'JSAW-JAL (Cement-SDC)'. Factory applied, grey coloured, Sulphate Resisting Portland Cement mortar. Mix cement, sand and water in a 1:1.5:0.5 weight ratio. Cure for 2 hours and 30 minutes@45°C and 85 relative humidity. Then cure again for 3 days@30°C and 80% relative humidity. For use with water up to 65°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mix and cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'JSAW-JAL (Cement-SIL)'. Factory applied, grey coloured Ordinary Portland Cement mortar. Mix cement, sand and water in a 1:1.5:0.5 weight ratio. Cure for 2 hours and 30 minutes@45°C and 85 relative humidity. Then cure again for 3 days@30°C and 80% relative humidity. For use with water up to 65°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mix and cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'JSAW-JAL (Cement-JSL)'. Factory applied, grey coloured Blast Furnace Slag Cement mortar. Mix cement, sand and water in a 1:1.5:0.5 weight ratio. Cure for 2 hours and 30 minutes@45°C and 85 relative humidity. Then cure again for 3 days@30°C and 80% relative humidity. For use with water up to 65°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mix and cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Jerlac Two-Pack Epoxy Blue – 746 & Jerlac Two-Pack Epoxy Red – 747'. Factory applied, blue or red coloured, two-component epoxy coatings. Mix resin and hardener in a 3:1 volume ratio and apply as per manufacturer's instructions. Cure for 7 days@30°C. For use with water up to 60°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'SF4300'. Nitrile rubber/aramid fibre, calendered material which is white coloured on one side and green coloured on the other side. For use with water up to 23°C.
'Extrastrong SMC/ESF-30-10' pipe. Natural (appears pale green coloured) GRE pipe manufactured by filament winding. For use with water up to 70°C.
'Zytel® RSFG30G50L BK595'. Black coloured, injection moulded glass fibre reinforced nylon (polyamide 610) material. For use with water up to 85°C.
'Zytel® FG70G30HSR3 BK309'. Black coloured, injection moulded nylon material. For use with water up to 85°C.
'Tecomid NB40 GR30 NL HC QW'. Off-white coloured (translucent), injection moulded PA6 material. For use with water up to 85°C.
'4MID 9B22130 W-A BNL100'. Off-white coloured (translucent), injection moulded PA6 material. For use with water up to 85°C.
'PB DKG 300'. Natural, (appears beige coloured), compression moulded polybutylene material. For use with water up to 85°C.
`Veradel 3330GF`. Beige coloured, injection moulded polyethersulfone material. For use with water up to 85°C.
'Isoglas H30FVL (c) NA'. Translucent, off-white coloured, injection moulded, polypropylene material. For use with water up to 85°C.
'Rainson PP IOCL 3030MG Blue & Rainson PP IOCL 3030MG Black'. Injection moulded polypropylene materials. 'Rainson PP IOCL 3030MG Blue' is for use with water up to 23°C. 'Rainson PP IOCL 3030MG Black' is for use with water up to 65°C.
'E300'. Black coloured, compression moulded EPDM material. Shore hardness 70. Tested in-radius size 1.0mm. For use with water up to 85°C.
‘Silopren LSR 2030, 2040, 2050, 2060, 2070 & 2080’. Natural (appears clear), compression moulded silicone rubbers with a shore hardness between 30 and 80. Tested in-radius size 1.0mm. For use with water up to 85°C.
Range of deck mounted, single hole, single outlet (fixed) electronically controlled tap assemblies (brass body - various finishes, see model). Flow is controlled by a solenoid valve activated via an infra-red sensor. The spout outlet incorporates a plastic aerator. The inlet hose incorporates an approved single check valve cartridge, however, the complete assembly has not been tested to demonstrate it provides backflow protection. Maximum working pressure 8.0 bar. Maximum operating temperature 60°C.
Range of deck mounted, single hole, single outlet (fixed) electronically controlled tap assemblies (brass body - various finishes, see model). Flow is controlled by a solenoid valve activated via an infra-red sensor. The product incorporates a manual temperature control operated by a single lever on the side of the body. The spout outlet incorporates a plastic aerator. The inlet hoses incorporate an approved single check valve cartridge, however, the complete assembly has not been tested to demonstrate it provides backflow protection. Maximum working pressure 8.0 bar. Maximum operating temperature 60°C.
Deck mounted, single hole, single outlet (fixed) electronically controlled tap assembly (various finishes). The flow is controlled by a solenoid valve activated via an infra-red sensor. The spout outlet incorporates a plastic aerator. Product supplied with metal backnuts. Maximum working pressure 6.0 bar. Maximum operating temperature 40°C.
Wall mounted, single hole, single outlet (fixed) electronically controlled tap assembly (various finishes). The flow is controlled by a solenoid valve activated via an infra-red sensor. The spout outlet incorporates a plastic aerator. Maximum working pressure 6.0 bar. Maximum operating temperature 40°C.
Range of single hole, single outlet, fixed, electronically controlled tap assemblies with brass bodies (various finishes), incorporating an electronic cartridge controlling the flow which is activated via an infrared sensor (either battery or mains powered). Models 31 171 xxx & 31 173 xxx incorporates a manually operated temperature control. The inlet adapters incorporate stainless steel filters and single check valve cartridges verified by test (suitable for backflow protection against Fluid Category 2 ). The spout outlets incorporate a plastic aerator. Maximum working pressure 8.0 bar. Maximum operating temperature 60°C.
Range of BS1212-4 (2016) compact type float operated valves for WC flushing cisterns, bottom or side entry type. The inlet incorporates a strainer. Maximum working pressure 10.0 bar. Cold water use only.
Range of concealed WC flushing cisterns incorporating a side entry compact type float operated inlet valve providing a Type AG air gap with a dual flush drop valve for full flush volumes of up to 6 litres and a reduced flush of up to 4 litres. The cistern is operated by a manual push button and incorporates a servicing valve and flexible hose on the inlet supply. Maximum working pressure 10.0 bar. Cold water use only.
Concealed WC dual flushing cistern with a BS 1212-4 (2016) float operated inlet valve providing a Type AG air gap arrangement and a dual flush pneumatic outlet valve. The flush volume is operated by a two-push button assembly for a 6 or 3 litre flush volume. Maximum working pressure 10.0 bar. Cold water use only.
Concealed WC dual flushing cistern with a BS 1212-4 (2016) float operated inlet valve providing a Type AG air gap arrangement and a dual flush outlet valve. The flush volume is operated by a two push button assembly for a 6 or 3 litre flush volume. Incorporating a servicing valve on the inlet supply. Maximum working pressure 10.0 bar. Cold water use only.
Range of floor mounted, single hole, single outlet (fixed), combination tap assemblies (chromium plated brass), incorporating a ceramic cartridge headwork with a single lever operating member and a manual diverter to shower outlet. The spout outlet incorporates a plastic aerator (SH-T9050N model) or a plastic flow straightener (all other models). Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.
Range of one-piece and two-piece pre-insulated GRP cold water storage cisterns. Cisterns are supplied with a float operated inlet valve, screened overflow and screened vent. Cold water use only.
Range of push to open, push to close headworks with plastic bodies and EPDM ‘O’-rings. For insertion into specifically dimensioned bores. Maximum working pressure 10.0 bar. Maximum operating temperature 70°C.
Range of ceramic disc diverter headworks with or without a on/off function, to be installed in specifically dimensioned bores. Maximum working pressure 12.0 bar. Maximum operating temperature 85°C.
Range of thermostatic cartridges with brass or plastic bodies (see model) and EPDM ‘O’-rings. The GR-FX-02S, 03SC, 10T, 11T, X02S, X02T & X05 models incorporate a stainless-steel strainer. For insertion into specifically dimensioned bores. Maximum operating temperature 75°C.
Range of thermostatic cartridges with plastic bodies and EPDM ‘O’-rings. All models incorporate a plastic strainer. For insertion into specifically dimensioned bores. Maximum working pressure 16 bar. Maximum operating temperature 60°C.
Single hole, single outlet (fixed) combination tap assembly (chrome plated brass) body. Incorporating a single sequential headwork with a single lever operating member. The spout outlet incorporates a plastic straightener. Maximum working pressure 3 bar. Maximum operating temperature 42°C
Range of single hole, single outlet fixed combination tap assemblies, incorporating brass bodies (various finishes). Model 3034-CR has a non-rising spindle headwork with cross top operating members. All other models have a ceramic cartridge headwork with single lever operating member. The spout outlets incorporate a plastic aerator. Maximum operating pressure 5.0 bar. Maximum operating temperature 60°C.
Range of single hole, single outlet (fixed) combination tap assemblies (chromium plated brass), incorporating a ceramic cartridge headwork with either a single lever or dome type operating member (see model). The spout outlet incorporates a plastic aerator (specific models only - see model section). Maximum working pressure 5.0 bar. Maximum operating temperature 60°C.
Range of single hole, single outlet (fixed) combination tap assemblies (brass bodies, various finishes - see model), incorporating a ceramic cartridge headwork with a single lever operating member. The spout outlet incorporates a plastic flow straightener. Maximum operating pressure 5.0 bar. Maximum operating temperature 65°C.
‘Grandera’ range of single hole, single outlet (fixed) combination tap assemblies (brass bodies - various finishes, see model), incorporating a ceramic cartridge headwork with a single lever operating member. The spout outlet incorporates a plastic aerator. The 23.303 prefix models are supplied with a pop-up waste. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.
Range of single hole, single outlet (fixed) combination tap assemblies with brass bodies (various finishes - see model), incorporating a ceramic cartridge headwork with a single lever operating member. The spout outlet incorporates a plastic aerator. The inlets incorporate approved check valve cartridges however, the complete product has not been fully tested to demonstrate it provides backflow protection. The products are supplied with a click type pop-up waste. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.
Range of single hole, single outlet (fixed) combination tap assemblies (brass bodies, various finishes - see model), incorporating a ceramic cartridge headwork with a single lever operating member and a self- cancelling diverter to shower outlet. The spout outlet incorporates a plastic aerator. The outlet from the self-cancelling diverter incorporates an approved check valve cartridge (except model 31 930 xx0), Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.
Range of single hole, single outlet (swivel) combination tap assemblies (chromium plated brass), incorporating a ceramic cartridge headwork with a single lever operating member. The spout outlets incorporate a plastic aerator. The 32 082 xxx model is supplied with a click type waste, the 32 084 xxx & 71 130 xxx models have a pop-up waste. Maximum working pressure 10.0 bar. Maximum operating temperature 65°C.
Range of single hole, single outlet (swivel) combination tap assemblies (chromium plated brass) incorporating ceramic cartridge headwork and single lever operating member. The spout outlets incorporate a plastic aerator. The inlet hose incorporates an approved check valve cartridge; however, the complete product has not been fully tested to demonstrate it provides backflow protection. Maximum working pressure 5.5 bar. Maximum operating temperature 60°C.
Range of single hole, double outlet (swivel) combination tap assemblies with brass bodies (chrome plated), incorporating quarter turn ceramic disk headworks with a single lever operating member. The spout outlet incorporates a plastic aerator. Maximum working pressure 5.0 bar. Maximum operating temperature 60°C.
Range of two hole, single outlet, (fixed) combination tap assemblies (chromium plated brass), With a quarter turn ceramic disc headwork with single lever operating members. Models M4306, M4306E & M4306F incorporate a non rising spindle headwork with dome type operating members. Model M4306G incorporate a non rising spindle headwork with cross top operating members. The spout outlets incorporate a plastic flow straightener and the products are supplied with metal backnuts. . Maximum working pressure 10.0 bar. Maximum operating temperature 85°C.
Range of two-hole, single outlet (fixed) combination tap assemblies (chromium plated brass) incorporating quarter turn ceramic disc headworks with cubed or dome operating members. The spout outlet incorporates a plastic flow straightener. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.
Range of two-hole, deck mounted single outlet (fixed) combination tap assemblies incorporating brass body (various finishes) and quarter turn ceramic disc headwork with single lever operating members. The spout outlets incorporate a plastic aerator and the products are supplied with metal backnuts. Maximum working pressure 5.0 bar. Maximum operating temperature 60°C.
Range of wall mounted, two-hole, single outlet (fixed) combination tap assemblies, comprising of a concealed rough in set with a brass body incorporating a ceramic cartridge headwork with a single lever operating member and a spout outlet. The spout outlet incorporates a plastic aerator. Maximum working pressure 10.0 Bar. Maximum operating temperature 85°C.
Range of wall mounted two hole, single outlet, (fixed) combination tap assemblies with brass bodies (various finishes), incorporating ceramic cartridge headwork with single lever operating members. The spout outlets incorporate a plastic aerator Maximum working pressure 10.0 bar. Maximum operating temperature 65°C.
Range of two-hole, single outlet (fixed) combination tap assemblies (chromium plated brass) incorporating quarter turn ceramic disc headwork with single lever or dome type operating members. The spout outlet of model 60828-5301 incorporates a plastic flow straightener. The spout outlet of models 62277-5001 & 62277-5101 incorporates a plastic aerator. Model 62277-5101 is supplied with metal backnuts. Models 60828-5301 & 62277-5001 are supplied with plastic backnuts. Maximum working pressure 5.0 bar. Maximum operating temperature 60°C
Range of deck mounted, two hole, single outlet (fixed) combination tap assemblies with brass bodies (chrome plated). Incorporating quarter turn ceramic disc headworks, dome type operating members and self cancelling diverter to shower outlet. The temperature is controlled independently via a thermostatic cartridge with a dome type operating member that also incorporates a manual override button. Both inlets incorporate approved check valve cartridges, however, the complete product has not been fully tested to demonstrate it provides backflow protection. The spout outlet incorporates a plastic aerator. Models TL30024CP and TR30024CP are supplied with a shower riser rail, shower hose and shower handset. Maximum working pressure 5.0bar. Maximum operating temperature 60°C.
Range of wall mounted, two hole, single outlet (fixed) combination tap assemblies with brass bodies (chrome plated). Incorporating non-rising spindle headworks, dome type operating members and lockable, self cancelling diverter to shower outlet. The temperature is controlled independently via a thermostatic cartridge with a dome type operating member that also incorporates a manual override button. Both inlets incorporate stainless-steel strainer and approved check valve cartridges, however, the complete product has not been fully tested to demonstrate it provides backflow protection. The spout outlet incorporates a plastic aerator. Maximum working pressure 5.0 bar. Maximum operating temperature 60°C.
Range of wall mounted concealed, three-hole, single outlet (fixed) combination tap assemblies (brass body). Incorporating quarter turn ceramic disc headworks with dome or cube type operating members (see models). The spout outlet incorporates a plastic aerator. Maximum working pressure 10 bar. Maximum operating temperature 60°C.
Page 6 of 46
We use cookies to give you the best possible experience with WRAS. Some are essential to provide website functions and ensure the website is secure. We also use cookies to help us understand how people use the site and to make improvements. Click "Accept All" to enable recommended settings or click "Manage cookies" to adjust your settings. For more details, see our Cookie Policy.
