Range of nylon braided (DG50X model series) or stainless steel braided (DG10X model series), PEX lined flexible hose assemblies with a variety of end connections (see models for full breakdown), including EPDM washers and ‘O’-rings where applicable. Some models are supplied with screwdriver operated isolation valves (see model list). All compression and push-fit fittings are to be used with copper pipe (manufactured to EN 1057). Maximum working pressure: 16 bar. Maximum operating temperature: 85°C.
Range of stainless-steel interlocked shower hoses and shower hose extension pieces (smaller length versions) incorporating PE/EPDM and PEX inner tube materials. Available with various surface finishes and end connectors. For further details see model section. Maximum working pressure open outlet use. Maximum operating temperature 85.0°C
Range of PE lined, nylon braided (black or grey) flexible hose assemblies. The hoses are available with a variety of end connections with different finishes (see model). Maximum operating temperature 85°C. Open outlet use only.
Range of stainless steel braided, EPDM lined flexible hose assemblies. Models are available with a variety of end connections. Maximum working pressure 10.0 bar. Maximum operating temperature 85°C
Range of nylon braided (DG50E model series) or stainless steel braided (DG10E model series), EPDM lined flexible hose assemblies with a variety of end connections (see models for full breakdown), including EPDM washers and ‘O’-rings where applicable. Some models are supplied with screwdriver operated isolation valves (see model list). All compression and push-fit fittings are to be used with copper pipe (manufactured to BS EN 1057). Maximum working pressure: 16 bar. Maximum operating temperature: 85°C.
Range of indirect and direct unvented storage cylinders. The secondary circuit is factory fitted with a temperature and pressure relief valve set at 7.0 bar @ 90˚C. The product is supplied with an inlet control group (safety kit) consisting of a pressure reducing valve pre-set at 3.0 bar, strainer, an expansion relief valve set at 6.0 bar and an approved check valve cartridge (verified by test - suitable for backflow protection against Fluid Category 2). A tundish and expansion vessel are also provided. Maximum working pressures: Primary: 3.0 Bar Secondary: 5.5 Bar Solar: 3.0 bar Maximum operating temperature 90.0°C
Range of T-type thermostatic mixing valves with chrome plated DZR brass bodies and EPDM ‘O’-rings incorporating a thermostatic cartridge controlling the temperature. Each inlet incorporates a stainless steel strainer. The inlets of the 252714 and 252713 models incorporate a check valve cartridge, verified by test (suitable for backflow protection against Fluid Category 2). Maximum working pressure 10.0 bar. Maximum operating temperature of 85°C.
Range of flow control valves with epoxy coated ductile iron bodies. Auxiliary components include a needle valve, pressure reducing pilot valve and isolation valves. Maximum supply pressure 16.0 bar. Outlet pressure setting is adjustable in the range 0.6 to 1.2 bar. Maximum operating temperature 65°C.
Range of pilot operated basic valves, main body only, with epoxy coated ductile iron bodies. Maximum operating pressure 16.0 bar. Maximum operating temperature 65°C.
Range of non-return, swing gate valves with gunmetal bronze bodies. Maximum working pressure 20.0 bar.
Non-metallic materials and components comply with BS6920 at 85°C
Range of pressure relief valves with plastic bodies and EPDM diaphragms and ‘O’-rings, Factory pre-set at 3.0 bar. Maximum operating temperature 110°C.
Range of lever or butterfly operated spherical valves with brass or nickel plate bodies and ball. Maximum working pressure: Various – see model section. Maximum operating temperature 99.0°C
Range of lever operated spherical valves with DZR brass or stainless-steel bodies and ball. Models beginning with ‘GP’ and ‘GPH’ are for use with copper pipes (manufactured to EN 1057). Models beginning with ‘GPMS’ and ‘GPHS’ are for use with stainless steel (SS316L) pipe (manufactured to EN 10312). Maximum working pressure 25.0 bar. Maximum operating temperature 85°C
Range of angled valves with brass bodies (some models chrome plated). Maximum working pressure 10 bar. Maximum operating temperature 65°C
Range of motorised position pilot operated control valves with epoxy coated ductile iron bodies and stainless-steel pipework and fittings. Maximum operating pressure 16.0 bar. Maximum operating temperature 65°C.
Range of bedpan washing & disinfection machines. The flow is controlled by a solenoid valve and discharged via a type `AB` airgap (verified by test - suitable for backflow protection against fluid category 5). Maximum working pressure - See models Maximum operating temperature - 90 °C
Range of commercial washing machines with flow controlled by solenoid valves and discharged via type AB air gap assembly (verified by test - suitable for backflow protection against fluid category 5). The inlets incorporate approved check valve cartridges, however, the complete product has not been fully tested to demonstrate it provides backflow protection Maximum working pressure 5 Bar. Maximum operating temperature 60°C.
Range of ultraviolet disinfection units with stainless-steel bodies. Maximum working pressure 10.0 bar. Maximum operating temperature 40°C.
'KAJ1207'. Factory applied, blue coloured epoxy coating. Apply as per manufacturer's instructions 'file no. I01-KAJ1207' dated '2019.1.14'. Cure for 15 minutes@200°C. For use with water up to 85°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
‘Hempadur 3556K’. Factory applied, cream coloured epoxy coating consisting of a two-part primer and two-part top coat. The two-part primer is Hempadur 15590 red (56880) and this is mixed in a volume ratio of 7.93:2.14 and applied as per manufacturer's Product Data Sheet dated February 2024. Cure for 24 hours@20°C. The two-part top coat is Hempadur 3556K cream (20320) and this is mixed in a volume ratio of 6.8:2 and applied as per manufacturer's Product Data Sheet dated March 2024. Cure for 7 days@20°C. For use with water up to 35°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the materials are not covered by the scope of the approval.
'Loctite PC 7255 GN (Green) coating for use with Bonderite M-NT 1455-W primer'. Factory applied, green coloured, two-component epoxy resin coating. In June 2025 ‘LOCTITE PC 7255 GY (Grey) coating for use with BONDERITE M-NT 1455 Primer-W Coating’ was added to the approval. Factory applied, grey coloured, two-component epoxy resin coating. Prime the surface to be coated with the Bonderite primer wipe. Mix and apply as per manufacturer’s TDS dated October 2016. Cure for 7 days@23°C at 45% relative humidity. For use with water up to 85°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'ES 988 DWPU'. Site applied, two-component polyurethane coatings which are available in blue or grey colours (once mixed). Mix Part A (blue or grey opaque liquid) with Part B (amber, translucent liquid) in a 100:30.5 weight ratio and apply as per manufacturer's technical data sheet 'TDS507DWPU.rv2.17102018'. Cure for 14 days@7°C. For use with water up to 23°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the materials are not covered by the scope of the approval.
‘Sikadur-Combiflex® SG System’ comprising of ‘Sikadur® 31 DW’ epoxy adhesive to be used in conjunction with ‘Sika Combiflex® SG Membrane’. ‘Sikadur® 31 DW’ is a site applied, grey coloured, two-part epoxy adhesive consisting of Part A (white coloured) and Part B (black coloured). Part A and Part B are mixed in a weight ratio of 3:1, applied and cured for 14 days@30°C. ‘Sika Combiflex® SG Membrane’ is a modified flexible Polyolefin (FPO) waterproofing tape to be applied over the adhesive and is approved as the water contact layer. Apply as per ‘Sikadur-Combiflex® SG System’ System Product Data Sheet, ‘Edition: 24/10/2012, Identification no: 02 07 03 02 System, Version: GCC’. For use with water up to 50°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
‘Corroless ACO Brush Grades RAL5005 (GB861) and Light Green (GB206)’ (formerly known as 'Acothane Brush Grades Blue & Green'). Site applied, blue or green coloured, two-part polyurethane coatings consisting of an amber coloured, liquid activator and blue or green coloured coating. Mix brush grade and activator in a 3.24:1 weight ratio. Apply as per technical data sheet dated Feb 2020. Cure for 14 days@7°C. For use with water up to 23°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mix and cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Interline 975 White'. Site applied, two-part epoxy coating which can be applied as one coat or three coats. Mix parts A & B in a 2.2:1 and apply as per manufacturer's TDS 'Ref:4236', 'Issue Date: 04/02/2015'. When applied as a single coat, the coating must be cured for 14 days at 10°C. When applied as a three-coat system, the coating must be cured as follows: coat 1 = 24 hours@10 °C, coat 2 = 24 hours@10 °C & coat 3 = 14 days@10 °C. For use with water up to 23°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
‘Sikagard®-1814 - RAL 7035’. Site applied, grey coloured (once mixed), two-component epoxy polysulfide resin coating. Mix Part A (light grey, opaque liquid) and Part B (light yellow, translucent liquid) in a 78:22 weight ratio and apply 2 coats as per manufacturer’s TDS ‘MBS_CC-UAE/Pr_1814_06_23/v1/01_24’. Cure coat 1 for 9 hours@25°C. Cure coat 2 for 14 days@25°C. For use with water up to 50°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Icorene 1440 NAT & Icorene 1440 BLK 9001'. Natural (appears off-white) & black, rotationally moulded polyethylene materials. For use with water up to 23°C.
‘Tecotek OP20 BK014 01 0A QF, Tecotek OP20 GR30 BK014 01 0A QF, Tecotek OP20 GR10 BK014 01 0A QF & Tecotek OP20 GR20 BK014 01 0A QF’. Tecotek OP20 BK014 01 0A QF is a black coloured, injection moulded, unfilled PPO/HIPS material. Between February 2024 and April 2025, it was for use with water up to 23°C. Between May 2025 and February 2029, it’s for use with water up to 85°C. Tecotek OP20 GR30 BK014 01 0A QF, Tecotek OP20 GR10 BK014 01 0A QF & Tecotek OP20 GR20 BK014 01 0A QF are black coloured, injection moulded, filled PPO/HIPS materials suitable for use with water up to 85°C.
'NORYL FE1410PW – 73701, NORYL FE1520PW – 73701, NORYL FE1630PW – 73701 & NORYL FE1740PW – 73701'. Black coloured, injection moulded PPE + PS materials. For use with water up to 85°C.
'NORYL FE1410PW - 801' (appears yellow-cream coloured) & 'NORYL FE1410PW - 960' (light-grey coloured). Injection moulded PPE & PS materials. For use with water up to 85°C.
'EH700-144'. Black coloured, compression moulded EPDM material. Shore hardness 72. Tested in-radius size 1.0mm. For use with water up to 85°C.
Range of single hole, single outlet (fixed) electronically controlled tap assemblies, (Chrome plated - brass bodies). Flow is controlled by a solenoid valve activated by via an infra-red sensor. The spout outlets incorporate plastic aerators. Maximum working pressure 10 bar. Maximum operating temperature 60°C.
Range of side or bottom entry BS1212-4 (2016) compact type float operated valve for WC flushing cisterns. The inlet incorporates a flow regulator. Maximum working pressure 10.0 bar. Cold water use only.
Range of bottom and side entry BS1212-4 (2016) compact type float operated valves for WC flushing cisterns, delayed or non-delayed fill. The inlet incorporates a strainer. Maximum working pressure - 10 Bar Cold water use only.
Concealed WC dual flushing cistern with a side entry BS 1212-4 (2016) float operated inlet valve providing a Type AG air gap arrangement and a dual flush outlet valve. The flush volume is operated by a two-push button assembly for a 6 or 3 litre flush volume. The cistern is operated by a manual push button and incorporates a servicing valve and flexible hose on the inlet supply. Maximum working pressure – 10.0 bar, cold water use only.
Range of concealed WC flushing cisterns incorporating a side entry compact type float operated inlet valve providing a Type AG air gap with a dual flush drop valve for full flush volumes of up to 6 litres and a reduced flush of up to 4 litres. The cistern is operated by a manual push button and incorporates a servicing valve and flexible hose on the inlet supply. Maximum working pressure 10.0 bar. Cold water use only.
WC flushing cistern incorporating a side entry compact type float operated inlet valve providing a Type AG air gap with a dual flush drop valve for full flush volumes of up to 6 litres and a reduced flush of up to 4 litres. The cistern is operated by a manual push button and incorporates a servicing valve on the inlet supply. Maximum working pressure 10.0 bar. Cold water use only.
Range of spring loaded resilient trim check valve cartridges with a plastic body and EPDM ‘O’-rings. For insertion into specifically dimensioned bores Maximum working pressure 10 Bar Maximum operating temperature 85°C
In-line non-verifiable check valve assembly with integral isolation valve. Consisting of spring loaded resilient trim check valve cartridge housed within a DZR brass body, verified by test (suitable for backflow protection against Fluid Category 2). Compression connection to be used with copper pipe to BS EN1057. Maximum working pressure 10.0 bar. Maximum operating temperature 85°C.
Single hole, single outlet (fixed) combination tap assembies (brass bodies – various finishes), incorporating a ceramic cartridge headwork with a single lever operating member. The spout outlet incorporates a plastic aerator. Maximum operating pressure 10 bar. Maximum operating temperature 60°C
Range of deck mounted, single-holed, single outlet (fixed) combination tap assemblies (brass bodies – various finishes) incorporating ceramic cartridge headworks with single lever operating members. The spout outlets incorporate plastic aerators. Models (TVW105002000xx, TVW105003000xx, TVW105101110xx & TVW105141110xx) are supplied with lever operated pop-up wastes (not verified by test) Model TVW105105110xx) is supplied with a click type pop-up waste (verified by test). Maximum working pressure 10.0 Bar. Maximum operating temperature 60°C.
Single hole, single outlet (swivel) combination tap assembly (brass body - various finishes), incorporating ceramic cartridge headworks with a single lever operating member. The spout outlet incorporates a plastic flow straightener or plastic aerator. Maximum working pressure 10.0 Bar Maximum operating temperature 65.0°C
Single hole, single outlet (swivel) combination tap assembly (brass body - various finishes), incorporating ceramic cartridge headworks with a single lever operating member. The spout outlet incorporates a plastic flow straightener or plastic aerator. Maximum working pressure 10.0 Bar Maximum operating temperature 65.0°C
Range of single-hole single outlet swivel combination tap assemblies (brass bodies – various finishes), incorporating quarter turn ceramic disc headworks with single lever operating members. The spout outlets incorporate plastic aerators. Maximum working pressure 10 Bar. Maximum operating temperature 65°C.
Range of single hole, single outlet (swivel) combination tap assemblies with (stainless steel bodies - various finishes), incorporating a ceramic cartridge headwork controlling the hot and cold with a single lever operating member. The boiling and purified water is controllied via a ceramic disc headwork incorporating a manual override button and a dome type headwork. Maximum working pressure 8.0 bar. Maximum operating temperature for boiling water pathway: 98 °C; for other water pathway: 85 °C.
Single hole, single outlet (swivel) combination tap assembly (brass body - various finishes), incorporating ceramic cartridge headworks with a single lever operating member. The spout outlet incorporates a plastic flow straightener or plastic aerator. Maximum working pressure 10.0 Bar Maximum operating temperature 65.0°C
Range of two hole, single outlet (fixed) combination tap assemblies (chromium plated brass), incorporating quarter turn ceramic disc headworks with single lever operating members and a manually operated diverter to shower outlet. The spout outlet of the 62638-5101 model incorporates a plastic aerator. The product is supplied with a shower hose and handset and metal backnuts. Maximum working pressure 5.0 bar. Maximum operating temperature 60°C.
Range of Wall mounted, four-hole, single outlet (swivel) combination tap assemblies (Various Finishes). Incorporating a ceramic cartridge headwork controlling the flow to the shower handset and two quarter turn ceramic disc headworks controlling the flow to the spout outlet, all with single lever operating members. The spout outlets incorporate a plastic aerator. The inlet to the shower handsets incorporate an approved check valve cartridge, however, the complete product has not been fully tested to demonstrate it provides backflow protection. Maximum working pressure 10.0 Bar Maximum operating temperature 60.0°C
Range of press copper crimp fittings with EPDM ‘O’-rings for use with copper tube manufactured to EN 1057. The joints are achieved by means of a crimping tool. For above ground use. Maximum working pressure: 16.0 bar. Maximum operating temperature: 85°C
Range of AIS tin-plated brass and PPSU press fit fittings for use with MULTIPIPE multi layered PE-RT/AL/PE-RT pipe. Maximum working pressure 10.0 bar. Maximum operating temperature 70°C.
Page 17 of 25
We use cookies to give you the best possible experience with WRAS. Some are essential to provide website functions and ensure the website is secure. We also use cookies to help us understand how people use the site and to make improvements. Click "Accept All" to enable recommended settings or click "Manage cookies" to adjust your settings. For more details, see our Cookie Policy.
