'334701 - EPDM peroxide 70'. Black coloured, compression moulded EPDM material. Shore hardness 70. Tested in-radius size 1.0mm. For use with water up to 85°C.
'TamPur 150'. Site applied, Hydrophilic polyurethane foam which is an amber coloured liquid when unreacted and a pale yellow coloured, flexible foam material when cured. Mix TamPur 150 with water in a volumetric ratio of 1:1 and apply as per manufacturer’s TDS 'V1UK19 – 2019.4.25'. Cure for 24 hours at 7°C. For use with water up to 23°C. This material is only approved for the mixing & curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval. These materials are for use in concrete reservoirs and similar structures, constructed in accordance with the design criteria of BS EN 1992-3:2006 (Design of concrete structures – Liquid retraining and containing structures) with respect to normal frequency of joints. The material has been tested at a reduced surface area to volume ratio of 1000mm² per litre.
Range of wall mounted, single-hole, single outlet, electronically controlled combination tap assemblies, (chrome plated brass or stainless steel bodies). The flow is controlled by a solenoid valve activated via an infra-red sensor. The spout outlet incorporates a plastic aerator. The products incorporate a stainless steel braided PEX lined flexible hose assembly, connecting the spout to the solenoid valve. Maximum working pressure 8.0 Bar.
Non-metallic materials and components comply with BS6920 at 65°C
Side entry BS1212-4 fill valves with plastic bodies. Maximum working pressure 10.0 bar. Coldwater use only.
Range of bottom entry BS1212-4 telescopic fill valves with plastic bodies. Maximum working pressure 10.0 bar. Cold water use only.
Floor mounted single hole, single outlet (fixed), combination tap assembly (chromium plated brass), incorporating a ceramic cartridge headwork with a single lever operating member and a manual diverter to shower outlet. The spout outlet incorporates a plastic aerator or flow straightener. The product is supplied with a shower hose and handset. Maximum working pressure - 10 Bar
Non-metallic materials and components comply with BS6920 at 65°C
Spring loaded resilient trim check valve cartridge with stainless steel spring and EPDM `O`-ring. For insertion into specifically dimensioned bores. Maximum working pressure 16 Bar. BS6920 at 85°C
Range of non-verifiable double check valve assemblies consisting of two spring loaded resilient trim in-line check valve cartridges housed in DZR brass bodies. Maximum working pressure 16.0 bar Maximum operating temperature 85°C
Range of ceramic cartridge headworks with plastic bodies, incorporating silicon and NBR‘O’-rings, for insertion into specifically dimensioned bores. Maximum working pressure 10 bar. Maximum operating temperature 85°C.
Range of ceramic cartridge headworks with plastic bodies and NBR seals and O-rings. For insertion into specifically dimensioned bores. Maximum working pressure 5.0 Bar
Non-metallic materials and components comply with BS6920 at 85°C
Range of ceramic cartridge headworks with plastic bodies & silicone rubber seals. For insertion into specifically dimensioned bores. Maximum working pressure 10.0 bar. Maximum operating temperature 85°C
Thermostatic cartridges with plastic or brass bodies, and EPDM ‘O’ rings and stainless steel strainers. For insertion into specifically dimensioned bores. Maximum working pressure 10.0 bar. BS6920 85°C.
Range of single hole, single outlet (fixed) combination tap assemblies ( brass bodies - various finishes), incorporating either a ceramic cartridge or ceramic disc (see models) headworks with either a single lever or cross top (see models) operating member. The spout outlet incorporates either a plastic aerator, a plastic flow straightener or an open outlet type spout (see models). Some models are supplied with a click type waste and some are supplied with a lever type pop-up waste (see models). Maximum working pressure 5.0 Bar or 10.0 Bar (see models) Maximum operating temperature 65.0°C or 85.0°C (see models)
Range of single hole, single outlet (fixed) combination tap assemblies ( brass bodies - various finishes), incorporating either a ceramic cartridge or ceramic disc (see models) headworks with either a single lever or cross top (see models) operating member. The spout outlet incorporates either a plastic aerator, a plastic flow straightener or an open outlet type spout (see models). Some models are supplied with a click type waste and some are supplied with a lever type pop-up waste (see models). Maximum working pressure 5.0 Bar. Maximum operating temperature 65.0°C.
Single hole, single outlet (fixed) combination tap assembly (chromium plated brass) incorporating a sequential headwork controlling both flow and temperature with single lever type operating member. The spout outlet incorporates a plastic flow straightener. Maximum working pressure 5.0 Bar. Maximum operating temperature 85°C.
Wall mounted single hole, single outlet (fixed) combination tap assembly, brass body(various finishes), incorporating a detent headwork that controls both flow and temperature with a single lever operating member. The spout outlet incorporates a plastic aerator. The product also incorporates a permanently open waste outlet. Maximum working pressure 10.0 bar
Non-metallic materials and components comply with BS6920 at 60°C
Range of single hole, single outlet (fixed) combination tap assemblies with brass bodies (various finishes - see model), incorporating a ceramic cartridge headwork with a single lever operating member. The spout outlet incorporates a plastic aerator. The 48 000 xxx model is supplied with a pop-up waste. The 48 001 xxx and 48 002 xxx models are supplied with an open waste/non-closing waste. Maximum working pressure 10.0 bar.
Non-metallic materials and components comply with BS6920 at 60°C
Single-hole, single outlet, fixed, combination tap assembly with (brass body - various finishes), incorporating a ceramic cartridge headwork with a single lever operating member. The spout outlet incorporates a plastic aerator. The product is supplied with a lever type pop-up waste. Maximum working pressure 10 Bar
Non-metallic materials and components comply with BS6920 at 60°C
Floor mounted single hole, single outlet (swivel), combination tap assembly (chromium plated brass), incorporating a ceramic cartridge headwork with a single lever operating member and a manual diverter to shower outlet. The spout outlet incorporates a plastic flow straightener. This product is supplied with shower hose, shower handset and PEX inner-lined braided inlet hoses. Maximum working pressure 10.0 bar.
Non-metallic materials and components comply with BS6920 at 65°C
Two hole, single outlet (fixed) combination tap assemblies (chrome or matte black plated brass) incorporating quarter turn ceramic disc headworks with single lever operating member. The spout outlet incorporates a plastic aerator. This product is supplied with metal backnuts. Maximum working pressure 10.0 bar.
Non-metallic materials and components comply with BS6920 at 65°C
Page 164 of 311
We use cookies to give you the best possible experience with WRAS. Some are essential to provide website functions and ensure the website is secure. We also use cookies to help us understand how people use the site and to make improvements. Click "Accept All" to enable recommended settings or click "Manage cookies" to adjust your settings. For more details, see our Cookie Policy.
