Range of concealed, wall mounted thermostatic blending valves with brass bodies (chromium plated trim set). The product incorporates a ¼ turn ceramic disc or a 2 way manual diverter with shut-off position to control the flow, with dome type operating members.The temperature is controlled independently via thermostatic cartridges, with dome type operating members. The inlets incorporate approved check valve cartridges, however, the complete products have not been fully tested to demonstrate they provide backflow protection. Maximum working pressure: 5 Bar. Maximum operating temperature: 60°C.
Wall mounted concealed three way diverter valve assembly (brass bodies with trim sets in various finishes). Maximum working pressure 10 bar. Maximum operating temperature 70°C
Range of wall mounted, concealed thermostatic blending valves (brass bodies - various finishes), incorporating non-rising spindle headworks controlling the flow using dome type operating members. Temperature is controlled via a thermostatic cartridge with a manual override button and a dome type operating member. The products are supplied with approved single check valve cartridges however, the complete product has not been fully tested to demonstrate that it provides adequate backflow protection. Maximum working pressure 10 Bar. 10 755 xx0 and 36 702 xx0 - Maximum operating temperature 60°C All other models Maximum operating temperature 70°C
Range of butterfly valves with blue epoxy coated ductile iron bodies and discs, and EPDM seals with a wheel type operating member. Maximum working pressure 16.0 Bar Maximum operating temperature 85.0°C
Non-metallic materials and components comply with BS6920 at 85°C
Range of wafer, lug type and double flanged butterfly valves incorporating blue epoxy coated ductile iron bodies, either stainless steel (CF8 or CF8M) or blue epoxy coated ductile iron discs and an EPDM seat. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Non-metallic materials and components comply with BS6920 at 85°C
Range of bronze swing gate valves incorporating a bronze disc with a metal-to-metal seal. Maximum working pressure 20.0 bar. Maximum operating temperature 85°C.
Range of angle valves (brass bodies – various finishes), incorporating non-rising spindle headworks with a dome type operating members and NBR O-rings and PTFE Seals. Maximum working pressure 10 bar. Maximum operating temperature – Cold Water Use
Range of spherical valves with nickel plated brass bodies, chromium plated brass balls and various operating members (see models). Products incorporate EPDM O-rings and PTFE seats. Maximum working pressure ½” – 1” 30 bar, 1 ¼” – 2” 25 bar. Maximum operating temperature 100°C.
Range of lever operated spherical valves with brass bodies (chromium plated), incorporating chromium plated balls and PTFE seats. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Range of spherical valves with stainless steel bodies, chrome plated brass ball and PTFE seats. Maximum working pressure 68.9Bar.
Non-metallic materials and components comply with BS6920 at 85°C
Range of lever or butterfly operated spherical valves with DZR brass body and ball. Maximum working pressure: 40.0 Bar Maximum operating temperature 99.0°C
Range of lever or butterfly operated spherical valves with brass, DZR brass or nickel-plated brass. Incorporating brass or nickel-plated brass ball. For use with copper pipe BS EN 1057. Maximum working pressure 25.0 Bar. Maximum operating temperature 99.0°C
Range of lever or butterfly operated spherical valves with brass or nickel plate bodies and ball. Maximum working pressure: Various – see model section. Maximum operating temperature 99.0°C
Range of lever operated spherical valves with DZR brass or stainless-steel bodies and ball. Models beginning with ‘GP’ and ‘GPH’ are for use with copper pipes (manufactured to EN 1057). Models beginning with ‘GPMS’ and ‘GPHS’ are for use with stainless steel (SS316L) pipe (manufactured to EN 10312). Maximum working pressure 25.0 bar. Maximum operating temperature 85°C
Range of spherical valves incoporaintg either brass (CP5R models) or nickel plated (CP12 models) brass bodies with chrome plated brass ball and operated via lever, butterfly type handle or screwdriver slot. For use with copper pipe (manufactured to EN1057). Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Range of spherical valves with nickel plated brass bodies, brass ball, and NBR ‘O’-rings with lever (LL1031 and LL1064 models), extended lever (LL1529 model) or butterfly (LL1043 model) operating members. The compression connections are for use with copper pipe manufactured to EN1057. Maximum working pressure 25.0 bar. Maximum operating temperature 85°C.
Range of spherical valves with chrome plated brass bodies and chrome plated brass balls, incorporating PTFE seats. Maximum working pressure for model 340: 40.0 bar ¼”- 2” & 25.0 bar 2”- 4” Maximum working pressure for all other models 40.0 bar Maximum operating temperature: 100℃
Range of full port spherical valves with DZR brass bodies, chrome plated or (VIR REDOX) coated brass ball (see model). The products are either lever or handle operated (see model). The 33FFDRE models include a stem extension. Maximum working pressure 32.0 bar. Maximum operating temperature 100°C (wholesome water use), 130°C (closed circuit use only).
Range of spherical ball valves with black plastic bodies, PTFE seats and EPDM ‘O’-rings. Maximum working pressure: 16 Bar. Cold Water use only.
Range of gate valves incorporating blue epoxy coted ductile iron bodies, ductile iron wedges encapsulated in EPDM and an EPDM gasket and seal. The valves are operated via a non-rising spindle with a hand wheel operating member. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Range of non-rising resilient stem seated gate valves with epoxy coated bodies and EPDM wedge. Maximum working pressure 16 bar. Cold water use only.
Range of non-rising spindle gate valves with bronze, brass or DZR brass (MV40-1116) bodies, incorporating hand wheel or key operated operating members. Maximum working pressure 16.0 Bar (MV40-1153) 25.0 bar
Non-metallic materials and components comply with BS6920 at 85°C
Range of gate valves incorporating blue epoxy coated ductile iron bodies, epdm coated ductile iron wedges, EPDM gasket and seal. The valves are operated via a non-rising spindle with a hand wheel operating member. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Range of gate valves with brass bodies and stems, EPDM O-rings, with non-rising spindles with hand wheel operating members. Maximum working pressure 20.0 bar. Maximum operating temperature 100°C.
Range of gate valves incorporating DZR brass bodies, spindle headwork and hand wheel operating member. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C
Range of gate valves with brass bodies, bonnets and non-rising stems, with hand wheel or lockshield operating members. Maximum working pressure: 16.0 bar. Maximum operating temperature: 85°C
Range of IVR 605 gate valve with brass bodies, PTFE or NBR packing. The valves operate via a non-rising spindle headwork with hand wheel operating members. Maximum working pressure 16.0 bar. Maximum operating temperature 23°C.
Screw down stop valve with either gunmetal, stainless steel or brass bodies (see model), EPDM seals and ‘O’-rings and seal washer. 135020 prefix and 0731G0 prefix models have a drain port fitted with an EPDM ‘O’-ring. Maximum working pressure 16.0 Bar. Maximum operating temperature 85°C.
Range of bedpan washing & disinfection machines. The flow is controlled by a solenoid valve and discharged via a type `AB` airgap (verified by test - suitable for backflow protection against fluid category 5). Maximum working pressure - See models Maximum operating temperature - 90 °C
Range of commercial washing machines with flow controlled by solenoid valves and discharged via type AB air gap assembly (verified by test - suitable for backflow protection against fluid category 5). The inlets incorporate approved check valve cartridges, however, the complete product has not been fully tested to demonstrate it provides backflow protection Maximum working pressure 5 Bar. Maximum operating temperature 60°C.
Range of inline water conditioners with stainless steel bodies and catalytic alloy core. Maximum working pressure 16.0 bar. Maximum operating temperature 100°C.
'ELECTROCOAT BP 1119'. Factory applied, black coloured Bituminous Paint. Apply as per manufacturer's TDS Document No: 'ECL/ TDS / BP-1119-Bituminous Paint', Issue Date '10-Aug-20', Version No: '01'. Cure for 12 minutes at 45°C, followed by 10 hours at 28°C. For use with water up to 65°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'JERLAC Bituminous sealer coat black'. Factory applied, black coloured Bitumen coating. Apply as per manufacturer's TDS reference 'BN433', dated '27/07/2023', revision '00'. Cure for 12 hours@30°C. For use with water up to 60°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
‘PRIMER NATZINC EP9015 SC PART A’ Primer for use with ' HYDRALFUN AC BLEU PAM RAL5005-CZL8190 ' top-coat. Factory applied, blue coloured (once applied) primer and finish-coat. Mix base:hardener of primer in a 100:10 weight ratio and apply as per manufacturer’s TDS February 2024. Then apply top-coat as per manufacturer’s TDS February 2024. Cure for 21 days@23°C. For use with water up to 50°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Transpoxy Guard 472'. Factory applied, two-part, creamy white coloured epoxy resin coating. Mix base and hardener in a mass ratio of 4:1 and apply as per manufacturer's TDS dated 'January 2017'. Cure for 7 days@23°C. For use with water up to 23°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'XX-CM Sulphate Resisting Cement'. Factory applied, grey coloured cement mortar. Mix cement:sand:water in a 1.0:2.0:0.4 weight ratio and apply as per manufacturer's TDS '004', dated '2023.02.01'. Air cure for 4 hours at 23°C and the vapour cure for 6 hours at 60°C. For use with water up to 65°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'XX-CM5 Blast Furnace Slag Cement'. Factory applied, grey coloured cement mortar. Mix cement:sand:water in a 1.0:2.0:0.4 weight ratio and apply as per manufacturer's TDS '002', dated '2023.02.01'. Air cure for 4 hours at 23°C and the vapour cure for 6 hours at 60°C. For use with water up to 65°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Sikafloor® P 649 and Sikalastic® M 649 Coating'. Factory applied, grey coloured (once mixed), two-component primer (non-water contact primer) and two-component coating (water contact coating). Mix and apply Sikafloor® P 649 primer as per Product Data Sheet ‘MBS_CC-UAE/Sl_P_649_04_24’. Cure for 2 hours@25°C. Then mix and apply Sikalastic® M 649 Coating as per Product Data Sheet ‘MBS_CC-UAE/Sl_M_649_06_21/v3/01_24/v4/03_24’. Cure for 1 minute@25°C. For use with water up to 85°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'PP8000 M62091'. Factory applied, blue coloured enamel coating. Apply as per manufacturer's data sheet version '01-2018'. Cure for 7 minutes@840°C. For use with water up to 85°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified then the material is not covered by the scope of the approval.
'JERLAC Solventless Epoxy Grey'. Factory applied, grey coloured, two-component Epoxy coating. Mix Base:Curing Agent in a 2:1 volume ratio and apply as per manufacturer's TDS reference 'BN434', dated '24/07/2023', revision '01/03.12.2025'. Cure for 7 days@30°C. For use with water up to 85°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'MS 520B'. Factory applied, dark grey coloured enamel coating. Apply as per manufacturer's instructions 'ref. PRO PR 15 Gi 01 UK' dated April 04, 2024. Cure for 10 minutes@850°C. For use with water up to 85°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
‘Sikagard®-180’. Site applied, grey coloured, two-component epoxy coating consisting of Part A (grey coloured liquid) and Part B (colourless liquid). Mix Part A and Part B in a mass ratio of 87:13 and apply as per manufacturer's TDS 'MBS_CC-UAE/Pr_180_05_18/v9/02_22/v10/05_23/v11/01_24'. Cure coat 1 for 36 hours@20°C. Cure coat 2 for 21 days@20°C. For use with water up to 40°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
‘Sikadur-Combiflex® SG System’ comprising of ‘Sikadur® 31 DW’ epoxy adhesive to be used in conjunction with ‘Sika Combiflex® SG Membrane’. ‘Sikadur® 31 DW’ is a site applied, grey coloured, two-part epoxy adhesive consisting of Part A (white coloured) and Part B (black coloured). Part A and Part B are mixed in a weight ratio of 3:1, applied and cured for 14 days@30°C. ‘Sika Combiflex® SG Membrane’ is a modified flexible Polyolefin (FPO) waterproofing tape to be applied over the adhesive and is approved as the water contact layer. Apply as per ‘Sikadur-Combiflex® SG System’ System Product Data Sheet, ‘Edition: 24/10/2012, Identification no: 02 07 03 02 System, Version: GCC’. For use with water up to 50°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Therma-Light Touch Up Paint'. Site applied, black coloured coating. Apply as per manufacturer's TDS 'TDS/CLP-L 44', dated '28/2/2024'. Cure for 7 days@22°C. For use with water up to 60°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
‘Sikagard®-1814 - RAL 7035’. Site applied, grey coloured (once mixed), two-component epoxy polysulfide resin coating. Mix Part A (light grey, opaque liquid) and Part B (light yellow, translucent liquid) in a 78:22 weight ratio and apply 2 coats as per manufacturer’s TDS ‘MBS_CC-UAE/Pr_1814_06_23/v1/01_24’. Cure coat 1 for 9 hours@25°C. Cure coat 2 for 14 days@25°C. For use with water up to 50°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
‘Sika Monotop 1010’ primer for use with ‘Sika Monotop 4012’ cement mortar. Site applied, grey coloured cementitious, polymer modified coating material used as bonding primer and cementitious, fibre reinforced, low shrinkage repair mortar. First coat: Mix 25kg ‘Sika Monotop 1010’ with 5.25 litres of water and apply as per manufacturer’s ‘Sika Monotop 4012' IFU issue no. ‘001’ dated ‘July 2022’. Second coat: Mix 25kg ‘Sika Monotop 4012’ with 3.8 litres of water and apply immediately to the first coat as per manufacturer’s IFU issue no. ‘001’ dated ‘July 2022’. Cure for 21 days@7°C. For use with water up to 23°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Klinger K49'. Black coloured, braided compression packing. For use with water up to 85°C. For use only as a gland packing material having been tested at a reduced surface area to volume ratio.
'OKS 1035/1'. Colourless (transparent) Silicone Oil lubricant. Apply as per manufacturer's Product Information dated '13.02.2024'. Between March 2024 and July 2024, the material is for use with water up to 60°C. Between August 2024 and March 2029, the material is for use with water up to 85°C.
'RADILON® A HS 164 NT'. Natural (appears white), injection moulded, unfilled, Polyamide 66 material. For use with water up to 65°C.
RADILON® AESTUS T1 RV400RKC 106 NT. RADILON® AESTUS T1 RV500RKC 106 NT. RADILON® AESTUS T1 RV400RKC 306 BK. RADILON® AESTUS T1 RV500RKC 306 BK. Natural (appears brown/yellow) and black coloured, injection moulded glass fibre filled Polyamide 6T/6I materials. For use with water up to 85°C.
Page 67 of 131
We use cookies to give you the best possible experience with WRAS. Some are essential to provide website functions and ensure the website is secure. We also use cookies to help us understand how people use the site and to make improvements. Click "Accept All" to enable recommended settings or click "Manage cookies" to adjust your settings. For more details, see our Cookie Policy.
