Wall mounted hose union tap (DZR brass body) incorporating a non-rising spindle headwork with a butterfly handle operating member. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Range of wall mounted hose union taps with brass bodies incorporating a rising spindle headwork with a T - handle operating member. Model HC-20252-15 incorporates a lockshield device at the base of the operating stem. The spout outlets incorporate a hose union connector. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
502 series of automatic air venting valves with brass bodies, plastic float and EPDM ‘O’-rings. For non-potable water use only. Maximum working pressure 10.0 bar. Maximum operating temperature see models.
Range of wall mounted thermostatic blending valves (chromium plated brass) incorporating quarter turn ceramic disc headwork and a two-way, half-turn ceramic disc manual diverter for dual outlet models. The inlets incorporate a stainless-steel strainer & an approved check valve cartridge however, the complete product has not been fully tested to demonstrate it provides backflow protection. Maximum working pressure 5.0 Bar Maximum operating temperature 60.0°C
Range of wall mounted thermostatic blending valves (chrome plated brass), incorporating a half turn ceramic disc headworks (see models). The temperature is controlled independently via a thermostatic cartridge incorporating a manual override button, with a variety of operating members. The inlets incorporate approved check valve cartridges; however, the complete product has not been fully tested to demonstrate it provides backflow protection with stainless-steel strainers. Maximum working pressure 5.0 Bar.
Range of pressure relief valves with DZR brass bodies incorporating EPDM diaphragms. The valves are pre-set as follows: 311560, 312469, 312461ITH, 311461CTS,531661 CST models: 6.0 bar, 312471 CST model: 7.0 bar, 312020 CST model: 10.0 bar. Maximum operating temperature 99°C.
Range of pre-set pressure relief valves incorporating DZR brass bodies and an EPDM diaphragms and PTFE washers. The valve is fitted with hand operated rotating easing gear. Maximum working – see model. Maximum operating temperature 85°C
Range of lever or butterfly operated spherical valves with brass or nickel plate bodies and ball. Maximum working pressure 40.0 Bar Maximum operating temperature 99.0°C
Range of spherical valves with stainless steel bodies, incorporating PTFE seats and a lever t operating member. Maximum working pressure: 68 Bar. Maximum operating temperature: 100°C
Range of screwdriver operated spherical valves with a brass body and either a chrome plated brass ball (4000120555 model) or brass ball (all other models). Maximum working pressure 10.0 bar. Maximum operating temperature 100°C.
Range of non-rising spindle lock shield gate valves with DZR brass bodies. Maximum working pressure 16 bar. Maximum operating temperature: 65°C Maximum working pressure 10 bar. Maximum operating temperature: 82°C
Range of gate valves with brass bodies and wedges. Maximum working pressure 17.5 bar. Maximum operating temperature 93°C
Range of gate valves with brass bodies, brass wedges and PTFE seals. The valves operate via a non-rising spindle and are supplied with either no operating member or a hand wheel (see models) Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Range of gate valves with brass bodies, brass wedges and PTFE gaskets. The valves are operated via a non-rising spindle with a hand wheel operating member. The Z2020.028 compression model is for use with copper pipe (manufactured to EN1057). Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Range of gate valves with a non-rising spindle with a handwheel operating member or lockshield connection. Brass body and brass wedge. For use with copper pipe (manufactured to EN1057). Maximum working pressure 16.0 bar.
Non-metallic materials and components comply with BS6920 at 85°C
Range of screw down valves with brass or DZR brass bodies, brass or DZR brass bonnets, EPDM washers and PTFE seats. Compression connection to be used with copper pipe manufactured to EN1057. Maximum working pressure 16 bar. Maximum operating temperature 85°C.
Range of compression stop valves incorporating brass bodies, rising spindle headworks and EPDM gaskets. For use with copper pipe manufactured to BS EN 1057 (15mm, 22mm and 28mm) or PE pipe manufactured to BS EN 12201-2 (20mm and 25mm). Maximum working pressure 10.0 bar. Cold water use only.
Range of push-fit, screw down stop valves with plastic bodies for use with copper pipe (manufactured to EN1057), PEX pipe (manufactured to BS 7291-3) and/or MDPE pipe (manufactured to EN 12201 (inserts required). For above and below ground use. Maximum working pressure:16.0 bar Maximum operating temperature: 20.0°C.
‘NMSP2104 M & ER2104A01SM'. The following coatings were added to the approval in March 2025: ER2209A01SC, ER2252A01SC, ER2259A01SC & ER2260A01SC. Factory applied, blue coloured, porcelain (vitreous) enamel coatings. Apply as per manufacturer’s user manual 'PEM 38', edition '01' dated '14/10/2020'. Cure for 5 minutes@840°C. For use with water up to 85°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
‘PMSP5099-M & EP5099D01SC'. Factory applied, blue coloured, porcelain (vitreous) enamel coatings. Apply as per manufacturer’s user manual 'PEM 37', edition '01' dated '14/10/2020'. Cure for 5 minutes@840°C. For use with water up to 85°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
‘NMSP2104 M'. Factory applied, blue coloured, porcelain (vitreous) enamel coatings. Apply as per manufacturer’s user manual ‘specification no. PIN-10’, revision no. '0' dated '15/10/2020'. Cure for 5 minutes@840°C. For use with water up to 85°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Nylon 11'. Factory applied nylon coatings available in white or grey colours. The substrate the coating is to be applied to is heated to 310°C for 30 minutes and the coating applied as per manufacturer's work instructions 'WI-09-19 Rev. 6' dated April 22, 2020. Cure for 10 minutes@270°C. The white coating is for use with water up to 23°C. The grey coating is for use with water up to 85°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'SWEP Sealix Coating'. Factory applied, colourless (translucent) silicon dioxide coating. Apply as per manufacturing instructions ref. 'Sealix-2020-01' dated 2020-01-01. Cure for 3 hours@300°C. For use with water up to 85°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'EB-1003'. Factory applied, blue coloured epoxy powder coating. Apply and cure as per manufacturer's instructions 'Fowry Powder-001' dated '2020.3.20'. For use with water up to 85°C.
'Resicoat PI Brown'. Factory applied, brown coloured epoxy coating. Apply as per manufacturers datasheet dated March 4, 2020. Post-cure for 20 minutes@210°C. For use with water up to 23°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'EPY2-II'. Factory applied, blue coloured epoxy powder coating. Apply as per manufacturer's user instruction 'REV-202012-2' dated '11.12.2020'. Cure for 7 minutes@180°C. For use with water up to 65°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'PMSP5112-M, PMSP5113-M, PMSP5114-M, PMSP5115-M, EP5112D01SC, EP5113D01SC, EP5114D01SC & EP5115D01SC'. Factory applied, blue coloured, Porcelain Vitreous Enamel coatings. Apply as per manufacturer's User Manual 'PEM 37', 'Edition 01', dated '14/10/2020'. Cure for 5 minutes@840°C. For use with water up to 85°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'NMSP2251M, NMSP2265M, NMSP2266-M, NMSP2267-M, ER2251A01SM, ER2265A01SM, ER2266A01SC, ER2267A01SC'. Factory applied, blue coloured, Porcelain Vitreous Enamel coatings. Apply as per manufacturer's User Manual 'PEM 38', 'Edition 01', dated '14/10/2020'. Cure for 5 minutes@840°C. For use with water up to 85°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Ever-Blue'. Factory applied, blue coloured epoxy powder coating. Spray apply coating when substrate is at a temperature of between 180°C & 190°C as per manufacturer's TDS '20200801 A2', dated '09-10-2025'. Cure for 10 minutes@200°C. For use with water up to 85°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'SC3 Blue PTFE Coating'. Blue coloured, factory applied, PTFE coating intended to coat 'O' rings. Apply and cure as per manufacturer's instructions 'LDAP-007 issue 1' dated 11/02/2020. For use with water up to 85°C.
'Polyglass VEF'. Factory applied, two-part, off-white coloured, vinyl ester coating. Mix parts A & B in a 98:2 mass ratio and apply as per manufacturer's instructions '2/23' last reviewed July 2020. Cure for 7 days@21°C. For use with water up to 23°C. This material is only approved for the mixing & curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
‘Corroless ACO Brush Grades RAL5005 (GB861) and Light Green (GB206)’ (formerly known as 'Acothane Brush Grades Blue & Green'). Site applied, blue or green coloured, two-part polyurethane coatings consisting of an amber coloured, liquid activator and blue or green coloured coating. Mix brush grade and activator in a 3.24:1 weight ratio. Apply as per technical data sheet dated Feb 2020. Cure for 14 days@7°C. For use with water up to 23°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mix and cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
‘Sika MonoTop®-1010’, one-part cementitious bonding primer for use with ‘Sika MonoTop®-615’ one-part cementitious repair mortar. Mix ‘Sika MonoTop®-1010’ with tap water in the ratio of 25kg:5.25 litres. Apply as per manufacturer’s Product Data Sheet ‘020302020010000054, March 2021, Version 01.01’. Mix ‘Sika MonoTop®-615’ with tap water in the ratio of 25kg:3.8 litres and apply immediately to ‘Sika MonoTop®-1010’ as per manufacturer’s Product Data Sheet ‘020302040030000198, December 2021, Version 02.02’. Cure for 21 days@7°C. For use with water up to 23°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
Range of wedge shoes (part numbers 2005036, 2006536, 2008036, 2010036, 2012536, 2015036, 2020036, 2025036, 2030036, 2040036, 2650036, 2660036, 40005036, 40006536, 40008036, 40010036, 40015036, 40020036, 40025036, 2680036 & 126100036). Black coloured, injection moulded nylon wedge shoes. For use with water up to 50°C.
‘ME2020’ injection moulded components. Silicone rubber ‘O’ rings and gaskets available in red, blue, white, black, light grey colours. Shore hardness between 30 - 70. Tested in-radii sizes between 0.5mm and 5mm. For use with water up to 85°C.
Range of brass press fittings for use with MLC PE-RT/AL/PE-RT pipe. Maximum operating pressure 10 bar. Maximum operating temperature 80°C
RWC range of polypropolene fittings for use with PE pipe (manufactured to EN 12201). Maximum working pressure 16 bar. Cold water use.
Range of copper press fittings (‘M’ type crimp profile) and brass threaded adaptor fittings, for use with copper pipe (manufactured to EN1057). Maximum working pressure and operating temperatures: 16.0 bar @ 30°C and 10.0 bar @ 95°C.
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| 13.20205.G15.CP03-8510 | Chromed | BSP 1/2" (M) | 16 bar | 85 °C | Company logo (V&G), WRAS, size, production date (MM-YY) | Body | No | ||||
| 13.20205.G15.CP5R-8510 | BSP 1/2" (M) | 16 bar | 85 °C | Company logo (V&G), WRAS, size, production date (MM-YY) | Body | No | |||||
| 13.20205.G15.CP5R-8511 | BSP 1/2" (M) | 16 bar | 85 °C | Company logo (V&G), WRAS, CR, size, production date (MM-YY) | Body | No | |||||
| 13.20205.G20.CP03-8510 | Chromed | BSP 3/4" (M) | 16 bar | 85 °C | Company logo (V&G), WRAS, size, production date (MM-YY) | Body | No | ||||
| 13.20205.G20.CP5R-8510 | BSP 3/4" (M) | 16 bar | 85 °C | Company logo (V&G), WRAS, size, production date (MM-YY) | Body | No | |||||
| 13.20205.G20.CP5R-8511 | BSP 3/4" (M) | 16 bar | 85 °C | Company logo (V&G), WRAS, CR, size, production date (MM-YY) | Body | No | |||||
| 13.20245.A15.CP5R-8510 | BSP 1/2" (M) | 16 bar | 85 °C | Company logo (V&G), WRAS, size, production date (MM-YY) | Body | No | |||||
| 13.20245.A20.CP5R-8510 | BSP 3/4" (M) | 16 bar | 85 °C | Company logo (V&G), WRAS, size, production date (MM-YY) | Body | No | |||||
| 13.20255.G15.CP03-8510 | Chromed | BSP 1/2" (M) | 16 bar | 85 °C | Company logo (V&G), WRAS, size, production date (MM-YY) | Body | No | ||||
| 13.20255.G15.CP5R-8510 | BSP 1/2" (M) | 16 bar | 85 °C | Company logo (V&G), WRAS, size, production date (MM-YY) | Body | No | |||||
| 13.20255.G15.CP5R-8511 | BSP 1/2" (M) | 16 bar | 85 °C | Company logo (V&G), WRAS, CR, size, production date (MM-YY) | Body | No | |||||
| 13.20275.G15.CP5R-8510 | BSP 1/2" (M) | 16 bar | 85 °C | Company logo (V&G), WRAS, size, production date (MM-YY) | Body | No | |||||
| 13.20305.G15.CP03-8510 | Chromed | BSP 1/2" (M) | 16 bar | 85 °C | Company logo (V&G), WRAS, size, production date (MM-YY) | Body | No | ||||
| 13.20305.G15.CP5R-8510 | BSP 1/2" (M) | 16 bar | 85 °C | Company logo (V&G), WRAS, size, production date (MM-YY) | Body | No | |||||
| 13.20305.G15.CP5R-8511 | BSP 1/2" (M) | 16 bar | 85 °C | Company logo (V&G), WRAS, CR, size, production date (MM-YY) | Body | No | |||||
| 13.20305.G20.CP03-8510 | Chromed | BSP 3/4" (M) | 16 bar | 85 °C | Company logo (V&G), WRAS, size, production date (MM-YY) | Body | No | ||||
| 13.20305.G20.CP5R-8510 | BSP 3/4" (M) | 16 bar | 85 °C | Company logo (V&G), WRAS, size, production date (MM-YY) | Body | No | |||||
| 13.20305.G20.CP5R-8511 | BSP 3/4" (M) | 16 bar | 85 °C | Company logo (V&G), WRAS, CR, size, production date (MM-YY) | Body | No | |||||
| 13.20365.G15.CP03-8510 | Chromed | BSP 1/2" (M) | 16 bar | 85 °C | Company logo (V&G), WRAS, size, production date (MM-YY) | Body | No | ||||
| 13.20365.G15.CP5R-8510 | BSP 1/2" (M) | 16 bar | 85 °C | Company logo (V&G), WRAS, size, production date (MM-YY) | Body | No | |||||
| 13.20365.G15.CP5R-8511 | BSP 1/2" (M) | 16 bar | 85 °C | Company logo (V&G), WRAS, CR, size, production date (MM-YY) | Body | No |
Range of stainless steel braided, EPDM lined flexible hose assemblies with DZR brass end connections. Maximum working pressure 10.0 bar. Maximum operating temperature 85°C
Range of gate valves with either brass or DZR brass bodies. The valves incorporate non-rising spindle headworks with a wheel type operating member. Maximum working pressure 16.0 Bar. Maximum operating temperature 85.0°C.
Range of screw down stop valves incorporating brass or DZR brass bodies. The valves are to be used with copper pipe (manufactured to EN1057). Maximum working pressure 16 Bar. Maximum operating temperature 85°C.
'Dicoat Medium Temp Black'. Factory applied, black coloured bitumen coating. Apply at a Relative Humidity of below 60% as per manufacturer's user instructions reference 'SPL/RD/UI/2019100121', issue no. '01' dated 08.07.2020. Cure for 7 days@30°C. For use with water up to 23°C. This material is only approved for the RH & curing conditions that appear on the approval. If the RH and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'JSP/SF-Blue'. Factory applied, blue coloured epoxy powder coating. Spray apply coating when substrate is at a temperature of between 180°C & 190°C as per manufacturer's TDS '20200801 A2', dated '09-10-2025'. Cure for 10 minutes@200°C. For use with water up to 85°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'YS-01 Powder Coating'. Factory applied, blue coloured epoxy powder coating. Apply as per manufacturer's instruction document 'HJ-Q-SOP-05' dated 2020-1-10. Cure for 10 minutes@200°C. For use with water up to 85°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'XX-CM1'. Factory applied, grey coloured cement mortar. Mix cement, sand, and water in a volume ratio of 1:2.0:0.4 and apply as per manufacturer's safety data sheet 'A1: 26-01-2020'. Cure for 5 hours@30°C and then steam cure for 6 hours@30°C. For use with water up to 65°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified then the material is not covered by the scope of the approval.
'POLYNT 1349 TAEQ20 to be used in conjunction with POLYCOR LP PA FC CLEAR 0200'. POLYNT 1349 TAEQ20 is a polyester resin and LP PA FC CLEAR 0200 is a factory applied, gel coat (when used together the material appears light pink in colour). Apply as per manufacturer's TDS ‘7206 Version: 0, 19/11/2020’. Cure for 24 hours@25°C. For use with water up to 23°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
Page 3 of 3
We use cookies to give you the best possible experience with WRAS. Some are essential to provide website functions and ensure the website is secure. We also use cookies to help us understand how people use the site and to make improvements. Click "Accept All" to enable recommended settings or click "Manage cookies" to adjust your settings. For more details, see our Cookie Policy.
