'581189 Center Jet Blue Plus'. Off-white coloured, PTFE paste intended for use as a thread sealant. For use with water up to 23°C.
'Mega All White'. White coloured (opaque) anaerobic sealant/adhesive. Apply in strict accordance with manufacturer's instructions 'issue 01' dated '09/09/2021'. For use with water up to 85°C.
'D77 Nut Grade Adhesive & D377 Thread Sealant'. Site applied, green coloured anaerobic adhesives. Apply and cure as per manufacturer's instructions. D77 is for use with water up to 85°C. D377 is for use with water up to 23°C.
'Key Plumb'. Clear, transparent (un-pigmented) solvent cement, (intended to join PVC pipe and fittings). Apply as per manufacturer's instructions. Cure for 20 days at 7°C. For use with water up to 65°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Ixef DW 1022 BK001 & Ixef FC-1022 BK001'. Black coloured, injection moulded polyarylamide materials. For use with water up to 85°C.
'DESTONE DSC7500G6'. Black coloured, injection moulded polyketone material. For use with water up to 85°C.
'ULTEM', injection moulded polyetherimide materials. For use with water up to 85°C. PW1000-1000, PW1000-1000 and PW1000-1000W (yellow coloured). PW2100-1000, PW2100-1000 and PW2100-1000W (brown coloured). PW2200-1000 & PW2300-1000 (beige coloured). PW2400-1000 (grey coloured). PW1000-7101, PW2100-7301, PW2100-7301, PW2100-7301W, PW2200-7301, PW2300-7301 & PW2400-7301 (black coloured). ULTEM PW2300-1000 and ULTEM PW2300-1000W were added to the approval in June 2025.
'Hytrel® HTR6108'. Translucent cream coloured, injection moulded thermoplastic elastomeric material. Shore hardness 61. For use with water up to 85°C.
BS1212-4 (2016) compact type float operated valve for WC flushing cisterns, side entry type. The inlet incorporates a plastic flow restrictor. Maximum working pressure 10.0 bar. Cold water use only.
Range of WC flushing cisterns incorporating a BS 1212-4 (2016) side entry compact type float operated inlet valve providing a Type AG air gap with a dual flush drop valve for full flush volumes of up to 6 litres and a reduced flush of up to 4 litres or 4.5/3 litre flush volumes. The cistern is operated by a manual push button and the product incorporates a servicing valve on the inlet supply. Maximum working pressure 10.0 bar. Cold water use only.
WC flushing cistern incorporating a side entry compact type float operated inlet valve providing a Type AG air gap with a dual flush drop valve for full flush volumes of up to 6 litres and a reduced flush of up to 4 litres. The cistern is operated by a manual push button and incorporates a servicing valve on the inlet supply. Maximum working pressure 10.0 bar. Cold water use only.
Spring loaded resilient trim, in-line check valve cartridge with plastic guides and stem and EPDM seals within a plastic housing. For insertion into pipes or fittings with specifically dimensioned bores. Maximum working pressure 16.0 bar & maximum operating temperature 65°C.
Range of single check valve assemblies with DZR brass bodies. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Non-verifiable single check valve assembly consisting of a spring loaded, resilient trim, single check valve cartridge with a brushed chrome DZR brass body. Maximum working pressure 10.0 bar. Maximum operating temperature 85ºC.
Non- verifiable double check valve assembly consisting of two spring loaded resilient trim in-line check valve cartridges housed in a chrome plated DZR brass body with an integral insolation valve between the cartridges. For use with copper pipes to EN1057. Maximum working pressure 10.0 bar. Maximum operating temperature 85°C.
Ceramic cartridge headwork incorporating a plastic body and EPDM rubber seals, for insertion into specifically dimensioned tap assemblies. Maximum working pressure 5.0 bar. Maximum operating temperature 90°C.
Quarter turn ceramic disc headwork incorporating a plastic body to be housed in specifically dimensioned bodies. Maximum working pressure 10.0 bar. Maximum operating temperature 90°C.
A ceramic cartridge headwork with a plastic body and EPDM ‘O’-rings for insertion into specifically dimensioned assemblies. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.
Range of ceramic cartridge headworks incorporating NBR ‘O’ rings and silicone seals. For insertion into specifically dimensioned tap assemblies. Maximum working pressure 10.0 bar. Maximum operating temperature 85°C.
Range of ceramic disc headworks incorporating brass bodies and NBR ‘O’-rings. For insertion into any specifically dimensioned tap assemblies. Maximum working pressure 12.0 bar. Maximum operating temperature 85°C.
Page 65 of 177
We use cookies to give you the best possible experience with WRAS. Some are essential to provide website functions and ensure the website is secure. We also use cookies to help us understand how people use the site and to make improvements. Click "Accept All" to enable recommended settings or click "Manage cookies" to adjust your settings. For more details, see our Cookie Policy.
