Primaflow ranges of brass, DZR brass, chromium plated brass, nickel plated brass and DZR brass compression fittings for use with copper pipe to BS EN 1057. Maximum working pressure 16.0 bar. Maximum operating temperature 99°C.
Range of water meters with brass bodies, plastic turbines and EPDM washers. Inlets incorporate a plastic filter. Maximum working pressure 16.0 bar.
Non-metallic materials and components comply with BS6920 at 50°C
‘Wesan WP’ range of water meters with black epoxy coated cast iron bodies, plastic impellers and EPDM ‘O’-rings and lip seal (DN50-65 models) and EPDM ‘O’-rings and gasket + NBR ‘O’-ring (DN80-125 models). Maximum working pressure 16.0 bar. Cold water use only.
Range of water meters with brass bodies, plastic turbines and EPDM washers. Inlets incorporate a plastic filter. Maximum working pressure 16.0 bar.
Non-metallic materials and components comply with BS6920 at 50°C
Water meter manifold with a plastic body and EPDM O rings. The outlet incorporates a non-return valve, not suitable for backflow protection. Maximum working pressure 10.0 bar. Cold water use only.
Range of differential (DPI) or relative (RPI) pressure sensors (with or without temperature transmitter) with stainless steel bodies and EPDM ‘O’-rings. The DPI2 model consists of a sensor and fitting for a capillary tube which is used for measuring the differential pressure between either sides of the sensor. Maximum working pressure 30.0 Bar. Maximum operating temperature 100°C.
Concealed ceiling outlet with a brass body.
Non-metallic materials and components comply with BS6920 at 85°C
Range of tap outlets with plastic bodies incorporating a filter within the body with a hollow fibre filter membrane The filters are supplied with (and must be used with) a chrome plated brass adapter which incorporates a plastic flow regulator. Open outlet use only.
Non-metallic materials and components comply with BS6920 at 60°C
Range of mains booster pumps with brass bodies, plastic impellors, and EPDM ‘O’-rings. Maximum working pressure 10.0 bar. Cold water use only.
TP series 200 range of single stage pumps with electrocoated cast iron or bronze bodies, stainless steel impellers and EPDM ‘O’-rings. (TPE models are only available with electrocoated cast iron bodies). The products can incorporate the following shaft seal variations: BQQE (silicon carbide-silicon carbide) & BQBE (Silicon carbide-carbon). The TPE pumps are available with or without a sensor. Maximum working pressure 16.0 bar (TP and TPE40-XXX/2 and TP and TPE40 XXX/2 models). All other models 10.0 bar. Maximum operating temperature: Bronze models are 85°C, cast iron models are cold water use only.
CR(I)(N)(E) ranges of multistage centrifugal pumps incorporating stainless steel impellers, intermediate chamber and outer sleeve. CR(E) versions have cast iron bases and pump heads coated with black cathodic paint. CRI(E) and CRN(E) versions have stainless steel bases and pumpheads. The pumps are available with the following shaft seals HQQ*, HUU*, HUB*, HQB*, where * can be E for EPDM and V for FKM. Maximum working pressures: CR1, 3 or 5 (2-36 stages) Oval flange: 16.0 bar. CR1, 3 or 5 (2-36 stages) DIN/ANSI/JIS flange: 25.0 bar CRI/N1, 3 or 5 (2-36 stages) Flexi clamp with oval flange connection: 16.0 bar CR/I/N1, 3 or 5 (2-36 stages) DIN/ANSI/JIS flange, PJE, Flexi clamp or Triclamp: 25.0 bar CR10 (1-16 stages) Oval flange or DIN/ANSI/JIS flange: 16.0 bar. CR10 (17-22 stages) DIN/ANSI/JIS flange: 25.0 bar. CRI10 (1-16 stages) PJE, Flexi clamp, Flexi clamp with oval connection, Triclamp or DIN/ANSI/JIS flange: 16.0 bar. CRI10 (17-22 stages) PJE, Flexi clamp, Triclamp or DIN/ANSI/JIS flange: 25.0 bar CRN10 (1-22 stages) PJE, Flexi clamp, Flexi clamp with oval connection, Triclamp or DIN/ANSI/JIS flange: 25.0 bar. CR15 or 20 (1-7 stages) Oval flange: 10.0 bar. CR15 or 20 (1-10 stages) DIN/ANSI/JIS flange: 16.0 bar. CR15 or 20 (11-17 stages) DIN/ANSI/JIS flange: 25.0 bar. CRI15 or 20 (1-7 stages) Flexi clamp with oval flange connection: 10.0 bar CRI15 or 20 (1-10 stages) PJE, Flexi clamp, Triclamp or DIN/ANSI/JIS flange: 16.0 bar. CRI15 or 20 (11-17 stages) PJE, Flexi clamp, Triclamp or DIN/ANSI/JIS flange: 25.0 bar. CRN15 or 20 (1-17 stages) PJE, Flexi clamp, Flexi clamp with oval connection, Triclamp or DIN/ANSI/JIS flange: 25.0 bar. CR models: Cold water use only. CRI/CRN models: Cold water use only and from April 2023 99°C.
CR(N)(E) ranges of vertical multistage centrifugal pumps with stainless steel (CRN models) or black polymer coated cast iron bodies (CR models) and a stainless steel impeller. The products are available with or without a sensor. Maximum working pressure: 16.0 bar - CR(N)(E) 32 range with 1-7 stages, CR(N)(E) 45 range with 1-5 stages, CR(N)(E) 64 range with 1-5 stages. 30.0 bar - CR(N)(E) 32 range with 8-14 stages, CR(N)(E) 45 range with 6-11 stages, CR(N)(E) 64 range with 6-8 stages. 33.0 bar - CR(N)(E) 45 range with 12-13 stages. Maximum operating temperature - CR models are cold water use only. CRN models are cold water use only up to February 2nd 2023, and 99°C from February 3rd 2023.
‘UPM4’ range of circulator pumps with either a composite (plastic) or stainless-steel body, plastic impellor and EPDM ‘O’-rings. The 1”-1½” models are supplied with EPDM gaskets for the inlet and outlet. The 2” model has fibre/NBR gaskets. Maximum working pressure 10.0 bar. Maximum operating temperature 95°C ((CIL3) plastic body models), 99°C (S/Steel body models).
‘Homebooster’ pump with stainless steel body, plastic impeller and EPDM rubber ‘O’-rings. The product is supplied with two loose brass ¾” captive nut x ½” BSP (M) connectors and fibre gaskets for installation on the inlet and outlet. Maximum working pressure 10.0 bar. Maximum operating temperature 95°C.
Range of shower handsets with plastic bodies. The inlets incorporate a stainless-steel strainer and a built-in flow regulator. Open outlet use only.
Non-metallic materials and components comply with BS6920 at 60°C
Range of shower heads with plastic bodies (various finishes), incorporating plastic strainer or flow restrictor and EPDM o rings with stainless-steel strainers on the inlets. Open outlet use only.
Non-metallic materials and components comply with BS6920 at 60°C
Crometta 85 range of chrome plated plastic shower outlets, incorporating EPDM washers and flow regulator and stainless-steel strainer at the inlet.
Non-metallic materials and components comply with BS6920 at 60°C
Range of overhead shower outlets with plastic bodies (various finishes), EPDM O-rings and a stainless-steel strainer. Open outlet use only.
Non-metallic materials and components comply with BS6920 at 60°C
Range of overhead shower outlets (ABS bodies - various finishes, see model), incorporating NBR and EPDM ‘O’ rings that incorporate stainless-steel mesh strainers.
Non-metallic materials and components comply with BS6920 at 70°C
Range of shower outlets with brass bodies (various finishes). Open outlet use only.
Non-metallic materials and components comply with BS6920 at 60°C
Wall mounted shower outlets with white plastic body, and chrome plated metal connection fittings. Product incorporate a filter and a flow regulator. The product incorporates an approved check valve cartridge, however, the complete product has not been fully tested to demonstrate it provides backflow protection. Model: 02-000207 is only a replacement filter and is not supplied with the ½” (F) Adapter. Open outlet use only.
Non-metallic materials and components comply with BS6920 at 60°C
Range of shower kits consisting of shower handsets, shower hoses and riser rail assemblies.
Non-metallic materials and components comply with BS6920 at 60°C
Range of shower kits, (various finishes - see model), comprising of a shower hose (brass double interlocked, PEX lined) and a shower handset. Maximum operating temperature 60°C.
Range of showers handsets incorporating plastic bodies (chrome plated) Maximum operating temperature 60°C.
Range of wall mounted and ceiling mounted shower heads available in different finishes and flow rates. Open outlet use only.
Non-metallic materials and components comply with BS6920 at 65°C
Range of pillar taps (chromium plated brass), incorporating ceramic cartridge headworks with single lever operating member. Spout oultlet incorporates a plastic aerator. Maximum working pressure 10.0 bar.
Non-metallic materials and components comply with BS6920 at 60°C
Range of pillar taps (brass bodies, various finishes – see models) incorporating quarter turn ceramic disc headworks with either cross-top or single lever type operating members. The spout outlets incorporate plastic aerators. The products are supplied with metal backnuts. Maximum working pressure 10.0 bar.
Non-metallic materials and components comply with BS6920 at 60°C
Range of pillar taps, (brass bodies, various finishes – see models) incorporating quarter turn ceramic disc headworks with either cross-top or single lever type operating members. The spout outlets incorporate plastic flow straighteners. The product is supplied with metal backnuts. Maximum working pressure 10.0 bar.
Non-metallic materials and components comply with BS6920 at 60°C
Range of chromium plated stainless steel or brass interlocked shower hoses with an optional PVC outer layer. Incorporating either a PVC or TPE inner hose and EPDM gaskets. Maximum operating temperature 60°C.
‘TAQ’ range of stainless steel or grey nylon braided (indicated by ACB in model name), EPDM lined flexible hose assemblies, incorporating various end connections. Some of the possible end connections also incorporate EPDM washers, gaskets or ‘O’-rings. Maximum operating pressure 10.0 bar.
Non-metallic materials and components comply with BS6920 at 85°C
Range of multi-layer shower hoses with a PVC inner hose, supplied with EPDM ‘O’-rings.
Range of stainless steel indirect (single or twin coil), direct and heat pump unvented hot water storage cylinders. The heat pump models also incorporate a plate heat exchanger and a circulation pump. The secondary circuit is supplied with a temperature and pressure relief valve set at 7.0 bar@90.0˚C. The products are supplied with an inlet control group consisting of an adjustable pressure reducing valve, adjustable in the range of 0.8 bar - 6.0 bar, but factory pre-set at 3.0 bar, a strainer, am expansion relief valve set at 6.0 bar and an approved single check valve cartridge, verified by test (suitable for backflow protection against Fluid Category 2). The products are also supplied with an immersion heater, an expansion vessel (12, 19 or 24 litres depending on model) and a tundish. Maximum supply pressure to the inlet control group: 16.0 bar. Maximum working pressure: Secondary circuit: 5.5 Bar. Primary Circuit: 6.0 Bar (All models except for the Direct - DI prefix models). Maximum operating temperature 75°C.
Range of automatic air venting valves with brass bodies, stainless steel strainer, plastic float and EPDM ‘O’-rings and gaskets. Maximum working pressure 16.0 bar.
Non-metallic materials and components comply with BS6920 at 85°C
Range of wall mounted concealed blending valves with brass bodies. Incorporating a thermostatic mixing valve with a single lever operating member controlling the temperature to 2 separate outlets. The product incorporates approved single check valves on the inlets; however, the complete product has not been fully tested to demonstrate it provides backflow protection Maximum working pressure 5.0 Bar
Non-metallic materials and components comply with BS6920 at 60°C
Range of adjustable or pre-set T-type thermostatic blending valves with brushed chromium plated DZR brass bodies. Supplied with an olive and compression nut. Maximum working pressure 10.0 bar.
Non-metallic materials and components comply with BS6920 at 85°C
Range of thermostatic bar type shower valve (brass body various finishes), incorporating a thermostatic cartridge controlling the temperature with a manual overide and a half turn ceramic disc headwork controlling the flow to 1 outlet (models CEL-149/DSG-149) or a manual diverter with an off position to 2 outlets (all other models) with single lever or dome operating members. The inlets incorporate stainless steel strainers and approved check valve cartridges; however, the complete product has not been fully tested to demonstrate it provides backflow protection. The product is also supplied with a shower hose, handset and overhead shower. Maximum working pressure 5.0 bar.
Non-metallic materials and components comply with BS6920 at 65°C
Range of wall mounted, thermostatic shower valves with brass bodies (chrome plated finish), incorporating a ceramic disc headwork controlling the flow to an overhead or hand shower. The temperature is controlled independently via a thermostatic cartridge with a single lever operating member incorporating a manual override button. The product also incorporates stainless steel strainers and an approved check valve cartridge; however, the complete product has not been fully tested to demonstrate it provides backflow protection. Supplied with a shower handset and hose. Maximum working pressure 10.0 Bar.
Non-metallic materials and components comply with BS6920 at 60°C
Range of exposed thermostatic shower valves with brass bodies (various finishes) incorporating a half turn ceramic disc headwork controlling the flow between 2 outlets, with the temperature being controlled independently via a thermostatic cartridge both with a single lever operating member. The inlets incorporate stainless steel strainers and approved check valve cartridges; however, the complete product has not been fully tested to demonstrate it provides backflow protection. Maximum working pressure 10.0 bar.
Non-metallic materials and components comply with BS6920 at 60°C
Range of exposed thermostatic blending valves, (chrome plated brass) incorporate a single sequential headwork controlling both the flow and temperature with single lever operating member. Model INSVDEV002 & INSMEV003 incorporates a non-rising spindle headwork controlling the flow and a thermostatic cartridge independently controlling the temperature The inlets incorporate stainless steel strainers and incorporates an approved check valve cartridge however, the complete product has not been fully tested to demonstrate it provides backflow protection. Model INSMEV003 also incorporates flow regulators. The products are supplied with shower hose, handset, and riser rail assemblies. Model INSMBIV004 is also supplied with a wall outlet. Maximum working pressure 5.0Bar for model (INSVEV002) Maximum working pressure 10.0Bar for model (INSVDEV001, INSMEV003 & INSMBIV004)
Non-metallic materials and components comply with BS6920 at 65°C
Range wall mounted, concealed, thermostatic shower valves (chrome plated brass, trim sets) incorporating a quarter turn ceramic disc headwork that controls the flow using cube or dome type operating members. The temperature is controlled independently via a thermostatic cartridge also cube or dome type operating members. Both inlets incorporate an approved check valve cartridge, however, the complete product has not been fully tested to demonstrate it provides backflow protection. The products can be supplied with fixed arms and overhead showers. Maximum working pressure 5.0 Bar
Non-metallic materials and components comply with BS6920 at 70°C
Range of concealed, thermostatic shower valves incorporating half turn ceramic disc headworks controlling and diverting the flow and the temperature is controlled independently via a thermostatic cartridge, both using either round or square operating members. Both inlets incorporate approved check valve cartridges, however, the complete product has not been fully tested to demonstrate it provides backflow protection. The products can be supplied with wall outlets, fixed arms, shower handsets, shower hoses and overhead showers. Maximum working pressure 5.0 Bar
Non-metallic materials and components comply with BS6920 at 70°C
Range of concealed electronic thermostatic shower valve with a plastic body, the flow is controlled via two motorised valves for hot and cold supply. Both inlets incorporate a plastic strainer and an approved check valve cartridge; however, the complete product has not been fully tested to demonstrate it provides backflow protection. Model 704014 is the valve only; all other models are supplied with isolation valves and model HQD1003 is supplied with an exposed elbow. Maximum working pressure 7.0 Bar
Non-metallic materials and components comply with BS6920 at 65°C
Range of concealed electronic thermostatic shower valve with a plastic body, the flow is controlled via two motorised valves for hot and cold supply. Both inlets incorporate a plastic strainer and an approved check valve cartridge; however, the complete product has not been fully tested to demonstrate it provides backflow protection. The products are supplied with isolation valves and wall mounted concealed diverter valves with plastic bodies. Maximum working pressure 7.0 Bar
Non-metallic materials and components comply with BS6920 at 65°C
Range of electronically controlled thermostatic shower mixing valve with a plastic body. Temperature is controlled via two motorised valves and a thermistor. The product also incorporates a pump and plastic filters on each inlet. The products are supplied with wall outlets, fixed arms, fixed heads, isolation valves. Model ISD.A2.14 is also supplied with an exposed elbow. Maximum working pressure 7.0 Bar
Non-metallic materials and components comply with BS6920 at 65°C
A range either concealed or exposed wall mounted thermostatic mixing valves with brass bodies (exposed models are chromium plated). Models CONCEALED007 & CONCEALED008 incorporate ¼ turn ceramic disc headworks and a manual diverter with a shut off. All models incorporate a thermostatic cartridge that controls the temperature. The inlets of all models incorporate stainless steel filters and approved check valve cartridges; however, the complete product has not been fully tested to demonstrate it provides backflow protection. Maximum working pressure 10 bar. Maximum working temperature 60°C.
Range of wall mounted, bar type thermostatic blending valves (chromium plated brass) incorporating a 2-way manual diverter valve controlling and diverting the flow between an overhead shower and a shower outlet with dome type operating members. The temperature is controlled independently via a thermostatic cartridge with a dome type operating member incorporating a manual override button. Inlets incorporate approved check valve cartridges, however, the complete product has not been fully tested to demonstrate it provides backflow protection. Maximum working pressure 10.0 bar. Maximum operating temperature 65°C
Range of wall mounted, concealed thermostatic blending valves or exposed bar type thermostatic blending valves (chromium plated brass) incorporating a 2-way manual diverter valve controlling and diverting the flow between an overhead shower and a shower outlet with dome type operating members. The temperature is controlled independently via a thermostatic cartridge with a dome type operating member incorporating a manual override button incorporate. An approved check valve cartridge is also supplied, however, the complete product has not been fully tested to demonstrate it provides backflow protection. The products are supplied with a shower head, shower hose and handset. Maximum working pressure 10.0 bar. Maximum operating temperature 65°C (F4017x & F2167x models. All other models 60°C only).
Range of wall mounted thermostatic blending valves (chrome plated brass), incorporating a quarter turn ceramic disc, half turn ceramic disc or ceramic cartridge headworks (see models). The temperature is controlled independently via a thermostatic cartridge incorporating a manual override button, with a variety of operating members. The inlets incorporate approved check valve cartridges; however, the complete product has not been fully tested to demonstrate it provides backflow protection with stainless-steel strainers. Maximum working pressure 5.0 Bar.
Non-metallic materials and components comply with BS6920 at 60°C
Range of wall mounted thermostatic blending valves (chrome plated brass), incorporating a quarter turn ceramic disc, half turn ceramic disc or ceramic cartridge headworks (see models). The temperature is controlled independently via a thermostatic cartridge incorporating a manual override button, with a variety of operating members. The inlets incorporate approved check valve cartridges; however, the complete product has not been fully tested to demonstrate it provides backflow protection with stainless-steel strainers. Maximum working pressure 5.0 Bar.
Non-metallic materials and components comply with BS6920 at 60°C
Wall mounted, thermostatic shower valve (chromium plated brass body) incorporating a two-way diverter valve headwork that controls flow between each shower outlet with a cube type operating member. The temperature is controlled independently via a thermostatic cartridge with a cube type operating member with a manual override button. Both inlets incorporate a stainless-steel strainer and approved check valve cartridges, however, the complete product has not been fully tested to demonstrate it provides backflow protection. Maximum working pressure: 10.0 Bar. Maximum operating temperature: 85°C.
Page 68 of 236
We use cookies to give you the best possible experience with WRAS. Some are essential to provide website functions and ensure the website is secure. We also use cookies to help us understand how people use the site and to make improvements. Click "Accept All" to enable recommended settings or click "Manage cookies" to adjust your settings. For more details, see our Cookie Policy.
