Range of wall mounted, thermostatic shower valves (brass body – Chrome finish), incorporating a single sequential headwork controlling both temperature and flow using a single lever operating member. The inlets incorporate stainless-steel strainers, plastic flow regulators and approved check valve cartridges (verified by test - suitable for backflow protection against fluid category 2) Product is not supplied with shower hose, handset, overhead shower or riser rail assembly. Maximum working pressure 10.0 Bar Maximum operating temperature 60°C.
Range of T type thermostatic blending valves with (brass bodies - chrome plated finishes). The inlets incorporate a stainless-steel strainer. For use with copper pipe (BS EN 1057). Maximum working pressure 10.0 bar. Maximum operating temperature 85°C.
Range of wall mounted bar type thermostatic shower valves (brass body, chrome finish) incorporating quarter turn ceramic disc headwork which controls the flow with dome type operating members. Temperature is controlled independently via a thermostatic cartridge with dome type operating member which incorporates a manual override button. Both inlets incorporate an approved check valve cartridge however, the complete product has not been fully tested to demonstrate it provides backflow protection. Supplied with an optional flow regulator. Maximum working pressure 5.0 bar. Maximum operating temperature 85°C
Range of wall mounted thermostatic blending valves with chrome plated brass bodies and ceramic disc headwork with a dome type operating member. Temperature is controlled independently via a thermostatic cartridge also with a dome type operating member. Inlets incorporate single check valve cartridges however, the complete assembly has not been tested to demonstrate it provides adequate backflow protection. The products are supplied with a shower hose and handset. Maximum working pressure 10.0 Bar Maximum operating temperature 60.0°C
Range of wall mounted thermostatic shower valves with brass bodies (chromium plated) incorporating a ceramic disc controlling the flow to the shower (for some models it diverts the flow to a hand shower or overhead shower) using a dome type operating member. The temperature is controlled independently via a thermostatic cartridge with a dome type operating member incorporating a manual override button. Inlets incorporate stainless steel strainers and an approved single check valve cartridge; however, the complete product has not been fully tested to demonstrate it provides backflow protection. Maximum operating pressure 5.0 bar. Maximum operating temperature 50°C
Range of butterfly valves incorporating blue or green epoxy coated ductile iron bodies, discs and EPDM seals. Maximum working pressure 16.0 Bar Maximum operating temperature 65.0°C
Range of wafer or lugged butterfly valves incorporating blue epoxy coated ductile iron bodies, EPDM seats and stainless-steel discs. The LTDX71X-16Q DN40-150 size models are lever operated; all other models and sizes are gear operated. Maximum working pressure 10.0 bar or 16.0 bar. Maximum operating temperature 100°C.
Range of wafer, lugged and flanged butterfly valves with blue, black or red epoxy coated ductile iron bodies, zinc coated (galvanised) discs and EPDM seats. F700L & F703L models incorporate a hand wheel operating members and F700G & F703G incorporate a worm gear operating member. Maximum working pressure 16.0 bar. Maximum operating temperature 70°C.
Combined pre-set temperature and pressure relief valves (set at 7.0 bar) incorporating DZR brass body. The compression connection to be used with copper pipe BS EN 1057. Maximum working pressure 7.0 bar. Maximum operating temperature 95°C.
Combined pre-set temperature and pressure relief valves (set at 7.0 bar) incorporating DZR brass body. The compression connection to be used with copper pipe BS EN 1057. Maximum working pressure 7.0 bar. Maximum operating temperature 95°C.
Range of in-line pilot operated level control valves with blue epoxy coated ductile iron bodies. The products have flow control facility controlled via a float operated valve and are supplied with auxiliary components including stainless steel pipe & fittings, spherical valves, bleed valve and a needle valve. Maximum working pressure 16.0 Bar. Maximum operating temperature 60.0°C.
Range of inline pilot operated altitude control valves with blue epoxy coated ductile iron bodies and bonnets. The pilot system consists of spherical valves, in line strainers, needle valve, non-return valve, altitude gauge and a pre-set altitude control valve. The spring rating of the pilot 10-60ft (3 to 18m). Maximum working pressure 16.0 Bar Maximum operating temperature 60.0°C
Range of double swing gate, wafer, non-return valves with blue, black or red epoxy coated ductile iron bodies. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Range of swing gate, non-return valves with (blue, black or red epoxy powder coated) ductile iron bodies. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Range of non-return, swing gate valves with bronze bodies and bronze discs. Maximum working pressure 20.0 bar Maximum operating temperature 85°C.
Range of adjustable, bronze in-line pressure reducing valves. VIT-20-PRBZ ½”, ¾” & 1” & 1¼” size have inspection ports on the outlet only. 2” to 4” sizes have inspection ports on the inlet and outlet. The valves incorporate a stainless-steel strainer. Maximum inlet supply pressure 20.0 bar. Maximum outlet pressure 1.0 bar to 4.0 bar. Maximum operating temperature 70°C.
Range of pilot operated pressure relief control valves with blue epoxy coated ductile iron bodies and supplied with auxiliary components including stainless steel pipe & fittings, spherical valves, bleed valve and a needle valve. Spring ratings of pilot valve are 0.35 - 3.5 bar, 0.7 - 5.5bar, 1.38 - 13.8 bar, 6.9 - 20.7 bar Maximum working pressure 16.0 Bar Maximum operating temperature 60.0°C
Solenoid valve with a plastic body, incorporating an EPDM diaphram and EPDM sealing rings. Maximum working pressure 8.0 bar. Maximum operating temperature 65°C.
Range of inline or angled screwdriver and lever operated isolation and servicing valves (See models), (chrome plated brass bodies) and ball, incorporating EPDM ‘O’-rings. For use with copper pipe manufactured to EN1057 Maximum working pressure: 10 bar. Maximum working temperature: 99°C.
Range of spherical valves with nickel plated brass bodies and a chrome plated ball. The handle can either be a flat lever handle or a T handle (See models) Maximum working pressure 25.0, 30.0, 40.0, 50.0 Bar Maximum operating temperature 60.0°C
Wall mounted shower valve (chrome plated brass body) incorporating a ceramic cartridge headwork with a single lever operating member. The outlet incorporates an approved check valve cartridge however, the complete product has not been fully tested to demonstrate it provides backflow protection. Maximum working pressure 10.0 Bar Maximum operating temperature 65.0°C
Range of lockable, key operated, in-line spherical valves with brass bodies and nickel-plated brass ball. Maximum working pressure 16.0 Bar. Maximum operating temperature 85.0°C.
Range of electronically actuated ball valves with brass bodies, chromium plated copper balls, PTFE and silica gel seals. Maximum working pressure 16.0 Bar. Maximum operating temperature 100°C.
Range of inline brass bodied or chrome plated brass bodied spherical valves, with a chrome plated brass ball and EPDM ‘O’-rings. SVB66MB and SV44MB models are lever operated. SV66MBC and SVT64MBC are screwdriver operated. The products are for use with PE-X pipe (manufactured to BS 7291-3), PB pipe (manufactured to BS 7291-2) and copper pipe (manufactured to EN 1057). Maximum working pressure 10.0 bar. Cold water use only.
Range of flanged gate valves with blue epoxy coated ductile iron bodies and EPDM O-rings and disc. The valves are operated via a non-rising spindle headwork with a wheel type operating member. Maximum working pressure 16.0 Bar
Non-metallic materials and components comply with BS6920 at 80°C
Range of gate valves with blue epoxy coated ductile iron bodies and hand wheel operating members. Maximum working pressure 25.0 bar (DN50-DN300) or 10.0 bar (DN400 only) Maximum operating temperature 85ºC
AMEXSA range of resilient seated gate valves with blue epoxy coated ductile iron bodies and bonnets and ductile iron wedges encapsulated in EPDM. The valves are operated via a non-rising spindle with a hand wheel operating member. Maximum working pressure 16.0 bar. Maximum operating temperature 80°C.
Range of in-line pilot operated control valves with blue epoxy coated ductile iron bodies, having rate of flow control facility controlled via a pilot system. Spring ratings of pilot valve are 2 to 20 psi / 0.138 to 1.38 bar, 25 to 50 psi / 1.72 to 3.4 bar. Maximum working pressure 16.0 Bar Maximum operating temperature 60.0°C
Range of gate valves incorporating either rising or non-rising spindle headworks and PTFE gaskets and Bronze body, bronze wedge and handwheel. Maximum working pressure 20.0 bar. Maximum operating temperature 85°C.
Range of blue or green polyethylene coated ductile iron gate valves incorporating an EPDM Wedge. The valves operate via a non-rising spindle headwork with hand wheel operating member. Maximum working pressure 16.0 Bar Maximum operating temperature 65.0°C
Range of resilient seated gate valves with cast iron bodies (blue epoxy coated), EPDM coated cast iron wedges and a handwheel operating member. Maximum working pressure 16.0 bar.
Non-metallic materials and components comply with BS6920 at 85°C
Range of hand wheel operated gate valves with blue epoxy coated ductile iron bodies and EPDM wedges. Maximum working pressure 10.0 Bar or 16.0 Bar Maximum operating temperature 40.0°C
Range of hand wheel operated gate valves with blue epoxy coated ductile iron bodies, ductile iron wedge encapsulated in EPDM. Maximum working pressure 16.0 Bar Maximum operating temperature 65.0°C
Range of handwheel operated bronze bodied stop valves. Maximum working pressure 20.0 bar. Maximum operating temperature 85°C.
Range of inline plastic bodied screw down stop valves incorporating a non-rising spindle headwork with a dome type operating member. The products are for use with PE-X pipe (manufactured to BS 7291-3) and copper pipe (manufactured to EN 1057). Maximum working pressure 10.0 bar. Cold ater use only.
Range of inlet control groups with a DZR brass body, consisting of a pressure reducing valve and pressure relief valve set to 6bar. The outlet incorporates a single check valve cartridge verified by test (suitable for backflow protection against Fluid Category 2. Pressure reducing range 1 bar to 6 bar Maximum working pressure 10 Bar Maximum operating temperature 85°C
Range of inlet control valves with DZR brass bodies. The valves consist of an adjustable pressure reducing valve set at 3.0 bar, pressure relief valve set at either 4.5, 6.0 or 8.0 bar. The valves also incorporate an approved check valve cartridge, verified by test (suitable for backflow protection against Fluid Category 2). For use with copper pipe to BS EN 1057. Maximum working pressure 16.0 Bar. Maximum operating temperature 65°C.
Range of double regulating valves available with bronze bodies. Products incorporate a non-rising spindle headwork. Products also include two test ports. Maximum working pressure 25.0 bar. Maximum operating temperature 85°C.
In-line electrolytic scale reducer with copper bodies for use with copper pipe (manufactured to BS EN 1057). Maximum working pressure 10.0 bar. Maximum operating temperature 40°C.
Range of water conditioners with stainless steel bodies. Maximum working pressure 10 Bar. Maximum operating temperature 85°C.
'ZHR‐SRC'. Factory applied, grey coloured Sulphate Resistant cement. Mix cement and sand in a 2:1 mass ratio. Apply as per manufacturer's instruction sheet '2025.8.27'. Steam cure for 8 hours@50°C. For use with water up to 65°C.
'Ecocoat FBE Green Powder PFC/6018 (RAL 6018)& Ecocoat FBE Red Oxide Powder PFC/3000-Red Oxide'. Factory applied, green or red coloured epoxy coatings. Apply as per manufacturer’s Product Data Sheet revised ‘1st Jan, 2024’. Cure for 3 minutes at a metal temperature of 230°C. For use with water up to 85°C. These materials are only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the materials are not covered by the scope of the approval.
‘Eurokote® 48-20 Brun Rouge’. Factory applied, red coloured, two-part epoxy coating. Mix resin and hardener in a 2.13:1 mass ratio and apply as manufacturer's TDS dated '10/12/2024'. Cure for 24 hours@20°C. For use with water up to 23°C.
'Epilux 610 T Primer for use with Epilux 155 SF Topcoat'. Factory applied, white coloured (once applied) two-part epoxy coating. The topcoat can also be used alone, without the primer. 'Epilux 610 T Primer’ comprises of a base & hardener to be mixed in a 3:1 volume ratio and then applied as per manufacturer's TDS 'SEPTEMBER 2018 VERSION 1'. Cure for 16 hours@25°C – 28°C, 60%±10% RH. 'Epilux 155 SF Topcoat' comprises of a base & hardener to be mixed in a 4:1 volume ratio and then applied as manufacturer's TDS 'SEPTEMBER 2018 VERSION 1'. Cure for 7 days@25°C – 28°C, 60%±10% RH. For use with water up to 60°C. This material is only approved for the RH, mixing & curing conditions that appear on the approval. If the RH, mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'PMSP5112-M, PMSP5113-M, PMSP5114-M, PMSP5115-M, EP5112D01SC, EP5113D01SC, EP5114D01SC & EP5115D01SC'. Factory applied, blue coloured, Porcelain Vitreous Enamel coatings. Apply as per manufacturer's User Manual 'PEM 37', 'Edition 01', dated '14/10/2020'. Cure for 5 minutes@840°C. For use with water up to 85°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'NMSP2251M, NMSP2265M, NMSP2266-M, NMSP2267-M, ER2251A01SM, ER2265A01SM, ER2266A01SC, ER2267A01SC'. Factory applied, blue coloured, Porcelain Vitreous Enamel coatings. Apply as per manufacturer's User Manual 'PEM 38', 'Edition 01', dated '14/10/2020'. Cure for 5 minutes@840°C. For use with water up to 85°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'L-01 GP Blue-grey Enamel'. Factory applied, blue-grey coloured Enamel coating. Apply as per manufacturer's TDS 'Version: 01', dated '2025-01-02'. Cure for 15 minutes@200°C and then fire for 10 minutes@850°C. For use with water up to 85°C. This material is only approved for the curing/firing conditions that appear on the approval. If the cure/fire conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Epilux 610 T Primer for use with Epilux 155 SF Topcoat'. Factory applied, white coloured (once applied) two-part epoxy coating. The topcoat can also be used alone, without the primer. 'Epilux 610 T Primer’ comprises of a base & hardener to be mixed in a 3:1 volume ratio and then applied as per manufacturer's TDS 'Ver.3 Aug 25'. Cure for 16 hours@25°C – 28°C, 60%±10% RH. 'Epilux 155 SF Topcoat' comprises of a base & hardener to be mixed in a 4:1 volume ratio and then applied as manufacturer's TDS 'Ver2 Aug 25'. Cure for 7 days@25°C – 28°C, 60%±10% RH. For use with water up to 60°C. This material is only approved for the RH, mixing & curing conditions that appear on the approval. If the RH, mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
‘Nitcote CM 210’. Site applied, two-part, grey coloured (once applied), Cementitious Waterproofing coating. Mix ‘CM 210 white’ liquid polymer and ‘CM 210 grey’ powder in a 1:3.6 weight ratio and apply two coats as per manufacturer's TDS 'UAE/0210/23/Z-1'. Cure Coat 1 for 3 hours@35°C and Coat 2 for 21 days@23°C. For use with water up to 65°C. This material is only approved for the mixing & curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
‘Nitocote EP 405’. Site applied, two-part,white coloured epoxy based Waterproofing coating. Mix 3.1 litres of the base with 0.9 litres of hardener and apply as per manufacturer’s TDS ‘UAE/0228/22/K’. Cure for 7 days@20°C. For use with water up to 23°C. This material is only approved for the mixing & curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
Page 228 of 233
We use cookies to give you the best possible experience with WRAS. Some are essential to provide website functions and ensure the website is secure. We also use cookies to help us understand how people use the site and to make improvements. Click "Accept All" to enable recommended settings or click "Manage cookies" to adjust your settings. For more details, see our Cookie Policy.
