Range of normally closed inline solenoid valves with a brass body and an EPDM ‘O’-ring, seal and diaphragm. Maximum working pressure 7.0 bar. Cold water use only.
Solenoid valve with a plastic body, EPDM diaphragm and ‘O’-rings. The inlet incorporates a stainless steel strainer. Maximum working pressure 10.0 bar. Maximum operating temperature 70°C
Solenoid valve with a plastic body, incorporating an EPDM diaphram and EPDM sealing rings. Maximum working pressure 10.0 bar. Maximum operating temperature 85°C.
Range of stainless steel spherical valves, incorporating T-type or single lever operating members with a stainless steel ball and PTFE seats. Maximum working pressure 63.0bar
Non-metallic materials and components comply with BS6920 at 80°C
Range of stainless spherical valves, incorporating a stainless steel ball, PTFE seats and single ever operating members. Maximum working pressure 16.0 bar
Non-metallic materials and components comply with BS6920 at 80°C
Range of quarter turn, lever handle or butterfly operated spherical valves with nickel plated brass bodies, chrome plated brass balls and PTFE seals. For use with copper pipe BS EN 1057. Maximum working pressure 25.0 bar. Maximum operating temperature 85°C.
Range of lever operated spherical valves with stainless steel bodies and ball with PTFE seats. Maximum operating pressure 16.0 bar (CF-2EL) or 63.0 bar (CT-3D & CT-2LC).
Non-metallic materials and components comply with BS6920 at 85°C
Range of lever operated spherical valves with DZR brass bodies, chromium plated brass ball, PTFE seats and EPDM ‘O’-rings. Maximum working pressure 25.0 bar. Maximum operating temperature 85°C.
Range of inline spherical valves, (nickel plated brass bodies), chrome plated brass balls, PTFE seats and washers with lock-shield, single lever or T-type operating members. Maximum working pressure: ¼” to 1” = 40.0 bar, 1¼” to 2” = 32.0 bar, 2½” to 3” = 25.0 bar, 4” = 20.0 bar.
Non-metallic materials and components comply with BS6920 at 85°C
In-line spherical valve with a chrom eplasted DZR brass body, brass ball and EPDM ‘O’-rings, incorporating a single check valve cartridge (verified by test, suitable for fluid catergory 2) with a lever operating member. To be used with copper pipe manufactured to EN1057. verified Maximum working pressure 10.0 bar. Maximum operating temperature 85°C.
Range of spherical valves with UPVC bodies and balls, incorporating EPDM seals & `O` rings. Maximum working pressure 16.0 Bar (3101-99BBE to 3101-05BBE) or 10.0 Bar (3101-06BBE to 3101-08BBE, All 3101-XXAAE & all 3101-XXLLE models Cold water use only
Range of gates valve with ductile iron bodies (blue epoxy coating), EPDM seats and `O` rings. The valves are handwheel operated via a non-rising spindle. Maximum working pressure 16.0 bar. Maximum operating temperature 80°C.
Range of resilient seated gate valves with cast iron bodies (blue epoxy coated), EPDM coated cast iron wedges and a handwheel operating member. Maximum working pressure 16.0 bar.
Non-metallic materials and components comply with BS6920 at 85°C
Range of seated gate valves with blue epoxy coated ductile iron bodies, bonnets and ductile iron wedges encapsulated in EPDM. All models have a handwheel operating member. Maximum working pressure 16 bar. Maximum operating temperature 80 °C
Range of gate valves with blue epoxy coated ductile iron bodies and EPDM coated ductile iron wedges. The valves operate via non-rising spindle headwork. Maximum working pressure 10.0 bar and 16.0 bar (dependent on flange pressure rating). Maximum operating temperature 80°C.
Range of gate valves with blue epoxy coated ductile iron bodies and EPDM coated ductile iron wedges. The valves operate via non-rising spindle headwork. Maximum working pressure 16.0 bar and a maximum operating temperature 85°C.
Range of flanged ductile iron, blue epoxy coated gate valves with EPDM seats and hand wheel operating members. Maximum working pressure 16.0 bar.
Non-metallic materials and components comply with BS6920 at 85°C
Range of non-rising spindle gate valves with DZR brass bodies, with PTFE stem packing and gaskets. Operating members are either handwheel operated or lockshield. Maximum working pressure 16 bar. Maximum operating temperature 100°C.
Range of non-rising spindle gate valves with DZR brass bodies, with PTFE stem packing and gaskets. Operating members are either handwheel operated or lockshield. Maximum working pressure 16 bar. Maximum operating temperature 100°C.
Range of gate valves with blue epoxy coated ductile iron bodies, EPDM coated ductile iron wedges, EPDM gasket and ‘O’-ring. The valves operate via non-rising spindle headwork with a hand wheel operating member. Maximum working pressures: DN50: 25.0 bar, DN65-DN600: 16.0 bar.
Non-metallic materials and components comply with BS6920 at 85°C
Range of stop valves with bronze bodies and bonnets. Rising spindle. Maximum working pressure 25.0 bar. Maximum operating temperature 85°C.
Range of automatic thermal balancing valves (DZR Brass) with non-rising spindle headwork, brass disc and EPDM seals. Maximum working pressure 16.0 bar. Maximum operating temperature 100°C.
Magnetic scale reducers, incorporating chrome plated copper body, for use with copper pipe manufactured to BS EN1057. Maximum working pressure 10.0 bar. Cold water use only.
Ultra-violet disinfection unit comprising of a stainless-steel body and quartz sleeve. Maximum working pressure 8.0 bar. Cold water use only.
Range of electronically controlled ion exchange water softeners (salt regenerated) for commercial and domestic use. Maximum working pressure 5.0 bar. Cold water use
'WY-01~-04'. White coloured (opaque), moulded and sintered ceramic material. For use with water up to 85°C.
'DX101, DX201, DX202 & DX203 Rings'. Dark grey coloured, compression moulded silicon carbide ring components. For use with water up to 85°C.
‘Purethane® NXT’. Factory applied, two-component, natural (appears off-white) polyurethane coating. Mix resin and activator in a 2.5:1 volume ratio and apply as per manufacturer’s instructions 'APP-CA-NXT-Rev 03' dated 01.04.2017. Cure for 7 days@23°C. For use with water up to 23°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Euronavy Engineering EW0100'. Factory applied, two-pack white coloured (once mixed) epoxy coating. Mix and apply as per manufacturer's TDS edition 'February 2023'. Cure for 7 days@22°C. For use with water up to 23°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'SIGMALINE 855 (11) Blue'. Factory applied, blue coloured, two-component polyurethane coating. 'SIGMALINE 855 (11) Blue' is for use with water up to 23°C. In September 2024 ‘SIGMALINE 855 (11) Off White’ was added to the approval. Off-white coloured two-component polyurethane coating. 'SIGMALINE 855 (11) Off White' is for use with water up to 36°C. Mix and apply as per manufacturer's Product Data Sheet ‘7656’, dated 'September 16, 2024'. Cure for 12 hours@20°C. These materials are only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the materials are not covered by the scope of the approval.
'Sheraplex Blue, Black, Green & Silver'. Factory applied, organic resin coating system, consisting of a primer and 'Delta Seal' topcoat (available in blue, black, green and silver colours). Apply one coat of primer (as per instructions: WI.BMC.W02 Issue 2 - February 2005) and cure for 2 and ½ hours at 380°C. Then apply a passivation layer through immersion for 15 minutes at 76-99°C (as per instructions: WI.BMC.W06 Issue 1 August 2004). Apply 1 topcoat of 'Delta Seal' (as per instructions WI.BMC.W01A Issue 2 August 2010) and cure for 20 minutes at 200°C. All are for use with water up to 23°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'CSJX53-2 Red'. Factory applied, red coloured polyacrylic resin coating. Apply as per manufacturer's instructions file no. ‘CSJ-0016-1’, version no. ‘A1’, dated 2016.10.12. Cure for 50 minutes@25°C. For use with water up to 23°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
‘Primer coating Spu‐221(A) & Spu‐221(B)’ for use with ‘Top coating: Spu‐222(A) & Spu‐222(B)’. Factory applied, grey coloured (once mixed) Acrylic Polyurethane primer & coating. Mix parts A and B of the primer in a 4:1 volume ratio and apply as per manufacturer’s instructions dated 5th May 2018. Cure for 48 hours@25°C. Mix parts A and B of the topcoat in a 4:2 volume ratio and apply as per manufacturer’s instructions dated 5th May 2018. Cure for 48 hours@25°C. For use with water up to 40°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
‘FIBER TECH 82’. Factory applied, natural (appears dark yellow) fibreglass resin. Spray apply as per manufacturer’s Method Statement Ref ‘PP-GRP-092021-R1’, dated ‘21 Sept 2020’. Cure for 72 hours@25°C. For use with water up to 40°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'JM 9-2910'. Factory applied, blue coloured epoxy powder coating. Apply as per manufacturer's instructions 'edition no.1', issue date 2012-8-5. Cure for 15 minutes@180°C. For use with water up to 85°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'HEMPADUR 85671 System'. Factory applied epoxy coating system comprising of a pink base coat (50900), light green middle coat (42070), and pink top coat (50900 - water contact). Each coat comprises of a base and curing agent to be mixed in a 8.8:1.2 volume ratio before applying in accordance with manufacturer's PDS dated January 2023. Cure each coat for 7 days@20°C and then 20 hours@40°C. For use with water up to 30°C.
'Interline 925P Light Grey & Interline 925P Off White'. Site applied, two component epoxy coatings. Mix Parts A & B in a volume ratio of 3:1 and apply as per manufacturer's datasheet '10257', issue date '07/02/2022'. Cure for 7 days@25°C. For use with water up to 60°C. These materials are only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the materials are not covered by the scope of the approval.
‘Nitocote EP405 (3821)’. Site applied, blue coloured, two component solvent free epoxy resin coating consisting of two bases (coat 1 base; Nitocote EP405 white & coat 2 base; Nitocote EP405 blue) & clear EP405 hardener. Mix parts A & B of each coat in a 100:13 weight ratio and apply in accordance with Fosroc data sheet issue 7 (CI/SfB: Pn6) dated November 2013. Cure coat 1 for 18 hours@7°C. Cure coat 2 for 21 days@7°C. For use with water up to 23°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
‘MoyaProof WS2’. Site applied, grey coloured (once mixed), two-component, polymer modified Portland cement based cementitious waterproofing membrane. Mix Part A (white, opaque liquid) with Part B (grey, opaque powder) in a 1:4 mass ratio and apply two coats as per manufacturer’s Technical Datasheet ‘CC/MP05/Ver09/01/21’. Cure Coat 1 for 2 hours at 5˚C. Cure Coat 2 for 28 days at 5˚C. For use with water up to 23°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Renderoc Plug 20'. Site applied, dark grey coloured, cementitious repair mortar. Mix with water in a 3:1 volume ratio and apply as per manufacturer's datasheet '14' dated 'June 2018'. Cure for 21 days@7°C. For use with water up to 23°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Klüberbeta VR 67-17002'. Cream coloured silicone grease intended for use as a lubricant. For use with water up to 85°C.
'Unisilkon L200'. White coloured silicone grease intended for use as a lubricant. For use with water up to 85°C.
'YC-FM01'. Dark grey coloured, pressed and sintered Strontium Ferrite magnet. For use with water up to 85°C.
'15.0903.01 & 15.0902.01'. Dark grey coloured, ferrite anisotropic magnets (commonly known as ceramic magnets). For use with water up to 85°C.
'Polimid A 50 GF Natural WR'. Natural (appears off-white/beige), 50% glass fibre reinforced, injection moulded PA66 material. For use with water up to 85°C.
'Polimid A 50 GF Black WR'. Black coloured, 50% glass fibre reinforced, injection moulded PA66 material. For use with water up to 23°C.
'Polimid A 30 GF Black WR'. Black coloured, 30% glass fibre reinforced, injection moulded PA66 material. For use with water up to 85°C.
‘Zytel® FG70G30HSR2 BK309’. Black coloured, injection moulded polyamide material. For use with water up to 23°C. From January 2024, the material is for use with water up to 60°C.
‘AL ZAMIL roto moulded tank panel’. White coloured, roto-moulded, multi-layered PE tank panel. For use with water up to 60°C.
‘AL ZAMIL blow moulded tank panel’. Pale blue coloured, blow-moulded, multi-layered PE tank panel. For use with water up to 60°C.
Page 132 of 222
We use cookies to give you the best possible experience with WRAS. Some are essential to provide website functions and ensure the website is secure. We also use cookies to help us understand how people use the site and to make improvements. Click "Accept All" to enable recommended settings or click "Manage cookies" to adjust your settings. For more details, see our Cookie Policy.
