.5 bar. Maximum operating temperature 80°C.
Range of pilot operated pressure relief control valves with blue epoxy coated ductile iron bodies and supplied with auxiliary components including stainless steel pipe & fittings, spherical valves, bleed valve and a needle valve. Spring ratings of pilot valve are 0.35 - 3.5 bar, 0.7 - 5.5bar, 1.38 - 13.8 bar, 6.9 - 20.7 bar Maximum working pressure 16.0 Bar Maximum operating temperature 60.0°C
Range of spherical valves with nickel plated brass bodies and a chrome plated ball. The handle can either be a flat lever handle or a T handle (See models) Maximum working pressure 25.0, 30.0, 40.0, 50.0 Bar Maximum operating temperature 60.0°C
Page 202 of 204
We use cookies to give you the best possible experience with WRAS. Some are essential to provide website functions and ensure the website is secure. We also use cookies to help us understand how people use the site and to make improvements. Click "Accept All" to enable recommended settings or click "Manage cookies" to adjust your settings. For more details, see our Cookie Policy.
