'VYDYNE AG10K-BK1066'. Black coloured, (50% glass Fibre reinforced) polyamide 66 material. For use with water up to 23°C. From January 2024, the material is for use with water up to 60°C.
'ELCRIN WF006LiQ-1001'. Grey coloured, injection moulded, glass fibre reinforced PBT material. For use with water up to 85°C.
'EUREXPOL PI6808C'. Yellow coloured, isophthalic unsaturated polyester resin material made by mixing and pouring into a mould. For use with water up to 23°C.
'Akansu Plastik HDPE Pipe'. Extruded HDPE pipes available in blue or black colours. For use with water up to 65°C.
'FRIALEN Safety Fittings'. Black coloured, PE100 fittings which are injection moulded or machined from an extruded pipe. Between May 2023 and June 2025, the fittings were for use with water up to 23°C. Between July 2025 and May 2028, the black fittings are for use with water up to 60°C. Blue coloured PE100 fittings which are injection moulded. For use with water up to 23°C.
'3-layers Stars Water Tank Panel'. Three-layered, roto-moulded LLDPE foam panel comprising of a white (opaque) water contact layer, black (opaque) middle layer and white (opaque) outer layer. For use with water up to 65°C.
'Hepworth HDPE PE 100 Pipe (black) & HDPE PE 100 Pipe (black with blue stripes)'. Extruded polyethylene pipes. For use with water up to 60°C.
‘Sikaplan® WT 4220-15 C & Sikaplan® WT 4220-18 H’. ‘Sikaplan® WT 4220-15’ is a light blue coloured, extruded multi-layer polyethylene sheet material comprising of glass fibre inlay between two polyethylene sheet layers. ‘Sikaplan® WT 4220-18 H’ is a light blue coloured, extruded polyethylene sheet material. For use with water up to 60°C.
'PP-R Instaplast'. Grey coloured, extruded polypropylene pipe, available with or without a red coloured, external stripe. For use with water up to 60°C.
'PG6-S09'. Beige coloured, injection moulded PP+GF30 material. For use with water up to 85°C.
'Teflon® FEP 100 X, 100-J, 106 X, CJ 95 X, CJ 99 X & 9302 X'. Un-pigmented (white coloured, compression moulded FEP material. For use with water up to 85°C.
''Teflon® PFA 340 X, 345 X, 350 X, 350-T-J, 440 HP X, 445 HP X, 450 HP X & 416 HP X'. Unpigmented (white coloured), compression moulded PFA materials. For use with water up to 85°C.
'Teflon® PTFE 640XT X, 807N X, NXT 70, NXT 75, 6CN X, 62 X, 62N X, 62XT X, 669N X, 669 X, NXT 85, 605XT X, 6C X, 7A X, 641XT X & 650XT X’. White coloured, extruded or compression moulded PTFE material. For use with water up to 85°C.
‘Estane® Grades 58887 Nat 036, 58315 Nat 033, 58300 Nat 036, 58887 Nat 029, 58315 Nat 055, 58887 Nat 038 & 58887 Nat 055’. Natural (transparent, colourless), injection moulded TPU materials. For use with water up to 23°C.
'TOM Oriented PVC (PVC-O) pipe'. Blue coloured PVC pipe manufactured by extrusion and orientation. For use with water up to 60°C.
'STATHEROS EPC80'. Site applied, grey coloured (once mixed), two-component anchor resin, supplied in a cartridge which automatically dispenses in a 1:1 ratio. Apply and cure as per manufacturer's product information 'Ver. 10' dated '02/06/23' (refer to working and loading times table for cure). For use with water up to 23°C. For use only as a resin anchor having been tested at a reduced surface area to volume ratio of 1,000mm² per 1 litre of water. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'E7001Z59 (EP02269PF) 2x modified'. Black coloured, compression moulded EPDM 'O' rings. Shore hardness 72 A. Tested in-radii sizes between 1.4mm & 1.8mm. For use with water up to 85°C.
'5613 Gaskets'. Black coloured, compression moulded EPDM gaskets. Shore hardness 60. Tested in-radius size 3.0mm. For use with water up to 23°C.
'TIMO 4-80 ‘O’ rings and washers'. Black coloured, injection moulded EPDM ‘O’ rings and washers. Shore hardness 80. The ‘O’ rings have an in-radius size of between 0.52mm & 2.67mm. The washers have an in-radius size of between 0.52mm & 2.71mm. For use with water up to 85°C.
'TIMO 7-70 washers & 'O' rings'. Black coloured, injection moulded EPDM washers and 'O' rings. Shore hardness 70. Tested in-radii sizes between 0.5 and 2.6mm. For use with water up to 85°C.
'EPDM 70.503-00 'O'-rings and washers'. Black coloured, injection moulded EPDM 'O'-rings and washers. Shore hardness 70. Tested in-radius size between 0.5mm & 2.6mm. For use with water up to 85°C.
'Sunaflex T 8165'. Black coloured, compression moulded EPDM sheet material. Shore hardness 70. Tested in-radius size 1.0mm. For use with water up to 23°C.
'SE-618PF'. Black coloured, compression moulded EPDM material. Shore hardness 60. Tested in-radius size 1.0mm. For use with water up to 85°C.
'Mescola EPDM-PX 659/70.nr'. Black coloured, compression moulded EPDM material. Shore hardness 70. Tested in-radius size 1.0mm. For use with water up to 85°C.
'0612 HNBR'. Yellow coloured (opaque), injection moulded HNBR 'O' rings. Shore hardness 70. Tested in-radius size 1.31mm. For use with water up to 85°C.
‘N5066F, N5566F, N6066F, N6566F, N7066F, N7566F, N8066F, N8566F & N9066F’. Black coloured, compression moulded NBR rubber `O` rings and gaskets. Shore hardness between 50 & 90. 'O' rings have a tested in-radius size of between 0.25mm & 5.0 mm. Gaskets have a tested in-radius size of between 0.3mm & 7.5mm. For use with water up to 85°C.
‘N70 60 003 197’. Black coloured, injection moulded NBR material. Shore hardness 70. Tested in-radius size 1.0mm. For use with water up to 85°C.
‘SIL40X02, SIL45X02, SIL50X02, SIL55X02, SIL60X02, SIL65X02, SIL75X02 & SIL80X02’. Range of compression moulded, silicone rubber `O` rings and gaskets available in natural, white, grey, blue, red, pale yellow, orange, green, brown and black colours. Shore hardness range 40 - 80. ‘SIL70B02’ – Blue coloured. ‘SIL70W01’ – Natural. ‘SIL70R01’ – Red coloured. ‘SIL7001’ – Black coloured. Range of compression moulded, silicone rubber `O` rings and gaskets available in colours listed above. Shore hardness 70. ‘O’ rings have an in-radius size range of 0.2mm – 5.0mm. Gaskets have an in-radius size range of 0.3mm – 7.5mm. For use with water up to 85°C.
'EMS Force 5543'. 'EMS Force 5543-P' was added to the approval in February 2025. Blue coloured pipe sealants. Apply as per manufacturer's instructions 'TLM.LB.07', version '0', issue date '07/03/2016'. Cure for 24 hours@23°C. For use with water up to 85°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Hinton Thread Sealant HTS50 & HTS250'. Anaerobic adhesive which is available in a yellow colour or in a yellow/orange colour. Apply as per manufacturer's instructions dated '2023-06-07', 'review 6' and cure for 15 minutes@25°C or 24 hours@22°C. For use with water up to 85°C. This product is to be applied and cured in strict accordance with the manufacturer's instructions.
'Hinton Solvent Cement HSC125 & HSC250'. Clear, transparent (un-pigmented) solvent cement, (intended to join PVC pipe and fittings). Apply as per manufacturer's instructions 'Rev00 02062023'. Cure for 20 days at 7°C. For use with water up to 65°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'IPF-PVC-U-H2O Pipe'. Grey coloured, extruded u-PVC pipe. For use with water up to 60°C.
Bottom entry BS1212-4 (2016) compact type float operated valve for WC flushing cisterns. The inlet incorporates a flow restrictor. Maximum working pressure 10.0 bar. Cold water only
Side entry BS1212-4 (2016) compact type float operated valve for WC flushing cisterns. The inlet incorporates a flow restrictor. Maximum working pressure 10.0 bar. Cold water use only.
Side entry BS1212-4 (2016) compact type float operated valve for WC flushing cisterns. Maximum working pressure 10.0 bar. Cold water use only.
Concealed WC flushing cisterns incorporating a side entry compact type float operated inlet valve providing a Type AG air gap with a dual flush drop valve for full flush volumes of up to 6 litres and a reduced flush of up to 4 litres. The cistern is operated by an electronically controlled flush valve. Maximum working pressure 10.0 bar. Cold water use only
WC flushing cistern incorporating a side entry BS 1212-4 compact type float operated inlet valve providing a Type AG air gap with a dual flush drop valve for full flush volumes of up to 6 litres and a reduced flush of up to 4 litres. The cistern is operated by electronic or manual actuation. Maximum working pressure 10.0 bar. Cold water use only
Range of concealed WC dual flushing cisterns with a vertical BS 1212-4(2016) float operated inlet valve providing a Type AG air gap arrangement and a dual flush outlet valve. The flush volume is operated by a two-push button assembly. The product also incorporates a servicing valve and flexible hose on the inlet supply. Maximum working pressure 10 Bar, cold water use only.
Range of non-verifiable single check valve assemblies with DZR brass bodies. Maximum working pressure 16.0 bar.
Non-metallic materials and components comply with BS6920 at 85°C
Range of flow restrictors with natural/unpigmented plastic bodies and inserts (where applicable), and EPDM ‘O’-rings. The LFB-FDN15, BFDN15SH & LFB-FDN15SH models also incorporate a stainless-steel filter.
Non-metallic materials and components comply with BS6920 at 85°C
Range of quarter turn ceramic disc headworks with brass bodies and NBR ‘O’ rings, for insertion into specifically dimensioned bores. Maximum working pressure 10.0 Bar Maximum operating temperature 85.0°C
Non-metallic materials and components comply with BS6920 at 85°C
Range of ceramic cartridge headworks with plastic bodies and EPDM ‘O’-rings for insertion into specifically dimensioned bores. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C
Range of ceramic cartridge headworks with plastic bodies for insertion into specifically dimensioned bores. Maximum working pressure 10.0 bar.
Non-metallic materials and components comply with BS6920 at 65°C
Range of ceramic disc headwork cartridges with diverter function, incorporating plastic bodies, NBR ‘O’-rings and silicone seals. For insertion into specifically dimensioned bores. Maximum working pressure 16.0 Bar.
Non-metallic materials and components comply with BS6920 at 85°C
Range of single-hole, single outlet, (fixed), combination tap assemblies, (chrome plated brass bodies. Incorporating ceramic cartridge headworks with single lever operating members. The spout outlet incorporates plastic aerators. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C
Range of single hole, single outlet (fixed) combination tap assemblies (brass bodies – various finishes) incorporating ceramic cartridge headworks with single lever operating members. The spout outlets incorporate plastic aerators. Maximum working pressure: See Models
Non-metallic materials and components comply with BS6920 at 60°C
Range of single hole, single outlet (fixed) combination tap assemblies with brass bodies (chromium plated), incorporating ceramic cartridge headworks, a single lever operating member and a plastic aerator. The products are supplied with either a lever type pop up waste or a click type waste. Maximum operating pressure 10.0 bar. Maximum working temperature 60°C.
Range of single-hole, single outlet, fixed combination tap assemblies (brass bodies – various finishes), incorporating a ceramic cartridge headworks with single lever operating members. The spout outlets incorporate plastic aerators. The product is supplied with a click-type pop-up waste. Maximum operating pressure 10.0 bar
Non-metallic materials and components comply with BS6920 at 65°C
Range of deck mounted, single-hole, fixed combination tap assemblies (chromium plated brass), incorporating a ceramic cartridge headwork with single lever operating members. The spout outlets incorporate plastic aerators. Models 26216 and 26216MINI are fitted with pre fitted copper tails and provide 3/8” BSP to ½” BSP adapters and isolation valves. Models 2621 and 2621MINI are provided with pre-installed steel braided PEX lined flexible hose assemblies with ⅜” captive nut end connections. Maximum working pressure 10.0 Bar. Maximum operating temperature 60.0°C.
Non-metallic materials and components comply with BS6920 at 60°C
Range of floor mounted single hole, single outlet (fixed) combination tap assemblies (brass bodies - various finishes). Incorporating a ceramic cartridge headwork with either a lever or joystick type operating member and a self-cancelling diverter to shower outlet. The spout outlet incorporates a plastic aerator. The shower outlet connection incorporates an approved check valve cartridge; however, the complete product has not been fully tested to demonstrate it provides backflow protection. Maximum working pressure 10.0 Bar Maximum operating temperature 60.0°C
Page 80 of 171
We use cookies to give you the best possible experience with WRAS. Some are essential to provide website functions and ensure the website is secure. We also use cookies to help us understand how people use the site and to make improvements. Click "Accept All" to enable recommended settings or click "Manage cookies" to adjust your settings. For more details, see our Cookie Policy.
