Range of shower handsets and shower heads with plastic bodies (chrome plated, except for the DS1200W and DS3200W models which are white) and NBR gaskets.
Non-metallic materials and components comply with BS6920 at 65°C
Range of PVC or EPDM lined shower hoses with stainless steel outer (chrome or black finish) or PVC reinforced (chrome plated finish) outer layer. Maximum operating temperature 65°C.
Range of stainless steel braided PEX lined flexible hose assembly with various end connections (see model). Maximum working pressure 10.0 bar.
Non-metallic materials and components comply with BS6920 at 70°C
Range of stainless-steel braided EPDM lined flexible hose assemblies with various end connections. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Range of stainless-steel braided EPDM lined flexible hose assemblies with various end connections. Maximum working pressure 10.0 bar.
Non-metallic materials and components comply with BS6920 at 85°C
Range of interlocked shower hoses with EPDM seals and various finishes.
Non-metallic materials and components comply with BS6920 at 70°C
Range of Direct & Indirect stainless steel insulated unvented hot water storage cylinders with internal expansion. The secondary circuit consists of a temperature and pressure relief valve set at 10.0 bar and 90°C and an alternative temperature and pressure relief valve also set at 10.0 bar and 90°C , an inlet control group consisting of a pressure reducing valve pre-set at 3.0 bar, an expansion relief valve set at 8.0 bar, a strainer and a check valve cartridge, verified by test (suitable for backflow protection against Fluid Category 2) also supplied with a tundish. Maximum working pressure - Primary circuit: 6.0 bar & Secondary circuit: 7.5 bar Maximum operating temperature 85.0°C
Range of wall mounted, concealed, thermostatic shower mixers with brass bodies, dome or cube operating members and a thermostatic cartridge controlling the temperature. Models D1001, LB091, LB092, LB093, LB094, LB095, D2002, LB096, LB097, LB098, LB099, LB100, D3001, LB101, LB102, LB103, LB104 & LB105 incorporate approved check valve cartridges; however, the complete product has not been fully tested to demonstrate it provides backflow protection. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C
Range of wall mounted, bar type thermostatic blending valves incorporating a quarter turn ceramic disc headwork or half turn ceramic diverter controlling the flow between outlets. The temperature is controlled by a thermostatic cartridge with various type of operating members incorporating a manual override button. Maximum working pressure 10 bar. Maximum operating temperature 60°C.
Wall mounted bar type thermostatic shower mixer (chromium plated brass), incorporating a quarter turn ceramic disc headwork controlling the flow with a dome type operating member. The temperature is controlled independently via a thermostatic cartridge with a dome type operating member and a manual override button. Both inlets incorporate an approved check valve cartridge, however, the complete products have not been fully tested to demonstrate they provide backflow protection. Maximum working pressure 10.0 bar.
Non-metallic materials and components comply with BS6920 at 60°C
Range of wall mounted, bar type thermostatic blending valves (chromium plated brass) incorporating a 2-way manual diverter valve controlling and diverting the flow between an overhead shower and a shower outlet with dome type operating members. The temperature is controlled independently via a thermostatic cartridge with a dome type operating member incorporating a manual override button. Inlets incorporate approved check valve cartridges, however, the complete product has not been fully tested to demonstrate it provides backflow protection. Maximum working pressure 10.0 bar. Maximum operating temperature 65°C
Range of wall mounted, concealed thermostatic blending valves or exposed bar type thermostatic blending valves (chromium plated brass) incorporating a 2-way manual diverter valve controlling and diverting the flow between an overhead shower and a shower outlet with dome type operating members. The temperature is controlled independently via a thermostatic cartridge with a dome type operating member incorporating a manual override button incorporate. An approved check valve cartridge is also supplied, however, the complete product has not been fully tested to demonstrate it provides backflow protection. The products are supplied with a shower head, shower hose and handset. Maximum working pressure 10.0 bar. Maximum operating temperature 65°C (F4017x & F2167x models. All other models 60°C only).
Range of wall mounted thermostatic blending valves (chrome plated brass), incorporating a quarter turn ceramic disc, half turn ceramic disc or ceramic cartridge headworks (see models). The temperature is controlled independently via a thermostatic cartridge incorporating a manual override button, with a variety of operating members. The inlets incorporate approved check valve cartridges; however, the complete product has not been fully tested to demonstrate it provides backflow protection with stainless-steel strainers. Maximum working pressure 5.0 Bar.
Non-metallic materials and components comply with BS6920 at 60°C
Wall mounted, bar type thermostatic blending valves with brass bodies (various finishes see models) incorporating a quarter turn ceramic disc for diverting between shower handset and overhead shower and a thermostatic cartridge controlling the temperature with a manual override button, both with dome type operating members. The product is supplied with an overhead shower head, shower hose and handset. Each inlet incorporates an approved check valve cartridge, however, the complete product has not been fully tested to demonstrate it provides backflow protection and stainless steel strainers. Maximum working pressure 10.0 bar.
Non-metallic materials and components comply with BS6920 at 60°C
Range of butterfly valves with blue epoxy coated ductile iron bodies with stainless steel and an EPDM seat. Sizes DN50-DN150 are lever operated. Sizes DN200-300 are gearbox operated. Maximum working pressure 25.0 bar.
Non-metallic materials and components comply with BS6920 at 85°C
Range of butterfly valves with blue epoxy coated ductile iron bodies and stainless-steel disc, incorporating EPDM seats. Models DN200, 250, 300, 350 and 400 have a hand wheel operating member. DN50, 65, 80, 100, 125 and 150 have lever operating member. Maximum working pressure 16.0 bar.
Non-metallic materials and components comply with BS6920 at 60°C
Range of manually operated flow control valves with stainless steel (DN80 – DN150) or epoxy coated ductile iron bodies (DN200 – DN400). Maximum working pressure 10.0 to 40.0 bar, please refer to model. Cold water use only. From April 2023 the products have a maximum operating temperature of 65°C.
Range of spherical valves with brass (K65281, K65282, K65283, K65301, K65302, K65303, K65291, K65292, K65293, K65311, K65312 & K65313) or DZR brass (K64783, K64784, K64793, K64794, K64763, K64764, K64773, K64774) bodies (chrome plated, nickel plated or without plating - see model), chrome plated brass ball and a range of different operating members (see model). Compression connections are for use with copper pipe (manufactured to EN 1057). Maximum working pressure 10.0 bar. Maximum operating temperature 85°C.
Range of quarter turn, lever handle or butterfly operated spherical valves with nickel plated brass bodies, chrome plated brass balls and PTFE seals. For use with copper pipe BS EN 1057. Maximum working pressure 25.0 bar. Maximum operating temperature 85°C.
Range of full bore spherical valves with single lever, lockable lever or butterfly operating members, nickel plate brass bodies and chrome plated, brass ball, PTFE seats and NBR O-rings.
Range of spherical valves with nickel plated brass bodies, chromium plated brass balls, PTFE seals, NBR and/or FKM ‘O’-rings. incorporates a stainless-steel strainer. Also incorporate a magnet. Maximum working pressure: See PN in brackets under model. Maximum operating temperature: Cold water use only.
Protecta-line range of screw down stopcocks with Gunmetal body’s incorporating NBR O-rings. The stopcocks are to be used with Protecta-line PE80 multi-layer pipe manufactured to BS 8558. Maximum working pressure 12.5bar. Cold water use only.
Range of commercial, front loading washing machines with flow controlled by a solenoid valve and discharged via type AB air gap assembly (verified by test, suitable for backflow protection against fluid category 5). The inlets incorporate a stainless-steel strainer. Maximum working pressure 6 Bar Maximum operating temperature 85°C
Range of electro-magnetic water conditioners with chrome plated stainless steel bodies Compression models are for use with pipe manufactured to BS EN 1057. Maximum working pressure 10 bar. Cold water use only.
'EPICOAT 1000'. Factory applied, two-component, red coloured epoxy coating. Mix base & catalyst in a 3:1 volume ratio and apply as per user instructions 'SPL/R&D/TTD/UI/006', 'version 01', dated '03.11.2022'.. Cure for 7 days@30°C. For use with water up to 60°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'DICOAT 60EX'. Factory applied, two-component, blue coloured epoxy coating. Mix base & catalyst in a 3:1 volume ratio and apply as per user instructions 'SPL/R&D/TTD/UI/007', 'version 01', dated '03.11.2022'. Cure for 7 days@30°C. For use with water up to 23°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'EPOGUARD APC 301'. Factory applied, two-component, red coloured epoxy coating. Mix parts A & B in a 3:1 volume ratio and apply as per manufacturer's Technical Data Sheet, 'rev.01', dated April 2022. Cure for 7 days@28°C. For use with water up to 23°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'RC851 S'. Factory applied, mustard coloured (once mixed), two-component epoxy coating. Mix parts A & B in a 3:1 volume ratio and apply as per manufacturer's TDS reference 'NT-0230-UK-081222-A', dated 08/12/22. Cure for 15 hours@70°C. For use with water up to 70°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'SGPAM-CN-WB01 - Black'. Factory applied, black coloured water based coating. Apply as per manufacturer's Technical Data Sheet 'PAMPIPE-TDC-WA04'. Cure for 30 min at 50°C plus 7 days at 23°C. For use with water up to 23°C. This material is only approved for the curing conditions that appear on the approval. If the curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'CEC-GFS Enamel, Black Blue RAL5004'. Factory applied, blue/black (appears black) coloured, enamel coating. Apply as per manufacturer's instructions 'ZZ-Ins001', dated '2021.01.01'. GFS-G base glaze: dry for 15 Minutes at 200°C then fire for 12 minutes at 870ºC. GFS-S surface glaze: dry for 15 Minutes at 200°C then fire for 10 minutes at 830ºC. For use with water up to 85°C. This material is only approved for the drying and firing conditions that appear on the approval. If the drying and/or firing are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Welmortar-III'. Factory applied, grey coloured cement mortar. Mix cement, sand and water in a mass ratio of 2:3:0.85. Apply as per manufacturer's Standard Operating Procedure 'WDIPL/QA/WI/14A', revision '0', dated '01.10.2021'. Cure for 21 days at 30°C & 70% humidity. For use with water up to 65°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Pentaline 1000 Red & Pentaline 1000 Grey'. Factory applied, red and grey coloured, two component solventless epoxy coatings. Mix component A & B in a volume ratio of 3:1 and apply as per manufacturer's document number 'Chembur R&D/PI/05', issue date '03/04/2023'. Cure for 7 days@30°C. 'Pentaline 1000 Red' is for use with water up to 45°C. 'Pentaline 1000 Grey' is for use with water up to 23°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'3011 Red Epoxy Anticorrosive Coating'. Factory applied, red coloured epoxy coating. Apply as per manufacturer's instructions '004', revision date '2021.12.12' . Cure for 24 hours@23°C. For use with water up to 65°C. This material is only approved for the curing conditions that appear on the approval. If the curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'NP-TANK 500 PW'. Factory applied, white coloured (once mixed), two-component, solvent-free epoxy coating. Mix Part A (white liquid) with Part B (dark amber liquid) in a 3:1 volume ratio. Apply as per manufacturer's TDS 'Rev. 06/22'. Cure for 7 days@30°C. For use with water up to 23°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Atlac 430'. Yellow coloured, vinyl ester resin material manufactured by filament winding. For use with water up to 60°C.
'SG300'. Clear (colourless) silicone spray lubricant. Apply as per manufacturer's datasheet 'issue 1' dated January 2022. For use with water up to 85°C.
‘ULTRAMID® A218W V30 Natural-C’ (natural, appears off-white) & ‘ULTRAMID® A218W V30 Black-C’ (black coloured). Injection moulded, glass fibre reinforced PA66 materials. For use with water up to 85°C.
'Tecomid NA40 GR30 BK250 HS QW'. 'Tecomid NA40 GR35 BK250 HS QW'. 'Tecomid NA40 GR40 BK250 HS QW'. 'Tecomid NA40 GR45 BK250 HS QW'. 'Tecomid NA40 GR50 BK250 HS QW'. Black coloured, injection moulded, glass fibre reinforced (30% - 50%), PA66 materials. For use with water up to 85°C.
'P600 BL & P301E BL'. Black coloured, extruded polyethylene pipes. For use with water up to 23°C.
'LUMILOY GP2300-KA02, GP2200-KA02, GP2200K-KA02, GP2300K-KA02, GP2200-NP, GP2300-NP & GP2300K-NP'. Injection moulded cream, beige, black & brown coloured PPO materials. For use with water up to 85°C.
‘Ramofin PPH300G6BK11’. Black coloured, injection moulded, polypropylene material. For use with water up to 85°C.
‘M930F, M330F, M630F, M730F, M410F & M710F’. Beige coloured, injection moulded polyketone materials. For use with water up to 85°C.
‘Tubular’ range of wall mounted spout outlets (chromium plated brass). The flow is controlled by a solenoid valve activated via an infra-red sensor. The box assembly incorporates a solenoid valve, screwdriver operated spherical valve and the spout outlet incorporates a plastic aerator. Maximum working pressure 8.0 bar. Maximum operating temperature 65°C.
A range of deck mounted, single hole, single outlet (fixed) electronically controlled tap assemblies (chromium plated brass). The flow is controlled by a solenoid valve activated via an infra-red sensor. The temperature is controlled independently via a dome operating member. The spout outlet incorporates a plastic aerator. The inlets incorporate stainless steel strainers and single check valve cartridges (however, the complete assembly has not been fully tested to demonstrate that it provides adequate backflow protection). Maximum working pressure 5.0 Bar Maximum operating temperature 65 °C
Range of single hole, single outlet (swivel) electronically controlled tap assemblies. The flow and temperature is controlled by a ceramic cartridge headworks with single lever operating members. The flow is also controlled by a solenoid valve activated via an infra-red sensor. The spout outlet incorporates a plastic aerator. The hose inlets incorporate approved check valve cartridges, however, the complete product has not been fully tested to demonstrate it provides backflow protection Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.
Range of single hole, single outlet (fixed) electronically controlled tap assemblies (chromium plated brass). Flow is controlled by a solenoid valve activated via an infra-red sensor. The spout outlet incorporates a plastic aerator. The main body incorporates a stainless-steel strainer prior to the solenoid. Maximum working pressure 8.0 Bar.
Non-metallic materials and components comply with BS6920 at 65°C
Range of wall mounted tap assemblies for cold or premixed water with chromium plated brass bodies. Flow is controlled by a solenoid valve activated via an infra-red sensor and the spout outlets have plastic aerators. Supplied with stainless steel braided PEX lined connection hoses. Maximum working pressure 8.0 bar.
Non-metallic materials and components comply with BS6920 at 65°C
Range of single hole, single outlet, electronically controlled tap assemblies (chrome plated brass body). The flow is controlled by a solenoid valve activated via an infra-red sensor. The spout outlet incorporates a plastic aerator. Supplied with a stainless steel braided PEX lined flexible connection hose and a manual lever for controlling the temperature. Maximum working pressure 8.0 bar.
Non-metallic materials and components comply with BS6920 at 65°C
Range of deck mounted single hole, single outlet (fixed) electronically controlled tap assemblies (stainless steel for models 236303 & 236404 only or chromium plated brass for all others). Flow is controlled by a solenoid valve activated by via an infra-red sensor. The spout outlet incorporates a plastic aerator. The inlets incorporate stainless steel strainers and the products are supplied with stainless steel braided PEX line connection hoses. Maximum working pressure 8.0 Bar.
Non-metallic materials and components comply with BS6920 at 65°C
Range of single hole, single outlet (fixed) electronically controlled tap assemblies (chrome plated). Flow is controlled by a solenoid valve activated via an infra-red sensor. The product incorporates a manual temperature control operated by a single lever on the side of the body. Spout outlet incorporates plastic aerator. Maximum working pressure 10.0 bar.
Non-metallic materials and components comply with BS6920 at 60°C
Page 17 of 43
We use cookies to give you the best possible experience with WRAS. Some are essential to provide website functions and ensure the website is secure. We also use cookies to help us understand how people use the site and to make improvements. Click "Accept All" to enable recommended settings or click "Manage cookies" to adjust your settings. For more details, see our Cookie Policy.
