Range of wall mounted, thermostatic blending shower valves, incorporating a quarter turn ceramic disc headworks or ceramic disc diverter cartridges (see models) with a cube type operating members. The temperature is controlled independently via a thermostatic cartridge with a cube type operating members that incorporate manual override buttons. Model (1.1901.001) is supplied with a shower hose, hanset & riser rail assemblies. Model (1.1901.002) is supplied with a shower hose, handset, overhead shower & riser rail assebmlies. The inlets incorporate stainless steel strainers and approved check valve cartridges, however, the complete product has not been fully tested to demonstrate it provides backflow protection. Maximum operating pressure 10 bar. Maximum operating temperature 45°C
Non-metallic materials and components comply with BS6920 at 45°C
Range of wall mounted thermostatic shower valves (various finishes) incorporating a quarter turn ceramic disc headworks with single lever type operating members. The temperature is controlled independently via a thermostatic cartridge with manual override and single lever type operating members. Both inlets incorporate approved single check valve cartridges (however, the complete assembly has not been fully tested to demonstrate that it provides adequate backflow protection). The products are supplied with shower kits consisting of a shower hose, handset & a riser rail assembly. Maximum working pressure 5.0 Bar Maximum operating temperature 85°C.
Range of wall mounted concealed thermostatic shower valves (brass bodies with chrome plated plastic trim sets), incorporating a quarter turn ceramic disc headwork controlling the flow. The temperature is controlled independently via a thermostatic cartridge, both using dome type operating members. The inlets incorporate stainless-steel strainer washers and single check valve cartridges (however, the complete product has not been fully tested to demonstrate it provides backflow protection). The products are supplied with a chrome plated shower handset, shower hose, plastic wall mounted shower outlet and riser rail assembly. Maximum working pressure 10.0 bar.
Non-metallic materials and components comply with BS6920 at 60°C
Range of wall mounted, concealed thermostatic blending valves or exposed bar type thermostatic blending valves (chromium plated brass) incorporating a 2-way manual diverter valve controlling and diverting the flow between an overhead shower and a shower outlet with dome type operating members. The temperature is controlled independently via a thermostatic cartridge with a dome type operating member incorporating a manual override button incorporate. An approved check valve cartridge is also supplied, however, the complete product has not been fully tested to demonstrate it provides backflow protection. The products are supplied with a shower head, shower hose and handset. Maximum working pressure 10.0 bar. Maximum operating temperature 65°C (NU‐035 & NU‐037 models. All other models 60°C only).
Wall mounted, shower control valve, (brass body – various finishes), incorporating a half turn ceramic disc headwork using a dome type operating member. The shower outlet connection incorporates an approved check valve cartridge (however, the complete assembly has not been fully tested to demonstrate that it provides adequate backflow protection). Maximum working pressure 10 bar. Maximum operating temperature 70°C
Range of non-return, swing gate valves with gunmetal bronze bodies. Maximum working pressure 20.0 bar.
Non-metallic materials and components comply with BS6920 at 85°C
Range of non-return, swing gate valves with gunmetal bronze bodies. Maximum working pressure 20.0 bar.
Non-metallic materials and components comply with BS6920 at 85°C
Range of non-return, swing gate valves with gunmetal bronze bodies. Maximum working pressure 20.0 bar.
Non-metallic materials and components comply with BS6920 at 85°C
Range of non-return, swing gate valves with gunmetal bronze bodies. Maximum working pressure 20.0 bar.
Non-metallic materials and components comply with BS6920 at 85°C
Range of non-return, swing gate valves with gunmetal bronze bodies. Maximum working pressure 20.0 bar.
Non-metallic materials and components comply with BS6920 at 85°C
Range of non-return, swing gate valves with gunmetal bronze bodies. Maximum working pressure 20.0 bar.
Non-metallic materials and components comply with BS6920 at 85°C
Range of non-return, swing gate valves with gunmetal bronze bodies. Maximum working pressure 20.0 bar.
Non-metallic materials and components comply with BS6920 at 85°C
Range of non-return, swing gate valves with gunmetal bronze bodies. Maximum working pressure 20.0 bar.
Non-metallic materials and components comply with BS6920 at 85°C
Range of pressure reducing valves with DZR brass bodies. Maximum inlet supply pressure 25.0 bar. Outlet supply pressure is adjustable within the range of 1.5 bar to 6.0 bar. Maximum operating temperature 70°C.
Inlet control group consisting of an in-line pressure reducing valve (adjustable pressure - see model) and a pre-set expansion relief valve (pre-set pressure - see model) housed in a DZR brass body with an EPDM rubber diaphragm. The product incorporates a check valve cartridge, verified by test (suitable for backflow protection against Fluid Category 2). Compression connection to be used with copper pipe EN1057 only. Maximum supply pressure 10.0 bar. Maximum operating temperature 40°C.
Range of pre-set pressure relief valves (spring loaded) with DZR brass body. Model SRV0353SW0475 is set at 4.75 bar, SRV0350SW060 is set at 6.0 bar and SRV03540505003 is set at 3.0 bar. Maximum operating temperature 85°C.
Range of normally closed solenoid valves with plastic bodies, EPDM ‘O’-rings and diaphragm. The inlet incorporates a combined plastic filter and stainless-steel strainer. Maximum working pressure 10.0 bar. Maximum operating temperature 85°C.
Range of solenoid valves with plastic bodies and silicone membrane. Maximum working pressure 8.0 Bar. Maximum operating temperature 65°C.
Non-metallic materials and components comply with BS6920 at 65°C
“Ballofix®Lock” range of in-line hex key operated spherical valves with PTFE seals and EPDM ‘O’-rings. 3399300 & 3499300 models have a brass body. 3599300, 37199300 & 38199300 models have a DZR brass body. All models have a DZR brass ball (chromium plated). Maximum working pressures: 3399300, 3499300 and 3599300 models are 16.0 bar. 37199300 and 38199300 models are 25.0 bar. Maximum operating temperature 95°C.
‘3029’ range of lever operated spherical valves with chromium plated brass bodies and balls, incorporating PTFE seats and EPDM ‘O’-rings. Maximum working pressure 25.0 bar. Maximum operating temperature 99°C.
Range of press fit spherical valves with DZR brass bodies and balls with EPDM O-Rings. Joints are achieved by the use of a press fitting tool. For use with Multi-layered Pert/Al/Pert pipe compliant to EN21003-2 Maximum working pressure 10.0 bar. Maximum operating temperature 95°C.
Range of spherical valves with brass bodies and stems, incorporating chrome plated brass ball and EPDM O-rings and single lever operating members. Maximum supply pressure 24.0 bar.
Non-metallic materials and components comply with BS6920 at 85°C
Range of gate valves with a non-rising spindle with a handwheel operating member. All models have brass body and brass wedge. For use with copper pipe (manufactured to EN1057). Maximum working pressure 16.0 bar.
Non-metallic materials and components comply with BS6920 at 85°C
Range of cast iron gate valves with blue epoxy coating, EPDM coated disc, PTFE gasket and EPDM seals. The valves are operated via a non-rising spindle headwork with a hand wheel operating member. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Range of resilient seated gate valves with cast iron bodies (blue epoxy coated), EPDM coated cast iron wedges and a handwheel operating member. Maximum working pressure 16.0 bar.
Non-metallic materials and components comply with BS6920 at 85°C
Range of gate valves with blue epoxy coated ductile iron bodies and EPDM encapsulated wedge. The gate is operated via a hand wheel operating member. Maximum working pressure 16.0 Bar
Non-metallic materials and components comply with BS6920 at 85°C
Range of resilient seated gate valves with cast iron bodies (blue epoxy coated), EPDM coated cast iron wedges and a handwheel operating member. Maximum working pressure 16.0 bar.
Non-metallic materials and components comply with BS6920 at 85°C
Range of brass and DZR brass stopcock incorporating EPDM and PTFE washers. Compression connections, to be used with copper pipe EN1057 only. Maximum working pressure 16.0 bar.
Non-metallic materials and components comply with BS6920 at 85°C
Range of unvented monobloc groups consisting of an in-line pressure reducing valve (PRV) (adjustable between 2.7 and 3.3 bar or 3.2 and 3.8 bar - see model) and a pre-set expansion relief valve (SRV) (pre-set at either 4.5, 4.75, 5.0, 6.0 or 8.0 bar - see model) housed in a DZR brass body with an EPDM rubber diaphragm. The product incorporates a check valve cartridge, verified by test (suitable for backflow protection against Fluid Category 2). The expansion relief valve is fitted with a rotary type easing gear and the products are for use with copper pipe (manufactured to EN1057). Maximum inlet supply pressure 10.0 bar. Maximum operating temperature 85°C.
Range of water conditioners with brass and stainless steel bodies, PTFE seals and sacrificial zinc anode. Maximum working pressure 16.0 bar. Maximum operating temperature 80°C.use only.
'PA-727 CM1404 White & PA-727 CM1405 Grey'. White or grey coloured, injection moulded ABS materials. PA-727 CM1404 White is for use with water up to 85°C. PA-727 CM1405 Grey is for use with water up to 23°C.
'ZX-9 Zhenxin Epoxy Powder Coating'. Factory applied, blue coloured epoxy coating. Apply as per manufacturer's 'Preparation and Curing Conditions' instructions reference 'ZX-9-1', dated '2024/02/26'. Cure for 30 minutes@180°C. For use with water up to 85°C. If the curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'SYM-218'. Factory applied, grey coloured, two-part epoxy coating. Mix parts A & B in a 4.3:1 ratio and apply as per manufacturer's TDS 'XYJSMS001' dated '2023-01-10'. Cure for 168 hours@23°C. For use with water up to 65°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
KARUMEL EX4413-F103. Factory applied, fusion bonded, epoxy powder coating available in blue or red. Apply and cure in accordance with 'Application Guide KARUMEL EX4413-F103', issue 'KCSA-230201', dated February 2023, (curing as per Section 3.6). For use with water up to 85°C.
'SGPAM-CN-WB01'. Factory applied, blue coloured water based coating. Apply as per manufacturer's TDS 'PAMPIPE-TDC-WA04', version '4', dated '16/11/2022'. Cure for 30 minutes@50°C. For use with water up to 23°C. If the curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'TYSN-01'. Factory applied, grey coloured cement. Mix sand, water & cement in a 1.5:1.0:1.0 weight ratio and apply as per manufacturer's instructions file number 'GB1752023', edition 'A0', dated '2023-06-11'. Cure for 24 hours at 25°C. For use with water up to 65°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'CORROPOXY-FGE400'. Factory applied, red coloured, two-component epoxy coating. Mix and apply as per manufacturer's Application Procedures 'CPE/ FGE-400/Procd. /02', 'issue no - 03', dated '12.05.2022'. Cure for 30 minutes@45°C. For use with water up to 45°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified then the material is not covered by the scope of the approval.
'AYYTCM-01'. Factory applied, grey coloured cement mortar. Mix cement:sand:water in a 1:3.0:0.4 weight ratio and apply as per MSDS '20170508A1'. Air cure for 4 hours@23°C and the steam cure for 6 hours@60°C. For use with water up to 65°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
Luberpox – 2K – DS-Lackfarbe IV80, Wilo Grün nach Muster/IW80 Hardener (green coloured) & Luberpox – 2K – DS-Lackfarbe IV80, RAL 9011 Graphitschwarz/IW80 Hardener (black coloured). Factory applied epoxy coatings. Mix in a 5:1 weight ratio and apply as per Berger-Lacke Technical Data Sheet (rev. 41-06.11.2023). Cure for 7 days at 22°C. For use with water up to 23°C. These materials are only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the materials are not covered by the scope of the approval.
'LZYX002'. Factory applied, grey coloured cement mortar. Mix cement:sand:water in a 1:3.0:0.4 weight ratio and apply as per Instruction Sheet '201 8 07 0', revision 'A2'. Air cure for 4 hours@23°C and the steam cure for 6 hours@60°C. For use with water up to 65°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Welmortar-BFS'. Factory applied, grey coloured cement mortar. Mix sand:cement:water in a 3:2:1 weight ratio and apply as per manufacturer's SOP document 'WDIPL/QA/WI/14B', revision '01', dated '08.02.2023'. Cure for 28 days@30°C. For use with water up to 65°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Welmortar-SRP'. Factory applied, grey coloured cement mortar. Mix sand:cement:water in a 3:2:1 weight ratio and apply as per manufacturer's SOP document 'WDIPL/QA/WI/14C', revision '1', dated '08.02.2023'. Cure for 28 days@30°C. For use with water up to 65°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
‘Pilotpack 3480, 5035, 3435, 4040, 7099, 3408, 3410 & 5020’ range of gland packings. 3480 & 3435 are dark grey coloured, graphitised PTFE based. 5035 is yellow & black coloured, graphitised PTFE/aramid based. 4040 is grey coloured, graphite based. 7099 is white coloured, acrylic/PTFE based. 3408 is white coloured, lubricated PTFE based. 3410 is white coloured, lubricated PTFE based. 5020 is light yellow coloured, lubricated aramid based. All grades are for use with water up to 85°C. For use only as gland packing material having been tested at a reduced surface area to volume ratio.
'FH42Z', grey coloured, compression moulded carbon graphite disc. ‘FH82Z’, grey coloured, compression moulded carbon graphite disc was added to the approval in February 2024. Both are for use with water up to 85°C.
‘LURANYL® KR 2402 TW 35061, LURANYL® KR 2403 G4 TW 26343 & LURANYL® KR 2403 G6 TW 26343’. polyphenyleneoxide/polystyrene. In May 2025, ‘LURANYL® KR 2403 G2 TW GY4090-24’ & ‘LURANYL® KR 2403 G6 TW GY4040-24’, dark grey coloured, injection moulded polyphenyleneoxide/polystyrene materials were added to the approval. In November 2025, ‘LURANYL® KR 2403 G2 TW 26343’, black coloured, injection moulded polyphenyleneoxide/polystyrene material was added to the approval. All grades are for use with water up to 85°C.
'AH40-7484Z'. White coloured, injection moulded PPE material. For use with water up to 65°C.
'G40 SA'. Natural (appears cream), injection moulded PPS material. For use with water up to 65°C.
'Powertherm PP-R pipe'. Green coloured, extruded PP-R pipe (manufactured from SABIC Vestolen P 9421). For use with water up to 85°C.
'POWERtherm PP-R Fittings'. Green coloured, injection moulded PP-R fittings (manufactured from SABIC Vestolen P 9421). For use with water up to 85°C.
'STAR PIPE VULGARI.EPE PVC PRESSURE PIPE EN1452'. Black coloured, extruded PVC pipe. For use with water up to 23°C.
Page 56 of 131
We use cookies to give you the best possible experience with WRAS. Some are essential to provide website functions and ensure the website is secure. We also use cookies to help us understand how people use the site and to make improvements. Click "Accept All" to enable recommended settings or click "Manage cookies" to adjust your settings. For more details, see our Cookie Policy.
