Range of concealed thermostatic valves with thermostatic cartridges. Models (XB-AZ-034B & XB-AZ-035B) consist of quarter turn ceramic disc headworks controlling the flow and the temperature is controlled independently via thermostatic cartridge. Model (XB-AZ-037B) consists of a two-way diverter cartridge controlling the flow and a thermostatic cartridge controlling the temperature. Model (XB-AZ-038B) consists of a three-way diverter cartridge controlling the direction of flow, a thermostatic cartridge controlling the temperature and a quarter turn ceramic disc controlling the flow. All models incorporate cube, dome, cross-top or single lever type operating members. The inlets incorporate stainless steel strainers and single check valve cartridges; however, the complete products have not been fully tested to demonstrate it provides backflow protection. Maximum working pressure 10.0 bar. Maximum operating temperature 65°C.
Range of wall mounted exposed shower valves (Brass bodies – various finishes), incorporating single sequential headworks controlling both flow and temperature with single a single lever operating member. Models (BPMO SHXVO C & BPRR SHXVO C) incorporate non-rising spindle headworks controlling the flow with single lever operating members. The temperature is controlled independently via a thermostatic cartridge with cross-top operating members. The inlets incorporate flow regulators, plastic strainers and approved single check valve cartridges however, the complete product has not been fully tested to demonstrate that it provides backflow protection. Models (Mini TS1203 RR C, R2 SHXRR C & KN2 SHXRR C) are supplied with riser rails and overhead shower outlets. Models (R2 SHXVO C, BPRO SHXVO C & BPMO SHXVO C) valve only. All other models are supplied with shower hose, handset and riser rail assemblies. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.
Range of wall mounted, bar shower mixers, (chrome plated brass bodies) incorporating a thermostatic cartridge controlling the temperature with either dome or cubed type operating members that incorporate manual override buttons and quarter turn ceramic disc headworks controlling the flow with dome or cubed type operating members. The inlets incorporate stainless steel strainers and approved single check valve cartridges, however, the complete product has not been fully tested to demonstrate it provides backflow protection. Maximum working pressure - 6 Bar. Maximum operating temperature - 65°C.
Range of wall mounted thermostatic shower valves, (brass bodies - various finishes) incorporating two push button headworks controlling the flow to the hand shower or overhead shower outlet. The temperature is controlled independently via a thermostatic cartridge with single lever operating member which incorporates a manual override button. The inlets incorporate stainless steel strainers and approved single check valve cartridges however, the complete product has not been fully tested to demonstrate it provides backflow protection. Maximum working pressure 10.0 Bar Maximum operating temperature 70.0°C
Range of wall mounted, concealed, thermostatic shower valves (brass bodied - chrome plated trim set), flow is controlled via a solenoid valve that is activated by an infrared sensor or touch sensor. The temperature is controlled independently via a thermostatic cartridge with a dome type operating member that incorporates a manual override button. The inlets incorporate stainless steel strainers and approved single check valve cartridges, however, the complete products have not been fully tested to demonstrate they provide backflow protection. Maximum working pressure 8.0 Bar. Maximum operating temperature 65.0°C
Range of wafer, lug type and double flanged butterfly valves incorporating blue epoxy coated ductile iron bodies, either stainless steel (CF8 or CF8M) or blue epoxy coated ductile iron discs and an EPDM seat. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Non-metallic materials and components comply with BS6920 at 85°C
Range of wafer, lug type and double flanged butterfly valves incorporating blue epoxy coated ductile iron bodies, either stainless steel (CF8 or CF8M) or blue epoxy coated ductile iron discs and an EPDM seat. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Non-metallic materials and components comply with BS6920 at 85°C
Range of flow control valves with epoxy coated ductile iron bodies. Auxiliary components include a needle valve, pressure reducing pilot valve and isolation valves. Maximum supply pressure 16.0 bar. Outlet pressure setting is adjustable in the range 0.6 to 1.2 bar. Maximum operating temperature 65°C.
Range of pilot operated basic valves, main body only, with epoxy coated ductile iron bodies. Maximum operating pressure 16.0 bar. Maximum operating temperature 65°C.
Range of pressure relief valves with plastic bodies and EPDM diaphragms and ‘O’-rings, Factory pre-set at 3.0 bar. Maximum operating temperature 110°C.
Range of lever or butterfly operated spherical valves with DZR brass bodies (CCDZR). Incorporating DZR brass ball. For use with copper pipe BS EN 1057. Maximum working pressure 25.0 Bar. Maximum operating temperature 99.0°C
Range of spherical valves with DZR brass bodies and chromium plated balls. Maximum working pressure 30.0 bar. Maximum operating temperature 85°C.
Range of in-line lever operated spherical valves with stainless steel bodies, stainless steel ball and PTFE seats. Maximum working pressure 30 Bar. Maximum operating temperature 85 °C.
Range of lever, handle or square operated (see models) spherical valves with brass bodies, incorporating PTFE seats and a brass ball with a red coating. Maximum working pressure 40.0 Bar Maximum operating temperature 95.0°C
Range of inline or angled servicing valves incorporating a white (-W and -01 suffix models) or grey (all other models) plastic body, chrome plated brass ball, EPDM washers and EPDM ‘O’-rings. The products are either lever operated (-H and -01 suffix models) or screwdriver operated (all other models). Push fit connections are for use with copper pipe (manufactured to EN 1057), John Guest BPEX pipe or PEX barrier pipe (manufactured to BS EN 7291-3) and John Guest BPB or polybutylene barrier pipe (manufactured to BS EN 7291-2). Maximum working pressure and operating temperature: 13.24 bar @ 20°C, 6.0 bar @ 65°C.
Range of resilient seated gate valves with cast iron bodies (blue epoxy coated), EPDM coated cast iron wedges and a handwheel operating member. Maximum working pressure 16.0 bar.
Non-metallic materials and components comply with BS6920 at 85°C
Range of non-rising spindle gate valves (brass bodies), with PTFE stem packing and gaskets. Operating members are handwheel operated.
Range of non-rising spindle gate valves with bronze, brass or DZR brass (ART 606) bodies, incorporating hand wheel or key operated operating members. Maximum working pressure 16.0 Bar (ART 333) 25.0 bar
Non-metallic materials and components comply with BS6920 at 85°C
Range of resilient seated gate valves with blue epoxy coated ductile iron bodies, and an EPDM wedge, gasket and ‘O’-ring. The 3233 model has a rising spindle, the 3243 model has a non-rising spindle, both have a handwheel operating member. Maximum working pressure 25.0 bar. Maximum operating temperature 85°C.
Range of gate valves with ductile iron bodies (blue epoxy coated), EPDM discs and non-rising spindles with hand wheel operating members. Maximum working pressure 10.0 Bar Maximum operating temperature 80.0°C
Range of angled valves with brass bodies (some models chrome plated). Maximum working pressure 10 bar. Maximum operating temperature 65°C
Range of motorised position pilot operated control valves with epoxy coated ductile iron bodies and stainless-steel pipework and fittings. Maximum operating pressure 16.0 bar. Maximum operating temperature 65°C.
Range of manually operated balancing valves with blue epoxy coated ductile iron bodies, incorporating EPDM ‘O’-rings and PTFE washers. Available in the following options: DN65-DN150 sizes: DZR brass sleeve. DN65-300 sizes: blue epoxy coated ductile iron sleeve. DN65-DN150 sizes: bronze disc. DN65-300 sizes: blue epoxy coated ductile iron disc. DN200-DN300 sizes: Stainless steel (SUS304) disc. DN200-DN300 sizes: Stainless steel (SUS304) stem. DN65-DN300 sizes: Stainless steel (SUS420) stem. DN65-DN150 sizes: brass stem. The product incorporates a test port on each flange and are adjusted using a handwheel. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
‘Ballorex’ range of regulating valves with DZR brass bodies, PTFE seats, EPDM ‘O’-rings and washer. The product incorporates two test ports. Maximum working pressure 25.0 bar. Maximum operating temperature 85°C.
Range of electrolytic water conditioning units consisting of stainless-steel tube with a copper/zinc alloy sacrificial anode and brass inlet and outlet connections. Compression models are for use with copper pipe (manufactured to BS EN 1057). Maximum working pressure 16.0 bar. Maximum operating temperature 100°C.
Range of ultraviolet disinfection units with stainless-steel bodies. Maximum working pressure 10.0 bar. Maximum operating temperature 40°C.
'HYDRALFUN AC BLEU PAM RAL5005-CZL8190'. Factory applied, blue coloured acrylic paint. Apply as per manufacturer's TDS dated February 2024. Cure for 21 days@23°C. Between April 2024 and July 2024, the paint is for use with water up to 50°C. From August 2024 the paint is for use with water up to 60°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Loctite PC 7255 GN (Green) coating for use with Bonderite M-NT 1455-W primer'. Factory applied, green coloured, two-component epoxy resin coating. In June 2025 ‘LOCTITE PC 7255 GY (Grey) coating for use with BONDERITE M-NT 1455 Primer-W Coating’ was added to the approval. Factory applied, grey coloured, two-component epoxy resin coating. Prime the surface to be coated with the Bonderite primer wipe. Mix and apply as per manufacturer’s TDS dated October 2016. Cure for 7 days@23°C at 45% relative humidity. For use with water up to 85°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Balinit Milubia'. Factory applied, dark grey coloured, two layered coating system consisting of a titanium bottom layer & diamond like coating top layer. Apply as per manufacturer`s instructions '080224' dated 08-Feb-2024. No curing required. For use with water up to 85°C.
‘Corroless ACO Brush Grades RAL5005 (GB861) and Light Green (GB206)’ (formerly known as 'Acothane Brush Grades Blue & Green'). Site applied, blue or green coloured, two-part polyurethane coatings consisting of an amber coloured, liquid activator and blue or green coloured coating. Mix brush grade and activator in a 3.24:1 weight ratio. Apply as per technical data sheet dated Feb 2020. Cure for 14 days@7°C. For use with water up to 23°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mix and cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Interline 975 White'. Site applied, two-part epoxy coating which can be applied as one coat or three coats. Mix parts A & B in a 2.2:1 and apply as per manufacturer's TDS 'Ref:4236', 'Issue Date: 04/02/2015'. When applied as a single coat, the coating must be cured for 14 days at 10°C. When applied as a three-coat system, the coating must be cured as follows: coat 1 = 24 hours@10 °C, coat 2 = 24 hours@10 °C & coat 3 = 14 days@10 °C. For use with water up to 23°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Strongcoat EPW-P'. Site applied, two-component, light grey coloured (once applied) epoxy coating. Mix Part A (light grey coloured liquid) with Part B (orange coloured liquid) in a 8.1:3.78 volume ratio and apply coat 1 as per manufacturer's TDS 06-0020-A-2021. Cure for 24 hours@23°C. Mix and apply coat 2 in the same way as coat 1 and cure for 7 days@23°C. For use with water up to 23°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
‘Sika MonoTop®-1010’, one-part cementitious bonding primer for use with ‘Sika MonoTop®-615’ one-part cementitious repair mortar. Mix ‘Sika MonoTop®-1010’ with tap water in the ratio of 25kg:5.25 litres. Apply as per manufacturer’s Product Data Sheet ‘020302020010000054, March 2021, Version 01.01’. Mix ‘Sika MonoTop®-615’ with tap water in the ratio of 25kg:3.8 litres and apply immediately to ‘Sika MonoTop®-1010’ as per manufacturer’s Product Data Sheet ‘020302040030000198, December 2021, Version 02.02’. Cure for 21 days@7°C. For use with water up to 23°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Vinoleo SS'. Colourless lubricant to be applied in accordance with manufacturer's TDS reference '163460 version 2'. For use with water up to 85°C.
Range of wedge shoes (part numbers 2005036, 2006536, 2008036, 2010036, 2012536, 2015036, 2020036, 2025036, 2030036, 2040036, 2650036, 2660036, 40005036, 40006536, 40008036, 40010036, 40015036, 40020036, 40025036, 2680036 & 126100036). Black coloured, injection moulded nylon wedge shoes. For use with water up to 50°C.
RIAMAXX HT 325 GF20 natur N88FWC. RIAMAXX HT 325 GF25 natur N88FWC. RIAMAXX HT 325 GF30 natur N88FWC. RIAMAXX HT 325 GF35 natur N88FWC. RIAMAXX HT 325 GF40 natur N88FWC. RIAMAXX HT 325 GF45 natur N88FWC. RIAMAXX HT 325 GF50 natur N88FWC. RIAMAXX HT 325 GF20 schwarz R88FWC. RIAMAXX HT 325 GF25 schwarz R88FWC. RIAMAXX HT 325 GF30 schwarz R88FWC. RIAMAXX HT 325 GF35 schwarz R88FWC. RIAMAXX HT 325 GF40 schwarz R88FWC. RIAMAXX HT 325 GF45 schwarz R88FWC. RIAMAXX HT 325 GF50 schwarz R88FWC. Natural (appears beige/brown) and black coloured, injection moulded, glass filled polyamide materials. For use with water up to 85°C.
'Ultradur® B4300 G6 FC Aqua Uncolored'. Uncoloured (appears cream), injection moulded PBT material. For use with water up to 85°C.
'Hyperzone HY4008'. Off-white coloured, compression moulded PE material. For use with water up to 23°C.
`TORELINA A604WR G & TORELINA A604WR B'. Grey coloured and black coloured, injection moulded PPS materials (manufactured in Japan). For use with water up to 85°C.
‘TORELINA™ A604WR & TORELINA™ A604WR B’. Natural (appears beige) and black coloured, injection moulded PPS materials (manufactured in China). For use with water up to 85°C
‘ECOTEC tubsed® TS.50/TS.85'. Black coloured, extruded polypropylene water channel component. Shore hardness 74. For use with water up to 23°C.
'40-5048'. White coloured (translucent), injection moulded, polypropylene 'Filter Frame' component. For use with water up to 45°C.
‘GFPP-(1) SFKP (2)’. White coloured, injection moulded, glass fibre reinforced PP material. (1) 2 digits represent the amount of fiberglass added to the material with a range of 5% - 50%. (2) is an internal code used to denote customer and is replaced with a 4 digit number between 0001 & 9999. For use with water up to 85°C.
'SP-402M'. Black coloured, compression moulded natural rubber material. Shore hardness 78. Tested in-radius size 1.0mm. For use with water up to 60°C.
'EPDM 9611 'O' rings'. Black coloured, compression moulded EPDM 'O' rings. Shore hardness 60. Tested in-radii sizes between 0.48mm & 2.0mm. For use with water up to 85°C.
'TJJH-EPDM gasket'. Black coloured, compression moulded EPDM gasket. Shore hardness 70. Tested in-radius size 1.2mm. Between April 2024 and March 2025, the gasket was for use with water up to 23°C. Between April 2025 and April 2029, the gasket is for use with water up to 65°C.
'EP801324C'. Black coloured, compression moulded EPDM rubber material. Shore hardness 80. Tested in-radius size 1.0mm. For use with water up to 85°C.
'LSR 8220, LSR 8230, LSR 8240, LSR 8250, LSR 8260 & LSR 8270'. Natural (clear coloured), compression moulded liquid silicone rubber materials. Shore hardness between 20 & 70. Tested in-radius size 1.0mm. For use with water up to 85°C.
`Loctite 587`. Blue coloured silicone sealant. Apply as per manufacturer`s TDS dated November 2004. Cure for 7 days at 7°C. For use with water up to 85°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Griffon UNI-100'. Amber coloured solvent cement intended to join PVC pipe and fittings. Apply as per manufacturer's instructions. Cure for 24 hours@7°C. For use with water up to 23°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
Page 70 of 131
We use cookies to give you the best possible experience with WRAS. Some are essential to provide website functions and ensure the website is secure. We also use cookies to help us understand how people use the site and to make improvements. Click "Accept All" to enable recommended settings or click "Manage cookies" to adjust your settings. For more details, see our Cookie Policy.
