'Delrin® RAFG511DP NC010'. White coloured, injection moulded semi-opaque acetal material. For use with water up to 85°C.
'POWTON E5000P-WT'. Factory applied, blue coloured epoxy powder coating. Apply as per manufacturer's TDS 'issue reference SPI 20170215' dated 21st January 2015. Cure for 15 minutes@230°C. For use with water up to 85°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'POWTON E5000P-WT (grey)'. Factory applied, grey coloured, epoxy powder coating. Apply as per manufacturer's TDS dated January 21st 2015. Cure for 15 minutes@230°C. For use with water up to 85°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Jotaguard VA 5001'. Blue coloured, factory applied, Fusion Bonded Epoxy Powder Coating. Apply as per manufacturer's application guide dated 'October 2018'. Cure for 5 minutes@245°C. For use with water up to 85°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'JPC Liquid Epoxy Paint'. Factory applied, red coloured, two-component epoxy paint. Mix components A & B in a 3:1 volume ratio and apply as per manufacturer's instructions ' JPC-FG-A/06-21/009 & JPC-FG-B/06-21/009' dated '02/06/2021'. Cure for 7 days@34°C. For use with water up to 23°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the materials are not covered by the scope of the approval.
'KARUMEL EX4412 (RAL5005) & KARUMEL EX4412 (Blue)'. Factory applied, blue coloured epoxy powder coatings. Apply as per manufacturer's application guide for potable water reference number 'KCSA-21090101' dated September 2021. For use with water up to 85°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'LNXFSY'. Factory applied, grey coloured Portland Cement Mortar. Mix cement, sand and water in a 2:1:0.4 mass ratio and apply as per manufacturer's instructions issue 'X202101207F' dated '2021-12-07'. Cure for 12 hours@55°C. For use with water up to 65°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the materials are not covered by the scope of the approval.
'Ya-Coat Amiantit (SADIP)'. Factory applied, two-component, green coloured (once mixed and applied) PU coating. Mix base and hardener in a 3:1 volume ratio and apply as per manufacturer's process document 'MW 106-5 issue 1', dated 26/06/2007. Cure for 10 minutes@35°C. For use with water up to 23°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the materials are not covered by the scope of the approval.
'Desmopol DW'. Factory applied, two-component, cream coloured (once mixed and applied) polyurethane resin coating. Mix components A & B in a 4:1 volume ratio and apply as per manufacturer's TDS 'DESMOPOL DW v.11-03-2022'. Cure for 6 hours@23°C. For use with water up to 23°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the materials are not covered by the scope of the approval.
'Eurokote® 48-20'. Factory applied, blue coloured, two component epoxy coating consisting of a resin and hardener. Mix resin and hardener in a mass ratio of 68:32 and apply as per manufacturer's TDS dated 10/12/2018. Cure for 24 hours@20°C. For use with water up to 60°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'MS 1555'. Factory applied, dark blue/grey coloured vitreous enamel coating. Apply as per manufacturer's instructions 'I.PBE.06.04' dated November 22, 2021 and 'TPE.09.056.02' dated August 19, 2014. Cure for 14 minutes@850°C. For use with water up to 85°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Versathane'. Site applied, two-component, grey coloured (once mixed) polyurethane coating. Mix the grey coloured (opaque) base coating with the amber coloured hardener in a 3:1 volume ratio and apply Coat 1 as per manufacturer's product data sheet 'Issue No. 01 Sep 2016. Cure for 4 hours@7°C. Mix and apply Coat 2 using the same mix ratio and application instructions and then cure for 14 days@7°C. For use with water up to 23°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the materials are not covered by the scope of the approval.
'Vandex Super'. Site applied, two-component, grey coloured (once mixed) cementitious coating. Mix cement powder with water in a weight ratio of 5:2. Apply as per manufacturer's Instructions for Use '2nd issue', dated '18.11.2020'. Cure for 21 days@7°C. For use with water up to 23°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the materials are not covered by the scope of the approval.
‘Sikalastic P 770’ (formerly known as ‘MasterSeal P 770’) Primer for use with ‘Sikalastic M 808’ (formerly known as ‘MasterSeal M 808 Grey’, and ‘MasterSeal M 808 Light Grey’) topcoats. Site applied coating system, which is light grey coloured (once mixed and applied), comprising of a primer and polyurethane coatings. Coat 1 primer: Mix parts A & B of ‘Sikalastic P 770’ Primer in a weight ratio of 2.2:2.8. Apply as per manufacturer’s IFU ‘version No. 1’, dated ‘22nd November 2024’. Cure for 24 hours@7°C. Coat 2 (coating): Mix parts A & B of ‘Sikalastic M 808’, dark grey coloured (once mixed) polyurethane coating in a weight ratio of 3.3:1.7. Apply as per manufacturer’s IFU ‘version No. 1’, dated ‘22nd November 2024’. Cure for 6 hours@7°C. Coat 3 (water contact coating): Mix parts A & B of ‘Sikalastic M 808’, light grey coloured (once mixed) polyurethane coating in a weight ratio of 3.3:1.7. Apply as per manufacturer’s IFU ‘version No. 1’, dated ‘22nd November 2024’. Cure for 7 days@7°C. When applying the coating system to GRP there is no need to apply a primer. Mix, apply and cure ‘Sikalastic M 808’ dark grey and then mix, apply and cure ‘Sikalastic M 808’ light Grey (water contact layer) as detailed above. For use with water up to 23°C.
'Resichem 507 DWPU Blue & Grey'. Site applied, two-component polyurethane coatings which are available in blue or grey colours (once mixed). Mix Part A (blue or grey opaque liquid) with Part B (amber, translucent liquid) in a 100:30.5 weight ratio and apply as per manufacturer's technical data sheet 'TDS507DWPU.rv4.09062022'. Cure for 14 days@7°C. For use with water up to 23°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the materials are not covered by the scope of the approval.
'TPU inner hose (YOUSHI/3017)'. Transparent, colourless, extruded TPU hose. For use with water up to 85°C.
'Purolite C107E'. Cream coloured ion exchange resin. For use with water up to 23°C.
'Purolite® C104E/5264'. Cream coloured ion exchange resin. For use with water up to 23°C.
`VIP Universal Pipe Lubricant`. Translucent, amber coloured, soya oil lubricant. Apply as per manufacturer's technical datasheet issued 'Nov 2019'. For use with water up to 23°C.
'K422'. Clear, silicone lubricant aerosol. Apply as per manufacturer's instructions 'version 1.0' dated 'May 2022'. For use with water up to 85°C.
'Hydro 90'. Clear, silicone lubricant aerosol. Apply as per manufacturer's instructions 'version 1.0' dated 'June 2022'. For use with water up to 85°C.
'Zytel® FG101L NC010 & Zytel® FG42A NC010'. Un-pigmented (appear off-white, translucent), injection moulded nylon materials. For use with water up to 23°C.
'Zytel® HTNFG52G35HSLR BK011'. Black coloured, injection moulded polyphthalamide (PPA) material. For use with water up to 85°C.
'Ultramid D3EG10 FC Aqua Black 23285'. Black coloured, injection moulded polyamide material. For use with water up to 65°C.
'KN133G50 (beige coloured) & KN133G50BL (black coloured)'. Injection moulded PA6 materials. For use with water up to 65°C.
'Pocan B1700 000000'. Natural (appears white in colour), injection moulded PBT material. For use with water up to 23°C.
'Al Jubail PE100 Pipe'. Black coloured, extruded HDPE Pipe. For use with water up to 70°C.
'DH-01 Pipe'. Blue coloured, extruded HDPE pipe. For use with water up to 65°C.
`Hydro Dynamic PE100 Pipes`. Black coloured, extruded polyethylene pipes. For use with water up to 60°C.
'DURAFIDE® 1140A1 WF9050 & DURAFIDE® 1140A1 WK9050'. Black coloured, injection moulded PPS materials. For use with water up to 85°C.
‘FORTRON 9115L0 SD3039 BLACK (formerly known as FORTRON MT9115L0 SD3039 DW black) & FORTRON 9141L4 SD3039 BLACK (formerly known as FORTRON MT9141L4 SD3039 DW black’). Black coloured, injection moulded PPS materials. For use with water up to 85°C.
‘RTP 199 X 146499 S-202865 White’. White coloured (opaque), injection moulded PP material. For use with water up to 50°C.
‘Chemfix PESF TOP’. Site applied, grey coloured chemical anchor resin which is supplied in a pre-mixed cartridge. Apply as per manufacturer’s instructions 'Chemfix Polyester Styrene Free', rev. 1 dated 03/02/2022. Cure for 4 days@7°C. For use with water up to 23°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'V7500BK'. Black coloured, Fluororubber material manufactured by mould pressing. Shore hardness 75. Tested in-radius size 1.04mm. For use with water up to 23°C.
'4270' components. Black coloured, injection moulded EPDM rubber components with a shore hardness of 70. ‘O’ rings (in-radius 1.31mm), washers (in-radius 1.05mm) & membranes (in-radius 1.75mm) made in Italy. ‘O’ rings (in-radius 1.31mm) & washers (in-radius 1.05mm) made in China. In May 2024 ‘shaped seals’ (in-radius of 1.8mm) made in Italy, were added to the approval. In November 2024, lip seals (in-radius of 0.7mm) made in Italy, were added to the approval. For use with water up to 85°C.
'EPDM G7503'. Black coloured, injection moulded EPDM rubber material. Shore hardness 75. Tested in-radius size 1.1mm. For use with water up to 50°C.
'TIMO 7 NC-70'. Black coloured, injection moulded EPDM material. Shore hardness 70. Tested in-radius size 1.0mm. For use with water up to 85°C.
'AES-2/EPDM-50'. Black coloured, compression moulded EPDM sheet material. Shore hardness 50. Tested in-radius size 1.1mm. For use with water up to 65°C.
'AEH-5/EPDM-80'. Black coloured, compression moulded EPDM material. Shore hardness 80.Tested in-radius size 1.1mm. For use with water up to 23°C.
'EP701253C'. Black coloured, compression moulded EPDM material. Shore hardness 70. Tested in-radius size 1.0mm. For use with water up to 85°C.
'E2514'. Black coloured, compression moulded EPDM rubber. Shore hardness 67. Tested in-radius size 1.03mm. For use with water up to 60°C,
'AA7LNZ'. Black coloured, compression moulded EPDM material. Shore hardness 70. Tested in-radius size 1.0mm. For use with water up to 85°C.
'XR0240012'. Black coloured, compression moulded EPDM material. Shore hardness 40. Tested in-radius size 1.5mm. For use with water up to 85°C.
'Seat Seal S1 & S2'. Black coloured (S2) or white coloured (S1), injection moulded silicone rubber components. Shore hardness 80. Tested in-radius size between 0.65mm & 1.54mm. For use with water up to 85°C.
'Silopren LSR 2630, 2640, 2650, 2660 & 2670'. Natural (appears clear), compression moulded silicone rubber sheet materials. Shore hardness between 30 & 70. Tested in-radius size of 1.0mm. For use with water up to 85°C.
'Brymec PVC Solvent Cement'. Clear, transparent (un-pigmented) solvent cement, (intended to join PVC pipe and fittings). Apply as per manufacturer's instructions 'TDS Brymec CEMENT Rev 01' review date '27-05-2022'. Cure for 20 days at 7°C. For use with water up to 65°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'XFGJ-2022'. Factory applied, grey coloured Portland Cement Mortar. Mix cement, sand and water in a 2:1:0.4 mass ratio and apply as per manufacturer's instructions issue 'X20220228F' dated '2022-2-28'. Cure for 12 hours@55°C. For use with water up to 65°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the materials are not covered by the scope of the approval.
'SPS-2022'. Factory applied, grey coloured Portland Cement Mortar. Mix cement, sand and water in a 2:1:0.4 mass ratio and apply as per manufacturer's instructions issue 'S20220601' dated '2022-6-1'. Cure for 12 hours@55°C. For use with water up to 65°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the materials are not covered by the scope of the approval.
'6083 black'. Black coloured, injection moulded CIIR rubber material. Shore hardness 50. Tested in-radius size 1.1mm. For use with water up to 70°C.
Range of deck mounted, single hole, single outlet (fixed) electronically operated tap assemblies (Chromium plated brass). Flow is controlled by a solenoid valve activated via an infra-red sensor. The products are supplied with a tee piece for installation prior to the solenoid valve. The inlets of the tee piece incorporate a combined NBR gasket and stainless steel filter and an approved check valve cartridge, however, the complete product has not been fully tested to demonstrate it provides backflow protection. The products are also supplied with stainless steel braided PEX lined flexible (connecting) hose assemblies and angled spherical valves incorporating a stainless steel strainer for installation on each inlet. Temperature is controlled by adjusting the opening of each angled spherical valve. The spout outlet incorporates a plastic aerator. Maximum working pressure 5.0 bar. Maximum operating temperature 60°C
Page 36 of 209
We use cookies to give you the best possible experience with WRAS. Some are essential to provide website functions and ensure the website is secure. We also use cookies to help us understand how people use the site and to make improvements. Click "Accept All" to enable recommended settings or click "Manage cookies" to adjust your settings. For more details, see our Cookie Policy.
