`TUB05`. Extruded, dual layered hose consisting of a clear PE liner and black coloured EPDM outer layer. Shore hardness 85. For use with water up to 85°C.
'EP12/2/5 BLK 'O'-rings & seals'. Black coloured, injection moulded EPDM 'O' rings & seals. Shore hardness 50. The ‘O’ rings have a tested in-radius size of 1.0mm. The seals have a tested in-radius size of 0.75mm. For use with water up to 85°C.
‘4280’ black coloured injection moulded EPDM rubber components. Shore hardness 80. '4280 Membrane' has a tested in-radius size of 1.75mm. ‘4280 ’O’ rings’ have a tested in-radius size of 1.31mm. ‘4280 washers’ have a tested in-radius size of 1.05mm. All components are for use with water up to 85°C.
'GDE 7133', black coloured, compression moulded EPDM 'O' ring with a tested in-radius size of 2.0mm. In March 2025, ‘KD S-Ring’. black coloured, compression moulded EPDM seal with a tested in-radius size of 0.95mm was added to the approval. Both components have a shore hardness 70 and are for use with water up to 85°C.
'XGM050'. Black coloured, compression moulded EPDM rubber gaskets manufactured from raw material '70802'. Shore hardness 80. Tested in-radius size 2.5mm. For use with water up to 85°C.
'4360 'O' rings, washers, membranes and lip seals'. Black coloured, injection moulded EPDM components with a shore hardness of 60. The ‘O’ rings have a tested in-radius size of 1.31mm. The washers have a tested in-radius size of 1.05mm. The membranes have a tested in-radius size of 1.55mm. The lip seals have a tested in-radius size of 0.40mm. For use with water up to 85°C.
'7EP1197 Gasket'. Black coloured, extruded EPDM gasket. Shore hardness 70. Tested in-radius size 0.5mm. '7EP1197 'O'-rings' were added to the approval in March 2023. Black coloured, injection moulded EPDM 'O'-rings. Shore hardness 70. Tested in-radius size 0.9mm. For use with water up to 85°C.
'KEP EPDM Butterfly Valve Seat'. Black coloured, compression moulded EPDM sheet. Shore hardness 70. Tested in-radius size 1.6mm. For use with water up to 23°C.
'EP0B7070C 'O' rings'. Black coloured, compression moulded EPDM 'O' rings. Shore hardness 70. Tested in-radius size between 0.5mm & 3.5mm. For use with water up to 23°C.
'D0012'. Black coloured, EPDM rubber material manufactured by vulcanised moulding. Shore hardness 70. Tested in-radius size 1.0mm. For use with water up to 85°C.
'HW-EPDM SH 50'. Black coloured, compression moulded EPDM rubber material. Shore hardness 50. Tested in-radius size 1.0mm. For use with water up to 65°C.
'EP01961PWRC'. Black coloured, compression moulded EPDM material. Shore hardness 60. Tested in-radius size 1.0mm. For use with water up to 85°C.
'CVE78'. Black coloured, extruded EPDM material. Shore hardness 80. Tested in-radius size 10.0mm. For use with water up to 23°C.
‘EWA 12150 (EW48) Rev.1. EWA 12155A (EP55) Rev.1. EWA 12160A (EW 60) Rev.1. EWA 12165 (EW65 2GS) Rev.1. EWA 12170 (WRC 70) Rev.1. EWA 12175 (WRC 75) Rev.1. EWA 12180 (EW80) Rev.1’. Black coloured, compression moulded, EPDM sheet materials. Shore hardness between 50 & 80. Tested in-radius size 1.2mm. For use with water up to 85°C.
'EPH-70'. Black coloured, injection moulded EPDM material. Shore hardness 70. Tested in-radius size 1.0mm. For use with water up to 85°C.
‘KRE 60 (103), KRE 65 (100) & KRE 65 (106)’. In September 2022 ‘KRE 60 (104)’ was added to the approval. Black coloured, compression moulded EPDM rubber materials. Shore hardness 60 & 65. Tested in-radius size 1.0mm. For use with water up to 60°C.
'TIMO 3-70'. Black coloured, injection moulded EPDM material. Shore hardness 70. Tested in-radius size 1.2mm. For use with water up to 85°C.
'EX60LC, EX70LC & EX80LC'. Black coloured, compression moulded EPDM rubber materials. Shore hardness 60, 70 & 80. Tested in-radius size 1.2mm. For use with water up to 85°C.
'HT5697-5'. Black coloured, injection moulded EPDM material. Shore hardness 67. Tested in-radius size 1.0mm. For use with water up to 50°C.
Black coloured, compression moulded EPDM materials with a tested in-radius size of 1.3mm. 'EPW-50, EPW-55, EPW-60, EPW-65, EPW-70 & EPW-75' have a shore hardness of between 50 & 75 and are for use with water up to 23°C. ‘EPW-80' has a shore hardness of 80 and is suitable for use with water up to 85°C.
'EH600-151'. Black coloured, compression moulded EPDM material. Shore hardness 60. Tested in-radius size 1.0mm. For use with water up to 85°C.
'H600042'. Black coloured, compression moulded EPDM material. Shore hardness 70. Tested in-radius size 1.3mm. For use with water up to 65°C.
'Hongli IRHD 70'. Black coloured, press moulded EPDM material. Shore hardness 70. Tested in-radius size 1.09mm. For use with water up to 23°C.
‘EWA 12150 (EW48) Rev.1. EWA 12155A (EP55) Rev.1. EWA 12160A (EW 60) Rev.1. EWA 12165 (EW65 2GS) Rev.1. EWA 12170 (WRC 70) Rev.1. EWA 12175 (WRC 75) Rev.1. EWA 12180 (EW80) Rev.1’. Black coloured, compression moulded, EPDM sheet materials. Shore hardness between 50 & 80. Tested in-radius size 1.2mm. For use with water up to 85°C.
‘SBPEP4555 (50), SBPEP55 (55), SBPEP60 (60), SBPEP65 (65), SBPEP70 (70), SBPEP75 (75) & SBPEP7085 (80)’. Black coloured, compression moulded EPDM rubber sheet materials with a shore hardness of between 50 & 80. Tested in-radius size of 1.0mm. For use with water up to 60°C.
'E6083AA'. Black coloured, compression moulded EPDM material. Shore hardness 60. Tested in-radius size 1.0mm. For use with water up to 85°C.
'EPDM C12251'. Black coloured, compression moulded, EPDM rubber material. Shore hardness 77. Tested in-radius size 12.5mm. For use with water up to 23°C.
'EP601289C'. Black coloured, compression moulded EPDM material. Shore hardness 60. Tested in-radius size 1.0mm. For use with water up to 85°C.
'KRE70 (80-3)'. Black coloured, compression moulded EPDM material. Shore hardness 70. Tested in-radius size 1.0mm. For use with water up to 60°C.
'EP6007K'. Black coloured, compression moulded EPDM material. Shore hardness 60. Tested in-radius size 1.0mm. For use with water up to 85°C.
Range of stop valves with plastic bodies and an EPDM diaphragm. The valves are operated via a switch located on the valve. The RCL and RPL models can also be operated by a remote switch. The product incorporates a plastic strainer central to the body. All valves are for use with copper pipe (manufactured to BS EN 1057). The PL suffix valves are also for use with PEX pipe (manufactured to BS7291-3). Models added Jan 2025 are for use with PE80 & PE100 pipes manufactured to BS EN 12201:2 at the inlets and the outlets are suitable for PEX pipe manufactured in accordance with BS7291 and copper pipe manufactured in accordance with BS EN 1057. For above ground use only. Maximum working pressure 10.0 bar. Cold water use only.
'VRSY6090 + Nylon 6.6 Rubber Expansion Joint'. Black coloured, compression moulded composite rubber expansion joint which consists of chlorobutyl/EPDM rubber & embedded polyamide fabric. Shore hardness 55. Tested in-radius size 2.0mm. For use with water up to 23°C.
'ERV-R & ERP Rubber Expansion Joints'. Black coloured, compression moulded composite rubber expansion joint which consists of chlorobutyl/EPDM rubber & embedded polyamide fabric. The `ERV-R` joint has a red coloured band on the exterior and the `ERP` joint has a red coloured dot on the exterior. Shore hardness 55. Tested in-radius size 2.0mm. For use with water up to 23°C.
'STENFLEX® Butyl Rubber Expansion Joint'. Black coloured, compression moulded composite rubber expansion joint which consists of chlorobutyl/EPDM rubber & embedded polyamide fabric. Shore hardness 55. Tested in-radius size 2.0mm. For use with water up to 23°C.
Spring loaded resilient trim check valve cartridge with a plastic body and EPDM ‘O’-rings. For insertion into fittings with specifically sized bores. Maximum working pressure 10.0 Bar. Maximum operating temperature 85°C
Spring loaded resilient trim in-line check valve cartridge with acetal body, incorporating a stainless steel spring and NBR or EPDM ‘O’-rings. To be housed in a specifically dimensioned bores. Maximum working pressure 16.0 bar. Maximum operating temperature 65°C for 31.4232.0; 85°C for 31.0030.0.
Spring loaded resilient trim in-line check valve cartridge with acetal body, incorporating a stainless steel spring, EPDM & silicone ‘O’-rings. To be housed in a specifically dimensioned body. Maximum working pressure 14 Bar
Non-metallic materials and components comply with BS6920 at 85°C
Range of spring loaded resilient trim check valve cartridges with acetal body and EPDM `O`-ring. For insertion into specifically dimensioned bores. Maximum working pressure 16 Bar.
Non-metallic materials and components comply with BS6920 at 85°C
Range of flow restrictors with plastic bodies and EPDM ‘O’-rings available in a variety of colours (see models). Maximum operating temperature 60°C.
Range of ceramic cartridge headwork with plastic bodied and EPDM ‘O’ rings for insertion into specifically dimensioned bores. Maximum working pressure 12.0 bar.
Non-metallic materials and components comply with BS6920 at 80°C
Range of thermostatic cartridges with EPDM ‘O’-rings and stainless-steel filters, to be installed into specifically dimensioned bodies. Maximum operating temperature - 75°C
Range of thermostatic cartridges with brass or plastic bodies (see model) incorporating a stainless-steel strainer and EPDM ‘O’-rings. Maximum working pressure 10.0 Bar. Temperature: 75°C – GR-FX-X05S, GR-FX-01S, GR-FX-13T & GR-FX-X08. 65°C - GR-FX-04S & GR-FX-02TF.
Floor mounted two hole, single outlet (fixed) combination tap assembly (chromium plated brass) incorporating ¼ turn ceramic disc headworks with single lever operating members and a self-cancelling diverter to shower outlet. The spout outlet incorporates a plastic flow straightener, NBR washer with stainless steel strainer. The product is supplied with a stainless steel inter-locked shower hose with EPDM lining & handset. Maximum working pressure 10.0 bar. Maximum operating temperature 65°C.
Range of deck mounted two hole, single outlet (fixed) combination tap assemblies (chromium plated brass), incorporating ¼ turn ceramic disc headworks with single lever operating members and a self-cancelling diverter to shower outlet. The spout outlet incorporates a plastic flow straightener and a NBR washer with a stainless steel strainer. The products are supplied with metal backnuts, stainless steel inter-locking shower hoses with EPDM lining and handsets. Maximum working pressure 10.0 Bar. Maximum operating temperature 65°C.
Range of deck mounted two hole, single outlet (fixed) combination tap assemblies (chromium plated brass), incorporating ¼ turn ceramic disc headworks with single lever operating members and a self-cancelling diverter to shower outlet. The spout outlet incorporates a plastic flow straightener and a NBR washer with a stainless steel strainer. The products are supplied with metal backnuts, stainless steel inter-locking shower hoses with EPDM lining and handsets. Maximum working pressure 10.0 Bar. Maximum operating temperature 65°C.
Floor mounted two hole, single outlet (fixed) combination tap assembly (chromium plated brass) incorporating ¼ turn ceramic disc headworks with single lever operating members and a self-cancelling diverter to shower outlet. The spout outlet incorporates a plastic flow straightener, NBR washer with stainless steel strainer. The product is supplied with a stainless steel inter-locked shower hose with EPDM lining & handset. Maximum working pressure 10.0 bar. Maximum operating temperature 65°C.
Range of deck mounted two hole, single outlet (fixed) combination tap assemblies (chromium plated brass), incorporating ¼ turn ceramic disc headworks with single lever operating members and a self-cancelling diverter to shower outlet. The spout outlet incorporates a plastic flow straightener and a NBR washer with a stainless steel strainer. The products are supplied with metal backnuts, stainless steel inter-locking shower hoses with EPDM lining and handsets. Maximum working pressure 10.0 Bar. Maximum operating temperature 65°C.
Deck mounted two-hole, single outlet, fixed combination tap assembly (chrome plated brass) incorporating a quarter turn ceramic disc headwork with a single lever operating member. The temperature is controlled independently via a thermostatic cartridge incorporating a single lever operating member and a manual override button. The spout outlet incorporates a lockable diverter to shower outlet and a plastic aerator. The inlets incorporate EPDM washers and approved check valve cartridges, (however, the complete product has not been fully tested to demonstrate it provides backflow protection). Maximum operating pressure 5.0 bar
Non-metallic materials and components comply with BS6920 at 60°C
Range of deck mounted, three-hole, single outlet (fixed) combination tap assemblies (brass body, various finishes - see model), incorporating quarter turn ceramic disc headworks with single lever operating members. The outlets of the side valves each incorporate a combined EPDM washer and stainless-steel strainer and a brass adaptor, which connects to the spout via two stainless steel braided PEX lined quick connect hoses and a plastic Y-piece. The spout outlet is supplied by a brass inlet pipe which incorporates a plastic flow regulator, as well as a stainless steel braided PEX lined flexible hose assembly. The spout outlet incorporates a plastic aerator. The products are supplied with a pop-up waste. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.
Range three hole, single outlet (swivel) combination tap assemblies (brass bodies, various finishes – see model). Incorporating quarter turn ceramic disc headworks and various operating members. The spout outlets incorporate plastic aerators. The product incorporates ACB braided EPDM lined flexible connection hose assemblies incorporating M10 x ½” BSP (F) captive nut end connections. Maximum working pressure 5.0 bar. Maximum operating temperature 60°C.
Page 17 of 45
We use cookies to give you the best possible experience with WRAS. Some are essential to provide website functions and ensure the website is secure. We also use cookies to help us understand how people use the site and to make improvements. Click "Accept All" to enable recommended settings or click "Manage cookies" to adjust your settings. For more details, see our Cookie Policy.
