In-line spherical valve with a chrom eplasted DZR brass body, brass ball and EPDM ‘O’-rings, incorporating a single check valve cartridge (verified by test, suitable for fluid catergory 2) with a lever operating member. To be used with copper pipe manufactured to EN1057. verified Maximum working pressure 10.0 bar. Maximum operating temperature 85°C.
Range of quarter turn, lever handle or butterfly operated spherical valves with nickel plated brass bodies, chrome plated brass balls and PTFE seals. For use with copper pipe BS EN 1057. Maximum working pressure 25.0 bar. Maximum operating temperature 85°C.
SFGV Range of gate valves with ductile iron bodies (blue epoxy coated) and EPDM rubber coated wedges. Maximum working pressure 16.0 bar. Maximum operating temperature 60°C
Range of gate valves with blue coloured epoxy coated ductile iron body and EPDM coated wedge. The valves operate via a non-rising spindle headwork with hand wheel operating member. Maximum working pressure 16.0 bar. Maximum operating temperature 80°C.
Range of angled, screw down stop valves with brass bodies and NBR rubber gasket and ‘O’-rings. Maximum working pressure 10.0 bar. Cold water use only.
Range of screw down stop valves with brass bodies and bonnets and EPDM seats. Maximum working pressure 20.0 bar. Cold water use only.
Range of in line regulating valves with gunmetal bodies and EPDM ‘O’-rings. The valves incorporate a non-rising spindle headwork for regulating the flow. Maximum working pressure 16.0 bar. Maximum operating temperature 90°C.
Range of balancing valves with brass or stainless steel bodies and EPDM ‘O’-rings. Maxmimum working pressure 16.0 bar. Maximum operating temperature 90°C.
Range of double regulating valves with gunmetal bodies and EPDM seals. Maximum working pressure 16.0 bar. Maximum operating temperature 90°C.
Range of in-line electrolytic or magnetic sale reducers with nickel plated brass bodies. Electrolytic models have a zinc alloy core and magnetic models have a ferrite magnet core. All models are for use with copper pipe manufactured to EN 1057. Maximum working pressure 10.0 bar. Cold water use only.
Range of UV disinfection units with stainless steel bodies and EPDM seals. The UV lamps are housed inside quartz tubes. Maximum working pressure 10.3 bar. Maximum operating temperature 40°C.
'Bottom Plate K3'. Off-white (opaque) coloured, injection moulded POM component. For use with water up to 65°C.
'OSH046 (white) & OSH046 (grey)'. White or grey coloured, injection moulded ABS materials. For use with water up to 85°C.
'LNXFSY'. Factory applied, grey coloured Portland Cement Mortar. Mix cement, sand and water in a 2:1:0.4 mass ratio and apply as per manufacturer's instructions issue 'X202101207F' dated '2021-12-07'. Cure for 12 hours@55°C. For use with water up to 65°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the materials are not covered by the scope of the approval.
'Ya-Coat Amiantit (SADIP)'. Factory applied, two-component, green coloured (once mixed and applied) PU coating. Mix base and hardener in a 3:1 volume ratio and apply as per manufacturer's process document 'MW 106-5 issue 1', dated 26/06/2007. Cure for 10 minutes@35°C. For use with water up to 23°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the materials are not covered by the scope of the approval.
'Desmopol DW'. Factory applied, two-component, cream coloured (once mixed and applied) polyurethane resin coating. Mix components A & B in a 4:1 volume ratio and apply as per manufacturer's TDS 'DESMOPOL DW v.11-03-2022'. Cure for 6 hours@23°C. For use with water up to 23°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the materials are not covered by the scope of the approval.
'Eurokote® 48-20'. Factory applied, blue coloured, two component epoxy coating consisting of a resin and hardener. Mix resin and hardener in a mass ratio of 68:32 and apply as per manufacturer's TDS dated 10/12/2018. Cure for 24 hours@20°C. For use with water up to 60°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'MS 1555'. Factory applied, dark blue/grey coloured vitreous enamel coating. Apply as per manufacturer's instructions 'I.PBE.06.04' dated November 22, 2021 and 'TPE.09.056.02' dated August 19, 2014. Cure for 14 minutes@850°C. For use with water up to 85°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Versathane'. Site applied, two-component, grey coloured (once mixed) polyurethane coating. Mix the grey coloured (opaque) base coating with the amber coloured hardener in a 3:1 volume ratio and apply Coat 1 as per manufacturer's product data sheet 'Issue No. 01 Sep 2016. Cure for 4 hours@7°C. Mix and apply Coat 2 using the same mix ratio and application instructions and then cure for 14 days@7°C. For use with water up to 23°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the materials are not covered by the scope of the approval.
‘RTU AL 5023, RTU AL 5002A, RTU AL 5054, AL 8050, AL 8783 & AL 8062-1’. Factory applied, dark blue coloured enamel coatings. Apply as per manufacturer’s instructions version ‘11-2021’. Cure for 7 minutes@857°C. For use with water up to 85°C. These materials only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the materials are not covered by the scope of the approval.
`Scotchkote 206N`. Factory applied, green coloured, epoxy powder coating. Apply and cure as per manufacturer’s 'standard cure guide' which appears in document '80-6111-8352-8 Rev. B'. For use with water up to 23°C.
'Resichem 507 DWPU Blue & Grey'. Site applied, two-component polyurethane coatings which are available in blue or grey colours (once mixed). Mix Part A (blue or grey opaque liquid) with Part B (amber, translucent liquid) in a 100:30.5 weight ratio and apply as per manufacturer's technical data sheet 'TDS507DWPU.rv4.09062022'. Cure for 14 days@7°C. For use with water up to 23°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the materials are not covered by the scope of the approval.
'KLINGERSIL® C-4324'. Fibre/rubber gasket material, manufactured by calendaring, which is green coloured on one side and black coloured on the other. Shore hardness 65. For use with water up to 85°C. For use only as a jointing/gasket material having been tested at a reduced surface area to volume ratio.
'Crystic LS96PA Clear Gel Coat' for use with 'Crystic 2-446 PA GRP resin'. Contact moulded GRP resin, manufactured by hand lamination, for use with off-white coloured, factory applied gel coat. Apply as per manufacturer's quick guide 'issue number 1', dated 04/06/2018. Cure for 24 hours@23°C and then 3 hours@80°C. For use with water up to 23°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Crystic Vinyl Ester VE671PA'. Brown coloured (translucent), contact moulded GRP laminating material. For use with water up to 23°C.
‘SEA2001’ (manufactured in Italy, Poland & Turkey). Dual layer, extruded, composite hoses. Hoses with a black coloured inner layer and either a red or blue coloured outer layer are suitable for use with water up to 60°C. Hoses with a straw coloured, translucent inner and outer layer are suitable for use with water up to 60°C. Hoses with a black coloured inner layer and either a white or grey coloured outer layer are suitable for use with water up to 23°C. From January 2023 hoses with a black coloured inner layer and either a white or grey coloured outer layer are suitable for use with water up to 60°C.
'Purolite® C104E/5264'. Cream coloured ion exchange resin. For use with water up to 23°C.
'Glidex Tap Lubricant'. White coloured silicone lubricant. For use with water up to 60°C.
'Glidex Silicone Paste'. White coloured lubricant. For use with water up to 60°C.
'KN133G50 (beige coloured) & KN133G50BL (black coloured)'. Injection moulded PA6 materials. For use with water up to 65°C.
'Pemaron660G6W NC02'. Natural (appears beige in colour), injection moulded, glass fibre reinforced PA66 material. For use with water up to 23°C.
'DH-01 Pipe'. Blue coloured, extruded HDPE pipe. For use with water up to 65°C.
'DH-02 Fitting'. Blue coloured, injection moulded HDPE fitting. For use with water up to 65°C.
`Hydro Dynamic PE100 Pipes`. Black coloured, extruded polyethylene pipes. For use with water up to 60°C.
'LL 8460.29'. Natural (appears white and opaque) LLDPE material manufactured by rotational moulding. For use with water up to 85°C.
‘Smart Home Pipes’. Extruded, single layered PPR, Multi-layered PPR (Fibre Glass) and Multi-layered PPR (Aluminium) pipes. The single layered pipe is green coloured. Multi-layered PPR (Fibre Glass) pipe: green coloured, PP-R inner layer, black coloured, glass-fibre reinforced PP-RC second layer, green coloured PP-R third layer and black coloured, PP-R outer layer. Multi-layered PPR (Aluminium) pipe: green coloured, PP-R inner layer, green coloured, glass-fibre reinforced PP-RC second layer, aluminium third layer and black coloured, PP-R outer layer. All are for use with water up to 65°C.
'Smart Home Fittings'. Black or green coloured, injection moulded PPR fittings. For use with water up to 65°C.
‘RTP 199 X 146499 S-202865 White’. White coloured (opaque), injection moulded PP material. For use with water up to 50°C.
'Tamkeen Modern Pipe White, Light Grey and Dark Grey'. Extruded PVC pipes. For use with water up to 60°C.
‘GF PVCU fittings manufactured from HS1013, IR348 & HS1014’. From September 2023 onwards, the fittings may also be made using 'IR 349'. Grey coloured, injection moulded PVC-U fittings. For use with water up to 60°C.
'TIMO 7 NC-70 'O'-rings and washers'. Black coloured, injection moulded EPDM 'O'-rings and washers. Shore hardness 70. Tested in-radius size between 0.5mm & 2.6mm. For use with water up to 85°C.
'AES-2/EPDM-50'. Black coloured, compression moulded EPDM sheet material. Shore hardness 50. Tested in-radius size 1.1mm. For use with water up to 65°C.
'E2514'. Black coloured, compression moulded EPDM rubber. Shore hardness 67. Tested in-radius size 1.03mm. For use with water up to 60°C,
'EPDM 69064340'. Black coloured, injection moulded EPDM sheet material. Shore hardness 57. Tested in-radius size 0.9mm. For use with water up to 23°C.
'RE EP/50, 'RE EP/60, 'RE EP/70 & RE EP/80'. Black coloured, compression moulded EPDM materials. Shore hardness between 50 & 80. Tested in-radius size 1.0mm. For use with water up to 60°C.
'Seat Seal S1 & S2'. Black coloured (S2) or white coloured (S1), injection moulded silicone rubber components. Shore hardness 80. Tested in-radius size between 0.65mm & 1.54mm. For use with water up to 85°C.
'Brymec PVC Solvent Cement'. Clear, transparent (un-pigmented) solvent cement, (intended to join PVC pipe and fittings). Apply as per manufacturer's instructions 'TDS Brymec CEMENT Rev 01' review date '27-05-2022'. Cure for 20 days at 7°C. For use with water up to 65°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'XFGJ-2022'. Factory applied, grey coloured Portland Cement Mortar. Mix cement, sand and water in a 2:1:0.4 mass ratio and apply as per manufacturer's instructions issue 'X20220228F' dated '2022-2-28'. Cure for 12 hours@55°C. For use with water up to 65°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the materials are not covered by the scope of the approval.
'SPS-2022'. Factory applied, grey coloured Portland Cement Mortar. Mix cement, sand and water in a 2:1:0.4 mass ratio and apply as per manufacturer's instructions issue 'S20220601' dated '2022-6-1'. Cure for 12 hours@55°C. For use with water up to 65°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the materials are not covered by the scope of the approval.
Range of floor standing, single hole, single outlet (fixed) combination tap assemblies (brass body in various finishes), incorporating a ceramic disc headwork with single lever operating member (model OMI-133 & IND-OMI133-XXX) OR ceramic cartridge headwork with a single lever operating members (all other models) and a lockable self-cancelling diverter to shower outlet. All models except OMI-133-C/P and IND-OMI133-XXX are supplied with an approved check valve cartridge at the inlet, however, the complete product has not been fully tested to demonstrate it provides backflow protection. The spout outlet incorporates a plastic aerator and the product is supplied with a shower hose and handset. Maximum working pressure 5.0 bar. Maximum operating temperature 60°C.
Page 35 of 177
We use cookies to give you the best possible experience with WRAS. Some are essential to provide website functions and ensure the website is secure. We also use cookies to help us understand how people use the site and to make improvements. Click "Accept All" to enable recommended settings or click "Manage cookies" to adjust your settings. For more details, see our Cookie Policy.
