'AD-94 Sealing Ring'. White coloured, compression moulded ceramic sealing ring. For use with water up to 85°C.
'Eurokote® 47-20 Brun Rouge'. Factory applied, red coloured (once mixed and applied), two-component epoxy coating. Mix resin and hardener in an 80:20 mass ratio and apply as per manufacturer's instructions dated '15/06/2021'. Cure for 7 days@20°C. For use with water up to 60°C. his material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'E0-850-5210-001'. Factory applied, blue coloured epoxy powder coating. Apply as per manufacturer's instructions 'nr.01, rev.00, issue 01' dated 01/082016. Cure for 30 minutes@210°C. For use with water up to 85°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'POWTON E5000P-WT'. Factory applied, blue coloured epoxy powder coating. Apply as per manufacturer's TDS 'issue reference SPI 20170215' dated 21st January 2015. Cure for 15 minutes@230°C. For use with water up to 85°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'POWTON E5000P-WT (grey)'. Factory applied, grey coloured, epoxy powder coating. Apply as per manufacturer's TDS dated January 21st 2015. Cure for 15 minutes@230°C. For use with water up to 85°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Jotaguard VA 5001'. Blue coloured, factory applied, Fusion Bonded Epoxy Powder Coating. Apply as per manufacturer's application guide dated 'October 2018'. Cure for 5 minutes@245°C. For use with water up to 85°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'KARUMEL EX4412 (RAL5005) & KARUMEL EX4412 (Blue)'. Factory applied, blue coloured epoxy powder coatings. Apply as per manufacturer's application guide for potable water reference number 'KCSA-21090101' dated September 2021. For use with water up to 85°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Vandex Super'. Site applied, two-component, grey coloured (once mixed) cementitious coating. Mix cement powder with water in a weight ratio of 5:2. Apply as per manufacturer's Instructions for Use '2nd issue', dated '18.11.2020'. Cure for 21 days@7°C. For use with water up to 23°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the materials are not covered by the scope of the approval.
‘Sikalastic P 770’ (formerly known as ‘MasterSeal P 770’) Primer for use with ‘Sikalastic M 808’ (formerly known as ‘MasterSeal M 808 Grey’, and ‘MasterSeal M 808 Light Grey’) topcoats. Site applied coating system, which is light grey coloured (once mixed and applied), comprising of a primer and polyurethane coatings. Coat 1 primer: Mix parts A & B of ‘Sikalastic P 770’ Primer in a weight ratio of 2.2:2.8. Apply as per manufacturer’s IFU ‘version No. 1’, dated ‘22nd November 2024’. Cure for 24 hours@7°C. Coat 2 (coating): Mix parts A & B of ‘Sikalastic M 808’, dark grey coloured (once mixed) polyurethane coating in a weight ratio of 3.3:1.7. Apply as per manufacturer’s IFU ‘version No. 1’, dated ‘22nd November 2024’. Cure for 6 hours@7°C. Coat 3 (water contact coating): Mix parts A & B of ‘Sikalastic M 808’, light grey coloured (once mixed) polyurethane coating in a weight ratio of 3.3:1.7. Apply as per manufacturer’s IFU ‘version No. 1’, dated ‘22nd November 2024’. Cure for 7 days@7°C. When applying the coating system to GRP there is no need to apply a primer. Mix, apply and cure ‘Sikalastic M 808’ dark grey and then mix, apply and cure ‘Sikalastic M 808’ light Grey (water contact layer) as detailed above. For use with water up to 23°C.
‘Intergard 269 & Interline 975’. Site applied, white coloured Epoxy coating system comprising of a base coat and a topcoat. ‘Intergard 269’ is a two-component base coat which comprises of Part A (red/brown coloured) and Part B (straw coloured). Mix Part A & Part B in a mass ratio of 7.46:1 and apply as per manufacturer’s TDS ref. ‘206’, dated 08/02/2021. Cure for 12 days@25°C. ‘Interline 975’ is a two-component topcoat which comprises of Part A (white coloured) and Part B (straw coloured). Mix Part A & Part B in a mass ratio of 3.12:1 and apply as per manufacturer’s TDS ref. ‘3577’, dated 31/07/2017. Cure for 14 days@25°C. For use with water up to 23°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'CanSEALER (CS1)-TS'. Site applied, colourless waterproofing sealer which can be applied to cement with a roller or a brush. Apply one coat with a roller or a brush as per manufacturer's Technical Data Sheet 'CS1-210002'. Cure for 36 days@5°C. When applied by brush the material is for use with water up to 23°C. When applied by roller the material is for use with water up to 85°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'TPU inner hose (YOUSHI/3017)'. Transparent, colourless, extruded TPU hose. For use with water up to 85°C.
'K422'. Clear, silicone lubricant aerosol. Apply as per manufacturer's instructions 'version 1.0' dated 'May 2022'. For use with water up to 85°C.
'Ultramid A3EG7 FC Aqua Black 23285'. Black coloured, injection moulded PA66 material. For use with water up to 65°C.
'Zytel® HTNFG52G35HSLR BK011'. Black coloured, injection moulded polyphthalamide (PPA) material. For use with water up to 85°C.
'Ultramid D3EG10 FC Aqua Black 23285'. Black coloured, injection moulded polyamide material. For use with water up to 65°C.
'Badadur PBT9 GF30 Natur S1' (appears cream in colour) and 'Badadur PBT9 GF30 grau 930a' (grey coloured). Natural or grey coloured, injection moulded, glass reinforced PBT materials. For use with water up to 85°C.
'Radius Systems Puriton Light Blue Barrier Pipe [Type A, BS8588]' (formerly known as 'Radius Systems Puriton II LB Pipe' until March 2025). Extruded, triple layered pipe consisting of a black coloured polyethylene inner layer, aluminium middle layer and blue coloured polyethylene outer layer. For use with water up to 23°C.
‘Xytron™ G4020DW-FC BK00001 & Xytron™ G3020DW-FC BK00001’. Black coloured, injection moulded PPS materials. In September 2023 ‘Xytron G4020DW-FC NA99001’, natural (appears beige), injection moulded PPS material was added to the approval. All are for use with water up to 85°C.
'TORELINA A673MB2'. Grey coloured, injection moulded PPS material. For use with water up to 85°C.
'RH-PPR-32 Fitting'. Green coloured, injection moulded PPR fittings. For use with water up to 85°C.
'RH-PPR-32 Pipe'. Green coloured, extruded PPR pipe. For use with water up to 85°C.
'4270' components. Black coloured, injection moulded EPDM rubber components with a shore hardness of 70. ‘O’ rings (in-radius 1.31mm), washers (in-radius 1.05mm) & membranes (in-radius 1.75mm) made in Italy. ‘O’ rings (in-radius 1.31mm) & washers (in-radius 1.05mm) made in China. In May 2024 ‘shaped seals’ (in-radius of 1.8mm) made in Italy, were added to the approval. In November 2024, lip seals (in-radius of 0.7mm) made in Italy, were added to the approval. For use with water up to 85°C.
'VL1713M266B Black'. Black coloured, compression moulded EPDM rubber material. Shore hardness 60. Tested in-radius size 1.02mm. For use with water up to 85°C.
‘AA9HWZ (88 Sh.)’. Grades ‘AA6HWZ (60 Sh.), AA7HWZ (70 Sh.), AA7SWZ (70 Sh.), AA8HWZ (80 Sh.) were added in December 2022. Black coloured, compression moulded EPDM sheet materials. With a shore hardness of between 60 & 88. Tested in-radius size 1.15mm. For use with water up to 85°C.
'Silopren LSR 2630, 2640, 2650, 2660 & 2670'. Natural (appears clear), compression moulded silicone rubber sheet materials. Shore hardness between 30 & 70. Tested in-radius size of 1.0mm. For use with water up to 85°C.
'Innotec Thread Seal'. Anaerobic adhesive which is available in a yellow colour or in a yellow/orange colour. Apply as per manufacturer's instructions and cure for 15 minutes@25°C or 24 hours@22°C. For use with water up to 85°C. This product is to be applied and cured in strict accordance with the manufacturer's instructions.
Range of floor standing, single hole, single outlet (fixed) combination tap assemblies with brass bodies (various finishes), incorporating a ceramic cartridge headwork with a single lever operating member and a lockable diverter to shower outlet. The spout outlet incorporates a plastic aerator. The product is supplied with a shower hose and handset. Maximum working pressure 5.0 bar. Maximum operating temperature 75°C.
Range of deck mounted, single hole, single outlet (fixed) electronically operated tap assemblies (Chromium plated brass). Flow is controlled by a solenoid valve activated via an infra-red sensor. The products are supplied with a tee piece for installation prior to the solenoid valve. The inlets of the tee piece incorporate a combined NBR gasket and stainless steel filter and an approved check valve cartridge, however, the complete product has not been fully tested to demonstrate it provides backflow protection. The products are also supplied with stainless steel braided PEX lined flexible (connecting) hose assemblies and angled spherical valves incorporating a stainless steel strainer for installation on each inlet. Temperature is controlled by adjusting the opening of each angled spherical valve. The spout outlet incorporates a plastic aerator. Maximum working pressure 5.0 bar. Maximum operating temperature 60°C
Concealed WC dual flushing cistern with a BS 1212-4 (2016) float operated inlet valve providing a Type AG air gap arrangement and a dual flush pneumatic outlet valve. The flush volume is operated by a two-push button assembly for a 6 or 3 litre flush volume. Maximum working pressure 10.0 bar. Cold water use only.
Range of in-line non-verifiable single check valve assemblies consisting of a spring loaded resilient trim single check valve cartridge housed within a DZR brass brass body. Maximum working pressure 10.0 bar. Maximum operating temperature 85°C.
Range of in-line non-verifiable single check valve assemblies consisting of a spring loaded resilient trim single check valve cartridge housed within a nickel plated DZR brass body. For use with copper pipe (manufactured to EN1057). Maximum working pressure 10.0 bar. Maximum operating temperature 85°C.
Range of in-line, non-verifiable single check valve assemblies with DZR brass bodies and spring loaded, resilient trim check valve cartridges. Maximum working pressure 10.0 bar. Maximum operating temperature 85ºC
Range of one-piece and two-piece pre-insulated GRP cold water storage cisterns. Cisterns are supplied with a float operated inlet valve, screened overflow and screened vent. Cold water use only.
Range of quarter turn ceramic disc headworks with brass bodies, intended for insertion into specifically dimensioned tap assemblies. Maximum working pressure 5.0 bar. Maximum operating temperature 85°C.
Range of ceramic disc diverter headworks with or without a on/off function, to be installed in specifically dimensioned bores. Maximum working pressure 12.0 bar. Maximum operating temperature 85°C.
Manual diverter headwork incorporating a plastic body and silicone seals for insertion into specifically dimensioned bores. Maximum working pressure 10 bar. Maximum operating temperature 85°C.
Range of thermostatic cartridges with brass bodies and EDPM ‘O’-rings. All models expect XB-12T incorporate stainless steel strainers. For insertion into specifically dimensioned bores. Maximum working pressure 10.0 bar. Maximum operating temperature 85°C.
Range of thermostatic cartridges with plastic bodies and EPDM ‘O’-rings. All models incorporate a plastic strainer. For insertion into specifically dimensioned bores. Maximum working pressure 16 bar. Maximum operating temperature 60°C.
Single hole, single outlet fixed combination tap assemblies (chrome plated brass), incorporating quarter turn ceramic disc headworks with a cross-top operating members. The spout outlet incorporates a plastic flow straightener. Maximum operating pressure 10.0 bar. Maximum operating temperature 65°C
Range of single hole, single outlet (fixed) combination tap assemblies (chromium plated brass), incorporating a ceramic cartridge headwork with a single lever operating member. The spout outlet incorporates a plastic aerator. The 32.825.00E and 32.883.000 models are supplied with a pop-up waste. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.
Range of single hole, single outlet (swivel) combination tap assemblies (chromium plated brass) Models F1025S, F5126 and F5122L incorporate a ceramic cartridge headwork with a single lever operating member All other models incorporate ceramic disc headwork with single lever operating members. The spout outlets incorporate plastic aerator. Maximum working pressure 10.0 bar. Maximum operating temperature 65°C.
Range of single hole, single outlet (swivel) combination tap assemblies (brass body, various finishes - see model), incorporating quarter turn ceramic disc headworks with single lever, cross top or wheel operating members. The spout outlet incorporates a plastic aerator and the products are supplied with a click type pop-up waste. Maximum operating pressure 5.0 bar. Maximum operating temperature 65°C.
Range of single hole, single outlet (swivel) combination tap assemblies with brass bodies (various finishes), incorporating a ceramic cartridge headwork with a single lever operating member. The cold water inlet incorporate an approved check valve cartridge, verified by test (as suitable for backflow protection against Fluid Category 2) The spout outlets incorporate a plastic aerator. Maximum working pressure 5.0 bar. Maximum operating temperature 60°C.
Range of single hole, single outlet (swivel) combination tap assemblies with brass bodies (various finishes). Incorporating a quarter turn ceramic disc headworks with either single lever, dome or cross-top operating members. The spout outlets incorporate plastic aerators or flow straighteners with a stainless steel strainer. Maximum working pressure 10.0 bar. Maximum operating temperature 65°C
Range of single hole, single outlet (swivel) combination tap assemblies (various finishes) incorporating quarter turn ceramic disk headworks with single lever operating members. The cold water inlets is supplied with a chrome plated brass adapter incorporating an approved check valve cartridge which has been verified by test (as suitable for backflow protection against Fluid Category 2) The spout outlets incorporate plastic aerators. Maximum working pressure 5 bar. Maximum operating temperature 60°C.
Range of two-hole, deck mounted single outlet (fixed) combination tap assemblies incorporating brass body (various finishes) and quarter turn ceramic disc headwork with single lever operating members. The spout outlets incorporate a plastic aerator and the products are supplied with metal backnuts. Maximum working pressure 5.0 bar. Maximum operating temperature 60°C.
Range of wall mounted two-hole, single outlet (fixed) combination tap assemblies incorporating brass body (various finishes) and ceramic cartridge headwork with single lever operating members. The spout outlets incorporate a plastic aerator. Maximum working pressure 5.0 bar. Maximum operating temperature 60°C.
Two hole, single outlet fixed combination tap assembly (chromium plated brass), incorporating quarter turn ceramic disc headworks with single lever operating members. The spout outlet incorporates a plastic aeator. The product is supplied with metal back nuts. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.
Range of wall mounted, two-hole, single outlet (fixed) combination tap assemblies, comprising of a concealed rough in set with a brass body incorporating a ceramic cartridge headwork with a single lever operating member and a spout outlet. The spout outlet incorporates a plastic aerator. Maximum working pressure 10.0 Bar. Maximum operating temperature 85°C.
Page 40 of 158
We use cookies to give you the best possible experience with WRAS. Some are essential to provide website functions and ensure the website is secure. We also use cookies to help us understand how people use the site and to make improvements. Click "Accept All" to enable recommended settings or click "Manage cookies" to adjust your settings. For more details, see our Cookie Policy.
