'RELIBIT 1001 Coating'. Factory applied, black coloured bitumen coating. Apply as per manufacturer's Standard Operating Procedure & Guidelines 'RP/291', '203/2024, Revision 1', dated '1st April 2024'. Cure for 10 hours@35°C. For use with water up to 23°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'ZCGJ-2025'. Factory applied, grey coloured Portland Cement Mortar. Mix cement, sand and water in a 2:1:0.4 mass ratio and apply as per manufacturer's instructions issue 'ZC02250725' dated '2025.7.25'. Cure for 12 hours@55°C. For use with water up to 65°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the materials are not covered by the scope of the approval.
'ZC-2025HSR'. Factory applied, grey coloured sulphate resistant cement. Mix cement:sand:water in a 1.5:1:0.4 mass ratio and apply as per manufacturer's instructions 'ZC01250725', dated '2025.7.25'. Cure for 8 hours@23°C. For use with water up to 65°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Birla SRPC - Electrocement'. Factory applied, grey coloured, cement mortar. Mix cement, sand & water in a mass ratio of 0.6:1.0:0.22 and apply as per manufacturer's Work Instructions 'WP-08-05 I', Issue '04', Revision '0', dated '22.08.2024'. Cure for 24 hours@27°C. For use with water up to 60°C. This material is only approved for the mixing & curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Hempaline Defend 430'. Factory applied, two-part, white coloured epoxy coating. Mix base and curing agent in a 4:1 volume ratio and apply as per manufacturer's PDS dated 'December 2024'. Cure for 7 days@20°C. For use with water up to 60°C. This material is only approved for the mixing & curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'8284873 HA002I INT 100 HYF WHITE SN80'. Factory applied, white coloured epoxy coating. Apply as per manufacturer's TDS 'Revision Date: V2, 24.05.2024', 'Region: EMEA'. Cure for 15 minutes@200°C. For use with water up to 85°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'GF30-NC024'. Light grey coloured, injection moulded, PA66+30%GF material. For use with water up to 85°C.
'LARTON G/40 NAT.:0169F1'. Brown coloured, injection moulded PPS material. For use with water up to 85°C.
'3P764921 Pipe Spacer'. White coloured (opaque), injection moulded PP Pipe Spacer. For use with water up to 85°C.
‘2KPS EX3 Light Pink' & ‘2KPS EX3 Grey'. Site applied, two-part (resin & hardener is automatically mixed in a 3:1 volume ratio through dispensing nozzle) anchor resins. Apply and cure as per ’T Load’ cures set out in Table B4 of European Technical Assessment ‘ETA 16/0884’, dated ‘22/04/2025’. For use with water up to 65°C. If the cure conditions are varied from those specified in ’T Load’ cures set out in set out in Table B3 of European Technical Assessment ‘ETA 16/0884’ then the materials are not covered by the scope of the approval. For use only as a resin anchor having been tested at a reduced surface area to volume ratio of 1,000mm² per 1 litre of water.
'DS MAX'. Site applied, two-part (supplied with internal mixing nozzle so no manual mixing required), brown coloured chemical anchor resin. Apply as per manufacturer's instructions 'Version 28', dated 03.04.2025. Cure for 4 days@5°C. For use with water up to 23°C. For use only as a resin anchor having been tested at a reduced surface area to volume ratio of 1,000mm² per 1 litre of water. This material is only approved for the mixing and curing conditions that appear on the approval. If the mix and cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
‘NS’. Site applied, grey coloured chemical anchor resin which is supplied in a pre-mixed cartridge. Apply as per manufacturer’s instructions 'Version 23.04.2025'. Cure for 4 days@7°C. For use with water up to 23°C. For use only as a resin anchor having been tested at a reduced surface area to volume ratio of 1,000mm² per 1 litre of water. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'CarboStop 102/CarboStop 102 ACC'. Site applied, cream coloured (once applied) waterstop. Mix CarboStop 102 resin and CarboStop 102 ACC accelerator in a weight ratio of 20:0.4. Apply and cure as per manufacturer's Application Guide, revision date '19/09/25'. For use with water up to 23°C. This material is for use in concrete reservoirs and similar structures, constructed in accordance with the design criteria of BS EN 1992 with respect to normal frequency of joints. The material has been tested at a reduced surface area to volume ratio of 1000mm² per litre as specified in BS 6920: Part 1. This material is only approved for the mixing & curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Weld-On 319 PVC Cement'. Clear Solvent Cement. Apply as per manufacturer's TDS '319-05-2024'. Cure for 4 hours@5°C. For use with water up to 23°C.
Range of floor standing, single hole, single outlet (fixed) combination tap assemblies, (brass bodies - various finishes), incorporating a ceramic cartridge headwork with a single lever operating member and a manual diverter to a shower outlet. The spout outlet incorporates a plastic aerator. Maximum working pressure 5 Bar Maximum operating temperature 65.0°C
Range of bottom entry BS1212-4 (2016) delayed or non delayed action type float operated valves for WC flushing cisterns. Maximum working pressure 10.0 Bar, cold water use only.
Range of side entry BS1212-4 (2016), delayed action or non-delayed action type float operated valves for WC flushing cisterns. The inlet incorporates an optional flow restrictor. Maximum working pressure 10.0 Bar Maximum operating temperature Cold water use only.
Wall hung concealed WC flushing cistern with a BS 1212-4 float operated inlet valve providing a Type AG air gap arrangement and a dual flush outlet valve. The flush volume is operated by a push button assembly. Maximum working pressure - 10 Bar. Cold water use only.
Range of WC flushing cistern incorporating a side entry compact type float operated inlet valve providing a Type AG air gap with a dual flush drop valve for full flush volumes of up to 6 litres and a reduced flush of up to 4 litres. The cistern is operated by a manual push button and incorporates a servicing valve on the inlet supply. Maximum working pressure 10.0 bar. Cold water use only.
Low Level WC suites incorporating a frame mounted ceramic pan that is fitted with a washing & drying arrangement which is fed via a type `AB` airgap (verified by test - suitable for backflow protection against fluid category 5). The cistern incorporates a side entry BS1212/4 float operated inlet valve and provides a type `AB` air gap. The drop type flush valve provides a single flush of 6 litres and is operated by elbow push button levers that are designed into the front of the cistern cover. Maximum working pressure 10.0 bar. Cold water use only
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| OASISBM | Chrome | 1/2" BSP (F) | 8 bar | 65 °C | Utopia | Body | No | Solenoid | Not Applicable | Aerator |
Range of combined bath fillers and overflow waste assemblies with plastic bodies (various finishes). The outlet incorporates a plastic aerator. The products are supplied with a cable operated pop-up waste. Maximum operating temperature 60°C.
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| T43014 | BSP 3/4" (F) | 10 bar | 85 °C | Company logo | On body | No | |||||
| T43084 | BSP 3/4" (F) | 10 bar | 85 °C | Company logo | On body | No | |||||
| T43064 | BSP 3/4" (F) | 10 bar | 85 °C | Company logo | On rear of body | No | |||||
| T43194 | BSP 3/4" (F) | 10 bar | 85 °C | Company logo | On rear of body | No | |||||
| T44014 | BSP 3/4" (F) | 10 bar | 85 °C | Company logo | On body | No | |||||
| T44054 | BSP 3/4" (F) | 10 bar | 85 °C | Company logo | On body | No | |||||
| T44034 | BSP 3/4" (F) | 10 bar | 85 °C | Company logo | On body | No | |||||
| T45004 | BSP 3/4" (F) | 10 bar | 85 °C | Company logo | On body | No | |||||
| T45014 | BSP 1/2" (F) | 10 bar | 85 °C | Company logo | On operating member | No |
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| TC28 | 27.98mm | 10 bar | 85 °C | WANHAI, WRAS, TC28, Production date (DD/MM/YYYY) | Body | No | |||||
| TC28-1 | 27.98mm | 10 bar | 85 °C | WANHAI, WRAS, TC28-1, Production date (DD/MM/YYYY) | Body | No |
Non-verifiable double check valve assembly with DZR brass body, incorporating two spring loaded, resilient trim in-line check valve cartridges. Compression connection to be used with copper pipe BS EN1057 only. Maximum working pressure 10.0 bar. Maximum operating temperature 85°C for 12.10102.035.CP5R-8511, Maximum operating temperature 65°C for 12.10112.035.CP5R-8511.
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| XDSV12 | BSP 1/2" (M) | 16 bar | 85 °C | Company logo | Body | No |
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| SL15TA90 (Plastic)Red | BSP 1/2" (M) | 16 bar | 85 °C | Hent, WRAS | Body | No | |||||
| SL15TA90 (Plastic)Blue | BSP 1/2" (M) | 16 bar | 85 °C | Hent, WRAS | Body | No |
Range of non-rising spindle headworks with brass bodies. For insertion into specifically dimensioned bodies. Maximum working pressure 10.0 bar. Maximum operating temperature 85°C.
Range of quarter turn ceramic disc headworks with brass bodies and EPDM `O` rings for insertion into specifically dimensioned bores. Maximum working pressure; 10 Bar Maximum operating temperature 85°C.
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| HW28C | 27.8mm | bar | 85 °C | WANHAI, WRAS, HW28C, Production date (DD/MM/YY) | Body | No |
Kisdon range of single hole single outlet (swivel) pull out spray combination tap assembly (chromium plated brass) with ¼ turn ceramic disc headwork and single lever operating members. The outlet of the pull-out spray incorporates a plastic flow aerator and an approved check valve cartridge however, the complete product has not been fully tested to demonstrate it provides backflow protection. Supplied with EPDM lined flexible hose assemblies. Maximum working pressure 10.0 bar. Maximum operating temperature 65°C.
Range of single-hole, single outlet (fixed) combination tap assemblies (brass bodies – various finishes), incorporating ceramic cartridge headworks with single lever operating members. The spout outlet incorporates a plastic aerator. The products are supplied with click type pop up waste (verified by test). Maximum working pressure 5.0 Bar. Maximum operating temperature 60°C
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Wastes | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|---|
| 818JK | Chrome | 1/2" BSP | 5.0 bar | 60 °C | Bristan | Handle | No | Ceramic cartridge | C-plate | Waterfall | Click Type |
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| TVW103006000XX | Various | ½” BSP (M) | 10 bar | 60 °C | Villeroy & Boch | On the lever | Yes | 1/4 Turn ceramic disk | Plastic Backnuts | Aerator | |
| TVW104002000XX | Various | ½” BSP (M) | 10 bar | 60 °C | Villeroy & Boch | On the lever | Yes | 1/4 Turn ceramic disk | Plastic Backnuts | Aerator |
XX at the end indicates the Finish of surfaces that are not in contact with water (61 - Chrome, K5 - Matt black, 76 - Brushed gold, 64 - Brushed nickel) The products were already tested according to the TCS. The report from SKZ is attached.
Range of single hole, single outlet (fixed) combination tap assemblies with (brass bodies - various finishes), incorporating a ceramic disc headwork with various type operating members. The spout outlet incorporates a plastic aerator. Product is supplied with click type pop-up waste – not verified by test. Maximum working pressure 6 Bar. Maximum operating temperature 65°C.
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| N SNK EF C | Chrome | 15mm | 5.0 bar | 60 °C | Bristan | Handle | No | 1/4 Turn ceramic disk | Not Applicable | Flow Straightener |
A single-hole single outlet swivel combination tap assembly with brass body (chromium plated). Incorporating ceramic cartridge headwork. The spout outlet incorporate a plastic aerator. Maximum working pressure - 10 bar. Maximum operating temperature - 60°C.
Range of single hole, single outlet (swivel) combination tap assemblies (brass bodies – various finishes), incorporating quarter turn ceramic disc headworks with single lever operating members. The spout outlet incorporates a plastic aerator or flow straightener. Maximum working pressure 10.0 bar.
Non-metallic materials and components comply with BS6920 at 65°C
Range of single hole, single outlet, swivel, combination tap assemblies (brass bodies - various finishes). Incorporating a ceramic cartridge headwork with various operating members. The spout outlet incorporates a plastic aerator. Model BLS4ZZX is supplied with a pop-up waste – not verified by test. Maximum working pressure 6.0 bar. Maximum operating temperature 65°C.
Range of single hole, single outlet (swivel) combination tap assemblies (brass bodies – various finishes). Incorporating quarter turn ceramic disc or ceramic cartridge headworks and single lever or cross top operating members. The spout outlets incorporate a plastic aerator. Maximum working pressure 5.0 Bar Maximum operating temperature 70.0°C.
Single hole, double outlet (swivel) combination tap assembly (chrome plated brass body). Incorporating a ceramic disc headworks and single lever operating members. The spout outlet incorporates a plastic aerator. Maximum working pressure 5.0 Bar Maximum operating temperature 70.0°C
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| AL 2TH WMBAS C | Chrome | 15mm compression | 5 bar | 65 °C | Bristan | Handle | No | Ceramic cartridge | Not Applicable | Aerator | Flow Regulator Fitted, |
| AL 2TH WMBAS BLK | Black | 15mm compression | 5 bar | 65 °C | Bristan | Handle | No | Ceramic cartridge | Not Applicable | Aerator | Flow Regulator Fitted, |
| AL 2TH WMBAS BB | Brushed Brass | 15mm compression | 5 bar | 65 °C | Bristan | Handle | No | Ceramic cartridge | Not Applicable | Aerator | Flow Regulator Fitted, |
Two hole, single outlet (fixed) combination tap assemblies (brass body, chrome finish), incorporating quarter turn ceramic disc headworks and single lever operating members. The products are supplied with metal backnuts. Maximum working pressure 10 bar. Maximum operating temperature 85°C
Two-hole, single outlet (fixed) combination tap assembly (chromium plated brass), incorporating quarter turn ceramic disc headworks and single lever operating members. The spout outlet incorporates a plastic flow straightener. The product is supplied with metal back nuts. Maximum working pressure 10.0 Bar.
Non-metallic materials and components comply with BS6920 at 65°C
Wall mounted, two-hole, single outlet (fixed) combination tap assemblies (chromium plated brass) incorporating a quarter turn ceramic disc headwork with dome type operating member. Temperature is controlled independently via thermostatic cartridge with single lever operating member. The inlets incorporate a stainless steel strainers and an approved check valve cartridge, however the complete product has not been fully tested to demonstrate It provides backflow protection. The spout outlets incorporate a plastic aerator. Maximum working pressure 8.0 bar. Maximum operating temperature 65°C.
Range of two hole, single outlet fixed combination tap assemblies (brass bodies – various finishes), incorporating a ceramic cartridge headwork and a lever type operating member. The spout outlet incorporates a plastic aerator. Maximum working pressure 10.0 Bar Maximum operating temperature 65.0°C
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| M33135 X XXX | VARIOUS | 3/4” BSP male inlet. | 10.0 bar | 65 °C | PPI | BODY | No | 1/4 Turn ceramic disk | Metal Backnuts | Flow Straightener | Shower Hose, Handset, |
| M4305 X XXX | VARIOUS | 3/4” BSP male inlet. | 10.0 bar | 65 °C | PPI | BODY | No | Non-rising spindle | Metal Backnuts | Flow Straightener | Shower Hose, Handset, |
X XXX Denotes the following: First X: Different handle option and the second, third & fourth XXX for different finishes: Handles: A, E or F – Dome, cross top or lever types Chrome – No suffix, brushed brass – BGP, PVD Gold – PVD, Brushed Nickel – BN1, Gun Metal – GMG, Matt Black – MBK, Matt White – MWH, Stainless Steel – SS1, Black Chrome – BCP, Titanium – TIB and Antique Bronze – AB1
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| F3068-** | Various | BSP 3/4" (M) | 10 bar | 60 °C | LANBIAO | Rear of body | No | Ceramic disk diverter | Metal Backnuts | Aerator | Flow Regulator Fitted, |
1)No Suffix-Chrome 2)-**Represents the following different surface treatments: 1.H-Black 2.DYB - Matte white 3.BZ - Perl white painted 4.HGTS - Red bronze 5.HTL = Yellow bronze brushed 6.Q = Bronze 7.QTSL = Bronze brushed bright 8.QTS = Bronze brushed matte 9.STS = Acid copper brushed 10.SDMGJ = Water plated rose gold 11.N = Nickel brushed bright light 12.NP = Nickel brushed 13.TJ = Titanium gold 14.TJLS = Titanium gold brushed 15.G = Gold 16.GJS = Gold brushed 17.GJSY = Zirconium gold wire drawing matte 18.PGJFY = Zirconium gold wire drawing matte bright light 19.PLSJ = Brushed gold 20.LSJY = Brushed gold matte 21.MGJ = Rose gold 22.MGJL = Rose gold brushed 23.DMGJ = Light rose gold brushed 24.HTS = Red bronze brushed 25.QHP = Grey 26.LSQH = Grey brushed 27.LHMGJ = Brushed yellow rose gold
Two hole, single outlet (fixed) combination tap assembly (chromium plated brass) incorporating quarter turn ceramic disc headworks with single lever operating members and a manual diverter to shower outlet. The spout outlet incorporates a plastic flow straightener. The product is supplied with a shower hose, handset and metal backnuts. Maximum working pressure 10 bar. Maximum operating temperature 65°C
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| F8121KP-** | Various | BSP 3/4" (M) | 10 bar | 85 °C | LANBIAO | Body | No | 1/4 Turn ceramic disk | Metal Backnuts | Flow Straightener | |
| F8141KP-** | Various | BSP 3/4" (M) | 10 bar | 85 °C | LANBIAO | Body | No | 1/4 Turn ceramic disk | Metal Backnuts | Flow Straightener |
1）No Suffix-Chrome 2) -**Represents the following different surface treatments: 1.H = Black 2.DYB = Matte white 3.BZ = Perl white painted 4.HGTS = Red bronze 5.HTL = Yellow bronze brushed 6.Q = Bronze 7.QTSL = Bronze brushed bright 8.QTS = Bronze brushed matte 9.STS = Acid copper brushed 10.SDMGJ = Water plated rose gold 11.N = Nickel brushed bright light 12.NP = Nickel brushed 13.TJ = Titanium gold 14.TJLS = Titanium gold brushed 15.G = Gold 16.GJS = Gold brushed 17.GJSY = Zirconium gold wire drawing matte 18.PGJFY = Zirconium gold wire drawing matte bright light 19.PLSJ = Brushed gold 20.LSJY = Brushed gold matte 21.MGJ = Rose gold 22.MGJL = Rose gold brushed 23.DMGJ = Light rose gold brushed 24.HTS = Red bronze brushed 25.QHP = Grey 26.LSQH = Grey brushed 27.LHMGJ = Brushed yellow rose gold
Page 110 of 131
We use cookies to give you the best possible experience with WRAS. Some are essential to provide website functions and ensure the website is secure. We also use cookies to help us understand how people use the site and to make improvements. Click "Accept All" to enable recommended settings or click "Manage cookies" to adjust your settings. For more details, see our Cookie Policy.
