'Fosroc Nitoseal SC600'. Site applied, grey coloured silicone sealant waterstop. Apply as per manufacturer's TDS issue '1.0', dated October 2024. Cure for 21 days at 7°C. For use with water up to 23°C. This material is only approved for the mixing & curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval. These materials are for use in concrete reservoirs and similar structures, constructed in accordance with the design criteria of BS EN 1992-3:2006 (Design of concrete structures – Liquid retraining and containing structures) with respect to normal frequency of joints. The material has been tested at a reduced surface area to volume ratio of 1000mm² per litre.
'Loctite 5800'. Red coloured anaerobic adhesive. Apply as per manufacturer's technical data sheet dated April 2012. For use with water up to 85°C. These products are to be applied and cured in strict accordance with the manufacturer's instructions
Range of wall mounted, two-hole, single outlet (fixed) electronically controlled tap assemblies (chromium plated brass). The flow is controlled by a solenoid valve activated via infra-red sensor. Temperature is controlled independently via a thermostatic cartridge with a dome operating member which incorporates a manual override button. The spout outlets incorporate plastic aerators, and both inlets incorporate an approved single check valve cartridge (however, the complete assembly has not been fully tested to demonstrate that it provides adequate backflow protection) and stainless-steel strainers. Maximum working pressure 10.0 Bar. Maximum operating temperature 60.0°C.
Range of deck mounted, single hole, single outlet (fixed) electronically controlled tap assemblies (chromium plated brass). Flow is controlled by a solenoid valve activated via an infra-red sensor. The spout outlet incorporates a plastic aerator. The main body incorporates a plastic flow regulator and stainless steel strainer prior to the solenoid. The inlets to the main body of the GS10, CM10 & GH10 model variants incorporate approved check valve cartridges, however, the complete product has not been fully tested to demonstrate it provides backflow protection. These models also have a manual temperature control operated by a single lever on the side of the body. The inlet hoses incorporate a TPE gasket. The models are supplied with or without a pop-up waste. The GS20 & GM20 model variants are single feed. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.
Range of deck mounted, single hole, single outlet (fixed) electronically controlled tap assemblies (chromium plated brass). Flow is controlled by a solenoid valve activated via an infra-red sensor. The spout outlet incorporates a plastic aerator. The inlets to the main body of the M10, GC10, MX10, A10 & L10 model variants incorporate an approved check valve cartridge, however, the complete product has not been fully tested to demonstrate it provides backflow protection, these models also have a manual temperature control operated by a single lever on the side of the body. The inlet hoses incorporate a stainless steel strainer (M10, GC10, MX10, A10 & L10 model variants) or combined TPE washer and stainless strainer (M20, GC20, A20 & L20 model variants). The models are supplied with or without a pop-up waste. The M20, GC20 A20 & L20 model variants are single feed. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.
Range of deck mounted, single hole, single outlet (fixed) electronically controlled tap assemblies (chromium plated brass). Flow is controlled by a solenoid valve activated via an infra-red sensor. The spout outlet incorporates a plastic aerator. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.
Non-verifiable double check valve assembly consisting of two spring loaded resilient trim in-line check valve cartridges housed in a DZR brass body. Maximum working pressure 16 Bar Maximum operating temperature 65°C
Non-verifiable double check valve assemblies incorporating two spring loaded resilient trim in-line check valve cartridges, DZR brass bodies (brushed chrome) and a drain port located in between the cartridges. The assemblies incorporate spherical valve. Maximum working pressure 10.0 bar. Maximum operating temperature 90°C.
Range of aerators with plastic bodies and EPDM ‘O’-rings. Maximum operating temperature 65°C Open outlet use only
Range of ceramic cartridge headworks with plastic bodies. For insertion into specifically dimensioned bores. Maximum working pressure 10.0 bar. Maximum operating temperature 65°C
Range of ceramic disc headworks with brass bodies. For insertion into specifically dimensioned bores. Maximum working pressure 5.0 bar. Maximum operating temperature 85°C.
Ceramic cartridge headworks with a plastic body, incorporating silicone seals. The product is intended for insertion into specifically dimensioned tap assemblies. Maximum working pressure - 10 Bar Maximum operating temperature - 85 °C
Range of thermostatic cartridges with either brass or plastic bodies, for insertion into specifically dimensioned bores. Maximum operating temperature 85°C.
Range of single hole, single outlet, (swivel), combination tap assemblies (brass bodies – various finishes), incorporating a ceramic cartridge headwork and single lever operating member. The outlet is a pull-down spray type and incorporates a plastic aerator. Maximum working pressure 8.6 bar. Maximum operating temperature 60°C
Range of single hole, single outlet (swivel) pullout spray combination tap assembly (brass bodies – various finishes), incorporating ceramic cartridge headworks with single lever operating members. The outlet incorporates a plastic aerator. Maximum working pressure 5.0 Bar Maximum operating temperature 60.0°C
Range of single hole, single outlet fixed combination tap assemblies (brass body with various finishes), incorporating a ceramic cartridge headwork with either a single lever or cross top operating member. The spout outlets incorporate a plastic aerator. Products are supplied with PEX inner-lined grey plastic braided inlet hoses. Maximum working pressure 10 bar.
Non-metallic materials and components comply with BS6920 at 60°C
Range of single hole, single outlet (fixed) combination tap assemblies (brass bodies - various finishes) incorporating a ceramic cartridge headworks with single lever operating members. The spout outlet incorporates a plastic aerator. Supplied with a pop-up waste. Maximum working pressure 5.0 Bar. Maximum operating temperature 60°C.
Single hole, single outlet (fixed) combination tap assembly (chrome plated brass body) incorporating a ceramic cartridge headwork with single lever operating member. The spout outlet incorporates a plastic aerator. The product is supplied with a click-type pop up waste (not verified by test). Maximum working pressure 8.0 bar. Maximum operating temperature 65°C.
Range of single hole, single outlet (fixed) combination tap assemblies, (brass bodies – various finishes). Model WJ IX008A has a stainless-steel body. Incorporating a ceramic cartridge headworks with single lever operating members. Models WJ 6181000XX & WJ 6181700XX have dome type operating members. The spout outlets incorporate plastic aerators. Maximum working pressure 5.0 Bar Maximum operating temperature 60.0°C
Range of single-hole, single outlet (fixed) combination tap assemblies (chrome plated brass bodies), incorporating a ceramic cartridge headwork with single lever operating members. The spout outlets incorporate plastic aerators. Supplied with a lever type pop up waste. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.
Single hole, single outlet (fixed) combination tap assembly (brass body with various finishes) incorporating quarter turn ceramic disc headworks with cross type operating member. The spout outlet incorporates a plastic aerator. Maximum working pressure 5.0 Bar. Maximum operating temperature 60°C.
Range of single hole, single outlet (fixed) combination tap assembies (stainless steel bodies, various finishes - see model) incorporating a ceramic cartridge headwork with a single lever operating member. The spout outlet incorporates a plastic aerator. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.
Range of single hole, single outlet (swivel) combination tap assemblies (various plated brass), incorporating quarter turn ceramic disc headwork with single lever operating members. The spout outlets incorporate a plastic flow straightener. Maximum working pressure 10.0 Bar Maximum operating temperature 65.0°C
Range of single hole, single outlet (swivel) combination tap assemblies (brass bodies - various finishes), incorporating ceramic cartridge headworks with lever type operating members. The spout outlet incorporates a plastic aerator. Maximum working pressure 5.0 Bar Maximum operating temperature 60.0°C
Range of single-hole, single outlet (swivel) combination tap assemblies (brass bodies - various finishes), incorporating a ceramic cartridge headworks with single lever operating members. The spout outlet incorporates a plastic aerator. The products are supplied mounting kit that comprises of stainless-steel braided hoses and isolation valves that incorporate approved single check valve cartridges, however, the complete assembly has not been fully tested to demonstrate it provides backflow protection. Maximum working pressure 5.0 bar. Maximum operating temperature 65°C
Range of single-hole, single outlet (swivel) combination tap assemblies (brass bodies -various finishes), incorporating a ceramic cartridge headwork with a single lever operating member. The spout outlet incorporates a plastic aerator. The products are supplied mounting kit that comprises of stainless-steel braided hoses and isolation valves that incorporate approved single check valve cartridges, however, the complete assembly has not been fully tested to demonstrate it provides backflow protection. Maximum working pressure 5.0 bar. Maximum operating temperature 60°C
Range of wall mounted two-hole, single outlet (fixed) combination tap assemblies (brass bodies with various finishes) incorporating a ceramic cartridge headwork with single lever operating member. The spout outlets incorporate an aerator. Maximum working pressure 5.0 bar. Maximum operating temperature 60°C.
‘Arco,’ ‘Zero,’ ‘Slim’ & ‘Trenta9’ ranges of wall mounted two-hole, single outlet (fixed) combination tap assemblies (chromium plated brass), incorporating a ceramic cartridge headwork and either a single lever operating member (Trenta9 models) or dome type operating member (all other models). The spout connection of the Arco models incorporates a plastic flow regulator. The spout outlet of all other models incorporates a plastic aerator. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.
Two hole, single outlet fixed combination tap assembly (chrome plated brass body) incorporating quarter turn ceramic disc headworks with single lever operating members. The spout outlet incorporates a plastic flow straightener. The product is supplied with metal backnuts. Maximum working pressure 5.0 bar. Maximum operating temperature 60°C.
two-hole, single outlet (fixed) combination tap assembly (chromium plated brass), incorporating a quarter turn ceramic disc headwork controlling the flow using a dome type operating member. Temperature is controlled via a thermostatic cartridge also using a dome type operating member with a manual override button, and the product also incorporates a manual diverter to shower outlet. The inlets incorporate a stainless-steel strainer and an approved check valve cartridge however, the complete product has not been fully tested to demonstrate it provides backflow protection. The spout outlet incorporates a plastic aerator. Maximum working pressure 5.0 bar. Maximum operating temperature 60°C
Two hole, single outlet (fixed) combination tap assembly (chrome plated brass body) incorporating quarter turn ceramic disc headworks with single lever operating members and a manual diverter to a shower outlet. The spout outlet incorporates a plastic flow straightener. The product is supplied with metal backnuts and a shower hose and handset. Maximum working pressure 5.0 Bar. Maximum operating temperature 60°C.
Range of two-hole, single outlet (fixed) combination tap assemblies (chrome plated brass bodies) incorporating quarter turn ceramic disc headworks with single lever operating members and a manually operated diverter to shower outlet. The spout outlet incorporates a plastic flow straightener. The product is supplied with metal backnuts and a shower hose and handset. Maximum working pressure 5.0 bar. Maximum operating temperature 60°C.
Range of two-hole, single outlet (fixed) combination tap assemblies with chromium plated brass bodies, incorporating quarter turn ceramic disc headworks with single lever operation members and a self-cancelling diverter to shower outlet. Products are supplied with metal backnuts, shower handsets and shower hoses, with spout outlets incorporating plastic aerators. The shower outlets also incorporate approved check valve cartridges, however, the complete products have not been fully tested to demonstrate they provide backflow protection. Maximum working pressure 10 bar. Maximum operating temperature 60°C.
Range of wall mounted, two-hole, single outlet combination tap assemblies, (brass bodies - various finishes,) incorporating a half turn ceramic disc headwork diverting flow between bath and shower positions and a thermostatic cartridge controlling the temperature independently, both with dome type operating members. The product also incorporates a self-cancelling diverter to a shower handset. The product is supplied with an overhead shower outlet, shower hose and handset. The spout outlet incorporates a plastic aerator. Each inlet incorporates an approved check valve cartridge, however, the complete product has not been fully tested to demonstrate it provides backflow protection. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.
Wall mounted two-hole, single outlet (swivel) combination tap assembly (chromium plated brass body), incorporating half turn ceramic disc headworks and dome type operating members. Maximum working pressure 5.0 Bar. Maximum operating temperature 85.0°C.
Two-hole, single outlet (swivel) combination tap assemblies (brass bodies - various finishes). Incorporating quarter turn ceramic disc headworks and single lever type operating members. The spout outlet incorporates a plastic aerator, and the products are supplied with metal backnuts. Maximum working pressure 10.0 Bar Maximum operating temperature 65.0°C
Two hole, single outlet fixed combination tap assembly (chrome plated brass body) incorporating quarter turn ceramic disc headworks with single lever operating members and a manually operated diverter to shower outlet. The spout outlet incorporates a stainless steel mesh strainer. The product is supplied with a shower hose and handset and metal backnuts. Maximum working pressure 5.0 bar. Maximum operating temperature 60°C.
Range of three hole, single outlet (fixed) combination tap assembles (brass bodies - various finishes). Incorporating ceramic cartridge headworks with single lever operating members. The spout outlet incorporates a plastic aerator. Maximum working pressure 5.0 Bar. Maximum operating temperature 60°C.
Range of three hole, single outlet (fixed) combination tap assemblies, (brass bodies - various finishes) incorporating quarter turn ceramic disc headworks with various operating members. The spout outlet incorporates a plastic aerator and is connected to the headworks via stainless steel braided TPSiV lined hose assemblies Maximum working pressure 3.5 bar. Maximum operating temperature 60°C
Three-hole, single outlet (swivel) combination tap assembly (brass bodies - various finishes). Incorporating quarter turn ceramic disc headworks with single lever operating members. The products are also supplied with stainless steel braided EPDM lined flexible hose assemblies, intended for use between the side body valves and spout. The spout outlet incorporates a plastic aerator. Maximum working pressure 10.0 Bar Maximum operating temperature 65.0°C
Five-hole, single outlet (fixed) combination tap assembly (brass body with various finishes – see models), incorporating quarter turn ceramic disc headworks with dome type operating members and a self-cancelling diverter to shower outlet. The product is supplied with stainless steel braided, PEX lined interconnecting flexible hose assemblies. The shower handset incorporates an approved check valve cartridge; however, the complete product has not been fully tested to demonstrate it provides backflow protection. Maximum working pressure: 10.0 Bar. Maximum operating temperature: 60.0°C.
Range of four-hole, single outlet, fixed, combination tap assemblies (brass bodies - various finishes) incorporating quarter turn ceramic disc headworks with various operating members (see models). The products incorporate a self-cancelling diverter to shower outlet. The spout outlets incorporate a plastic flow straighter. The product is not supplied with a shower hose and handset. Maximum working pressure 5.0 Bar. Maximum operating temperature 60°C.
Range of shower outlets (brass bodies - various finishes) comprising of a wall union, shower fixing bracket and a wall elbow. Models WEPB Incorporates an approved check valve cartridge, however, the complete product has not been fully tested to demonstrate it provides backflow protection. Maximum working temperature 65°C. Open outlet use only
Range of wall mounted spout outlets (brass bodies - various finishes). Maximum operating temperature 60°C Open outlet use only.
Range of CU type press copper crimp fittings with EPDM ‘O’-rings for use with copper tube manufactured to EN 1057. The joints are achieved by means of a crimping tool. For above ground use. Maximum working pressure: 16.0 bar. Maximum operating temperature: 85°C
Range of press fittings (brass bodies - various finishes) with stainless steel press (‘TH’ profile) collars and EPDM O-rings for use with “EA” range of PEX/AL/PEX multilayer pipe (for press fitting connections and compression for EHA adaptor fittings only) or copper pipe manufactured to EN1057 (compression connections). Maximum operating temperature: 95°C. Maximum operating pressure: 10 bar.
‘FRABOPRESS BIG-SIZE’ range of copper and bronze press fittings for use with copper pipe (manufactured to EN1057). Maximum working pressure 10.0 bar. Maximum operating temperature 100°C
‘FRABOPRESS COPPER M’ range of copper and bronze press fittings for use with copper pipe (manufactured to EN 1057). Maximum working pressure 16.0 bar. Maximum operating temperature 100°C.
‘FRABOPRESS 316 M’ range of stainless-steel press fittings for use with stainless steel pipe (manufactured to EN 10312:2002 & EN 10217:2021). Maximum working pressure 16.0 bar. Maximum operating temperature 100°C.
Range of copper crimped fittings with EPDM ‘O’-rings for use with copper pipe manufactured to EN1057. For above and below ground use. Maximum working pressure 16 Bar. Maximum operating temperature 99°C.
Page 194 of 225
We use cookies to give you the best possible experience with WRAS. Some are essential to provide website functions and ensure the website is secure. We also use cookies to help us understand how people use the site and to make improvements. Click "Accept All" to enable recommended settings or click "Manage cookies" to adjust your settings. For more details, see our Cookie Policy.
