'70NB502S'. Black coloured, compression moulded NBR material. Shore hardness 70. Tested in-radius size 1.0mm. For use with water up to 85°C.
'50SIL332P 'O' ring'. Grey coloured, compression moulded silicone rubber 'O' ring. Shore hardness 50. Tested in-radius size 0.5mm. For use with water up to 85°C.
'E-Tupling Plastic Pipe Cement 125 ml ETSC125' & 'E-Tupling Plastic Pipe Cement 250 ml ETSC250'. Clear, transparent (un-pigmented) solvent cements, (intended to join PVC pipe and fittings). Apply as per manufacturer's instructions 'Rev00 08052025'. Cure for 20 days at 7°C. For use with water up to 65°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'TODAY TOOLS PVC SOLVENT CEMENT 125ML SC1' & 'TODAY TOOLS PVC SOLVENT CEMENT 250ML SC2'. Clear, transparent (un-pigmented) solvent cement, (intended to join PVC pipe and fittings). Apply as per manufacturer's instructions 'Rev00 08052025'. Cure for 20 days at 7°C. For use with water up to 65°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'TW Tools PVC Pipe Cement 125ml' & 'TW Tools PVC Pipe Cement 250ml'. Clear, transparent (un-pigmented) solvent cement, (intended to join PVC pipe and fittings). Apply as per manufacturer's instructions 'Rev00 08052025'. Cure for 20 days at 7°C. For use with water up to 65°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'AquaPure 2025'. Beige coloured tube manufactured by winding PET fibre and epoxy vinylester resin over a mandrel under heat and pressure, intended for the manufacture of bearings. For use with water up to 23°C.
Deck mounted pillar tap, (chrome plated brass) body. The flow is controlled by a solenoid valve which is actuated manually via rotary control switch using cross top operating members. Maximum working pressure 5.0 Bar Maximum operating temperature 85.0°C
Range of single hole, single outlet (fixed) electronically controlled tap assemblies (stainless steel bodies, various finishes). Flow is controlled by a solenoid valve activated by via an infra-red sensor. The spout outlet incorporates a plastic aerator. Depending on model the products are supplied with either a stainless steel braided PEX lined flexible hose assembly with 15mm spigot end connection or 10mm copper tail (see models). Maximum working pressure 8.0 Bar Maximum operating temperature 60.0°C
Bottom entry BS1212-4 (2016) compact type float operated valves for use with WC flushing cisterns. The inlet incorporates a strainer. Maximum working pressure 10.0 bar. Cold water use only.
Bottom entry BS1212 part 4 (2016) compact type float operated inlet valve for WCs flushing cistern having a plastic body and adjustable float and plastic filter at the inlet. Maximum working pressure 10.0 bar. Cold water use only.
Floor mounted, single outlet (fixed) combination tap assembly (chrome plated brass) incorporating a ceramic cartridge headwork with a single lever operating member and a self-cancelling diverter to shower outlet with a Type HC backflow protection device (verified by test - suitable for backflow protection against Fluid Category 3)he shower outlet incorporates a single check valve cartridge; however, the complete product has not been fully tested to demonstrate it provides backflow protection. The spout outlet incorporates a plastic aerator, and the product is supplied with an approved shower hose and handset. Maximum working pressure 10.0 bar. Maximum operating temperature 70°C.
Floor standing single hole, single outlet (fixed) combination tap assembly (chrome plated brass) body, incorporating a ceramic cartridge headwork with a single lever operating member and a self-cancelling diverter to a shower outlet with a Type HC backflow protection device (verified by test - suitable for backflow protection against Fluid Category 3). The outlet to the shower incorporates an approved check valve cartridge however, the complete product has not been fully tested to demonstrate it provides backflow protection. The spout outlet incorporates a plastic aerator. Maximum working pressure 5.0 bar. Maximum operating temperature 70°C
Range of wall mounted, two hole, single outlet (fixed) combination tap assemblies (chromium plated brass), incorporating a non-rising spindle headwork with a single lever operating member. The temperature is controlled independently via a thermostatic cartridge incorporating a single lever operating member. Each inlet incorporates a combined washer and stainless-steel strainer, and an approved check valve cartridge, however, the complete product has not been fully tested to demonstrate it provides backflow protection. The spout outlet incorporates a self-cancelling diverter to shower outlet with Type HC device (verified by test - suitable for backflow protection against Fluid Category 3) and a plastic flow straightener. Maximum working pressure 5.0 bar. Maximum operating temperature 85°C
Deck mounted, two-hole, single outlet (fixed) combination tap assemby (brass body, various finishes - see model), incorporating ¼ turn ceramic disc headworks with single lever operating member. The spout outlet incorporates a self-cancelling diverter to shower outlet with Type HC device (verified by test - suitable for backflow protection against Fluid Category 3) and a plastic aerator. The products are supplied with metal back nuts. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.
Range of floor mounted, single hole, single outlet, swivel combination tap assemblies (brass bodies – various finishes) incorporating a ceramic cartridge headwork with a single lever operating member and a self-cancelling diverter to shower outlet. The shower outlet incorporates a single check valve cartridge; however, the complete product has not been fully tested to demonstrate it provides backflow protection. The spout outlet incorporates a plastic aerator and the product is supplied with an approved shower hose and handset. Maximum working pressure 10.0 bar. Maximum operating temperature 70°C.
Range of wall mounted, two-hole, single outlet (fixed) combination tap assemblies (chrome plated brass) bodies. The flow is controlled via a solenoid valve activated via an infra-red sensor. The temperature is controlled independently via a thermostatic cartridge. The products incorporate approved check valve cartridges; however, the complete product has not been fully tested to demonstrate it provides backflow protection. The inlets incorporate a stainless-steel strainer. The products are supplied with spherical valves for both inlets. Maximum working pressure 5.0 bar. Maximum operating temperature 65°C.
Range of shower kits with a shower hose, handset and shower rail. Maximum operating temperature 60 °C. Open outlet use only.
Range of shower sets with shower hose, handset and riser rail. Open outlet use only. Maximum operating temperature 65 °C.
Range of wall mounted shower kits. Comprising of brass bodied wall mounted shower outlet, shower hose and handsets (various finishes), incorporating an approved check valve cartridge, however, the complete product has not been fully tested to demonstrate it provides backflow protection. Maximum working pressure 3.5 bar. Maximum operating temperature 60*C
Range of double check valve assemblies, incorporating two spring loaded resilient trim in-line check valve cartridges housed in DZR brass or nickel plated DZR brass bodies. Compression connection to be used with copper pipe EN1057. Maximum working pressure 10.0 bar. Maximum operating temperature 85°C.
Sequential ceramic cartridge headwork incorporating a plastic body and silicone seals. Maximum working pressure 5.0 Bar Maximum operating temperature 85 °C.
Single hole, single outlet (swivel) combination tap assembly (chromium plated brass), incorporating a ceramic cartridge headwork with a single lever operating member. The spout outlet is a pull-down spray type incorporating a push button. The connection to the pull-down hose incorporates an approved single check valve cartridge, however, the whole product has not been fully tested to demonstrate that it provides backflow protection. Maximum working pressure 5.0 Bar.
Non-metallic materials and components comply with BS6920 at 65°C
Range of single hole, single outlet (swivel) combination tap assemblies incorporating a brass body (various finishes) and ceramic cartridge headwork with single lever operating members. The outlets incorporate a plastic aerator. Model CO721XX incorporates a pull-out spray with push button trigger assembly. The pull-out spray incorporates a single check valve assembly (however the complete unit has not been tested to demonstrate it provides adequate backflow protection). Model CO713XX incorporates a pull-down outlet. Maximum working pressure 5.0 bar. Maximum operating temperature 60°C.
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| 193746 X XXX | VARIOUS | 1/2" BSP | 5.0 bar | 85 °C | PPI | REAR OF BODY | No | Ceramic cartridge | C-plate | Flow Straightener |
X XXX Denotes the following: First X: Different handle and the second, third & fourth XXX for different finishes: Handles: A (Lever type) Chrome – No suffix, Brushed brass – BGP, PVD Gold – PVD, Brushed Nickel – BN1, Gun Metal – GMG, Matt Black – MBK, Matt White – MWH, Stainless Steel – SS1, Black Chrome – BCP, Titanium – TIB and Antique Bronze – AB1.
Single hole, single outlet (fixed) combination tap assembly (chromium plated brass), incorporating a quarter turn ceramic disc headworks with single lever operating members. The spout outlets incorporates a stainless steel strainer and plastic flow strainer or a plastic aerator. The products are supplied with a click type waste. Maximum working pressure 10.0 Bar. Maximum operating temperature 65°C.
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| F8142KP-** | Various | 1/2" captive nut | 10 bar | 60 °C | LANBIAO | Body | No | Ceramic cartridge | C-plate | Flow Straightener | |
| F8122KP-** | Various | 1/2" captive nut | 10 bar | 60 °C | LANBIAO | Body | No | Ceramic cartridge | C-plate | Flow Straightener | |
| F8142KPM-** | Various | 1/2" captive nut | 10 bar | 60 °C | LANBIAO | Body | No | Ceramic cartridge | C-plate | Flow Straightener |
1）Model No. without Suffix-Chrome 2) -**Represents the following different surface treatments: 1. H-Black 2. DYB - Matte white 3. BZ - Perl white painted 4. HGTS - Red bronze 5. HTL = Yellow bronze brushed 6. Q = Bronze 7. QTSL = Bronze brushed bright 8. QTS = Bronze brushed matte 9. STS = Acid copper brushed 10. SDMGJ = Water plated rose gold 11. N = Nickel brushed bright light 12. NP = Nickel brushed 13. TJ = Titanium gold 14. TJLS = Titanium gold brushed 15. G = Gold 16. GJS = Gold brushed 17. GJSY = Zirconium gold wire drawing matte 18. PGJFY = Zirconium gold wire drawing matte bright light 19. PLSJ = Brushed gold 20. LSJY = Brushed gold matte 21. MGJ = Rose gold 22. MGJL = Rose gold brushed 23. DMGJ = Light rose gold brushed 24. HTS = Red bronze brushed 25. QHP = Grey 26. LSQH = Grey brushed 27. LHMGJ = Brushed yellow rose gold 3) The finish is on metal body
Single hole, single outlet (swivel) combination tap assembly with a brass body incorporating a quarter turn ceramic disc headworks with single lever operating members. The spout outlets incorporate plastic aerator or flow straightener with a stainless steel strainer. Maximum working pressure 10.0 bar. Maximum operating temperature 65°C
Single hole, single outlet (swivel) pull out spray combination tap assemblies (brass bodies – various finishes) incorporating a ceramic cartridge headwork with a single lever operating member. The outlet incorporates a plastic aerator and a push button spray. The connection between the outlet and the hose incorporates an approved single check valve cartridge, however, the whole product has not been fully tested to demonstrate that it provides adequate backflow protection. Maximum working pressure 5.0 Bar. Maximum operating temperature 65.0°C
Non-metallic materials and components comply with BS6920 at 65°C
Single hole, single outlet (swivel) combination tap assemblies (brass body - various finishes), incorporating ceramic cartridge headworks with a single lever operating member. The spout outlet incorporates a plastic flow straightener or plastic aerator. Maximum working pressure 10.0 Bar Maximum operating temperature 65.0°C
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| 12101246 | Various | 1/2" captive nut | 10 bar | 65 °C | EASO | Rear of body | No | 1/4 Turn ceramic disk | Nut with screws | Aerator |
Chrome plated, Brushed brass, Brushed nickel or Matt black
A range of single hole, single outlet (swivel) combination tap assemblies (brass bodies, various finishes - see model), incorporating quarter turn ceramic disc headworks with single lever operating members. The spout outlet incorporates a plastic aerator. The product is also supplied with an alternative spout outlet that incorporates a plastic flow straightener and a stainless-steel strainer. The products are supplied with a loose brass ½” BSP (M) x ½” BSP (F) adaptor for installation on the cold inlet. This adaptor incorporates a single check valve cartridge, verified by test (suitable for backflow protection against Fluid Category 2). Maximum working pressure 5.0 bar. Maximum working temperature 60°C.
Two hole, single outlet fixed combination tap assembly (chrome plated brass body) incorporating quarter turn ceramic disc valve headworks with single lever operating members. The spout outlet incorporates a plastic flow straightener. Product is supplied with metal back nuts. Maximum working pressure 5.0 bar. Maximum operating temperature 60°C.
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| COB BF C | CHROME | 3/4" BSP (M) | 5 bar | 60 °C | Bristan | Handle or Body | No | 1/4 Turn ceramic disk | Metal Backnuts | Flow Straightener | |
| RP3 COB BF C | CROME | 3/4" BSP (M) | 5 bar | 60 °C | Bristan | Handle or Body | No | 1/4 Turn ceramic disk | Metal Backnuts | Flow Straightener | |
| COB BF BLK | BLACK | 3/4" BSP (M) | 5 bar | 60 °C | Bristan | Handle or Body | No | 1/4 Turn ceramic disk | Metal Backnuts | Flow Straightener | |
| 144347 | CHROME | 3/4" BSP (M) | 5 bar | 60 °C | Bristan | Handle or Body | No | 1/4 Turn ceramic disk | Metal Backnuts | Flow Straightener | |
| 257580 | BLACK | 3/4" BSP (M) | 5 bar | 60 °C | Bristan | Handle or Body | No | 1/4 Turn ceramic disk | Metal Backnuts | Flow Straightener |
Two hole, single outlet fixed combination tap assembly (brass body - Gun Metal finish)incorporating quarter turn ceramic disc headworks with single lever operating members. The spout outlet incorporates a plastic flow straightener. The products are supplied with metal backnuts. Maximum working pressure 10.0 bar.
Non-metallic materials and components comply with BS6920 at 65°C
Range of two hole, single outlet (fixed) combination tap assembly (chrome plated brass) incorporating quarter turn ceramic disk headworks with single lever operating members. The spout outlet incorporates a stainless steel strainer and a plastic flow straightener.
Non-metallic materials and components comply with BS6920 at 65°C
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| F8125KP | Various | BSP 3/4" (M) | 10 bar | 85 °C | “LANBIAO” | Body | No | 1/4 Turn ceramic disk | Metal Backnuts | Flow Straightener | |
| F8145KP | Various | BSP 3/4" (M) | 10 bar | 85 °C | “LANBIAO” | Body | No | 1/4 Turn ceramic disk | Metal Backnuts | Flow Straightener |
1）No Suffix-Chrome 2) -**Represents the following different surface treatments: 1.H-Black 2.DYB - Matte white 3.BZ - Perl white painted 4.HGTS - Red bronze 5.HTL = Yellow bronze brushed 6.Q = Bronze 7.QTSL = Bronze brushed bright 8.QTS = Bronze brushed matte 9.STS = Acid copper brushed 10.SDMGJ = Water plated rose gold 11.N = Nickel brushed bright light 12.NP = Nickel brushed 13.TJ = Titanium gold 14.TJLS = Titanium gold brushed 15.G = Gold 16.GJS = Gold brushed 17.GJSY = Zirconium gold wire drawing matte 18.PGJFY = Zirconium gold wire drawing matte bright light 19.PLSJ = Brushed gold 20.LSJY = Brushed gold matte 21.MGJ = Rose gold 22.MGJL = Rose gold brushed 23.DMGJ = Light rose gold brushed 24.HTS = Red bronze brushed 25.QHP = Grey 26.LSQH = Grey brushed 27.LHMGJ = Brushed yellow rose gold 3) The finish on metal body
Wall mounted thermostatic blending valve (brass body, various finishes - see model) incorporating a 2-way ceramic disc headwork with a single lever operating member controlling and diverting the flow between the spout outlet or the shower outlet. Temperature is controlled independently via a thermostatic cartridge with a single lever operating member incorporating a manual override button. Both inlets incorporate a stainless-steel strainer and an approved check valve cartridge, however, the complete product has not been fully tested to demonstrate it provides backflow protection. The spout outlet incorporates a plastic aerator. Maximum working pressure 16.0 bar. Maximum operating temperature 75°C.
Range of two-hole, single outlet (fixed) combination tap assemblies (chrome plated brass bodies) incorporating quarter turn ceramic disc headworks with lever type operating members and a manually operated diverter to the shower outlet. The spout outlets incorporate plastic flow straighteners. The product is supplied with a shower hose, shower handset and metal backnuts. Maximum working pressure 10.0 bar.
Non-metallic materials and components comply with BS6920 at 65°C
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| M5005 X XXX | VARIOUS | 3/4" BSP | 10.0 bar | 65 °C | PPI | REAR OF BODY | No | 1/4 Turn ceramic disk | Metal Backnuts | Open Outlet | Shower Hose, Handset, |
X XXX Denotes the following: First X: Different handle and the second, third & fourth XXX for different finishes: Handles: A (Lever type) Chrome – No suffix, Brushed brass – BGP, PVD Gold – PVD, Brushed Nickel – BN1, Gun Metal – GMG, Matt Black – MBK, Matt White – MWH, Stainless Steel – SS1, Black Chrome – BCP, Titanium – TIB and Antique Bronze – AB1.
Two hole, single outlet (swivel) combination tap assembly with brass bodies (chrome plated), incorporating quarter turn ceramic disc headworks and single lever operating members. The spout outlet incorporates a plastic aerator or plastic flow straightener. The product is supplied with metal backnuts. Maximum working pressure 10.0 bar. Maximum operating temperature 65°C.
Range of two hole, double outlet (swivel) combination tap assemblies (chromium plated brass). The TAP2014 model incorporates non-rising spindle headworks with dome type operating members. The TAP 9023 model incorporates quarter turn ceramic disc headworks with single lever operating members. The spout outlets incorporate a plastic flow straightener. The products are supplied with metal backnuts. Maximum working pressure 5.5 bar. Maximum operating temperature 70°C.
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Wastes | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|---|
| CLS201 | Various | 1/2 | 6Bar bar | 65 °C | Waterworks | Body | No | 1/4 Turn ceramic disk | Plastic Backnuts | Aerator | Click Type | Interconnecting Hoses, |
| CLS211 | Various | 1/2 | 6Bar bar | 65 °C | Waterworks | Body | No | 1/4 Turn ceramic disk | Plastic Backnuts | Aerator | Click Type | Interconnecting Hoses, |
| CLS214 | Various | 1/2 | 6Bar bar | 65 °C | Waterworks | Body | No | 1/4 Turn ceramic disk | Plastic Backnuts | Aerator | Click Type | Interconnecting Hoses, |
| CLS215 | Various | 1/2 | 6Bar bar | 65 °C | Waterworks | Body | No | 1/4 Turn ceramic disk | Plastic Backnuts | Aerator | Click Type | Interconnecting Hoses, |
| BLS210 | Various | 1/2 | 6Bar bar | 65 °C | Waterworks | Body | No | 1/4 Turn ceramic disk | Plastic Backnuts | Aerator | Click Type | Interconnecting Hoses, |
| BLS220 | Various | 1/2 | 6Bar bar | 65 °C | Waterworks | Body | No | 1/4 Turn ceramic disk | Plastic Backnuts | Aerator | Click Type | Interconnecting Hoses, |
| BLS230 | Various | 1/2 | 6Bar bar | 65 °C | Waterworks | Body | No | 1/4 Turn ceramic disk | Plastic Backnuts | Aerator | Click Type | Interconnecting Hoses, |
| BLS22A | Various | 1/2 | 6Bar bar | 65 °C | Waterworks | Body | No | 1/4 Turn ceramic disk | Plastic Backnuts | Aerator | Click Type | Interconnecting Hoses, |
| BLS22B | Various | 1/2 | 6Bar bar | 65 °C | Waterworks | Body | No | 1/4 Turn ceramic disk | Plastic Backnuts | Aerator | Click Type | Interconnecting Hoses, |
| BLS22C | Various | 1/2 | 6Bar bar | 65 °C | Waterworks | Body | No | 1/4 Turn ceramic disk | Plastic Backnuts | Aerator | Click Type | Interconnecting Hoses, |
| BLS22D | Various | 1/2 | 6Bar bar | 65 °C | Waterworks | Body | No | 1/4 Turn ceramic disk | Plastic Backnuts | Aerator | Click Type | Interconnecting Hoses, |
| BLS22E | Various | 1/2 | 6Bar bar | 65 °C | Waterworks | Body | No | 1/4 Turn ceramic disk | Plastic Backnuts | Aerator | Click Type | Interconnecting Hoses, |
| BLS24A | Various | 1/2 | 6Bar bar | 65 °C | Waterworks | Body | No | 1/4 Turn ceramic disk | Plastic Backnuts | Aerator | Click Type | Interconnecting Hoses, |
| BLS24B | Various | 1/2 | 6Bar bar | 65 °C | Waterworks | Body | No | 1/4 Turn ceramic disk | Plastic Backnuts | Aerator | Click Type | Interconnecting Hoses, |
| BLS24C | Various | 1/2 | 6Bar bar | 65 °C | Waterworks | Body | No | 1/4 Turn ceramic disk | Plastic Backnuts | Aerator | Click Type | Interconnecting Hoses, |
Finishes available: Chrome, Brass, Burnished Brass, Burnished Nickel, Matte Nickel, Copper, Dark Brass, Vintage Brass, Gold, Matte Gold.
Range of wall mounted spouts (plastic body). The outlet incorporates a plastic flow straightener. This product has not been tested or approved for claims of sterile properties made by the approval holder. Maximum operating temperature 60.0°C.
Range of stainless steel axial expansion joints (various end connections - see model). Maximum operating pressure 16.0 bar. Maximum operating temperature 100°C.
Range of Chlorine Dioxide dosing systems supplied with a stub flange and tee fitting. Maximum operating pressure 15.0 bar. Cold water use only.
‘Center Pot’ range of expansion vessels. Maximum working pressure 10.0 bar. Maximum operating temperature 70°C.
FLOWTECH range of fusion welded, PP-RCT fittings for use with Atlas PP-RCTGF pipe. Maximum working pressure 10.0 bar. Maximum operating temperature 85°C.
Range of solder ring copper fittings for use with copper tube to EN 1057. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Solder ring brass fittings for use with copper tube (manufactured to EN 1057). Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Range of brass fittings with compression connections to be used with copper pipes EN 1057. For above ground use only. Maximum working pressure 6.0 bar. Maximum operating temperature 95°C.
Page 211 of 233
We use cookies to give you the best possible experience with WRAS. Some are essential to provide website functions and ensure the website is secure. We also use cookies to help us understand how people use the site and to make improvements. Click "Accept All" to enable recommended settings or click "Manage cookies" to adjust your settings. For more details, see our Cookie Policy.
