Range of single hole, single outlet, manually operated flow control valve (brass bodies) incorporating a quarter turn ceramic disc headwork housed and supplied with either single lever, dome type or cross top (see model) operating members. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C
Range of in-line adjustable pressure reducing valves with Nickel plated DZR brass bodies and EPDM gaskets. Maximum inlet supply pressure 16.0 bar. Outlet pressure in the range of 0.5 bar to 6.0 bar. Maximum operating temperature 80°C.
Pre-set pressure relief valve (set @ 3.0 bar) incorporating a brass body, NBR ‘O’-ring and an EPDM diaphragm. The valve is fitted with a hand operated rotating easing gear. Maximum operating temperature 90°C.
Range of latching solenoid valves with brass bodies, incorporating stainless steel strainer with EPDM O rings and diaphragms Maximum working pressure 12.0 Bar or 16.0 Bar on (SCPH262C020 & SCPXH262C020BW TPL 21896 Only). Maximum operating temperature 85.0°C
Range of spherical ball valves with single lever or T-handle operating members, brass bodies (nickel plated) and chromium plated brass ball and PTFE washers. Maximum working pressure IN90 models = 40.0 bar. IN89 models = 25.0 bar. Maximum operating temperature 85.0°C
Range of electrically actuated ball valves incorporatingstainless steel bodies and ball with PTFE seat. Various closure options are available depending on model. Maximum working pressure 10.0 bar. Maximum operating temperature 100°C.
Range of spherical valves with lever operating member, stainless steel bodies, chromium plated stainless steel ball and PTFE seat. Maximum working pressure 66.0 bar. Maximum operating temperature 100°C.
Range of spherical valves incorporating brushed chome plated brass bodies, ball and PTFE seats. Maximum working pressure 10.0 bar. Maximum operating temperature 95°C
Flomasta Range of brass bodied or chrome plated brass bodied spherical valves, with a brass ball and EPDM ‘O’-rings. All fittings are to be used with PE-x pipe (manufactured to BS7291-3), PB pipe (manufactured to BS7291-2) and copper pipe. Maximum working pressure 10.0 bar. Maximum operating temperature 65°C.
Range of lever operated spherical valves incorporating brass bodies and brass ball (various finishes) to be used with PEX pipe (manufactured to BS7291 part 3), Polybutylene Pipe (manufactured to BS7291 Part 2) and copper pipe (manufactured to EN1057). Maximum working pressure 6.0 bar (for PEX and Polybutylene pipe). Maximum working pressure of 20.0 bar (for copper pipe). Maximum operating temperature 95˚C.
Range of motorised spherical valves with stainless steel bodies, ball and PTFE seals Maximum working pressure 16.0 bar. Maximum operating temperature 99˚C.
Range of spherical ball valves with lever or tee operating member, brass bodies, chromium plated brass ball and PTFE seat. Maximum working pressure 50.0 bar: ¼” (DN 8), 3/8” (DN 10) & ½” (DN 15). Maximum working pressure 40.0 bar: ¾” (DN 20) & 1” (DN 25). Maximum working pressure 30.0 bar: 1¼” (DN 32) & 1½” (DN 40). Maximum working pressure 25.0 bar: 2” (DN 50). Maximum operating temperature 60°C.
Range of spherical valves with bronze bodies (brushed chrome plated), brass ball and PTFE seals. Maximum working pressure 25.0 bar. Maximum operating temperature 85°C.
Flomasta Range of plastic bodied inline, tee and angled spherical valves with EPDM ‘O’-rings and either lever or screwdriver operated (see model). For use with copper and PE-x pipe (manufactured to BS7291-3). Maximum working pressure 10.0 bar. Maximum operating temperature 65°C.
Range of gate valves (gunmetal) with gunmetal bronze wedges, brass spindle and PTFE seals. Maximum working pressure 20.0 bar. Maximum operating temperature 100°C.
Range of gate valves incorporating bronze bodies and wedges with PTFE seals. The valves are operated via a non-rising spindle with a hand wheel operating member. Maximum working pressure 20.0 bar. Maximum operating temperature 85°C.
Flomasta Range of inline screw down stop valves with plastic bodies, non-rising spindle headworks and dome type operating members for use with PE-x (manufactured to BS7291-3) and copper pipe. Maximum working pressure/temperature: 10.0 bar @ 20°C and 10.0 bar @ 65°C.
Range of double regulating valves with bronze bodies, PTFE disc face and orifice plate, and EPDM rubber ‘O’-rings with thermostatic control elements and a manually adjustable flow control valve. Maximum working pressure 25.0 bar. Maximum operating temperature 85°C.
Range of front-loading commercial washing machines with flow controlled by solenoid valve and discharged via a type `AB` airgap (verified by test - suitable for backflow protection against fluid category 5). The machines are supplied with double check valve assemblies (suitable for backflow protection against Fluid Category 3) Maximum working pressure 10.0 bar. Maximum operating temperature 60°C
Range of ultra-violet disinfection units consisting of a stainless-steel body and quartz tubes with EPDM O rings. Maximum working pressure 16.0 bar. Maximum operating temperature 50.0°C
'Iupital F10-02 nat, Iupital F20-03 nat & Iupital FG2025 nat (white coloured). Iupital F10-02 E9000 black & Iupital F20-03 E9001 black (black coloured)'. Injection moulded acetal materials, (manufactured in Bangkok, Thailand). For use with water up to 85°C.
'A8401700'. White coloured, compression moulded Ceramic Alumina Al960 sealing ring. For use with water up to 85°C.
'MS1545A Enamel Coating'. Factory applied, blue coloured enamel coating. Apply as per document reference 'WRAS-sample-0001' dated 29.10.2020. Cure for 19 minutes (14 minutes in burner zone) @860°C. For use with water up to 85°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Interline 925P Off White'. Site applied, two-component, white coloured (once mixed) epoxy coating comprising of Part A (white coloured, opaque paint) and Part B (brown coloured, translucent liquid). Mix Parts A and B in a 4.93:1 mass ratio. Cure for 7 days@30°C. For use with water up to 60°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Jotapipe IL6001 50S'. Factory applied, blue coloured, fusion bonded epoxy coating. Apply as per technical data sheet dated '10 September 2019'. Cure for 15 minutes@230°C. For use with water up to 85°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Eurokote® 46-60 Red Brown'. Factory applied, red-brown coloured epoxy coating. Apply as per manufacturer's technical data sheet dated 19/11/2019. Cure for 7 days@20°C. For use with water up to 60°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Interline 925P Light Grey'. Site applied applied, two-component, grey coloured (once mixed) epoxy coating comprising of Part A (grey coloured, opaque paint) and Part B (brown coloured, translucent liquid). Mix Parts A and B in a 4.93:1 mass ratio. Cure for 7 days@30°C. For use with water up to 60°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Interline 925 White with Ceilcote 680M Primer'. Site applied, white coloured (once mixed), two-component epoxy coating comprising of a two-component primer and two-component top-coat. The primer (Ceilcote 680M) comprises of Part A (uncoloured liquid) and Part B (uncoloured liquid). Mix Parts A and B in a 3:1 volume ratio. Cure for 10 days@30°C. The top-coat (Interline 925 White) comprises of Part A (white coloured, opaque paint) and Part B (white coloured, opaque paste). Mix Parts A and B in a 4.99:1 mass ratio. Cure for 7 days@30°C. For use with water up to 23°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'MES Precast Tank Concrete Mix'. Factory made, grey coloured concrete & additive. Mix ingredients in the following percentages: Cement 19.10 %, Water 7.56 %, Coarse Aggregate 38.76 %, Fine Aggregate 34.46 %, Plastiment 186 0.03 % & ViscoCrete 0.12 %. Cure for 7 days@10°C. For use with water up to 23°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
`Novus N49 Graftec`. NBR/fibre material which is dark grey on one side and black on the other. For use with water up to 23°C. For use only as a jointing/gasket material having been tested at a reduced surface area to volume ratio.
‘Crystic 3846 BE (transparent, brown coloured) & Crystic 491 EPA (ME)’ Transparent, brown coloured and translucent, pale yellow coloured, contact moulded GRP materials. For use with water up to 23°C.
‘TECHNYL ® SAFE D 219WFC V30 BK’ & ‘TECHNYL ® SAFE D 219WFC V50 BK’. Black coloured, injection moulded, glass fibre reinforced polyamide 6.10 materials. For use with water up to 85°C.
'Grilon BG-35/2 natural & Grilon BG-35/2 black 9697'. Natural (appears white coloured, opaque) and black coloured, injection moulded PA6-GF35 materials. For use with water up to 85°C.
'Badadur PBT9 GF30 graphit 371 (grey coloured) & Badadur PBT9 GF30 Alpinweiss 230c (white coloured). Injection moulded Polybutylene terephthalate (30% glass fibres) materials. For use with water up to 65°C.
'Revolve 4068/N-250 (white coloured), M-586 (black coloured), M-638 (black coloured), M-694 (black coloured) & M-695 (black coloured)'. Polyethylene materials manufactured using rotational moulding. For use with water up to 85°C.
'Radel R-5100 GY 1037 (grey coloured), R-5100 GY1037 ECHO RP (grey coloured), R-5100 BK 937 (black coloured), R-5100 BK937 ECHO RP (black coloured) & R-5500NT (translucent)' - (manufactured in Oudenaarde, Belgium, Marietta, Ohio & RTP Company, USA). ‘R-5100 BU 1197 (blue coloured), R-5100 NT 15, R-5000 NT, R-5000 NT ECHO RP (natural), R-5100 NT ECHO RP (natural) & R-5100 NT (NT grades are natural and appear cream coloured, opaque)’ -(manufactured in Marietta, Ohio). ‘R-5100 GY1037LF’ (grey coloured - manufactured in Oudenaarde, Belgium and Marietta, Ohio). In July 2024, ‘Radel R-5100 GY1037 LF ECHO RP’ (grey coloured - manufactured in Oudenaarde, Belgium and Marietta, Ohio) was added to the approval. In November 2024, Radel R-5100 NT15 ECHO RP (NT grades are natural and appear cream coloured, opaque) & Radel R-5100 BU 1197 ECHO RP (blue coloured) were added to the approval. Injection moulded, polyphenylsulfone materials. For use with water up to 85°C.
‘Udel P-3500 NT LCD, GF-110 NT, GF-120 NT, GF-121 NT, P-1700 NT 11 MR & P-1700 NT 11’ (all beige translucent). ‘Udel P-1700 Grey 8057’ (grey coloured). ‘Udel P-1700 BK 937, P-1700 BK 937 MR, GF-120 BK 937 & GF-121 BK 937’ (all black coloured). ‘P-1700 WH 7407’ (white coloured). ‘Udel GF-121 BK 937 ECHO RP’ (black), ‘Udel GF-121 NT ECHO RP’ (beige translucent) & ‘Udel P-3500 NT LCD ECHO RP’ (beige translucent) were added to the approval in November 2024. ‘Udel GF-120 K 937 ECHO RP’ (black coloured) was added to the approval in April 2025. Injection moulded, polysulphone materials. For use with water up to 85°C.
'09-557'. Black coloured, compression moulded EPDM 'strip'. Shore hardness 80. Tested in-radius size 2.0mm. For use with water up to 85°C.
‘EP4118F, EP4518F, EP5118F, EP5518F, EP6118F, EP6518F, EP6512F (also known as EP6512P), E7008F, EP7118F, EP7518F, EP8018F, EP8118F, EP8518F & EP9118F’. Range of black coloured, compression moulded, EPDM ‘O’ rings and gaskets. Shore hardness between 40 & 90. ‘O’ rings with tested in-radii sizes of between 0.25mm & 5.00mm. Gaskets with tested in-radii sizes of between 0.25mm & 7.50mm. For use with water up to 85°C.
'EP5700'. Black coloured, compression moulded EPDM material. Shore hardness 57. Tested in-radius size 0.98mm. For use with water up to 23°C.
'Weld-On 919XG'. Uncoloured, transparent PVC solvent cement. Apply as per manufacturer's product data sheet '919XG-11-2020'. Cure for 30 minutes@4°C. For use with water up to 23°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Hytrel® 6359FG & 4068FG'. Cream coloured, injection moulded, thermoplastic polyester elastomeric materials. For use with water up to 85°C.
Single hole, single outlet (fixed) electronically controlled tap assemblies (chromium plated brass), flow is controlled by a solenoid valve activated via an infra-red sensor. The tap connects to the solenoid valve via a copper tail with a ½” BSP (F) captive nut and a fibre washer. The product is supplied with a combined TPE washer and stainless steel strainer to be installed on the inlet to the solenoid. The spout outlets incorporate a plastic flow straightener. Maximum working pressure 8.0 bar. Maximum operating temperature 60°C.
Range of single hole, single outlet (fixed) electronically operated, tap assemblies (chromium plated brass). Flow is controlled via solenoid valve and actuated by a touch sensor. The spout outlets incorporate a plastic aerator, supplied with stainless steel strainers. Maximum working pressure 8.0 bar. Maximum operating temperature 60°C.
Side entry BS1212-4 (2016) compact type float operated valve for WC flushing cisterns. The inlet incorporates a strainer. Maximum working pressure 10.0 bar. Cold water use only.
Side entry BS1212-4 (2016) compact type float operated valve for WC flushing cisterns. The inlet incorporates a plastic filter. Maximum working pressure 10.0 bar. Cold water use only.
Concealed WC dual flushing cistern with a vertical BS 1212-4(2016) float operated inlet valve providing a Type AG air gap arrangement and a dual flush pneumatic outlet valve. The flush volume is operated by a two push button assembly for a 6 or 3 litre flush volume. Maximum working pressure 10.0 bar. Cold water use only.
Spring loaded, resilient trim, in-line check valve cartridges with plastic body. For insertion into pipes and fittings with specifically dimensioned bores. Maximum working pressure 10.0 bar. Maximum operating temperature 85°C.
OV & OF ranges of spring loaded, resilient trim, in-line check valve cartridges within a plastic housing. For insertion in pipes and fittings with specifically sized bores. Maximum working pressure 16.0 bar. Models OF10/DN8 - 31.4208.0 & OF10/DN8-EPDM - 31.0059 have a maximum operating temperature of 60°C. Model OV10/DN8 – 31.4210.0 has a maximum operating temperature of 85°C.
Range of open or closed top, circular, sectional, cold water storage cisterns with corrugated & galvanised steel bodies and an EPDM liner.
Page 6 of 82
We use cookies to give you the best possible experience with WRAS. Some are essential to provide website functions and ensure the website is secure. We also use cookies to help us understand how people use the site and to make improvements. Click "Accept All" to enable recommended settings or click "Manage cookies" to adjust your settings. For more details, see our Cookie Policy.
