‘EUROKOTE® 46-20’. Factory applied, red-brown coloured, two-part epoxy resin coating. Mix and apply as per manufacturer's technical data sheet 'Doc. 087' dated 01/07/2011. Cure for 7 days@20°C. For use with water up to 23°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
`Electroline ES 1212-Black`. Factory applied, black coloured, 2 part epoxy coating. Mix parts A&B in a 3:1 volume ratio. Cure for 7 days@30°C. For use with water up to 85°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the materials are not covered by the scope of the approval.
‘SIGMAPRIME 200 for use with SIGMAGUARD CSF 585 (white) or SIGMAGUARD CSF 585 (blue)’. Factory applied, white or blue coloured (once mixed and applied), two-part epoxy coating comprising of Coat 1 and Coat 2. SIGMAPRIME 200 (Coat 1) comprises of a base and hardener to be mixed in a 80:20 volume ratio. Cure for 3 days@23°C. SIGMAGUARD CSF 585 (white) or SIGMAGUARD CSF 585 (blue) is to be applied as Coat 2 and each comprises of a base and hardener to be mixed in a 77.5:22.5 ratio. Cure for 12 days@23°C. For use with water up to 23°C.
`R2 Red & R2 Blue`. Factory applied epoxy powder coatings manufactured in Changzhou. Apply as per manufacturer's instructions for use 'ANCZ-RAD-W501', 'revision no: 2' dated 'May. 5th 2021'. Cure for 10 minutes@200°C. For use with water up to 80°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Jotaguard VA 5001 Blue`, factory applied, blue coloured, fusion bonded epoxy coating. 'Jotaguard VA 5001 Red`, factory applied, red coloured, fusion bonded epoxy coating was added to the approval in June 2023. Apply both coatings as per Jotun Technical Data Sheet issued 9th November 2015. Cure for 5 minutes@245°C. For use with water up to 85°C. These materials are only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the materials are not covered by the scope of the approval.
'Kubota sulphate-resisting Portland cement'. Factory applied, grey coloured cement. Mix sand, cement and water in a mass ratio of 1:2.5:0.4. Cure for 24 hours@20°C. For use with water up to 60°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the materials are not covered by the scope of the approval.
'Kubotapowder TK1413F'. Factory applied, grey coloured epoxy resin coating. Apply as per manufacturer's instructions 'GR-294E' dated 2018/10/01. Cure for 20 minutes@180°C. For use with water up to 60°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
DHDC-7500. Grey coloured, factory applied 2-Part epoxy resin coating. Mix base (A) and hardener (B) in a ratio of 3 (A):1 (B) by weight before applying one coat by airless spray. Cure for 7 days at 25°C. For use with water up to 23°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the materials are not covered by the scope of the approval.
'CeramycGuard for use with QuartzSeal'. Site applied, white coloured (once mixed) polymer based concrete surface treatment. 'CeramycGuard’ is a three-component base coat comprising of Part A (clear liquid), Part B (grey powder) & Part C (clear liquid). Mix Parts A, B & C in a volume ratio. Rest for two minutes, apply as per manufacturer's instructions for use 'version 2' dated 'April 2021' and then cure for 24 hours@21°C. ‘QuartzSeal' is a white coloured, single-component topcoat. Apply as per manufacturer's instructions for use 'version 2' dated 'April 2021'. Cure for 7 days@21°C. For use with water up to 23°C. These materials are only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the materials are not covered by the scope of the approval.
'Brushbond FLXIII'. Site applied, grey coloured, two-part elastomeric/cementitious coating. Mix and apply in accordance with manufacturer's instructions 'v10' dated October 2020. Cure coat 1 for 18 hours@7°C. Cure coat 2 for 21 days@7°C. For use with water up to 23°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Acrylatik'. Site applied, Acrylate primers available in white, red, blue and black colours. Apply as per manufacturer's instructions 'Appendix No. 1, TU 2316-002-92 872914-2016' dated '11.02.2016'. Cure for 20 minutes@20°C and then 20 minutes@90°C. For use with water up to 23°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Superfast Potable Water (SFPW)'. Site applied, grey coloured (once mixed), two-component epoxy putty. Mix Part A (white coloured putty) with Part B (cream coloured putty) in a 1:1 mass ratio and apply as per manufacturer's instructions 'SOP Number RM1 version 1.0', dated '06/10/2022'. Cure for 24 hours@20°C. For use with water up to 23°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the materials are not covered by the scope of the approval.
'LATTYflon 2790AL'. Cream coloured, PTFE/silicone braided rope with a square cross-section. For use with water up to 23°C. For use only as a gland packing material having been tested at a reduced surface area to volume ratio.
'Solico Ivory GRP Panel'. Beige coloured, compression moulded GRP panel. For use with water up to 60°C.
'Extralite Pipe'. Light green/brown coloured GRP pipe manufactured by filament winding. For use with water up to 60°C.
'Extralite Fitting'. Brown coloured GRP fitting manufactured by hand lay-up. For use with water up to 60°C.
'JUSTLINK® JLPEX'. Single layered, off-white (translucent), extruded PEX hose. For use with water up to 60°C.
'REGZ40 & REGZ41'. White coloured silicone greases. For use with water up to 85°C.
'Hitemp 150 FG'. Natural (appears off-white/cream in colour), extruded bearing material. For use with water up to 23°C.
‘4TECH 9G22130 W-A ABK, 4TECH 9G22135 W-A ABK, 4TECH 9G22140 W-A ABK, 4TECH 9G22145 W-A ABK, 4TECH 9G22150 W-A ABK, 4TECH 9G22155 W-A ABK & 4TECH 9G22160 W-A ABK’. Black coloured, glass-fibre reinforced PA66 materials. For use with water up to 23°C.
‘4MID 9A22130 HW-A ABK, 4MID 9A22135 HW-A ABK, 4MID 9A22140 HW-A ABK, 4MID 9A22145 HW-A ABK & 4MID 9A22150 HW-A ABK’. Black coloured, glass-fibre reinforced PA66 materials. For use with water up to 23°C.
'Mapex® AN4920SN FWB50 & GITOP® G3A2 M01FWB'. Black coloured, injection moulded, glass fibre reinforced PA66 materials. For use with water up to 85°C.
'Grilon BG-30/2 natural (appears cream in colour) & Grilon BG-30/2 black 9697 (black coloured)'. Injection moulded PA-GF30 materials. Grilon BG-30/2 black 9697 is for use with water up to 85°C. Between 1st October 2020 and 10th May 2022, Grilon BG-30/2 natural was for use with water up to 23°C. Between 11th May 2022 and 31st October 2025 Grilon BG-30/2 natural is for use with water up to 60°C.
AKROMID® A3 GF 25 8 HU natural (8120) AKROMID® A3 GF 30 8 HU natural (8102) AKROMID® A3 GF 33 8 HU natural (8128) AKROMID® A3 GF 35 8 HU natural (8121) AKROMID® A3 GF 40 8 HU natural (8122) AKROMID® A3 GF 43 8 HU natural (8130) AKROMID® A3 GF 45 8 HU natural (8123) AKROMID® A3 GF 50 8 HU natural (8124) AKROMID® A3 GF 55 8 HU natural (8125) AKROMID® A3 GF 60 8 HU natural (8126) AKROMID® A3 GF 25 8 HU black (8118) AKROMID® A3 GF 30 8 HU black (8112) AKROMID® A3 GF 33 8 HU black (8129) AKROMID® A3 GF 35 8 HU black (8113) AKROMID® A3 GF 40 8 HU black (8114) AKROMID® A3 GF 43 8 HU black (8131) AKROMID® A3 GF 45 8 HU black (8115) AKROMID® A3 GF 50 8 HU black (8116) AKROMID® A3 GF 55 8 HU black (8119) AKROMID® A3 GF 60 8 HU black (8117) Natural (appears white) and black coloured, injection moulded, glass fibre reinforced PA66 materials. For use with water up to 85°C.
'Omnix DW/FC-4050 NT000'. Natural (off-white with yellow/green tint coloured), injection moulded PA material. For use with water up to 23°C.
Natural (appear white), black or grey, injection moulded, glass fibre reinforced nylon materials. Between September 2020 and February 2022 these grades are for use with water up to 85°C: Grivory HT1V-3 FWA natural. Grivory HT1V-4 FWA grey 9489. Grivory HT1V-4 FWA grey 9312. Grivory HT1V-4 FWA natural. Grivory HT1V-5 FWA Grey L1366.3. Grivory HT1V-5 FWA grey L16760.2. Grivory HT1V-4 FWA grey-blue 4637. The natural coloured Grivory may also be coloured using MB A XE 4298 black (using the recommended dosage). Between September 2020 and February 2022 these grades are for use with water up to 23°C: Grivory HT1V-3 FWA black 9225. Grivory HT1V-4 FWA black 9225. Grivory HT1V-5 FWA natural and black 9225. Grivory HT1V-6 FWA natural and black 9225. From March 2022, all grades are suitable for use with water up to 85°C.
Natural (appear white), black or grey, injection moulded, glass fibre reinforced nylon materials. Between September 2020 and February 2022 these grades are for use with water up to 85°C Grilamid LV-65H FWA black 9225. Grilamid LV-30H FWA grey 9497. Grilamid LV-30H FWA natural. Between September 2020 and February 2022 these grades are for use with water up to 23°C Grilamid LV-50H FWA natural. Grilamid LV-30H FWA black 9225. Grilamid LV-43H FWA black 9225. Grilamid LV-50H FWA black 9225. Grilamid LV-65H FWA natural. From March 2022, all grades are suitable for use with water up to 85°C.
'POLYNT 1349 TAEQ20 to be used in conjunction with POLYCOR LP PA FC CLEAR 0200'. POLYNT 1349 TAEQ20 is a polyester resin and LP PA FC CLEAR 0200 is a factory applied, gel coat (when used together the material appears light pink in colour). Apply as per manufacturer's TDS ‘7206 updated 10.10.17’. Cure for 24 hours@25°C. For use with water up to 23°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'LSPE-BE002 PE Pipe (Deep Blue)'. Blue coloured, extruded polyethylene pipe. For use with water up to 60°C.
'LSPE-BE002 PE Fitting (Deep Blue)'. Blue coloured, injection moulded polyethylene fitting. For use with water up to 60°C.
'LSPE-BK001'. Black coloured, extruded polyethylene pipe. For use with water up to 60°C.
'LSPE-BK001'. Black coloured, injection moulded polyethylene fitting. For use with water up to 60°C.
'ajpipe HDPE Pipe'. Black coloured (with blue external stripes), extruded PE100 pipe. For use with water up to 50°C. From January 2024 the pipe is for use with water up to 60°C.
'Sureline I'. Black coloured (with blue longitudinal lines), extruded PE100 pipe. For use with water up to 23°C.
'100 US Gallon Dubai Polytank Panel'. Triple layered, rotationally moulded LLDPE tank panel comprising of a white coloured inner layer, black coloured middle layer and white coloured outer layer. For use with water up to 65°C.
'Radius Systems Socket Fittings and Saddle Fittings'. Black coloured, injection moulded PE fittings. For use with water up to 60°C.
`Aqua-Plus Fittings`. Green coloured, injection moulded polypropylene fittings. For use with water up to 70°C.
'HTP-5056 Hexagonal Tube Settler'. Pale blue coloured, extruded polypropylene 'tube settler' component. For use with water up to 23°C.
'Palaplast Thermopal PP-R Pipe'. Green coloured (with dark green stripe), extruded polypropylene pipe. For use with water up to 70°C.
'Palaplast Thermopal PP-R Fitting'. Green coloured, injection moulded polypropylene fitting. For use with water up to 70°C.
'Grey H01H-00'. Grey coloured, injection moulded polypropylene material. For use with water up to 23°C.
'400-GA05'. White (translucent), injection moulded polypropylene material. For use with water up to 85°C.
`Polyfill PPC GF2007 PD1 yellow`. Yellow coloured, injection moulded polypropylene material. For use with water up to 23°C.
'GA100 natural (appears white in colour) & GC1025 (black coloured) rings'. Extruded PTFE ring shaped components. For use with water up to 85°C.
'Classic-Chromline UK Multilayer hose'. Extruded, hose which appears silver and comprises of a cream coloured PVC inner layer, white coloured polyester filament layer, black coloured PVC layer, silver coloured acrylic layer and a transparent PVC outer layer. For use with water up to 60°C.
'WS 9000'. Site applied, off-white coloured, fibre glass impregnated, polyurethane repair tape. Apply as per manufacturer's technical date sheet created '02/11/2010' and reviewed '30/01/2015'. Cure for 30 minutes@23°C. For use with water up to 23°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
‘ChemSet™ REO502 EF PLUS, Epcon™ C6 EF PLUS & Epcon™ G5 PRO’. Grey coloured, two-part epoxy resin anchor systems, comprising of a resin and hardener. The systems are supplied in a pre-weighed (resin:hardener ratio of 3:1), two-component mixing cartridge. Cure 24 hours at 7°C. For use with water up to 23°C. For use only as a resin anchor having been tested at a reduced surface area to volume ratio of 1,000mm² per 1 litre of water. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
`Butyl Liner 72612`. Black coloured, calendared butyl rubber sheet material. Shore hardness 60. Tested in-radius size 0.5mm. For use with water up to 23°C.
'EP10/7/7 BLK gaskets & 'O' rings'. Injection moulded, black coloured EPDM gaskets & 'O' rings. Shore hardness 70. The gaskets have an in-radius size of 0.75mm and for use with water up to 85°C. The ‘O’ rings have an in-radius size of 1.5mm and between 1st July 2021 and 21st September 2021, the ‘O’ rings were for use with water up to 23°C. Between 22nd September 2021 and 28th February 2026, the ‘O’ rings are for use with water up to 85°C.
'EUW-70'. Black coloured, injection moulded EPDM diaphragm. Shore hardness 70. Tested in-radius size 0.95mm. For use with water up to 60°C.
Page 37 of 222
We use cookies to give you the best possible experience with WRAS. Some are essential to provide website functions and ensure the website is secure. We also use cookies to help us understand how people use the site and to make improvements. Click "Accept All" to enable recommended settings or click "Manage cookies" to adjust your settings. For more details, see our Cookie Policy.
